OPERATING MANUAL VOLTAGE CONTROLLED OSCILLATOR MODEL NUMBER: 21XXX-YYY-ZASVCO DOCUMENT NUMBER: 51A18410
|
|
|
- Alexia Lewis
- 5 years ago
- Views:
Transcription
1 OPERATING MANUAL VOLTAGE CONTROLLED OSCILLATOR MODEL NUMBER: 21XXX-YYY-ZASVCO DOCUMENT NUMBER: 51A18410 This Operating Manual is for use with Variable Frequency AOM Drivers with model numbers: XXX = The Lower frequency of between 27 and 200 MHz YYY = The Higher frequency of between 27 and 200 MHz Z = 1 or 2 Watts output power S =Rack Mountable System Box Voltage Controlled Oscillator A = Analog Modulation Document approved for release: W Seale Date: 11/07/05 US OFFICE: Opportunity Drive Melbourne, FL USA Tel: (321) Fax: (321) neos@neostech.com UK OFFICE: Gooch & Housego The Old Magistrates Court Ilminster, Somerset TA19 0AB UK Tel: Fax: sales@goochandhousego.com
2 TABLE OF CONTENTS Section Title Page I INSPECTION PROCEDURE 3 II GENERAL DESCRIPTION 4 III SPECIFICATION 5 IV OUTLINE DRAWING 6 V CONTROLS AND CONNECTIONS 7 VI OPERATING PROCEDURE 8 51A18410.doc Approved for release W. Seale 11/ 07/05 2 OF 8
3 SECTION I INSPECTION Examine the shipping carton for damage. If the shipping carton or packing material is damaged it should be kept for the carrier s inspection. Check the contents of the shipment for completeness, mechanical damage, and then test the equipment electronically. Operating procedures are contained in Section VI. Notify the carrier and NEOS Technologies. If the contents are incomplete, or the equipment does not pass the electrical testing please notify NEOS Technologies. If there is any problem with the use of this equipment, or if the equipment fails to function as expected contact NEOS Technologies, do not try to trouble shoot or repair this equipment. Consult with a NEOS service engineer. If the equipment needs repair or replacement, contact for a Return Authorization Number. 51A18410.doc Approved for release W. Seale 11/ 07/05 3 OF 8
4 SECTION II GENERAL DESCRIPTION The 21XXX-YYY-ZASVCO is a Voltage Controlled Oscillator in a rack mountable system box. It is designed to supply an RF output of up to 2 Watts of RF energy into an Acousto-Optic Beam Deflector or a 50 Ohm load. The system requires 100 to 240 Volts AC power input, an analog modulation voltage (0 to 1 VDC), and a frequency control voltage (2 to 15 VDC typical) for operation (See the driver ATR for exact data for frequency vs. control voltage). 21XXX-YYY-ZASVCO 53D A18410.doc Approved for release W. Seale 11/ 07/05 4 OF 8
5 SPECIFICATION Output Frequency: Spurious Levels: Harmonic Distortion: Frequency Control Voltage: Analog Input: Extinction Ratio: RF Rise / Fall Time RF Output Power: Output Power Flatness: Output Impedance: Power Input: MAXIMUM RATINGS: Supply Voltage: Power Output: Case Temperature: CONNECTORS & MECHANICAL: RF Output Connector: Modulation Input Connector: Frequency Control Connection: Power Supply Connections: RELATED DOCUMENTS: Outline Drawing: 53D1702 SECTION III. SPECIFICATION PARAMETER XXX to YYY MHz Where XXX to YYY typically is less than an Octave bandwidth, with frequencies from 35 to 200 MHz. -45 dbc Maximum -15 dbc Maximum 2 to 15 Volts Typical + 1 Volt into 50 Ohms, 0 Volts = minimum RF output 1 Volt = maximum RF output 30 db Minimum 20 ns Typically, 30 ns Maximum P RF : 10 to 90 % Z Watts - 1 TO 2 Watts Nominal - Adjustable Factory set for optimum performance when paired with a NEOS AO Device. 1.5 db Maximum 50 Ohms Nominal 90 to / 60 Hz 1.5 Amps 264 VAC No DC Feedback Allowed C. 3 pin IEC panel mount EMI Filtered. 51A18410.doc Approved for release W. Seale 11/ 07/05 5 OF 8
6 SECTION IV OUTLINE DRAWING A18410.doc Approved for release W. Seale 11/ 07/05 6 OF 8
7 SECTION V CONTROLS AND CONNECTIONS BACK PANEL: A C B A. RF OUT - The output of the driver supplies 1 or 2 Watts of RF energy into the Acousto-Optical Beam Deflector or a 50 Ohm load. B. FREQUENCY This port accepts a control voltage between +2 and +15 CONTROL Volts. The exact control voltage vs. frequency data is supplied VOLTAGE - with the acceptance test results for each driver. C. MODULATION This port accepts an analog modulation voltage between INPUT - "0" and +1Volt. +1 Volt is full on. FRONT PANEL: D E D. POWER SWITCH Applies AC power to the system. E. NORMAL/CW CW Position: The RF output power is set to full on. MODE SWITCH NORMAL Position: The output power follows the mod in voltage. 51A18410.doc Approved for release W. Seale 11/ 07/05 7 OF 8
