915MHz Transmit/Receive Module
|
|
|
- Colin Randall
- 5 years ago
- Views:
Transcription
1 RF MHz Transmit/Receive Module This module is intended for 915MHz AMR solutions. It provides separate ports for Rx and Tx paths and two ports on the output for connecting a diversity solution or a test port. The PA section provides a nominal output power of 26dBm. RF6599 Package: 28-pin, 5.5mm x 5.0mm Features Tx Output Power: 26dBm Tx Gain: 14dB Rx Insertion Loss: 1dB Antenna Diversity Switch VREG 24 VCC Applications Wireless Automated Metering 2 21 Wireless Alarm Systems 3 20 Portable Battery Powered Equipment 4 19 Smart Energy ANT TX 6 17 ANT RX TX_RX_SEL VCC ANT_SEL Functional Block Diagram Ordering Information RF6599 Standard 25-piece bag RF6599SR Standard 100-piece reel RF6599TR7 Standard 750-piece reel RF6599TR13 Standard 2500-piece reel RF6599PCBK-410 Fully assembled evaluation board w/5 piece bag Revision DS of 9 Disclaimer: Subject to change without notice
2 Absolute Maximum Ratings Parameter Rating Unit Battery Voltage 5 V RF Port Impedance 50 W Operating Temperature -30 to 70 C Storage Temperature -40 to 85 C ESD, HBM (RF pins) 500 V ESD, HBM (All pins) 500 V ESD, CDN (RF pins) 500 V ESD, CDM (all pins) 500 V MSL MSL 3 Maximum Input Power to PA* +20 dbm *Maximum Input Power with a 50Ω Load Caution! ESD sensitive device. RFMD Green: RoHS status based on EU Directive 2011/65/EU (at time of this document revision), halogen free per IEC , < 1000ppm each of antimony trioxide in polymeric materials and red phosphorus as a flame retardant, and <2% antimony in solder. Exceeding any one or a combination of the Absolute Maximum Rating conditions may cause permanent damage to the device. Extended application of Absolute Maximum Rating conditions to the device may reduce device reliability. Specified typical performance or functional operation of the device under Absolute Maximum Rating conditions is not implied. Nominal Operating Parameters Parameter Specification Min Typ Max Unit Condition Power Amplifier Frequency Range MHz CW Output Power dbm Large Signal Gain, Min Supply Voltage Large Signal Gain, Typ Supply Voltage Large Signal Gain, Max Supply Voltage Output Harmonic Levels 2nd -30 dbc 3rd through 10th -67 dbc Input Return Loss 10 db Power Supply Voltage Current VCC V VREG VCC-0.2 V db VCC = 3.3V, Temperature = -30 C db VCC = 3.3V, Temperature = 25 C db VCC = 3.3V, Temperature = 70 C db VCC = 3.6V, Temperature = -30 C db VCC = 3.6V, Temperature = 25 C db VCC = 3.6V, Temperature = 70 C db VCC = 4.0V, Temperature = -30 C db VCC = 4.0V, Temperature = 25 C db VCC = 4.0V, Temperature = 70 C Operating VCC ma VCC = 3.6V, POUT = 26dBm Operating VREG 3 4 ma VCC = 3.6V, TXRX_SEL = High, ANT_SEL = High or Low, VREG = High, Temperature = 25 C Tx Idle Current ma VCC = 3.6V, VREG = 3.4V, ANT_SEL = TXRX_SEL = 3.4V at POUT = 0dBm Module Leakage ua VCC = 3.6V TXRX_SEL, ANT_SEL and VREG = 0.0V Revision DS of 9 Disclaimer: Subject to change without notice
3 Parameter Specification Min Typ Max Unit Condition Rx Path Frequency Range MHz Insertion Loss db Input IP dbm Input Return Loss 10 db Output Return Loss 10 db Current VCC = 3.6V, TXRX_SEL = Low, ANT_SEL = High or Low, VREG = High ANT1 80 ma ANT_SEL = High, VREG = Low, TXRX_Sel = Low Power Down Mode, ANT2 1.2 ma ANT_SEL = Low, VREG = Low, TXRX_Sel = Low Antenna Switch and Logic Isolation 20 db Any used port to any unused port Logic Voltage High VCC-0.2 V All Logic I/O s Logic Voltage Low V All Logic I/O s Logic Current, High ma All Logic I/O s Module Logic Truth Table Operating Mode ANT_SEL TXRX_SEL TX - ANT1 HIGH HIGH TX - ANT2 LOW HIGH RX - ANT1 HIGH LOW RX - ANT2 LOW LOW Revision DS of 9 Disclaimer: Subject to change without notice
4 Typical Performance Revision DS of 9 Disclaimer: Subject to change without notice
5 Revision DS of 9 Disclaimer: Subject to change without notice
6 Evaluation Board Schematic 500MHz to 1000MHz Application Circuit Revision DS of 9 Disclaimer: Subject to change without notice
