Quiz 6 Op-Amp Characteristics
|
|
- Naomi Simpson
- 5 years ago
- Views:
Transcription
1 Lecture Week 11 Quiz 6: Op-Amp Characteristics Complex Numbers and Phasor Domain Review Passive Filters Review Active Filters Complex Impedance and Bode Plots Workshop
2 Quiz 6 Op-Amp Characteristics Please clear desks and turn off phones and put them in back packs You need a pencil, straight edge and calculator 10 minutes Keep eyes on your own paper Follow the same format as for homework
3 Complex/Phasor Impedance Combing frequency dependent and frequency independent passive components introduces the concept of complex impedance. Complex Number: Z = x + iy x = Resistive Part (Frequency independent) iy = Reactance Part (Frequency dependent)
4 Complex Impedance The Phasor Machine will take a time domain function and will give a frequency domain complex function. The resultant function is what we call the impedance. C dv C dt PHASOR MACHINE 1 jwc R PHASOR MACHINE R
5 Capacitor Phasor Domain Proof I is a complex number V is a complex number Assume V = e jwt Then: (1) I = C dv dt (2) C d dt ejwt = jwce jwt (3) I = jwcv (4) V I = 1 jwc
6 Complex Impedance Analysis steps By following these steps you can analyze an RC circuit in the complex/phasor domain 1. Convert every component to its phasor domain representation 2. Find the equivalent impedance by adding individual impedances in series or in parallel 3. Calculate the unknown variable by using ohms law, voltage divider, KCL or KVL
7 Passive Low-Pass Filter Analysis Lets find the equation for for the Low-pass filter circuit using KCL and complex impedance at node Vout. Vin R Vout Vin Z1 = R Vout C Z2 = 1 = I 2 I jwc 2 I 1 I 1 1 jwcr + 1 Complex Impedance Eq. Low- pass filter
8 Passive High-Pass Filter Analysis Lets find the equation for for the High-pass filter circuit using KCL and complex impedance at node Vout. Vin C I 1 I 2 Vout R Vin Z1 = 1 jwc I 1 I 2 Vout Z2 = R = jwcr jwcr + 1 Complex Impedance Eq. High-pass filter
9 Bode Plots and Cutoff frequency A bode plot tell us the magnitude of the RC filter with respect to a range of frequencies. It is a useful graphical tool to determine where the amplitude of the output is starting to drop. The equation to find the frequency at which the amplitude will start to drop is give by the following equation: f c = 1 2πRC (Cutoff frequency)
10 Low-Pass Filter: Bode Plot Vin R Vout C low pass filter = 1 jwcr + 1 Complex Impedance Eq.
11 High-Pass Filter: Bode Plot Vin C R Vout high pass filter = jwcr jwcr + 1 Complex Impedance Eq.
12 Bandpass Filter: Bode Plot = 1 (jwc 2 R 2 + 1) Complex Impedance Eq. jwr 1 C jwr 1 C 1
13 Active Filters An active filter not only gets rid of unwanted frequencies, but it also amplifies those signals that we want A passive filter will only get rid of unwanted frequencies The higher the order of the filter, the more aggressive the roll off will be (the range of frequencies where the amplitude of the signal decreases will be shorter) Active VS Passive
14 Active Filters Cutoff Frequencies An active filter will still amplify signals after the cutoff frequency is reached DO NOT assume that the filter will jump straight to zero after it has hit its cutoff frequency STILL AMPLYFING
15 Making Sense of a Bode Plot Everything above 0 db means amplification or > 0 db means no change or = Everything below 0 db means diminishment or <
16 In-Class Exercise: Active Low-Pass Filter using KCL at node A and complex impedance C Vin R1 I 1 I 2 A R2 Vout = R 2 R 1 1 (jwcr 2 + 1) Complex Impedance Eq. Complex Impedance Eq. Which R contributes to the filtering part, and which contribute to the amplification part?
17 Active High-Pass Filter using KCL at node A and complex impedance. R2 Vin R1 C I 1 A I 2 Vout jwcr 1 = R 2 /R jwr 1 C Complex Impedance Eq.