8 SECTION VI OPERATING PROCEDURES TESTING: Connect the "RF out" to a 50 Ohm load capable of dissipating 2 Watts. Connect a VCO control Voltage to the "CONTROL VOLTAGE" (SMB connector). See the driver ATR for voltage vs. frequency data. Connect a 0-1 DC Voltage for amplitude control to the "MOD IN" (BNC connector) (1VDC = full on). DO NOT EXCEED 1VDC. Turn on the Power Switch. With the Mode switch in the NORMAL position, and with 1 Volt applied to the "MOD IN" input, adjust the control voltage to the low, center, and high frequency as required to test the driver. See the driver ATR for Voltage vs. frequency data. Or, if a sweep generator is available, sweep the control voltage from the low to high voltage as listed on the ATR. Measure each of the parameters as listed on the driver ATR. With 1 Volt on the MOD IN, adjust, if necessary, the driver output power level control (white one turn pot on pc board inside the driver box) for the power required for maximum diffraction efficiency of the AO devices or to a power which does not exceed the maximum allowed for the AO devices. Do not exceed the maximum allowed for the AO devices or damage will occur. If damage results due to overpowering the AO device, the warranty will be void. OPERATION: Attach the AO device to the RF output with a 50 Ohm cable. Follow the instructions in the AOBD device manual to align and adjust the devices as required in the laser beam of your optical system. Apply the necessary signals to the frequency and amplitude control as desired. 51A18410.doc Approved for release W. Seale 11/ 07/05 8 OF 8
OPERATING MANUAL VOLTAGE CONTROLLED OSCILLATOR MODEL NUMBER: 21XXX-YYY-ZAMVCO DOCUMENT NUMBER: 51A18412A
OPERATING MANUAL VOLTAGE CONTROLLED OSCILLATOR MODEL NUMBER: 21XXX-YYY-ZAMVCO DOCUMENT NUMBER: 51A18412A This Operating Manual is for use with Variable Frequency AOM Drivers with model numbers: XXX = The
Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment
Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment FAST SHIPPING AND DELIVERY TENS OF THOUSANDS OF IN-STOCK ITEMS EQUIPMENT DEMOS HUNDREDS OF MANUFACTURERS SUPPORTED
OPERATING MANUAL DIGITALLY CONTROLLED FREQUENCY SYNTHESIZED OSCILLATOR MODEL NUMBER: ADSDFS-A DOCUMENT NUMBER: 51A19937C
OPERATING MANUAL DIGITALLY CONTROLLED FREQUENCY SYNTHESIZED OSCILLATOR MODEL NUMBER: DOCUMENT NUMBER: 51A19937C For More Information, Contact: sales@goochandhousego.com www.goochandhousego.com As part
OPERATING MANUAL CAVITY DUMPER / PULSE PICKER DRIVER MODEL NUMBER: 643ZZ.ZZZ-SYN-Y-X
OPERATING MANUAL CAVITY DUMPER / PULSE PICKER DRIVER MODEL NUMBER: Where: X is the division factors for the pulse rate. Y is the multiplier of the reference input frequency 3ZZ.ZZZ is the output RF frequency
OPERATING MANUAL. 100 MHz CENTER FREQUENCY OFF AXIS ACOUSTO-OPTIC BEAM DEFLECTOR MODEL NUMBER: DEG-.51 DOCUMENT NUMBER: 51A12229A
OPERATING MANUAL 100 MHz CENTER FREQUENCY OFF AXIS ACOUSTO-OPTIC BEAM DEFLECTOR MODEL NUMBER: DOCUMENT NUMBER: 51A12229A Document approved for release: W Seale Date: 8/18/06 US OFFICE: NEOS Technologies,
OPERATING MANUAL. ACOUSTO OPTIC MODULATOR MODEL NUMBER: X-LTD X= 1, 2, or 3 mm DOCUMENT NUMBER: 51A00620D
OPERATING MANUAL ACOUSTO OPTIC MODULATOR MODEL NUMBER: 23080-1 23080-X-LTD X= 1, 2, or 3 mm DOCUMENT NUMBER: 51A00620D Document approved for release: W Seale Date: 6/20/06 US OFFICE:. 4005 Opportunity
OPERATING MANUAL. ACOUSTO OPTIC MODULATOR MODEL NUMBER: X-1.06-LTD X= 1, 2, or 3 mm DOCUMENT NUMBER: 51A14950A
OPERATING MANUAL ACOUSTO OPTIC MODULATOR MODEL NUMBER: X= 1, 2, or 3 mm DOCUMENT NUMBER: 51A14950A Document approved for release: W Seale Date: 6/06/06 US OFFICE: NEOS Technologies, Inc. 4005 Opportunity
MQH0XX-YYDS3-ZZZ-2S. High Power 2 Channel RF Driver: For 2 Acousto-optic Q-Switches. Description: Key Features: Applications:
High Power 2 Channel RF Driver: For 2 Acousto-optic Q-Switches MQH0XX-YYDS3-ZZZ-2S Former Model Number: 390XX-YYDSZZZ-2CH-A Description: The MQH0XX-YYDS3-ZZZ-2S is a High Power RF Driver with two RF outputs
Base model features 1.0Vpp, 50ohm modulation input level and 24/28Vdc supply. L : +15V supply operation
ISOMET Acousto-Optic Deflector Driver Including: Basic Deflector Alignment Instruction Manual 620c Series Digital Modulation Key to model types : 620C-fff-m Base model features 1.0Vpp, 50ohm modulation
Base model features 1.0Vpp, 50ohm modulation input level and 24/28Vdc supply.