7 Pin Out VCC VREG ANT TX 6 17 ANT RX TX_RX_SEL VCC ANT_SEL Package Outline and Branding Drawing All units in µm Revision DS of 9 Disclaimer: Subject to change without notice
8 PCB Patterns Revision DS of 9 Disclaimer: Subject to change without notice
9 Pin Names and Descriptions Pin Name Description 1 Ground 2 Ground 3 Ground 4 Ground 5 ANT2 Antenna 2 Output/Input 6 Ground 7 ANT1 Antenna 1 Output/Input 8 Ground 9 ANT_SEL Antenna Selection Control Line 10 VCC Diversity Switch Supply Voltage 11 TXRX_SEL Transmit or Receive Selection Control Lone 12 Ground 13 Ground 14 Ground 15 Ground 16 RX Receive Port 17 Ground 18 TX Transmit Port 19 Ground 20 Ground 21 Ground 22 Ground 23 VCC Power Amplifier Supply Voltage 24 VREG Power Amplifier Supply Voltage 25 Ground 26 Ground 27 Ground 28 Ground 29 Center Ground Flag Revision DS of 9 Disclaimer: Subject to change without notice
10 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Qorvo: RFFM8550TR7 RF5375SR
RFFM MHz Transmit/Receive Module
925MHz Transmit/Receive Module This module is intended for 868MHz and 915MHz AMR solutions. The FEM provides separate ports for Rx/Tx paths, single-ended Tx and single-ended Rx or Rx differential port,
RF V TO 4.0V,915MHz Transmit/Receive
3.3V to 4.0V,9MHz Transmit/Receive Module RF639 3.3V TO 4.0V,9MHz Transmit/Receive Module Package: LGA, 8-Pin,.mm x.0mm Features Tx Output Power: dbm Separate 0 Tx/Rx Transceiver Interface Rx Insertion
RFFM V to 4.0V, 450MHz to 470MHz Transmit/Receive Front End Module
.V to.0v, 0MHz to 0MHz Transmit/Receive Front End Module Package Style: LGA, 8-Pin,.mm x.0mm NC 8 Features Tx Output Power: 0dBm Tx Gain: 0dB Separate 0Ω Tx/Rx Transceiver Interface Rx Insertion Loss:
RF V TO 4.0V, 915MHz TRANSMIT/RECEIVE MODULE
RF6693.1V to 4.V, 91MHz Transmit/Receive Module RF669 3.1V TO 4.V, 91MHz TRANSMIT/RECEIVE MODULE Package: LGA, 28-Pin,.mm x.mm ASW_RX BAL_IN 1 28 27 26 2 24 23 22 Features Tx Output Power: 3dBm NC 2 3
RFFM V to 4.2V, ISM Band, 1W, 405MHz to 475MHz Transmit/Receive Module. Features. Applications. Ordering Information
RFFM6403 2.5V to 4.2V, ISM Band, 1W, 405MHz to 475MHz Transmit/Receive Module The RFFM6403 is a single-chip front end module (FEM) for applications in the 405MHz and 475MHz ISM Bands. The RFFM6403 addresses
SAW BPF SW2_OUT GND GND 868/915 RFIO SW2 GND 450 RFIO GND CTL1 CTL2 CTL LOGIC CTL3 CTL4 CTL5 VDIG. Product Description. Ordering Information
2.7V to 4.4V, 9MHz Transmit/Receive Module; Thru Mode 4MHz to 928MHz RF6549 2.7V to 4.4V, 9MHz Transmit/Receive Module; Thru Mode 4MHz to 928MHz Package: LGA, 32-Pin, 6mm x 6mm TX TX SAW BPF SAW BPF SW2_OUT
RFFM4503TR7. Features. Applications. Ordering Information. Package: Laminate, 16-pin, 3.0mm x 3.0mm x 1.0mm
RFFM4503 4.9GHz to 5.85GHz 802.11a/n/ac Wi-Fi Front End Module The RFFM4503 provides a complete integrated solution in a single front end module (FEM) for Wi-Fi 802.11a/n/ac systems. The ultrasmall factor
RF V to 4.2V, 2.4GHz Front End Module
3.0V to 4.2V, 2.4GHz Front End Module Package Style: QFN, 20-Pin, 3.5mm x 3.5mm x 0.5mm TXCT _BAIS GND NC 15 14 13 12 11 Features TX Output Power: 23dBm TX Gain: 28dB RX Gain: 11.5dB RX NF: 3dB Integrated
RF3241SR. RF3241 Quad-Band GSM, Polar EDGE Transmit Module, Six UMTS TRX Switch Ports
Quad-Band GSM, Polar EDGE Transmit Module, Six UMTS TRX Switch Ports The RF3241 is a quad-band GSM/GPRS, Polar EDGE transmit module with six interchangeable RF switch ports. The power amplifier supports
RF V TO 3.6V, 2.4GHz FRONT END MODULE
3.V TO 3.6V, 2.4GHz FRONT END MODULE Package Style: QFN, 2-Pin, 3.mmx3.mmx.mm NC VBAT VBAT NC 4 3 2 Features Tx Output Power=22dBm Integrated RF Front End Module with TX/RX switch, PA, filter, and DP2T
RFFM V to 5.0V, 2.4GHz to 2.5GHz b/g/n/ac WiFi Front End Module. Features. Applications. Ordering Information
3.0V to 5.0V, 2.4GHz to 2.5GHz 802.11b/g/n/ac WiFi Front End Module The RFFM4293 provides a complete integrated solution in a single front end module (FEM) for WiFi 802.11b/g/n/ac and Bluetooth systems.