18 Low-Pass Active Filter: Bode Plot = R 2 R 1 1 (jwr 2 C + 1) Complex Impedance Eq.
19 High-Pass Active Filter: Bode Plot = R 2 R 1 jwcr jwr 1 C Complex Impedance Eq.
20 Band-Pass Active Filter: Bode Plot = R 2 1 jwr 1 C 1 R 1 (jwc 2 R 2 + 1) 1 + jwr 1 C 1 Complex Impedance Eq.
21 COMPLEX IMPEDANCE MODELS FIRST ORDER First Order LOW PASS HIGH PASS PASSIVE = 1 jwcr + 1 = jwcr jwcr + 1 ACTIVE = R 2 R 1 1 (jwr 2 C + 1) = R 2 R 1 jwr 1 C 1 + jwr 1 C SECOND ORDER **Notice the common components for all types of low pass filters and for all types of high pass filters**
22 COMPLEX IMPEDANCE MODELS FIRST ORDER All low pass filters have this expression: = 1 jwcr + 1 SECOND All high ORDER pass filters have this expression: = jwcr jwcr + 1
23 10 minute Break
24 Workshop
25 P1. Find the complex impedance equation for the Active High-Pass Filter using KCL at node A. R2 Vin R1 C A I 2 I 1 Vout
26 What s Next in Week 12? Will introduce LAB Module VII Pressure Sensor LECTURE Quiz #7 Active Filters Review: Active Filters Complex Impedance High order filters Filter Design Please bring laptops to all lectures and labs.
27 Questions?
Lecture Week 10. Quiz #7 Op-Amps II Homework P17 and P18 Active Filters Active Filters Analysis Active Filters Bode Plots Filter Design Homework
Lecture Week 10 Quiz #7 Op-Amps II Homework P17 and P18 Active Filters Active Filters Analysis Active Filters Bode Plots Filter Design Homework Quiz 7 Op-Amp II(20 pts.) Please clear desks and turn off
More informationLecture Week 7. Quiz 4 - KCL/KVL Capacitors RC Circuits and Phasor Analysis RC filters Workshop
Lecture Week 7 Quiz 4 - KCL/KVL Capacitors RC Circuits and Phasor Analysis RC filters Workshop Quiz 5 KCL/KVL Please clear desks and turn off phones and put them in back packs You need a pencil, straight
More informationLecture Week 8. Quiz #5 KCL/KVL Homework P15 Capacitors RC Circuits and Phasor Analysis RC filters Bode Plots Cutoff frequency Homework
Lecture Week 8 Quiz #5 KCL/KVL Homework P15 Capacitors RC Circuits and Phasor Analysis RC filters Bode Plots Cutoff frequency Homework Quiz 5 KCL/KVL (20 pts.) Please clear desks and turn off phones and
More informationIntroduction to Complex Impedance. Passive Low Pass Filter (1 st order) Passive High Pass Filter. Active Low Pass Filter. Active High Pass Filter
Introduction to Complex Impedance for Passive Low Pass Filter ( st order) Passive High Pass Filter ( st order) Active Low Pass Filter ( st order) Active High Pass Filter ( st order) Active Low Pass Filter
More informationHomework KCL/KVL Review Bode Plots Active Filters
Homework KCL/KVL Review Bode Plots Active Filters Homeworkdue 3/6 (Najera), due 3/9 (Quinones) SUCCESS POINTS: REPORT WRITING CHECK TO MAKE SURE EVERYTHING YOU SAY REFER DIRECTLY TO YOUR TABLES AND GRAPHS?