2016-11 ISOMET Acousto-Optic Deflector Driver Including: Basic Deflector Alignment Instruction Manual 630c Series Analog Modulation Key to model types : 630C-fff-m Base model features 1.0Vpp, 50ohm modulation
Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment
Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment FAST SHIPPING AND DELIVERY TENS OF THOUSANDS OF IN-STOCK ITEMS EQUIPMENT DEMOS HUNDREDS OF MANUFACTURERS SUPPORTED
AOM Driver A35-Series
AOM Driver A35-Series 5 Watt RF Drivers for Acousto-Optic Modulators The A35xxx RF driver series provides up to 5 Watt output power. Various types cover a frequency range from 40 to 350 MHz. The maximum
ISOMET. Acousto-Optic Deflector Driver. Instruction Manual. D3x5-BS Series. Including: Basic Deflector Alignment. Models -
Acousto-Optic Deflector Driver Including: Basic Deflector Alignment Instruction Manual D3x5-BS Series Models - D325-BS D335-BS : 10V Tuning Input, TTL Digital Modulation Input : 10V Tuning Input, 1.0V
ISOMET. Acousto-Optic Modulator Driver. Instruction Manual. 512c-m Series. Including: Basic Modulator Alignment
Acousto-Optic Modulator Driver Including: Basic Modulator Alignment Instruction Manual 512c-m Series Voltage Controlled Crystal Oscillator (VCXO) Driver with Analog Modulation and BIAS, m indicates options
Sintec Optronics Technology Pte Ltd 10 Bukit Batok Crescent #07-02 The Spire Singapore Tel: Fax:
Sintec Optronics Technology Pte Ltd 10 Bukit Batok Crescent #07-02 The Spire Singapore 658079 Tel: +65 63167112 Fax: +65 63167113 Acousto Optical Deflectors An AO Deflector is a device that will scan an
Base model features TTL buffer compatible modulation input level and 24/28Vdc supply.
Acousto-Optic Modulator Driver Including: Basic Modulator Alignment Instruction Manual 750c Series Analog and Digital Dual Modulation Key to model types : 75o.C-m-ff Base model features TTL buffer compatible
Including: Amplifier Connection & AO Deflector Alignment. 630C-fff-LP-m. Base model features 1.0Vpp, 50ohm modulation input level and 24/28Vdc supply.
2015-12 ISOMET VCO Tuneable Frequency Source Including: Amplifier Connection & AO Deflector Alignment Instruction Manual 630c--LP Series Analog Modulation Key to model types : 630C-fff-LP-m Base model
ISOMET. Acousto-Optic Modulator Driver. Instruction Manual. RFA9x0-41 Series. Including: Basic Modulator/Q-switch Alignment. May 07.
May 07 ISOMET Acousto-Optic Modulator Driver Including: Basic Modulator/Q-switch Alignment Instruction Manual RFA9x0-41 Series Models - RFA910x-41 RFA920x-41 RFA960x-41 : 40.68MHz, >10W output : 40.68MHz,
AOM Driver 2910 Series
AOM Driver 2910 Series 1 to 4 Watt RF Drivers for Acousto-Optic Modulators The 2910 Series RF driver provides up to 4 Watts output power. Various types cover a frequency range of 80 to 350 MHz. The maximum
Precautions NEVER OPERATE THE DRIVER WITHOUT PROPER COOLING. THE MOUNTING FACE TEMPERATURE MUST NOT EXCEED 60*C.
Dual Channel AMPLIFIER Instruction Manual DA104-2 Precautions NEVER OPERATE THE DRIVER WITHOUT PROPER COOLING. THE MOUNTING FACE TEMPERATURE MUST NOT EXCEED 60*C. NEVER OPERATE THE DRIVER INTO AN OPEN
AOM Driver 3307 Series
AOM Driver 3307 Series 1 to 4 Watt RF Drivers for Acousto-Optic Modulators The 3307 Series RF driver provides up to 4 Watts output power. Various types cover a frequency range of 80 to 350 MHz. The maximum
Model Number Guide. M= Material. S= Apperture Size. P= Options
Model Number Guide Brimrose Corporation of America manufactures both standard (from the specification sheet) and custom (to customer specifications) Acousto-Optic Tunable Filters. The following Model Number
Recirculating Loop System (No Frequency Shift) AMM C-RLS(nfs)-RM
Recirculating Loop System (No Frequency Shift) AMM-100-8-70-C-RLS(nfs)-RM KEY FEATURES R F D R I V E R R E C I R C U L A T I N G L O O P S Y S T E M D I A G R A M Low Insertion Loss No O-rings Rack-mount
Installation & Service Manual
869-894 MHz Installation & Service Manual Model SCA 9321-30C Single-Channel Cellular Amplifier 044-xxxxx Rev.A February 2003 2003 Powerwave Technologies Incorporated. All rights reserved. Powerwave Technologies,
ISOMET. Acousto-Optic Deflector Amplifier. Instruction Manual. RFA100 Series. Including: Basic Modulator Alignment. Apr 13.
