VERIFYING THE ACCURACY OF WIRE CLOTH SIEVES
|
|
- Olivia Mason
- 5 years ago
- Views:
Transcription
1 Test Procedure for VERIFYING THE ACCURACY OF WIRE CLOTH SIEVES Texas Department of Transportation TxDOT Designation: Tex-907-K Effective Dates: August 1999 August SCOPE 1.1 This test procedure describes methods for both the visual examination of wire cloth sieves for defects and proper construction and for the verification of the wire cloth for dimensional accuracy. 1.2 The values given in parentheses (if provided) are not standard and may not be exact mathematical conversions. Use each system of units separately. Combining values from the two systems may result in nonconformance with the standard. 2. REFERENCE DOCUMENTS 2.1 ASTM E AASHTO M 92. PART I VISUAL EXAMINATION 3. APPARATUS 3.1 Evenly lighted background. 4. PROCEDURE 4.1 Perform at six-month intervals. 4.2 Visually examine the sieve, viewing through the wire cloth toward an evenly lighted background, to aid inspection of the openings. 4.3 The wire cloth should be of brass, bronze, or stainless steel, but not coated or plated. Reject if the cloth has punctures, obvious defects, creases, wrinkles, is loose, or if any opening appears distorted, damaged or off size compared to others. CONSTRUCTION DIVISION /99 08/11
2 4.4 The wire should be uniformly fastened to the frame. s of 710 µm (No. 25) and smaller should be smoothly soldered around the periphery of the screen with no crevices to catch fine material. 4.5 The frame shall be of seamless construction, made of brass or stainless steel Reject if the sieve is new and the frame is cracked If the sieve is used and the frame cracked, repair by brazing or soldering with a smooth finish. 4.6 Frames shall fit into each other with an easy sliding fit. Dimensions should be according to Table The sieve should have a label containing: a reference to ASTM E 11 or ASTM specifications the metric size (i.e., in millimeters or microns) the sieve designation as given in Table 2, Column 2 and the name of the manufacturer or distributor. Table 1 Standard Frame Dimensions, mm Nominal in inches (see Note 1) Average, in millimeters Typical Frame Height from top to Wire Cloth, in millimeters (see Note 2) Frame inside diameter (@5 mm from top) Frame Outside to to to to to to Note 1 Other diameters or shapes may be specified by the user. Note 2 Other heights may be used. Table 2 Nominal Dimensions and Variations for Wire Cloth s in Each Maximum Maximum ½ ½ CONSTRUCTION DIVISION /99 08/11
3 Table 2 Nominal Dimensions and Variations for Wire Cloth s in Each Maximum Maximum ¾ ½ ¼ / / / / / / / / No. 3½ No No No No No No No No No No No No No No No No No No No No No No No No No No No No CONSTRUCTION DIVISION /99 08/11
4 Table 2 Nominal Dimensions and Variations for Wire Cloth s in Each Maximum Maximum No No No No PART II PHYSICAL EXAMINATION 5. APPARATUS 5.1 Dial or digital calipers. 5.2 Optical comparator, either projection-type or hand held, with internal scales. 6. PROCEDURE 6.1 Perform at time of purchase and as needed. 6.2 The design, readability, and precision of the measuring device should permit accurate measurement of the width of the openings and the diameter of the wires. Use a projection-type optical comparator equipped with ruled screens matched to lenses or a digital readout, or a hand-held magnifier with an internal scale. Dial or digital calipers are suitable for larger openings For sieves 16 mm (5/8 in.) and larger, the readability of the measuring device should be at least 0.01 mm For sieves smaller than 16 mm (5/8 in.), the readability device should be at least mm. 6.3 Measure the width of the openings and the diameter of the wires for both directions of the cloth's weave. Keep separate lists of measurements for each direction. Note 3 One direction of the weave the warp and the other is the shoot. For the square openings in these sieves, it is only important to keep the measured values for each direction separate. 6.4 Measure the width and wire size of openings in two or more areas of the sieve. Measure at least ten openings in each direction in each area. For sieves with 20 or fewer openings, measure all openings. 6.5 Take measurements at or near the midpoint of the openings. CONSTRUCTION DIVISION /99 08/11
5 6.6 Average the openings in each direction separately. Reject if either or both average values do not fall within the range of Table 2, Column Count all openings in each direction, separately, whose width falls within the range in Table 2, Column 4. Reject the sieve if this number is greater than five percent of the total number of width measurements in that direction. If the sieve has less than fifty openings, reject if there are more than three openings outside this range in either direction. 6.8 Reject the sieve if any opening is larger than the value in Table 2, Column Average the diameter of the wires in each direction separately. Reject the sieve if either average falls outside the Table 2, Column 6 range Verify that the frame dimensions meet the requirements of Table 1. CONSTRUCTION DIVISION /99 08/11
Woven Steel Wire Fence Type-47. Under the state specification for fencing, ASTM A 116 is called out.