RFFM8500Q. 4.9GHz to 5.85GHz a/n Front End Module. Features. Applications. Ordering Information
4.9GHz to 5.85GHz 802.11a/n Front End Module The RFFM8500Q provides a complete integrated solution in a single Front End Module (FEM) for WiFi 802.11a/n systems. The ultra small form factor and integrated
RF V TO 4.2V, 2.4GHz FRONT END MODULE
3.V TO 4.2V, 2.4GHz FRONT END MODULE Package Style: QFN, 2-Pin, 3.5mmx3.5mmx.5mm TXCT GND VCC_BAIS VCC NC 15 14 13 12 11 Features TX Output Power: 22dBm RX Gain: 11.5dB RX NF: 2.5dB Integrated RF Front
RFFM8511TR7. 4.9GHz to 5.85GHz a/n/ac WiFi Front End Module. Features. Applications. Ordering Information
4.9GHz to 5.85GHz 802.11a/n/ac WiFi Front End Module The provides a complete integrated solution in a single front end module (FEM) for WiFi 802.11a/n/ac systems. The ultra-small factor and integrated
RFSW6062 Low Insertion High Isolation SP6T Switch 5MHz to 6000MHz
Low Insertion High Isolation SP6T Switch 5MHz to 6000MHz The RFSW6062 is a low loss, high isolation SP6T switch with performance optimized for use in Cellular BTS applications. Plus it is also ideally
GND GND RFN BALUN RFP GND. Product Description. Ordering Information. Standard 2500 piece reel. GaAs HBT GaAs MESFET InGaP HBT
RFFM0.0V TO.V,.GHZ FRONT END MODULE Package Style: Laminate, -Pin, mm x mm x mm C_RX_TX VCCLNA N/C ANTSEL 0 9 CE 8 Features Tx Output Power=dBm Integrated RF Front End Module with Balun, PA, filter, LNA
RF V TO 4.0V, 470MHz to 510MHz TRANSMIT/RECEIVE MODULE
3.3V to 4.0V, 470MHz to 510MHz Transmit/Receive Module 3.3V TO 4.0V, 470MHz to 510MHz TRNSMIT/REEIVE MODULE Package: LG, 8-Pin, 5.5mm x 5.0mm VReg V 1 8 7 6 5 4 3 Features Tx Output Power: 30dm Separate
RF V TO 4.5V, 915MHZ ISM BAND TRANSMIT/RECEIVE MODULE
4.0V to 4.5V, 915MHz ISM AND TRANS- MIT/REEIVE MODULE 4.0V TO 4.5V, 915MHZ ISM AND TRANSMIT/REEIVE MODULE Package: LGA, 28-pin, 6mm x 6mm DAV1 N PAV2 1 28 27 26 25 24 23 22 Features Tx Output Power: 28dm
LNA In. Input Match. LNA Vref. LNA Sel. RX Switch. TX Switch GND. PA Vcc2 GND GND. PA Out. Product Description. GaAs HBT GaAs MESFET InGaP HBT
3.0V to 4.2V, ISM Band Transmit/Receive Module with Diversity Transfer Switch RFFM6904 3.0V TO 4.2V, ISM BAND TRANSMIT/RECEIVE MODULE WITH DIVERSITY TRANSFER SWITCH Package: LGA, 32-pin, 8mm x 8mm x 1.2mm
RFSA3043TR7. 75Ω Voltage Controlled Attenuator 5MHz to 3000MHz. Features. Applications. Ordering Information RFSA3043
75Ω Voltage Controlled Attenuator 5MHz to 3000MHz RFMD s RFSA3043 is a fully monolithic analog voltage controlled attenuator (VCA) featuring exceptional linearity over a typical temperature compensated
RFVC1800 Wideband MMIC VCO with Buffer Amplifier 8GHz to 12GHz
Wideband MMIC VCO with Buffer Amplifier 8GHz to 12GHz RFMD s wideband voltage controlled oscillator is a GaAs InGaP HBT MMIC with integrated VCO core and RF output buffer. The part operates from a single
RFVC GHz to 12.1GHz MMIC VCO with Fo/2 and Fo/4 Outputs
10.8GHz to 12.1GHz MMIC VCO with Fo/2 and Fo/4 Outputs RFMD's RFVC1844 is a 5V InGaP MMIC VCO with an integrated frequency divider providing additional Fo/2 and Fo/4 outputs. With an Fo frequency range
RFVC1843TR7. 9.8GHz to 11.3GHz MMIC VCO with Fo/2 and Fo/4 Outputs. Features. Applications. Ordering Information
RFVC1843 9.8GHz to 11.3GHz MMIC VCO with Fo/2 and Fo/4 Outputs RFMD's RFVC1843 is a 5V InGaP MMIC VCO with an integrated frequency divider providing additional Fo/2 and Fo/4 outputs. With an Fo frequency
RF2436 TRANSMIT/RECEIVE SWITCH
Transmit/Receive Switch RF2436 TRANSMIT/RECEIVE SWITCH Package Style: SOT-5 Features Single Positive Power Supply Low Current Consumption db Insertion Loss at 900MHz 24dB Crosstalk Isolation at 900MHz
SGL0363Z. 5MHz to 2000MHz Low Noise Amplifier. Germanium. Simplified Device Schematic. Vpc. Narrow-band Matching Network. Gnd
5MHz to MHz Low Noise Amplifier Silicon Germanium 5MHz to MHz LOW NOISE AMPLIFIER SILICON GERMANIUM Package: SOT-363 Product Description RFMD s is a low power, low noise amplifier. It is designed for.7v
CMOS 5GHz WLAN ac RFeIC WITH PA, LNA AND SPDT
CMOS 5GHz WLAN 802.11ac RFeIC WITH PA, LNA AND SPDT RX LEN 16 RXEN ANT 15 14 13 12 11 Description RFX8051 is a highly integrated, single-chip, single-die RFeIC (RF Front-end Integrated Circuit) which incorporates