Apr 13 Acousto-Optic Deflector Amplifier Including: Basic Modulator Alignment Instruction Manual RFA100 Series Models - RFA100-x : 30-50MHz, 25W output Options -x: - L : active low digital modulation (gate)
ISOMET. Acousto-Optic Modulator Driver. Instruction Manual. RFA141 Series & RFA151 Series. Including: Basic Modulator Alignment for 1202 / 1208 series
Jan 0 ISOMET Acousto-Optic Modulator Driver Including: Basic Modulator Alignment for 202 / 208 series Instruction Manual RFA4 Series & RFA5 Series Models - RFA4-x RFA5-x : 40MHz, >30W output : 50MHz, >40W
Model Hz to 10MHz Precision Phasemeter. Operating Manual
Model 6610 1Hz to 10MHz Precision Phasemeter Operating Manual Service and Warranty Krohn-Hite Instruments are designed and manufactured in accordance with sound engineering practices and should give long
Where λ is the optical wavelength in air, V a is the acoustic velocity, and f is the frequency bandwidth. Incident Beam
Introduction to A-O Deflectors/Scanners An acoustic deflector/scanner changes the angle of direction of a laser beam and its angular position is linearly proportional to the acoustic frequency, so that
411LA Broadband Power Amplifier
411LA Broadband Power Amplifier HIGH RF VOLTAGES MAY BE PRESENT AT THE OUTPUT OF THIS UNIT. All operating personnel should use extreme caution in handling these voltages and be thoroughly familiar with
MT80-A1-VIS/IR/1064, MT80-A1.5-VIS/IR/1064 MT110-A1-VIS/IR/1064, MT110-A1.5-VIS/IR/1064
MT-A-VIS/IR/64, MT-A.5-VIS/IR/64 MT-A-VIS/IR/64, MT-A.5-VIS/IR/64 AO MODULATOR/SHIFTER Product Overview These free space modulators are proposed with different aperture sizes and at various wavelength
Broadband Power Amplifier
601L Broadband Power Amplifier HIGH RF VOLTAGES MAY BE PRESENT AT THE OUTPUT OF THIS UNIT. All operating personnel should use extreme caution in handling these voltages and be thoroughly familiar with
INSTRUCTION MANUAL. Acousto-OptIc Modulator/Drfver Series 230. (Analog Modulation) ***PRECAUTIONS***
Series 230 May 1993 ISOMET INSTRUCTION MANUAL Acousto-OptIc Modulator/Drfver Series 230 (Analog Modulation) ***PRECAUTIONS*** Never operate the driver without proper cooling. The mounting face temperature
Model 25A Manual. Introduction:
Model 25A Manual Introduction: The Model 25A drive electronics is a high voltage push-pull linear power amplifier capable of output voltage swings in the order of 145v P-P, push-pull. The Model 25A provides
MT80-A1-VIS/IR/1064, MT80-A1.5-VIS/IR/1064 MT110-A1-VIS/IR/1064, MT110-A1.5-VIS/IR
MT-A-VIS/IR/64, MT-A.5-VIS/IR/64 MT-A-VIS/IR/64, MT-A.5-VIS/IR AO MODULATOR/SHIFTER Product Overview These free space modulators are proposed with different aperture sizes and at various wavelength ranges.
Fiber Pigtailed Variable Frequency Shifters Acousto-optic products
Fiber Pigtailed Variable Frequency Shifters Acousto-optic products Introduction Frequency Shift LASER DOPPLER VIBROMETER (LDV) 3- PHYSICAL PRINCIPLES MAIN EQUATIONS An RF signal applied to a piezo-electric
MT80-A TECHNICAL DATA SHEET 2014
MT8-A.7-3.6 AO MODULATOR/SHIFTER Product Overview These free space modulators has been specially designed for general purpose high speed applications. They are dedicated to IR lasers such as 3, 5 nm. Their
SDI SPECTRADYNAMICS, INC. LOW NOISE FREQUENCY REFERENCE OPERATING MANUAL
SPECTRADYNAMICS, INC. LOW NOISE FREQUENCY REFERENCE LNFR-100E OPERATING MANUAL SPECTRADYNAMICS, INC 1849 Cherry St. Unit 2. Louisville, CO 80027 Phone: (303) 665-1852 Fax: (303) 604-6088 www.spectradynamics.com
ISOMET. Acousto-Optic Modulator Driver. Instruction Manual. RFA2x1 Series. Including: Basic Modulator Alignment. Feb 17. Models - RFA2x1-z :
Feb 17 ISOMET Acousto-Optic Modulator Driver Including: Basic Modulator Alignment Instruction Manual RFA2x1 Series Models - RFA2x1-z : x = 5 : x = 6 : x = 7 : x = 8 : Fc = 50MHz Fc = 60MHz Fc = 70MHz Fc
CBA 400M MHZ to 400 MHZ
1 CBA 400M-100 1 MHZ to 400 MHZ 100 watt amplifier user Manual 601-298A CBA 400M-100 1 MHZ to 400 MHZ 100 watt amplifier USER Manual CBA 400M-100 User Manual contents 1 Safety information 5 2 Introduction
- BR : Brass heatsink, rear mounted water fittings only. (to suit brass or copper cased AO devices)
Oct 14 ISOMET Acousto-Optic Modulator Driver Including: Basic Modulator Alignment Instruction Manual RFA141, RFA151, RFA181 Series Models - RFA141-x RFA151-x RFA181-x : 40MHz, >30W output : 50MHz, >40W
HESP-E-AO-PS Laboratory Diode Driver (For use with Kigre AO-1010 and AO-610 lasers)
HESP-E-AO-PS Laboratory Diode Driver (For use with Kigre AO-1010 and AO-610 lasers) Kigre manufactures a laboratory laser diode driver for use with the AO-1010 and AO-610 actively Q-switched laser heads.