More informationEE1305/EE1105 Homework Problems Packet
EE1305/EE1105 Homework Problems Packet P1 - The gate length of a tri-gate transistor is 22 nm. How many gate lengths fit across a human hair with a diameter of 100 μm? Show all units and unit conversions
More informationLecture Week 5. Quiz #2 Ohm s Law Homework Power Review Shorthand Notation Active Components Ideal Op-amps
Lecture Week 5 Quiz #2 Ohm s Law Homework Power Review Shorthand Notation Active Components Ideal Op-amps Quiz 2 Ohm s Law (20 pts.) Please clear desks and turn off phones and put them in back packs You
More information3.4 The Single-Loop Circuit Single-loop circuits
25 3.4 The Single-Loop Circuit Single-loop circuits Elements are connected in series All elements carry the same current We shall determine The current through each element The voltage across each element
More informationLecture Week 4. Quiz 2 Ohm s Law Series Circuits Parallel Circuits Equivalent Circuits Workshop
Lecture Week 4 Quiz 2 Ohm s Law Series Circuits Parallel Circuits Equivalent Circuits Workshop Quiz 2 - Ohm s Law Please clear desks and turn off phones and put them in back packs You need pencil, straight
More informationFREQUENCY RESPONSE AND PASSIVE FILTERS LABORATORY
FREQUENCY RESPONSE AND PASSIVE FILTERS LABORATORY In this experiment we will analytically determine and measure the frequency response of networks containing resistors, AC source/sources, and energy storage
More informationLecture Week 4. Homework Voltage Divider Equivalent Circuit Observation Exercise
Lecture Week 4 Homework Voltage Divider Equivalent Circuit Observation Exercise Homework: P6 Prove that the equation relating change in potential energy to voltage is dimensionally consistent, using the
More informationAssist Lecturer: Marwa Maki. Active Filters
Active Filters In past lecture we noticed that the main disadvantage of Passive Filters is that the amplitude of the output signals is less than that of the input signals, i.e., the gain is never greater
More informationDesigning Information Devices and Systems II Fall 2018 Elad Alon and Miki Lustig Homework 4
EECS 16B Designing Information Devices and Systems II Fall 2018 Elad Alon and Miki Lustig Homework 4 This homework is solely for your own practice. However, everything on it is in scope for midterm 1,
More informationKent Bertilsson Muhammad Amir Yousaf
Today s topics Analog System (Rev) Frequency Domain Signals in Frequency domain Frequency analysis of signals and systems Transfer Function Basic elements: R, C, L Filters RC Filters jw method (Complex
More informationEK307 Active Filters and Steady State Frequency Response
EK307 Active Filters and Steady State Frequency Response Laboratory Goal: To explore the properties of active signal-processing filters Learning Objectives: Active Filters, Op-Amp Filters, Bode plots Suggested
More informationEECS40 RLC Lab guide
EECS40 RLC Lab guide Introduction Second-Order Circuits Second order circuits have both inductor and capacitor components, which produce one or more resonant frequencies, ω0. In general, a differential
More informationEE 3305 Lab I Revised July 18, 2003
Operational Amplifiers Operational amplifiers are high-gain amplifiers with a similar general description typified by the most famous example, the LM741. The LM741 is used for many amplifier varieties
More informationLecture 2 Analog circuits. Seeing the light..
Lecture 2 Analog circuits Seeing the light.. I t IR light V1 9V +V IR detection Noise sources: Electrical (60Hz, 120Hz, 180Hz.) Other electrical IR from lights IR from cameras (autofocus) Visible light
More informationHomework Assignment 03
Homework Assignment 03 Question 1 (Short Takes), 2 points each unless otherwise noted. 1. Two 0.68 μf capacitors are connected in series across a 10 khz sine wave signal source. The total capacitive reactance
More informationLecture 2 Analog circuits. Seeing the light..
Lecture 2 Analog circuits Seeing the light.. I t IR light V1 9V +V IR detection Noise sources: Electrical (60Hz, 120Hz, 180Hz.) Other electrical IR from lights IR from cameras (autofocus) Visible light
More informationEK307 Passive Filters and Steady State Frequency Response
EK307 Passive Filters and Steady State Frequency Response Laboratory Goal: To explore the properties of passive signal-processing filters Learning Objectives: Passive filters, Frequency domain, Bode plots
More informationDesigning Information Devices and Systems II Fall 2018 Elad Alon and Miki Lustig Homework 4