Product Description. Ordering Information. GaAs MESFET Si BiCMOS
Digital Controlled Variable Gain Amplifier 1700MHz to 2400MHz RFDA2077 DIGITAL CONTROLLED VARIABLE GAIN AMPLIFIER 1700MHz to 2400MHz Package: MCM 32-Pin, 7.0mmx7.0mm Features Dual Channel VGA Frequency
RFDA3016 Digital Controlled Variable Gain Amplifier 3000MHz to 3800MHz, 6-Bit 0.5dB LSB Control
Digital Controlled Variable Gain Amplifier 3MHz to 38MHz, 6- Bit.dB LSB Control RFDA316 Digital Controlled Variable Gain Amplifier 3MHz to 38MHz, 6-Bit.dB LSB Control Package: MCM 28-Pin, 6.mm x 6.mm 28
CMOS 2.4GHZ ZIGBEE/ISM TRANSMIT/RECEIVE RFeIC
CMOS 2.4GHZ ZIGBEE/ISM TRANSMIT/RECEIVE RFeIC Description 17 1 2 3 4 TXRX VDD VDD D 16 15 14 13 12 11 10 ANT 9 The RFX2401C is a fully integrated, single-chip, single-die RFeIC (RF Front-end Integrated
RF8889A SP10T ANTENNA SWITCH MODULE
SP10T ANTENNA SWITCH MOD- ULE RF8889A SP10T ANTENNA SWITCH MODULE Package: QFN, 3.0mmx3.8mmx0.85mm GSM Rx1 RF8889A GSM Rx2 Features Broadband Performance Suitable for all Cellular Modulation Schemes up
CMOS 5GHz WLAN ac RFeIC WITH PA, LNA AND SPDT
CMOS 5GHz WLAN 802.11ac RFeIC WITH PA, LNA AND SPDT RX LEN 16 RXEN ANT 15 14 13 12 11 Description RFX8051B is a highly integrated, single-chip, single-die RFeIC (RF Front-end Integrated Circuit) which
LNA VCC RX OUT TX IN VREG. Product Description. Ordering Information. Standard 25 piece bag Standard 2500 piece reel. GaAs HBT GaAs MESFET InGaP HBT
2.4GHz TO 2.5GHz, 802.11b/g/n SINGLE-BAND FRONT END MODULE Package Style: QFN, 16-pin, 3.0 x 3.0 x 0.5 mm LNA EN C RX C TX BT 16 15 14 13 Features Single Module Radio Front- End Single Supply Voltage 3.0V
RFGA0024. InGaP HBT. 1000MHz. Product Description. Ordering Information
InGaP HBT MMIC Amplifier 5MHz TO 1MHz RFGA24 InGaP HBT MMIC Amplifier 5MHz TO 1MHz Package: SOT-89 Features Low Cost Broadband Gain Internally Matched Internal Active Bias No Dropping Resistor Single Supply
DATA GND VCC GND RF1 GND GND GND. Product Description. Ordering Information. Sample bag with 25 pieces 7 Sample reel with 100 pieces
Serial Controlled 75W Digital Step Attenuator 5MHz to 2000MHz, 6- Bit, LSB SERIAL CONTROLLED 75 DIGITAL STEP ATTENUATOR 5MHz TO 2000MHz, 6-BIT, Package: MCM, 24-Pin, 4.2mm x 4.2mm Features Frequency Range
RFDA4005TR13. 6-Bit, Digital Controlled Variable Gain Amplifier 50MHz to 4000MHz
6-Bit, Digital Controlled Variable Gain Amplifier 50MHz to 4000MHz RFMD s RFDA4005 is a digitally controlled variable gain amplifier featuring high linearity over the entire gain control range with noise
2.4 GHz TX / RX Booster With Diversity Switch for IoT / BLE / ZigBee
2.4 GHz TX / RX Booster With Diversity Switch for IoT / BLE / ZigBee NC DNC NC TXRX 21 1 2 3 4 5 VDD VDD 20 19 18 DNC DNC 17 16 6 7 8 9 TXEN RXEN PDET Mode 10 SWant 15 IND 14 ANTA 13 12 ANTB 11 DESCRIPTION
RFFM8216TR7-5K. 2.4 GHz Integrated Wi-Fi Front-End Module
RFFM8216 2.4 GHz Integrated Wi-Fi Front-End Module Product Overview The RFFM8216 provides a complete integrated solution in a single front end module (FEM) for WiFi 802.11b/g/n/ac systems.performance is
GND GND GND. Product Description. Ordering Information. Sample bag with 25 pieces 7 Sample reel with 100 pieces. GaAs MESFET Si BiCMOS Si CMOS Si BJT
Temperature Compensating Attenuator TEMPERATURE COMPENSATING ATTENUATOR Package: QFN, 16-Pin,.9mm x 3mm x 3mm GND VDD GND GND 16 15 14 13 Features Patent Pending Circuit Architecture Broadband 5MHz to
RF V TO 4.2V, 2.4GHz FRONT-END MODULE
3.0V TO 4.2V, 2.4GHz FRONT-END MODULE Package Style: QFN, 20-Pin, 3.5mmx3.5mmx0.5mm Features TX Output Power: 22dBm TX Gain: 28dB RX Gain: 11.5dB RX NF: 2.5dB Integrated LNA With Bypass Mode Applications
RF V, SWITCH AND LNA FRONT END SOLUTION
3.3V, SWITCH AND LNA FRONT END SOLUTION Package Style: QFN, -pin, 2mmx2mmx0.5mm C_BT 9 BT GND 7 Features Single Supply Voltage 3.0V to.5v Integrated SP3T Switch and LNA With Bypass Typical gain is db and
RFDA0056 Digital Controlled Variable Gain Amplifier 300MHz to 1100MHz, 6-Bit 0.5dB LSB Control
Digital Controlled Variable Gain Amplifier 3MHz to MHz, 6- Bit.dB LSB Control RFDA6 Digital Controlled Variable Gain Amplifier 3MHz to MHz, 6-Bit.dB LSB Control Package: MCM 8-Pin, 6.mm x 6.mm 8 7 6 3