LPF-100 Composite Low Pass Filter
Broadcast Devices, Inc. LPF-00 Composite Low Pass Filter TECHNICAL REFERENCE MANUAL Broadcast Devices, Inc. 0 E. Main Street Cortlandt Manor, NY 07 Tel. (94) 77-0 Fax. (94) 7-9 REV: A 0/09 Table of Contents
2100L Broadband Power Amplifier
2100L Broadband Power Amplifier HIGH RF VOLTAGES MAY BE PRESENT AT THE OUTPUT OF THIS UNIT. All operating personnel should use extreme caution in handling these voltages and be thoroughly familiar with
GPS10RBN-26: 10 MHz, GPS Disciplined, Ultra Low Noise Rubidium Frequency Standard
GPS10RBN-26: 10 MHz, GPS Disciplined, Ultra Low Noise Rubidium Standard Key Features Completely self-contained unit. No extra P.C needed. Full information available via LCD. Rubidium Oscillator locked
MT110-B50A1.5-IR-Hk + MDPS1C-xx
MT110-B50A1.5-IR-Hk + MDPS1C-xx IR TUNABLE AO MODULATOR SYSTEM Description This complete system has been specially designed for tuneable Ti:Sa. It consists of having a modulator in association with a MPDS
1140LA Broadband Power Amplifier
1140LA Broadband Power Amplifier HIGH RF VOLTAGES MAY BE PRESENT AT THE OUTPUT OF THIS UNIT. All operating personnel should use extreme caution in handling these voltages and be thoroughly familiar with
A 500 Broadband Power Amplifier
A 500 Broadband Power Amplifier HIGH RF VOLTAGES MAY BE PRESENT AT THE OUTPUT OF THIS UNIT. All operating personnel should use extreme caution in handling these voltages and be thoroughly familiar with
TIA-525 Optical/Electrical Converter Operating Instructions
TIA-525 Optical/Electrical Converter Operating Instructions Contents Introduction... 1 Specifications... 2 Unpacking and Inspection... 3 Battery Replacement... 3 Controls... 4 Operating Considerations...
Agilent 8657A/8657B Signal Generators
Agilent / Signal Generators Profile Spectral performance for general-purpose test Overview The Agilent Technologies and signal generators are designed to test AM, FM, and pulsed receivers as well as components.
Model 7000 Low Noise Differential Preamplifier
Model 7000 Low Noise Differential Preamplifier Operating Manual Service and Warranty Krohn-Hite Instruments are designed and manufactured in accordance with sound engineering practices and should give
Model 4007DDS. 7 MHz Sweep Function Generator
Model 4007DDS 7 MHz Sweep Function Generator 1 Model 4007DDS - Instruction Manual Limited Two-Year Warranty B&K Precision warrants to the original purchaser that its products and the component parts thereof,
Model Operating Manual
Model 7500 DC to 1MHz Wideband Power Amplifier Operating Manual Copyright 2004. All rights reserved. Contents of this publication may not be reproduced in any form without the written permission of Krohn-Hite
3100LA Broadband Power Amplifier
3100LA Broadband Power Amplifier HIGH RF VOLTAGES MAY BE PRESENT AT THE OUTPUT OF THIS UNIT. All operating personnel should use extreme caution in handling these voltages and be thoroughly familiar with
GT-1050A 2 GHz to 50 GHz Microwave Power Amplifier
Established 1981 Advanced Test Equipment Rentals www.atecorp.com 800-404-ATEC (2832) Giga-tronics GT-1050A Microwave Power Amplifier GT-1050A 2 GHz to 50 GHz Microwave Power Amplifier Operation Manual
This provides extremely fast tuning speed limited primarily by the internal impedance of the user-supplied voltage driver.