EECS 6B Designing Information Devices and Systems II Fall 208 Elad Alon and Miki Lustig Homework 4 This homework is solely for your own practice. However, everything on it is in scope for midterm, and
More information3. Voltage and Current laws
1 3. Voltage and Current laws 3.1 Node, Branches, and loops A branch represents a single element such as a voltage source or a resistor A node is the point of the connection between two or more elements
More informationLecture Week 5. Voltage Divider Method Equivalent Circuits Review Lab Report Template and Rubric Workshop
Lecture Week 5 Voltage Divider Method Equivalent Circuits Review Lab Report Template and Rubric Workshop Voltage Divider Method The voltage divider is a method/tool that can be used to: Design voltage
More informationCombination Notch and Bandpass Filter
Combination Notch and Bandpass Filter Clever filter design for graphic equalizer can perform both notch and bandpass functions Gain or attenuation is controlled by a potentiometer for specific frequency
More informationBME 3512 Bioelectronics Laboratory Two - Passive Filters
BME 35 Bioelectronics Laboratory Two - Passive Filters Learning Objectives: Understand the basic principles of passive filters. Laboratory Equipment: Agilent Oscilloscope Model 546A Agilent Function Generator
More informationElectronics basics for MEMS and Microsensors course
Electronics basics for course, a.a. 2017/2018, M.Sc. in Electronics Engineering Transfer function 2 X(s) T(s) Y(s) T S = Y s X(s) The transfer function of a linear time-invariant (LTI) system is the function
More informationCHAPTER 14. Introduction to Frequency Selective Circuits
CHAPTER 14 Introduction to Frequency Selective Circuits Frequency-selective circuits Varying source frequency on circuit voltages and currents. The result of this analysis is the frequency response of
More informationEE42: Running Checklist of Electronics Terms Dick White
EE42: Running Checklist of Electronics Terms 14.02.05 Dick White Terms are listed roughly in order of their introduction. Most definitions can be found in your text. Terms2 TERM Charge, current, voltage,
More informationECE 2100 Experiment VI AC Circuits and Filters
ECE 200 Experiment VI AC Circuits and Filters November 207 Introduction What happens when we put a sinusoidal signal through a typical linear circuit? We will get a sinusoidal output of the same frequency,
More informationFrequency Selective Circuits
Lab 15 Frequency Selective Circuits Names Objectives in this lab you will Measure the frequency response of a circuit Determine the Q of a resonant circuit Build a filter and apply it to an audio signal
More informationAdvanced Measurements
Albaha University Faculty of Engineering Mechanical Engineering Department Lecture 9: Wheatstone Bridge and Filters Ossama Abouelatta o_abouelatta@yahoo.com Mechanical Engineering Department Faculty of
More informationThe above figure represents a two stage circuit. Recall, the transfer function relates. Vout
LABORATORY 12: Bode plots/second Order Filters Material covered: Multistage circuits Bode plots Design problem Overview Notes: Two stage circuits: Vin1 H1(s) Vout1 Vin2 H2(s) Vout2 The above figure represents
More informationITT Technical Institute ET245 Devices II Unit 5 Chapter
ITT Technical Institute ET245 Devices II Unit 5 Chapter 7.1 7.3 Unit 5 Agenda Lecture: Chapter 7, Sections 7.1 7.3 Lab 3, Linear Op amp Circuits continued from last week Assignment: Complete Problems (pg
More informationAnalog Filters D R. T A R E K T U T U N J I P H I L A D E L P H I A U N I V E R S I T Y, J O R D A N
Analog Filters D. T A E K T U T U N J I P H I L A D E L P H I A U N I V E S I T Y, J O D A N 2 0 4 Introduction Electrical filters are deigned to eliminate unwanted frequencies Filters can be classified
More informationDifferential Amplifier : input. resistance. Differential amplifiers are widely used in engineering instrumentation
Differential Amplifier : input resistance Differential amplifiers are widely used in engineering instrumentation Differential Amplifier : input resistance v 2 v 1 ir 1 ir 1 2iR 1 R in v 2 i v 1 2R 1 Differential
More informationUNIVERSITY OF NORTH CAROLINA AT CHARLOTTE Department of Electrical and Computer Engineering
UNIVERSITY OF NORTH CAROLINA AT CHARLOTTE Department of Electrical and Computer Engineering EXPERIMENT 8 FILTER NETWORKS OBJECTIVES In this lab session the student will investigate passive low-pass and