RFPA3805TR13. GaAs HBT 2-Stage Power Amplifier 700MHz to 2700MHz
GaAs HBT 2-Stage Power Amplifier 700MHz to 2700MHz RFMD s RFPA3805 is a GaAs HBT linear power amplifier specifically designed for Wireless Infrastructure applications. Using a highly reliable GaAs HBT
Product Description. Ordering Information. GaAs HBT GaAs MESFET InGaP HBT
RECEIVE AGC AMPLIFIER Package Style: MSOP-8 Features Supports Basestation Applications -55dB to +51dB Gain Control Range at 85MHz Single 3V Power Supply IN+ 1 IN- 2 GND 3 8 VCC1 7 VCC2 6 OUT+ -2dBm Input
Not For New Design FMS W GaAs phemt SPDT SWITCH. Product Description. Features. Applications
10W GaAs phemt SPDT Switch FMS2031-001 10W GaAs phemt SPDT SWITCH Package: 3 mm x 3 mm QFN Product Description The FMS2031-001 is a 10 W, Single-pole, Double-throw, (SPDT) GaAs phemt reflective antenna
ML485-G. Applications. Functional Block Diagram. Product Features. General Description. Pin Configuration. Ordering Information
RFMD + TriQuint = Qorvo ML 1.-3.2 GHz High IP3 Mixer with Integrated LO Amp Applications PCS / 3G Base station / Repeaters WCDMA / LTE WiMax / WiBro ISM / Fixed Wireless HPA Feedback Paths Product Features
SGA2363ZDC to 5000MHz, Cascadable. SiGe HBT. MMIC Amplifier. Frequency (GHz) 5000 MHz >10dB
DC to 5MHz, Cascadable SiGe HBT MMIC Amplifier SGA233Z DC to 5MHz, CASCADABLE SiGe HBT MMIC AMPLIFIER Package: SOT-33 Product Description The SGA233Z is a high performance SiGe HBT MMIC Amplifier. A Darlington
VCC1 GND IN GND LOP LON GND GND. Product Description. GaAs HBT GaAs MESFET InGaP HBT
Direct Quadrature Modulator 145MHz to 27MHz RFMD214 DIRECT QUADRATURE MODULATOR 145MHz TO 27MHz Package: QFN, 24-Pin, 4mm x 4mm VCC1 IN IP 24 23 22 21 2 19 Features ACPR Performance: -7dBc Typ. for 1-Carrier
RFFM3482Q 2.4GHz to 2.5GHz, Automotive WiFi Front End Module
2.4GHz to 2.5GHz, Automotive WiFi Front End Module Package Style: QFN, 16-pin, 3mm x 3mm x 0.45mm RXBN RXBP GND ANT 16 15 14 13 Features Single Voltage Supply 3.3V to 4.2V Integrated 2.5GHz b/g/n Amplifier,
GHz RF Front-End Module. o C
Functional Block Diagram Features 4 High Efficient Power Amplifier: 41% at Pout= 23dBm -PA P-1dB: +21dBM Typical @ +3.3V-PA Low Noise Amplifier (NF typical 1.8dB)-LNA Low Insertion Loss:0.4dB@ 2.45GHz-Switch
QPF4206BTR7. Wi-Fi Front End Module. Product Overview. Key Features. Functional Block Diagram. Applications. Ordering Information PRELIMINARY
Product Overview The Qorvo is an integrated front end module (FEM) designed for Wi-Fi 802.11ax systems. The compact form factor and integrated matching minimizes layout area in the application. Performance
RFDA0035 DIGITAL CONTROLLED IF DUAL VGA 5 BIT 1dB LSB CONTROL
Digital Controlled IF Dual VGA RFDA0035 DIGITAL CONTROLLED IF DUAL VGA 5 BIT 1dB LSB CONTROL Package: QFN 32-Pin, 5.0mmx5.0mm 32 31 29 OPB- A1 A0 IPA+ IPA- GNDA VCCA OPA+ OPA- 28 27 26 25 Features Dual
RFPA TO 5 V PROGRAMMABLE GAIN HIGH EFFICIENCY POWER AMPLIFIER
3 TO 5 V PROGRAMMABLE GAIN HIGH EFFICIENCY POWER AMPLIFIER Package Style: QFN, 16-Pin, 3 mm x 3 mm Features 0.5 W CW Output Power at 3.6 V 1 W CW Output Power at 5 V 32 db Small Signal Gain at 900 MHz
SDA-3000 GaAs Distributed Amplifier
GaAs Distributed Amplifier RFMD s SDA-3000 is a directly coupled (DC) GaAs microwave monolithic integrated circuit (MMIC) driver amplifier die designed for use as a Mach Zehnder Modulated (MZM) laser driver
SKY LF: PHEMT GaAs IC High-Power 4-CTL DPDT Switch LF 6 GHz
data sheet SKY13318-321LF: PHEMT GaAs IC High-Power 4-CTL DPDT Switch LF 6 GHz Features l Application 82.11a (5.2 5.8 GHz) and 82.11b, (2.4 GHz) diversity l Operating frequency LF 6 GHz l Positive low
2.4GHZ CMOS WLAN / BT DUAL-MODE RFEIC WITH PA, LNA & SP3T
2.4GHZ CMOS WLAN / BT DUAL-MODE RFEIC WITH PA, LNA & SP3T ANT DESCRIPTION DET VMODE 1 2 3 16 15 14 13 12 11 10 RFX8425 is a pure CMOS-based, single-chip/single-die RFeIC (RF Front-end Integrated Circuit)
QPF4200SR. Wi-Fi Front End Module. Product Overview. Key Features. Functional Block Diagram. Applications. Ordering Information
Product Overview The Qorvo QPF4200 is an integrated front end module (FEM) designed for Wi-Fi 802.11ax systems. The compact form factor and integrated matching minimizes layout area in the application.