Hyperabrupt Varactor-Tuned Oscillators Technical Data VTO-9 Series Features 32 to 2.3 GHz Coverage Fast Tuning Fast Setting Time +2 VDC Max Tuning Voltage 1 mw Output Power ±2. db Output Flatness Hermetic
COM-POWER OPERATION MANUAL ACS W
COM-POWER OPERATION MANUAL For the ACS-250-100W 150 khz to 250 MHz 100W Power Amplifier Page 1 of 15 MANUAL_ACS-250-100W Rev. M02.15 Table of Contents Important Safety Precautions.....3 Introduction..5
FS5000 COMSTRON. The Leader In High Speed Frequency Synthesizers. An Ideal Source for: Agile Radar and Radar Simulators.
FS5000 F R E Q U E N C Y S Y N T H E S I Z E R S Ultra-fast Switching < 200 nsec Wide & Narrow Band Exceptionally Clean An Ideal Source for: Agile Radar and Radar Simulators Radar Upgrades Fast Antenna
INSTALLATION MANUAL. CTA-30RK-550 Rack Mount Distribution Amplifier
INSTALLATION MANUAL CTA-30RK-550 Rack Mount Distribution Amplifier 1 PACKAGE CONTENTS This package contains: One CTA-30RK-550 Rack Mount Distribution Amplifier One CTA-30RK-550 instruction manual PRODUCT
CMP-300 Composite Mixer/ Distribution Amplifier
Broadcast Devices, Inc. CMP00 Composite Mixer/ Distribution Amplifier TECHNICAL REFERENCE MANUAL Broadcast Devices, Inc. Crestview Avenue Cortlandt Manor, NY 0 Tel. (9) 0 Fax. (9) 9 REV: A 0/0 Table of
Varactor-Tuned Oscillators. Technical Data. VTO-8000 Series
Varactor-Tuned Oscillators Technical Data VTO-8000 Series Features 600 MHz to 10.5 GHz Coverage Fast Tuning +7 to +13 dbm Output Power ± 1.5 db Output Flatness Hermetic Thin-film Construction Description
Keysight Technologies N9320B RF Spectrum Analyzer
Keysight Technologies N9320B RF Spectrum Analyzer 9 khz to 3.0 GHz Data Sheet Definitions and Conditions The spectrum analyzer will meet its specifications when: It is within its calibration cycle It has
CALIBRATED IMPULSE GENERATOR MODEL CIG khz 1 GHz
INSTRUCTION MANUAL CALIBRATED IMPULSE GENERATOR MODEL CIG-25 10 khz 1 GHz INSTRUCTION MANUAL THIS INSTRUCTION MANUAL AND ITS ASSOCIATED INFORMATION IS PROPRIETARY. UNAUTHORIZED REPRODUCTION IS FORBIDDEN.
Agilent N9320B RF Spectrum Analyzer
Agilent N9320B RF Spectrum Analyzer 9 khz to 3.0 GHz Data Sheet Definitions and Conditions The spectrum analyzer will meet its specifications when: It is within its calibration cycle It has been turned
Multi-Function Assemblies
K&L Microwave offers a variety of (MFA) products to satisfy a broad range of filtering applications. Many applications require frequency pre-selection at the front end of the communication or test and
Measure the roll-off frequency of an acousto-optic modulator
Slide 1 Goals of the Lab: Get to know some of the properties of pin photodiodes Measure the roll-off frequency of an acousto-optic modulator Measure the cut-off frequency of a pin photodiode as a function
MODEL 3810/2 Line Impedance Stabilization Network
EMC TEST SYSTEMS FEBRUARY 1996 REV C PN 399197 MODEL 3810/2 Line Impedance Stabilization Network OPERATION MANUAL USA P.O. Box 80589 Austin, Texas 78708-0589 2205 Kramer Lane, Austin, Texas 78758-4047
Glossary of VCO terms
Glossary of VCO terms VOLTAGE CONTROLLED OSCILLATOR (VCO): This is an oscillator designed so the output frequency can be changed by applying a voltage to its control port or tuning port. FREQUENCY TUNING
Model 1791 VHF Radio User's Manual
Model 79 VHF Radio User's Manual ALL WEATHER INC 65 NATIONAL DRIVE SACRAMENTO, CA 95834 WWW.ALWEATHERINC.COM 79 VHF RADIO USER'S MANUAL CONTENTS INTRODUCTION... Description... Transmitter Module... Power
PULSE DISTRIBUTION AMPLIFIER OPERATING MANUAL
SPECTRADYNAMICS, INC PD5-RM-B PULSE DISTRIBUTION AMPLIFIER OPERATING MANUAL SPECTRADYNAMICS, INC 1849 Cherry St. Unit 2. Louisville, CO 80027 Phone: (303) 665-1852 Fax: (303) 604-6088 www.spectradynamics.com
150W1000B. Features. 150 watts CW 80MHz 1000MHz Class A Portable Full VSWR tolerant CE & RoHS Compliant High Efficiency
Power (Watts) Specifications Class A Portable Full VSWR tolerant CE & RoHS Compliant High Efficiency Features The Model is a solid-state, selfcontained, air-cooled, broadband amplifier designed for applications