More informationInstrumentation Amplifiers Filters Integrators Differentiators Frequency-Gain Relation Non-Linear Op-Amp Applications DC Imperfections
Lecture Op-Amp Building Blocks and Applications Instrumentation Amplifiers Filters Integrators Differentiators Frequency-Gain elation Non-Linear Op-Amp Applications DC Imperfections ELG439 Check List for
More informationAnalog Electronics. Lecture. Op-amp Circuits and Active Filters. Muhammad Amir Yousaf
Analog Electronics Lecture Op-amp Circuits and Active Filters Muhammad Amir Yousaf Instrumentation Amplifiers An instrumentation amplifier (IA) amplifies the voltage difference between its terminals. It
More informationBasic Analog Circuits
Basic Analog Circuits Overview This tutorial is part of the National Instruments Measurement Fundamentals series. Each tutorial in this series, will teach you a specific topic of common measurement applications,
More informationECE215 Lecture 7 Date:
Lecture 7 Date: 29.08.2016 AC Circuits: Impedance and Admittance, Kirchoff s Laws, Phase Shifter, AC bridge Impedance and Admittance we know: we express Ohm s law in phasor form: where Z is a frequency-dependent
More informationMechatronics. Analog and Digital Electronics: Studio Exercises 1 & 2
Mechatronics Analog and Digital Electronics: Studio Exercises 1 & 2 There is an electronics revolution taking place in the industrialized world. Electronics pervades all activities. Perhaps the most important
More information10. Introduction and Chapter Objectives
Real Analog - Circuits Chapter 0: Steady-state Sinusoidal Analysis 0. Introduction and Chapter Objectives We will now study dynamic systems which are subjected to sinusoidal forcing functions. Previously,
More informationHomework Assignment 01
Homework Assignment 01 In this homework set students review some basic circuit analysis techniques, as well as review how to analyze ideal op-amp circuits. Numerical answers must be supplied using engineering
More informationME 365 EXPERIMENT 7 SIGNAL CONDITIONING AND LOADING
ME 365 EXPERIMENT 7 SIGNAL CONDITIONING AND LOADING Objectives: To familiarize the student with the concepts of signal conditioning. At the end of the lab, the student should be able to: Understand the
More informationChapter 2. The Fundamentals of Electronics: A Review
Chapter 2 The Fundamentals of Electronics: A Review Topics Covered 2-1: Gain, Attenuation, and Decibels 2-2: Tuned Circuits 2-3: Filters 2-4: Fourier Theory 2-1: Gain, Attenuation, and Decibels Most circuits
More informationIntroduction... 1 Part I: Getting Started with Circuit Analysis Part II: Applying Analytical Methods for Complex Circuits...
Contents at a Glance Introduction... 1 Part I: Getting Started with Circuit Analysis... 5 Chapter 1: Introducing Circuit Analysis...7 Chapter 2: Clarifying Basic Circuit Concepts and Diagrams...15 Chapter
More informationBME/ISE 3512 Bioelectronics Laboratory Two - Passive Filters
BME/ISE 35 Bioelectronics Laboratory Two - Passive Filters Learning Objectives: Understand the basic principles of passive filters. Supplies and Components: Breadboard 4.7 K Resistor 0.047 F Capacitor
More informationActiveLowPassFilter -- Overview
ActiveLowPassFilter -- Overview OBJECTIVES: At the end of performing this experiment, learners would be able to: Describe the concept of active Low Pass Butterworth Filter Obtain the roll-off factor and
More informationHomework Assignment 01
Homework Assignment 01 In this homework set students review some basic circuit analysis techniques, as well as review how to analyze ideal op-amp circuits. Numerical answers must be supplied using engineering
More informationENGR4300 Test 3A Fall 2002
1. 555 Timer (20 points) Figure 1: 555 Timer Circuit For the 555 timer circuit in Figure 1, find the following values for R1 = 1K, R2 = 2K, C1 = 0.1uF. Show all work. a) (4 points) T1: b) (4 points) T2:
More informationHomework Assignment True or false. For both the inverting and noninverting op-amp configurations, V OS results in
Question 1 (Short Takes), 2 points each. Homework Assignment 02 1. An op-amp has input bias current I B = 1 μa. Make an estimate for the input offset current I OS. Answer. I OS is normally an order of
More informationPhysics 303 Fall Module 4: The Operational Amplifier
Module 4: The Operational Amplifier Operational Amplifiers: General Introduction In the laboratory, analog signals (that is to say continuously variable, not discrete signals) often require amplification.