SBB MHz to 6000MHz InGaP HBT ACTIVE BIAS GAIN BLOCK. Features. Product Description. Applications
50 to 6000 InGaP HBT Active Bias Gain Block SBB3000 50 to 6000 InGaP HBT ACTIVE BIAS GAIN BLOCK Package: Bare Die Product Description RFMD s SBB3000 is a high performance InGaP HBT MMIC amplifier utilizing
SGA3363Z. = 35 ma (Typ.) Frequency (GHz) T L MHz >10dB 255 C/W
SGA3363Z DC to MHz, CASCADABLE SiGe HBT MMIC AMPLIFIER Package: SOT-363 Product Description The SGA3363Z is a high performance SiGe HBT MMIC Amplifier. A Darlington configuration featuring one-micron emitters
Absolute Maximum Ratings Parameter Rating Unit V D1, V D2, V D3 +8 V V G 0 V Junction Temperature C Continuous P DISS (T = ) C/W (derate 37 mw/ C abov
9.8GHz to 13.5GHz High Linearity RFPA1002 9.8GHz TO 13.5GHz HIGH LINEARITY POWER AMPLIFIER Package: Ceramic QFN, -pin, 6mm x 6mm x 0.95mm 38 Vd1 Vg2 Vd2a 37 36 34 33 1 Features Frequency Range: 9.8GHz
RF3932D 60W GaN on SiC Power Amplifier Die
60W GaN on SiC Power Amplifier Die RF3932D Package: Die The RF3932D is a 48V, 60W, GaN on SiC high power discrete amplifier die designed for commercial wireless infrastructure, cellular and WiMAX infrastructure,
CMOS 5GHz WLAN a/n/ac RFeIC WITH PA, LNA, AND SPDT
CMOS 5GHz WLAN 802.11a/n/ac RFeIC WITH PA, LNA, AND SPDT Description RX 1 2 LNA_EN 16 ANT 15 14 13 12 11 RFX8055 is a highly integrated, single-chip, single-die RFeIC (RF Front-end Integrated Circuit)
Product Description. Ordering Information. GaAs MESFET Si BiCMOS Si CMOS Si BJT. DRAFT DRAFT1 of
UPSTREAM CATV AMPLI- FIER UPSTREAM CATV AMPLIFIER Package: QFN, -Pin, 4mm x 4mm Features Single.V Supply Operation Low Power Consumption: 14mA Typical 6db Dynamic Range: -.5dBm To 61dBmV Output Excellent
RF3826TR13. 9W GaN Wide-Band Power Amplifier 30MHz to 2500MHz. Features. Applications. Ordering Information RF3826
9W GaN Wide-Band Power Amplifier 30MHz to 2500MHz The RF3826 is a wideband Power Amplifier designed for CW and pulsed applications such as wireless infrastructure, RADAR, two way radios, and general purpose
Gain and Return Loss vs Frequency. s22. Frequency (GHz)
SBA4086Z DCto5GHz, CASCADABLE InGaP/GaAs HBT MMIC AMPLIFIER Package: SOT-86 Product Description RFMD s SBA4086Z is a high performance InGaP/GaAs Heterojunction Bipolar Transistor MMIC Amplifier. A Darlington
RF3376 General Purpose Amplifier
General Purpose Amplifier RF3376 General Purpose Amplifier Package Style: SOT8 Features DC to >6000MHz Operation Internally Matched Input and Output 22dB Small Signal Gain +2.0dB Noise Figure +11dBm Output
CMOS 2.4GHZ TRANSMIT/RECEIVE WLAN RFeIC
CMOS 2.4GHZ TRANSMIT/RECEIVE WLAN RFeIC 17 1 RX 2 3 VDD VDD DNC 16 15 14 13 12 11 10 ANT Description The RFX2402C is a fully integrated, single-chip, single-die RFeIC (RF Front-end Integrated Circuit)
SGA2463Z. Frequency (GHz) 18.0 dbm 1950MHz. 7.2 dbm 1950 MHz 255 C/W
SGA243Z DC to 5MHz, CASCADABLE SiGe HBT MMIC AMPLIFIER Package: SOT-33 Product Description The SGA243Z is a high performance SiGe HBT MMIC Amplifier. A Darlington configuration featuring one-micron emitters
N/C GND LOIN GND N/C N/C N/C N/C. VLOA1 VLOA2 N/C N/C Vc1 Vc2 Vg2 VMPA. Product Description. Ordering Information
RFUV173 RFUV173 21GHz TO 26.GHz GaAs MMIC IQ UPCONVERTER Package: QFN, 32-Pin, mm x mm x.9mm N/C GND I N/C GND Q N/C Vg1 32 31 3 29 28 27 26 2 Features RF Frequency: 21GHz to 26.GHz LO Frequency (LSB):
Absolute Maximum Ratings Parameter Rating Unit Voltage 6.0 V Maximum input power (0.6 GHz to 2.5 GHz), RF1, RF2 +28 dbm Operating temperature -30 to +
Product Overview The is a single-pole double-throw (SPDT) switch designed for general purpose switching applications which require very low insertion loss and medium power handling capability. The is ideally
RFSW1012SR. Broadband SPDT Switch. Product Overview. Key Features. Functional Block Diagram. Ordering Information
Product Overview The is a single-pole double-throw (SPDT) switch designed for applications requiring very low insertion loss and high power handling capability. The excellent linearity performance of the
TQM EVB. Not for New Designs BC14/BC1/B25 BAW Duplexer. Applications. Functional Block Diagram. Product Features. General Description
TQM96314 Applications CDMA/LTE handset, data card & mobile router applications using the extension PCS band (Band Class 14) / BC1 / B25 8 Pin 2.6 x 2.1 x.88 mm Product Features Excellent Triple Beat Performance:
Simplified Device Schematic. Pin 18. Pin 8. Pin 16. Stage 1 Bias. Stage 2 Bias. Pin 10
7MHz to 2.7GHz 5V 1W Power Amplifier SZA-244(Z) 7MHz to 2.7GHz 5V 1W Power Amplifier Package: QFN, 4mm x 4mm Product Description RFMD s SZA-244 is a high efficiency class AB heterojunction bipolar transistor
DATA SHEET SE2436L: High Power 2.4 GHz Front End Module. Product Description. Applications
Applications Smart Meters In-home appliances Smart thermostats Features Integrated PA with 27 dbm output power Integrated LNA with programmable bypass Integrated antenna switching with Tx and Rx diversity
RF5633 SINGLE 5.0V, 3.3 TO 3.8GHZ LINEAR POWER AMPLIFIER
Single 5.0V, 3.3 to 3.8GHz Linear Power Amplifier RF5633 SINGLE 5.0V, 3.3 TO 3.8GHZ LINEAR POWER AMPLIFIER Package Style: QFN, 24-Pin, 4 mm x 4 mm x 0.9 mm Features High Gain; 34dB Supports Low Gain Mode
CMOS 2.4GHZ ZIGBEE/ISM TRANSMIT/RECEIVE RFeIC
CMOS 2.4GHZ ZIGBEE/ISM TRANSMIT/RECEIVE RFeIC Description 17 1 2 3 4 TXRX VDD VDD D 16 15 14 13 12 11 10 ANT 9 The is a fully integrated, single-chip, single-die RFeIC (RF Front-end Integrated Circuit)
DATA SHEET SE2568U: 2.4 GHz High Efficiency Wireless LAN PA Preliminary Applications. Product Description. Features. Ordering Information
Applications Product Description IEEE802.11b DSSS WLAN IEEE802.11g OFDM WLAN IEEE802.11n OFDM WLAN General Applications Features Dual Mode IEEE802.11b & IEEE802.11g Integrated PA, digital bias control,
Product Description. Ordering Information. GaAs HBT GaAs MESFET InGaP HBT
RFPA38 GaAs HBT 15MHz TO 96MHz POWER AMPLIFIER Package: SOIC-8 Features 5W Output Power (P1dB) High Linearity: OIP3>48dBm High Efficiency Low Noise: NF=3.2dB at 945MHz 5V to 7V Operation Thermally Enhanced
QPB9325SR. High Power Switch LNA Module. Product Overview. Key Features. Functional Block Diagram. Applications. Ordering Information
Product Overview The Qorvo is a highly integrated front-end module targeted for TDD macro or picocell base stations. The switch module integrates RF functional blocks such as a pin-diode based high power
RF2162 3V 900MHz LINEAR AMPLIFIER
3V 900MHz LINEAR AMPLIFIER Package Style: QFN, 16-Pin, 4x4 Features Single 3V Supply 9dBm Linear Output Power 9dB Linear Gain 35% Linear Efficiency Onboard Power Down Mode 800MHz to 960MHz Operation Applications
TQP MHz Power Amplifier. General Description. Product Features. Functional Block Diagram. Ordering Information
General Description The is a high-efficiency two-stage power amplifier in a low-cost surface-mount package. The amplifier is able to achieve 31% power added efficiency at +27 dbm output power while operating
RF1136 BROADBAND LOW POWER SP3T SWITCH
BROADBAND LOW POWER SP3T SWITCH Package Style: QFN, 12-Pin, 2.5 mm x 2.5 mm x 0.6 mm Features Low Frequency - 3.5 GHz Operations Very Low Insertion Loss: Cell Band 0.25 db PCS Band 0.30 db High Isolation:
Data Sheet. ACMD-6103 Band 3 Duplexer. Description. Features. Specifications. Applications. Functional Block Diagram
ACMD-613 Band 3 Duplexer Data Sheet Description The Avago Technologies ACMD-613 is a highly miniaturized duplexer designed for use in LTE Band 3 (171 1785 MHz UL, 185 188 MHz DL) handsets and mobile data
RFPA GHz TO 5.9GHz 2W InGaP AMPLIFIER
4.9GHz to 5.9GHz 2W InGaP AMPLI- FIER RFPA5026 4.9GHz TO 5.9GHz 2W InGaP AMPLIFIER Package: DFN, 6-pin, 5.59mm x 6.23mm x 0.85mm Vcc Features P1dB=33dBm at 5V 802.11g 54Mb/s Class AB Performance P OUT
SKY : 2.4 GHz Transmit/Receive Front-End Module with Integrated Low-Noise Amplifier
DATA SHEET SKY65344-21: 2.4 GHz Transmit/Receive Front-End Module with Integrated Low-Noise Amplifier Applications 2.4 GHz ISM band radios ZigBee FEMs IEEE 802.15.4 applications Features Transmit output
CMOS 2.4GHZ ZIGBEE/ISM TRANSMIT/RECEIVE RFeIC
hot RFX2401C CMOS 2.4GHZ ZIGBEE/ISM TRANSMIT/RECEIVE RFeIC Description 1 2 3 4 TXRX 17 VDD VDD DNC 16 15 14 13 12 11 10 ANT 9 The RFX2401C is a fully integrated, single-chip, single-die RFeIC (RF Front-end
QPL7210TR7. 2.4GHz Wi-Fi LNA+BAW Receive Module. Product Overview. Key Features. Functional Block Diagram. Applications. Ordering Information
2.4GHz Wi-Fi LNA+BAW Receive Module Product Overview The provides a complete integrated receive solution in a single placement front end module (FEM) for Wi-Fi 802.11a/n/ac systems. The full integration