INSTRUCTION MANUAL MODEL 2455T SUBCARRIER MODULATOR
INSTRUCTION MANUAL MODEL 2455T SUBCARRIER MODULATOR Data, drawings, and other material contained herein are proprietary to Cross Technologies, Inc., and may not be reproduced or duplicated in any form
100U1000. Features. 100 watts CW 100kHz 1000MHz Class A Portable Full VSWR tolerant CE & RoHS Compliant High Efficiency
Specifications 100U1000 Class A Portable Full VSWR tolerant CE & RoHS Compliant High Efficiency Features The Model 100U1000 is a solid-state, selfcontained, air-cooled, broadband amplifier designed for
TIA-527 Balanced Optical/Electrical Converter. Operating Instructions
TIA-527 Balanced Optical/Electrical Converter Operating Instructions Terahertz Technologies Inc.169 Clear Road Oriskany NY 13424 (315) 736-3642 FAX (315) 736-4078 E-mail sales@terahertztechnologies.com
Balanced Photoreceivers Models 1607-AC & 1617-AC
USER S GUIDE Balanced Photoreceivers Models 1607-AC & 1617-AC NEW FOCUS, Inc. 2630 Walsh Ave. Santa Clara, CA 95051-0905 USA phone: (408) 980 8088 Fax: (408) 980 8883 e-mail: contact@newfocus.com www.newfocus.com
RF-LAMBDA LEADER OF RF BROADBAND SOLUTIONS
80W Broadband High Power Amplifier Module 20-1000MHz Electrical Specifications, T A = +25⁰C, VDD = +28V Features Broadband High Power High Efficiency Great Linearity Small Size & Light Weight Low Distortion
Model 4402B. Ultra-Pure Sinewave Oscillator 1Hz to 110kHz Typical Distortion of % Serial No. Operating Manual
Model 4402B Ultra-Pure Sinewave Oscillator 1Hz to 110kHz Typical Distortion of 0.0005% Serial No. Operating Manual 15 Jonathan Drive, Unit 4, Brockton, MA 02301 U.S.A. Tel: (508) 580-1660; Fax: (508) 583-8989
MODEL 25D MANUAL PRODUCT OVERVIEW:
MODEL 25D MANUAL PRODUCT OVERVIEW: The Model 25D drive electronics is a high voltage push-pull power amplifier capable of output voltage swings in the order of 175v P-P, push-pull. The Model 25D provides
Signal Generator Extension Modules Operational Manual
216 Signal Generator Extension Modules Operational Manual 979 Second Street SE, Suite 39 Charlottesville, VA 2292-6172 (USA) Tel: 434.297.327; Fax: 434.297.328 www.vadiodes.com 21 Virginia Diodes, Inc
GPS10RBN - 10 MHz, GPS Disciplined Rubidium Frequency Standard
GPS10RBN - 10 MHz, GPS Disciplined Rubidium Standard Completely self-contained unit. No extra P.C needed. Full information available via LCD. Rubidium Oscillator locked to GPS satellite signal. Accuracy
Varactor-Tuned Oscillators. Technical Data. VTO-8000 Series. Pin Configuration TO-8V
H Varactor-Tuned Oscillators Technical Data VTO-8 Series Features 6 MHz to.5 Coverage Fast Tuning +7 to + dbm Output Power ±1.5 db Output Flatness Hermetic Thin-film Construction Description HP VTO-8 Series
Sintec Optronics Technology Pte Ltd 10 Bukit Batok Crescent #07-02 The Spire Singapore Tel: Fax:
Sintec Optronics Technology Pte Ltd Sintec Optronics Technology Pte Ltd 10 Bukit Batok Crescent #07-02 The Spire Singapore 658079 Tel: +65 63167112 Fax: +65 63167113 Acousto-Optic Modulators By virtue
SDI SPECTRADYNAMICS, INC. HIGH PERFORMANCE DISTRIBUTION AMPLIFIER OPERATING MANUAL
SPECTRADYNAMICS, INC. HIGH PERFORMANCE DISTRIBUTION AMPLIFIER HPDA15RMC OPERATING MANUAL SPECTRADYNAMICS, INC 1849 Cherry St. Unit 2. Louisville, CO 80027 Phone: (303) 6651852 Fax: (303) 6046088 www.spectradynamics.com
Phase Combined Systems
100W Ku-Band 1:2 Phase Combined SSPA System with FPRC-1200 Controller 1 kw C-Band, 1:1 Phase Combined High Power Outdoor SSPA System FEATURES 125W Ku-Band 1:1 Phase Combined SSPB System with FPRC-1100
QCXXX-YYDC-ZZZ-AAV. Compact Low Power RF Driver: For Acousto-optic Q-Switch or Modulator. Description: Key Features: Applications:
ompact Low Power RF Driver: For cousto-optic Q-Switch or Modulator QXXX-YYD-ZZZ-V Former Model Numbers: R390XX-YYDMZZZ & MQ0XX-YYDZZZ-V Description: The QXXX-YYD-ZZZ-V module is a compact Low Power RF
Block Upconverters for Integration in High Power Amplifiers
R Back to Block/Fixed Tuned Converters Block Upconverters for Integration in High Power Amplifiers Block Upconverters For Integration In High Power Amplifiers C-, X- and Ku-Band Models (except UPBA-13)