Woven Steel Wire Fence Type-47 Under the state specification 710.02 for fencing, ASTM A 116 is called out. Go to the steel and fencing certification manual for more information about the basic properties
More informationTex-728-I, Measurements of Dry Film Coating Thickness on Steel
Thickness on Steel Contents: Section 1 Overview...2 Section 2 Precautions...3 Section 3 Apparatus...4 Section 4 Procedures...5 Texas Department of Transportation 1 08/99 02/08 Section 1 Overview Section
More informationTex-452-A, Rotational Capacity Testing of Fasteners Using a Tension Measuring Device
Using a Tension Measuring Device Contents: Section 1 Overview...2 Section 2 Definitions...3 Section 3 Apparatus...4 Section 4 Part I, Rotational Capacity Testing...5 Section 5 Part II, Values for Fasteners
More informationSECTION Display Case Door Series 1301-CM
1 SECTION 12 3559 Display Case Door Series 1301-CM PART 1 - GENERAL 1.01 SUMMARY A. This section includes: 1. Display Case Glass Doors. 2. Sidelites. B. Related work in other sections: 1. 08 8000- Glazing
More informationDIAL AND VERNIER CALIPERS
TECHNICAL MANUAL INSTRUMENT CALIBRATION PROCEDURE DIAL AND VERNIER CALIPERS THIS PUBLICATION SUPERSEDES NAVAIR 17 20MD 07 DATED 1 JUNE 1995 DISTRIBUTION STATEMENT C. DISTRIBUTION AUTHORIZED TO U.S. GOVERNMENT
More informationNAVSEA STANDARD ITEM
NAVSEA STANDARD ITEM FY-19 DATE: 01 OCT 2017 CATEGORY: I 1. SCOPE: 1.1 Title: Threaded Fastener Requirements; accomplish 2. REFERENCES: 2.1 Standard Items 2.2 S9086-CJ-STM-010/075, Fasteners 3. REQUIREMENTS:
More informationOPERATING PAVEMENT PROFILOGRAPH AND EVALUATING PROFILES
Test Procedure for OPERATING PAVEMENT PROFILOGRAPH AND EVALUATING PROFILES Texas Department of Transportation TxDOT Designation: Tex-1000-S Effective Date: August 1999 1. SCOPE 1.1 This method covers the
More informationStandard Test Method for Measuring Warpage of Ceramic Tile 1
Designation: C 485 09 Standard Test Method for Measuring Warpage of Ceramic Tile This standard is issued under the fixed designation C 485; the number immediately following the designation indicates the
More informationMetrology Prof.Dr Kanakuppi Sadashivappa Bapuji Institute of Engineering and Technology Davangere
Metrology Prof.Dr Kanakuppi Sadashivappa Bapuji Institute of Engineering and Technology Davangere Lecture 33 Electrical and Electronic Comparators, Optical comparators (Refer Slide Time: 00:17) I welcome
More informationACCELERATED POLISH TEST FOR COARSE AGGREGATE
Test Procedure for ACCELERATED POLISH TEST FOR COARSE AGGREGATE TxDOT Designation: Tex-438-A Effective Date: August 1999 1. SCOPE 1.1 Use this method to estimate the polish and relative wear of coarse
More informationProcedure for Testing Direct Tension Indicators (DTI) Assemblies
Procedure for Testing Direct Tension Indicators (DTI) Assemblies 1. Scope: This test is to ensure that the bolt will be at or above the specified minimum bolt tension after installation when the direct
More informationI-W07/W77. Couplings DETAIL A WARNING. Photo Showing Pipe with Weld Seam Ground 6 inches/152 mm Back from Pipe End and an AGS Groove
WARNING Read and understand all instructions before attempting to install any Victaulic piping products. These products must be used only on pipe that is prepared to Victaulic Advanced Groove System (AGS)
More informationCertificate of Accreditation