DATA SHEET SE2431L: 2.4 GHz ZigBee/ Front-End Module Preliminary Datasheet. Product Description. Applications
Applications Smart Meters In-home appliances Smart thermostats Features Integrated PA with up to 24 dbm output power Integrated LNA with programmable bypass Integrated antenna switching with Tx and Rx
Absolute Maximum Ratings Parameter Rating Unit Drain Voltage (V D ) 150 V Gate Voltage (V G ) -8 to +2 V Gate Current (I G ) 39 ma Operational Voltage
60W GaN WIDEBAND POWER AMPLIFIER Package: Hermetic 2-Pin Flanged Ceramic Features Broadband Operation DC to 3.5GHz Advanced GaN HEMT Technology Advanced Heat-Sink Technology Small Signal Gain = db at 2GHz
Absolute Maximum Ratings Parameter Rating Unit Max Input Power, OFDM Modulated, 3:1 Load VSWR +39 dbm Max Input Power, 2:1 VSWR +41 dbm ESD HBM Rating
1W GaAs phemt SPDT Switch FMS231-1 1W GaAs phemt SPDT SWITCH Package: 3mmx3mm QFN Product Description The FMS231-1 is a 1W, Single-pole, Double-throw, (SPDT) GaAs phemt reflective antenna switch. The switch
QPC6054SR. Product Description. Product Features. Functional Block Diagram. Applications. Ordering Information
RFC VSS/ V3 Product Description The is a Silicon on Insulator (SOI) single-pole, 5- throw (SP5T) switch design for use in cellular, 3G, LTE and other high performance communications systems. It offers
75 VOLTAGE CONTROLLED ATTENUATOR GND RFIN. Product Description. Ordering Information. GaAs MESFET Si BiCMOS Si CMOS Si BJT
RFS313 75W Voltage Controlled ttenuator RFS313 75 VOLTGE CONTROLLED TTENUTOR Package Style: QFN, 16-Pin,.9mm x 3mm x 3mm MODE VDD VC GND 16 15 14 13 Features Patent Pending Circuit rchitecture roadband
Data Sheet. ACMD-6103 Band 3 Duplexer. Description. Features. Specifications. Applications. Functional Block Diagram
ACMD-613 Band 3 Duplexer Data Sheet Description The Avago Technologies ACMD-613 is a highly miniaturized duplexer designed for use in LTE Band 3 (171 1785 MHz UL, 185 188 MHz DL) handsets and mobile data
RFX8425: 2.4 GHz CMOS WLAN/Bluetooth Dual-Mode RFeIC with PA, LNA, and SP3T
DATA SHEET RFX8425: 2.4 GHz CMOS WLAN/Bluetooth Dual-Mode RFeIC with PA, LNA, and SP3T Applications Smartphones, feature phones. and MIDs with WLAN/Bluetooth WLAN/Bluetooth platforms requiring shared antenna
RFX8053: CMOS 5 GHz WLAN ac RFeIC with PA, LNA, and SPDT
DATA SHEET RFX8053: CMOS 5 GHz WLAN 802.11ac RFeIC with PA, LNA, and SPDT Applications 802.11a/n/ac WiFi devices Smartphones Tablets/MIDs Gaming Consumer electronics Notebooks/netbooks/ultrabooks Mobile/portable
SE2431L: 2.4 GHz ZigBee / Front-End Module
DATA SHEET SE431L:.4 GHz ZigBee /0.15.4 Front-End Module Applications Smart meters In-home appliances Smart thermostats Features Integrated: PA with up to +4 dbm output power LNA with programmable bypass
QPB9324SR. High Power Switch LNA Module. Product Overview. Key Features. Functional Block Diagram. Applications. Ordering Information
Product Overview The Qorvo is a highly integrated front-end module targeted for TDD macro or picocell base stations. The switch module integrates RF functional blocks such as a pin-diode based high power
DATA SHEET SE2576L: 2.4 GHz High Power Wireless LAN Power Amplifier Preliminary. Product Description. Applications. Features. Ordering Information
Applications IEEE802.11b DSSS WLAN IEEE802.11g,n OFDM WLAN Access Points Features Dual Mode IEEE802.11b, IEEE802.11g, IEEE802.11n 26 dbm, EVM = 3%, 802.11g, OFDM 54 Mbps 29 dbm, 802.11b mask compliant
Specification Min. Typ. Max.
High Power Reflective GaAs SP4T Switch FMS2016-005 HIGH POWER REFLECTIVE GaAs SP4T SWITCH Package: 3 mm x 3 mm QFN Product Description The FMS2016-005 is a low loss, high power, linear single-pole four-throw
Data Sheet. ACMD-6307 LTE Band 7 Duplexer. Description. Features. Specifications. Applications. Functional Block Diagram
ACMD-637 LTE Band 7 Duplexer Data Sheet Description The Avago ACMD-637 is a highly miniaturized duplexer designed for use in LTE Band 7 (25 257 MHz UL, 262 269 MHz DL) handsets and mobile data terminals.
RF V TO 5.0V, 3.3GHz TO 3.8GHz LINEAR POWER AMPLIFIER
3.0V to 5.0V, 3.3GHz to 3.8GHz Linear Power Amplifier RF5603 3.0V TO 5.0V, 3.3GHz TO 3.8GHz LINEAR POWER AMPLIFIER Package Style: QFN, 16-Pin, 3mmx3mmx0.45mm Features High Gain; 32dB 2.5% EVM (RMS) at