OPERATING AND MAINTENANCE MANUAL
5Hz to 1MHz WIDE RANGE FULLY AUTOMATIC DISTORTION ANALYZER MODEL 6900B SERIAL NO. OPERATING AND MAINTENANCE MANUAL Unit 4, 15 Jonathan Drive, Brockton, MA 02301-5566 Tel: (508) 580-1660; Fax: (508) 583-8989
Harris IRT Enterprises Multi-Channel Digital Resistance Tester Model XR
Harris IRT Enterprises Multi-Channel Digital Resistance Tester Model 6012-06XR Specifications & Dimensions 2 Theory of Operation 3 System Block Diagram 4 Operator Controls & Connectors 5 Test Connections
Features. = +25 C, 50 Ohm System. Return Loss (Input and Output) 5-18 GHz 8 db
v.89 4 ANALOG PHASE SHIFTER Typical Applications The is ideal for: Fiber Optics Military Test Equipment Features Wide Bandwidth: Phase Shift: >4 Single Positive Voltage Control Small Size: 2. x 1.6 x.1
RC2 REMOTE LEVEL CONTROL MODULE OPERATING INSTRUCTIONS
RC REMOTE LEVEL CONTROL MODULE OPERATING INSTRUCTIONS and trouble-shooting guide LECTROSONICS, INC. Rio Rancho, NM INTRODUCTION The RC Remote Level Control Module provides channels of DC remote control
RS3400W/04 77 GHz Radar Sensor
Features Complete 76-77GHz band FMCW Radar Front End Synthesized frequency source Wideband Sweep Description The RS34W/4 is a W-band FMCW radar front end featuring synthesized frequency sweeps. A fast
Wilcoxon Research PA8HF power amplifier Operating guide
Wilcoxon Research PA8HF power amplifier Operating guide Meggitt Sensing Systems 20511 Seneca Meadows Parkway, Germantown MD 20876, USA Meggitt (Maryland), Inc d/b/a Meggitt Sensing Systems 97012 Rev C.1
RF-LAMBDA LEADER OF RF BROADBAND SOLUTIONS
50W Broadband High Power Amplifier Module 500 2500MHz Electrical Specifications, T A = +25⁰C, Vdd = +28V Features Ultra-broadband Amplifier Module Small and lightweight Supply Voltage: +28V Parameter Min.
Technical Datasheet GT-1000B Microwave Power Amplifier. 100 MHz to 20 GHz. Broadband High-Power Instrumentation Amplifier Rev.
Technical Datasheet GT-1000B Microwave Power Amplifier 100 MHz to 20 GHz Broadband High-Power Instrumentation Amplifier 35113-Rev.A / US050113 Advanced Amplifier Technology 100 MHz to 20 GHz eliminates
LMS Series Lab Brick Synthesized Signal Generator
Product Specification LMS Series Lab Brick Synthesized Signal Generator Features/Benefits > Cost effective, fast switching signal generators to 2 GHz > Includes easy to use virtual front panel GUI program
PA8HF power amplifier Operating guide
PA8HF power amplifier Operating guide Wilcoxon Sensing Technologies 8435 Progress Drive, Frederick, MD 21701, USA Amphenol (Maryland), Inc d/b/a Wilcoxon Sensing Technologies Tel: +1 (301) 330-8811 Tel:
INSTRUCTION MANUAL OTOT-1000C-FQ WIDE-BAND 1550NM DIRECT-MOD QAM TRANSMITTER. 1,000 MHz Bandwidth / Optical Output Power is +9dBm (OTOT-1000C-09-FQ)
INSTRUCTION MANUAL OTOT-1000C-FQ WIDE-BAND 1550NM DIRECT-MOD QAM TRANSMITTER 1,000 MHz Bandwidth / Optical Output Power is +9dBm (OTOT-1000C-09-FQ) Phone: (209) 586-1022 (800) 545-1022 Fax: (209) 586-1026
SIGNAL GENERATORS. MG3633A 10 khz to 2700 MHz SYNTHESIZED SIGNAL GENERATOR GPIB
SYNTHESIZED SIGNAL GENERATOR MG3633A GPIB For Evaluating of Quasi-Microwaves and Measuring High-Performance Receivers The MG3633A has excellent resolution, switching speed, signal purity, and a high output
OX-204 at 10 MHz Ultra Low Phase Noise Oven Controlled Crystal Oscillator
OX-204 at 10 MHz Ultra Low Phase Noise Oven Controlled Crystal Oscillator OX-204 OX-204 The OX-204 is an Ultra Low Phase Noise Ovenized Crystal Oscillator with a noise floor as low as -175 dbc/hz. Designed
HMC346MS8G / 346MS8GE
Typical Applications v7.18 Features This attenuator is ideal for use as a VVA for DC - 8 GHz applications: Point-to-Point Radio VSAT Radio Functional Diagram Wide Bandwidth: DC - 8 GHz Low Phase Shift
INSTALLATION AND OPERATING MANUAL
INSTALLATION AND OPERATING MANUAL FOR RBDA-PCS-1/25W-90-A INDOOR REPEATER TABLE OF CONTENTS PARAGRAPH PAGE NO BDA OVERVIEW 3 BDA BLOCK DIAGRAM DESCRIPTION 3 FCC INFORMATION FOR USER 3 BDA BLOCK DIAGRAM