More informationHomework Assignment 01
Homework Assignment 01 In this homework set students review some basic circuit analysis techniques, as well as review how to analyze ideal op-amp circuits. Numerical answers must be supplied using engineering
More informationECE 3155 Experiment I AC Circuits and Bode Plots Rev. lpt jan 2013
Signature Name (print, please) Lab section # Lab partner s name (if any) Date(s) lab was performed ECE 3155 Experiment I AC Circuits and Bode Plots Rev. lpt jan 2013 In this lab we will demonstrate basic
More informationHomework Assignment 06
Question 1 (2 points each unless noted otherwise) Homework Assignment 06 1. True or false: when transforming a circuit s diagram to a diagram of its small-signal model, we replace dc constant current sources
More informationIdeal Op Amps. The Two Golden Rules for circuits with ideal op-amps*
Ideal Op Amps The Two Golden Rules for circuits with ideal op-amps* No voltage difference between op-amp input terminals No current into op-amp inputs * when used in negative feedback amplifiers 1 Approach
More informationELEN 140 ELECTRICAL CIRCUITS II Winter 2013
ELEN 140 ELECTRICAL CIRCUITS II Winter 2013 Professor: Stephen O Loughlin Prerequisite: ELEN 130 Office: C234B Co-requisite: none Office Ph: (250) 762-5445 ext 4376 Lecture: 3.0 hrs/week Email: soloughlin@okanagan.bc.ca
More informationECE 215 Lecture 8 Date:
ECE 215 Lecture 8 Date: 28.08.2017 Phase Shifter, AC bridge AC Circuits: Steady State Analysis Phase Shifter the circuit current I leads the applied voltage by some phase angle θ, where 0 < θ < 90 ο depending
More informationLab 9 Frequency Domain
Lab 9 Frequency Domain 1 Components Required Resistors Capacitors Function Generator Multimeter Oscilloscope 2 Filter Design Filters are electric components that allow applying different operations to
More informationIntroduction to Signals, Passive RC Filters and Opamps
Introduction to Signals, ive RC Filters and Opamps LB Introduction In this laboratory exercise you design, build and test some simple filter circuits. his is mainly for you to get comfortable with circuit
More informationDesigning Information Devices and Systems II Fall 2017 Miki Lustig and Michel Maharbiz Homework 3
EECS 16B Designing Information Devices and Systems II Fall 2017 Miki Lustig and Michel Maharbiz Homework 3 This homework is due September 19, 2017, at Noon. Please use radians for all angles in phasor
More informationECEN Network Analysis Section 3. Laboratory Manual
ECEN 3714----Network Analysis Section 3 Laboratory Manual LAB 07: Active Low Pass Filter Oklahoma State University School of Electrical and Computer Engineering. Section 3 Laboratory manual - 1 - Spring
More informationOPERATIONAL AMPLIFIERS (OP-AMPS) II
OPERATIONAL AMPLIFIERS (OP-AMPS) II LAB 5 INTRO: INTRODUCTION TO INVERTING AMPLIFIERS AND OTHER OP-AMP CIRCUITS GOALS In this lab, you will characterize the gain and frequency dependence of inverting op-amp
More informationLecture 2 Analog circuits...or How to detect the Alarm beacon
Lecture 2 Analog circuits..or How to detect the Alarm beacon I t IR light generates collector current V1 9V +V I c Q1 OP805 IR detection Vout Noise sources: Electrical (60Hz, 120Hz, 180Hz.) Other electrical
More informationBasics of Analog Multiplexers 1. Exercises TI Precision Labs Op Amps
Basics of Analog Multiplexers 1 Exercises TI Precision Labs Op Amps 1 VSS VDD 1. In the circuit below, one of the input channels of the MUX36S08 is fed with a 2V p-p sinewave signal. The output of the
More informationHomework Assignment 07
Homework Assignment 07 Question 1 (Short Takes). 2 points each unless otherwise noted. 1. A single-pole op-amp has an open-loop low-frequency gain of A = 10 5 and an open loop, 3-dB frequency of 4 Hz.
More informationPhy 335, Unit 4 Transistors and transistor circuits (part one)
Mini-lecture topics (multiple lectures): Phy 335, Unit 4 Transistors and transistor circuits (part one) p-n junctions re-visited How does a bipolar transistor works; analogy with a valve Basic circuit
More informationThird Year (Electrical & Telecommunication Engineering)
Z PRACTICAL WORK BOOK For The Course EE-315 Electric Filter For Third Year (Electrical & Telecommunication Engineering) Name of Student: Class: Batch : Discipline: Class Roll No.: Examination Seat No.
More informationLecture 2 Analog circuits. Seeing the light..
Lecture 2 Analog circuits Seeing the light.. I t IR light V1 9V +V Q1 OP805 RL IR detection Vout Noise sources: Electrical (60Hz, 120Hz, 180Hz.) Other electrical IR from lights IR from cameras (autofocus)
More informationv(t) = V p sin(2π ft +φ) = V p cos(2π ft +φ + π 2 )
1 Let us revisit sine and cosine waves. A sine wave can be completely defined with three parameters Vp, the peak voltage (or amplitude), its frequency w in radians/second or f in cycles/second (Hz), and
More informationLaboratory 4 Operational Amplifier Department of Mechanical and Aerospace Engineering University of California, San Diego MAE170
Laboratory 4 Operational Amplifier Department of Mechanical and Aerospace Engineering University of California, San Diego MAE170 Megan Ong Diana Wu Wong B01 Tuesday 11am April 28 st, 2015 Abstract: The
More informationCHAPTER 9. Sinusoidal Steady-State Analysis
CHAPTER 9 Sinusoidal Steady-State Analysis 9.1 The Sinusoidal Source A sinusoidal voltage source (independent or dependent) produces a voltage that varies sinusoidally with time. A sinusoidal current source
More informationEE233 Autumn 2016 Electrical Engineering University of Washington. EE233 HW7 Solution. Nov. 16 th. Due Date: Nov. 23 rd
EE233 HW7 Solution Nov. 16 th Due Date: Nov. 23 rd 1. Use a 500nF capacitor to design a low pass passive filter with a cutoff frequency of 50 krad/s. (a) Specify the cutoff frequency in hertz. fc c 50000
More informationECE 317 Laboratory #1 Force Sensitive Resistors
ECE 317 Laboratory #1 Force Sensitive Resistors Background Force, pressure, and position sensing are required for a wide variety of uses. In this lab, we will investigate a sensor called a force sensitive
More informationBIOE 123 Module 3. Electronics 2: Time Varying Circuits. Lecture (30 min) Date. Learning Goals
BIOE 123 Module 3 Electronics 2: Time Varying Circuits Lecture (30 min) Date Learning Goals Learn about the behavior of capacitors and inductors Learn how to analyze time-varying circuits to quantify parameters
More informationCMOS Operational-Amplifier
CMOS Operational-Amplifier 1 What will we learn in this course How to design a good OP Amp. Basic building blocks Biasing and Loading Swings and Bandwidth CH2(8) Operational Amplifier as A Black Box Copyright
More informationBME 3512 Bioelectronics Laboratory Six - Active Filters
BME 5 Bioelectronics Laboratory Six - Active Filters Learning Objectives: Understand the basic principles of active filters. Describe the differences between active and passive filters. Laboratory Equipment:
More informationSTATION NUMBER: LAB SECTION: Filters. LAB 6: Filters ELECTRICAL ENGINEERING 43/100 INTRODUCTION TO MICROELECTRONIC CIRCUITS
Lab 6: Filters YOUR EE43/100 NAME: Spring 2013 YOUR PARTNER S NAME: YOUR SID: YOUR PARTNER S SID: STATION NUMBER: LAB SECTION: Filters LAB 6: Filters Pre- Lab GSI Sign- Off: Pre- Lab: /40 Lab: /60 Total:
More informationEE 2274 RC and Op Amp Circuit Completed Prior to Coming to Lab. Prelab Part I: RC Circuit
EE 2274 RC and Op Amp Circuit Completed Prior to Coming to Lab Prelab Part I: RC Circuit 1. Design a high pass filter (Fig. 1) which has a break point f b = 1 khz at 3dB below the midband level (the -3dB
More informationSignal Conditioning Devices
Lecture 4. Signal Conditioning Devices Signal Conditioning Operations In previous lectures we have studied various sensors and transducers used in a mechatronics system. Transducers sense physical phenomenon
More informationLab 10: Oscillators (version 1.1)
Lab 10: Oscillators (version 1.1) WARNING: Use electrical test equipment with care! Always double-check connections before applying power. Look for short circuits, which can quickly destroy expensive equipment.
More informationPoles and Zeros of H(s), Analog Computers and Active Filters
Poles and Zeros of H(s), Analog Computers and Active Filters Physics116A, Draft10/28/09 D. Pellett LRC Filter Poles and Zeros Pole structure same for all three functions (two poles) HR has two poles and
More informationSolution: Based on the slope of q(t): 20 A for 0 t 1 s dt = 0 for 3 t 4 s. 20 A for 4 t 5 s 0 for t 5 s 20 C. t (s) 20 C. i (A) Fig. P1.
Problem 1.24 The plot in Fig. P1.24 displays the cumulative charge q(t) that has entered a certain device up to time t. Sketch a plot of the corresponding current i(t). q 20 C 0 1 2 3 4 5 t (s) 20 C Figure
More informationDOING PHYSICS WITH MATLAB FILTER CIRCUITS
DOING PHYSICS WITH MATLAB FILTER CIRCUITS Matlab download directory Matlab scripts CacFilters1.m Modelling a simple RC low pass filter or RC high pass filter using complex functions to represent circuit
More informationHomework Assignment 03 Solution
Homework Assignment 03 Solution Question 1 Determine the h 11 and h 21 parameters for the circuit. Be sure to supply the units and proper sign for each parameter. (8 points) Solution Setting v 2 = 0 h
More informationEELE 201 Circuits I. Fall 2013 (4 Credits)
EELE 201 Circuits I Instructor: Fall 2013 (4 Credits) Jim Becker 535 Cobleigh Hall 994-5988 Office hours: Monday 2:30-3:30 pm and Wednesday 3:30-4:30 pm or by appointment EMAIL: For EELE 201-related questions,
More informationLecture 8 Amplifiers (Basics)
Lecture 8 Amplifiers (Basics) EE 101 Schedule Version 10-10-11 (supersedes version of 11-5-11 -- date mistake) Class Lecture Date Topic Reading Ahead Homework Quiz 1 1 9-23-11 Introduction Review Math
More informationExercise 1: Series RLC Circuits
RLC Circuits AC 2 Fundamentals Exercise 1: Series RLC Circuits EXERCISE OBJECTIVE When you have completed this exercise, you will be able to analyze series RLC circuits by using calculations and measurements.
More informationLecture # 4 Network Analysis
CPEN 206 Linear Circuits Lecture # 4 Network Analysis Dr. Godfrey A. Mills Email: gmills@ug.edu.gh Phone: 026-907-3163 February 22, 2016 Course TA David S. Tamakloe 1 What is Network Technique o Network
More informationOperational Amplifiers
Operational Amplifiers Continuing the discussion of Op Amps, the next step is filters. There are many different types of filters, including low pass, high pass and band pass. We will discuss each of the
More informationLaboratory 2 (drawn from lab text by Alciatore)
Laboratory 2 (drawn from lab text by Alciatore) Instrument Familiarization and Basic Electrical Relations Required Components: 2 1k resistors 2 1M resistors 1 2k resistor Objectives This exercise is designed
More informationHomework Assignment 06
Homework Assignment 06 Question 1 (Short Takes) One point each unless otherwise indicated. 1. Consider the current mirror below, and neglect base currents. What is? Answer: 2. In the current mirrors below,
More informationSyllabus for ENGR065-01: Circuit Theory
Syllabus for ENGR065-01: Circuit Theory Fall 2017 Instructor: Huifang Dou Designation: Catalog Description: Text Books and Other Required Materials: Course Objectives Student Learning Outcomes: Course
More informationTransmit filter designs for ADSL modems
EE 233 Laboratory-4 1. Objectives Transmit filter designs for ADSL modems Design a filter from a given topology and specifications. Analyze the characteristics of the designed filter. Use SPICE to verify
More informationEE 221 L CIRCUIT II. by Ming Zhu
EE 22 L CIRCUIT II LABORATORY 9: RC CIRCUITS, FREQUENCY RESPONSE & FILTER DESIGNS by Ming Zhu DEPARTMENT OF ELECTRICAL AND COMPUTER ENGINEERING UNIVERSITY OF NEVADA, LAS VEGAS OBJECTIVE Enhance the knowledge
More informationELECTRICAL CIRCUITS 6. OPERATIONAL AMPLIFIERS PART III DYNAMIC RESPONSE
77 ELECTRICAL CIRCUITS 6. PERATAL AMPLIIERS PART III DYNAMIC RESPNSE Introduction In the first 2 handouts on op-amps the focus was on DC for the ideal and non-ideal opamp. The perfect op-amp assumptions
More informationOPERATIONAL AMPLIFIERS and FEEDBACK
Lab Notes A. La Rosa OPERATIONAL AMPLIFIERS and FEEDBACK 1. THE ROLE OF OPERATIONAL AMPLIFIERS A typical digital data acquisition system uses a transducer (sensor) to convert a physical property measurement
More informationEXPERIMENT 4: RC, RL and RD CIRCUITs
EXPERIMENT 4: RC, RL and RD CIRCUITs Equipment List Resistor, one each of o 330 o 1k o 1.5k o 10k o 100k o 1000k 0.F Ceramic Capacitor 4700H Inductor LED and 1N4004 Diode. Introduction We have studied
More informationRLC Frequency Response
1. Introduction RLC Frequency Response The student will analyze the frequency response of an RLC circuit excited by a sinusoid. Amplitude and phase shift of circuit components will be analyzed at different
More information