PERRY JOHNSON LABORATORY ACCREDITATION, INC. Certificate of Accreditation Perry Johnson Laboratory Accreditation, Inc. has assessed the Laboratory of: (Hereinafter called the Organization) and hereby declares
More informationElcometer Conical Mandrel Bend Tester
English Elcometer 1510 Conical Mandrel Bend Tester Operating Instructions English is a registered trademark of Elcometer Instruments Ltd. All other trademarks acknowledged. Copyright Elcometer Instruments
More informationSIEVE CERTIFICATION SYSTEM
MACHINE VISION SYSTEMS AND TECHNOLOGY Tel: (781) 275-2020 Fax: (781) 275-2028 www.vision-machines.com SIEVE CERTIFICATION SYSTEM Ensure ASTM E11 Compliance! Automated Sieve Certification System (ASCS)
More informationSpecifications - Common Nails Diamond point, Flat head, round smooth shank, Bright, HDG, EG or cement coated (resin or vinyl) finish
Specifications - Common Nails Diamond point, Flat head, round smooth shank, Bright, HDG, EG or cement coated (resin or vinyl) finish ASTM F 1667-05 Table 15 Type 1, Style 10 - Common Nails Size Length
More informationMEDIUM DUTY CAST IRON SLIDE GATES SERIES 20-10C
MEDIUM DUTY CAST IRON SLIDE GATES SERIES 20-10C Revised October 2007 Armtec reserves the right to alter designs. General The Armtec Sluice Gate is a quality and highly economical gate for a variety of
More informationPART MATERIALS. Section Fencing Materials. Description
PART 03000 - MATERIALS Section 03010 - Fencing Materials Description 03010.00 Scope - This section consists of the test requirements, specifications and tolerances for barbed wire, woven wire and chain
More informationNAVSEA STANDARD ITEM T9074-AS-GIB-010/271, Requirements for Nondestructive Testing Methods
NAVSEA STANDARD ITEM ITEM NO: 009-48 DATE: 29 JUL 2011 CATEGORY: II 1. SCOPE: 1.1 Title: Pressure Seal Bonnet Valve; repair (shop) 2. REFERENCES: 2.1 S9086-CJ-STM-010/CH-075, Fasteners 2.2. T9074-AS-GIB-010/271,
More information1.0 DESCRIPTION. This specification covers steel snowplow blades with tungsten carbide inserts.
(Page 1 of 5) (Rev.02-26-09) CARBIDE TIPPED SNOWPLOW BLADES MGS-91-01Q 1.0 DESCRIPTION. This specification covers steel snowplow blades with tungsten carbide inserts. 2.0 MATERIALS. 2.1 Steel. The blades
More information1. There is a variety of casting processes. Many casting process characteristics are similar
CHAPTER 14 Expendable-Mold Casting Processes Review Questions 1. There is a variety of casting processes. Many casting process characteristics are similar but each has distinct characteristics that determine
More informationALLOY STEEL SOCKET SET SCREWS 1
1 IFI NOTE: - is reprinted with permission from the Annual Book of ASTM Standards, copyright American Society for Testing and Materials, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959, U.S.A,
More informationARTICLE 28 VISUAL EXAMINATION STANDARDS
ARTICLE 28 VISUAL EXAMINATION STANDARDS Specification for Classifying Visual Defects in Glass-Reinforced Laminates and [ASTM D 2563-70 Parts Made Therefrom... 639 (1977)] 637 ARTICLE 28 VISUAL EXAMINATION
More informationStandard Test Method for Rubber Deterioration Surface Cracking 1
Designation: D 58 99 Standard Test Method for Rubber Deterioration Surface Cracking This standard is issued under the fixed designation D 58; the number immediately following the designation indicates
More informationCorrosion-Resistant Coated Dowel Bars
Standard Specification for Corrosion-Resistant Coated Dowel Bars AASHTO Designation: M 254-06 (2010) American Association of State Highway and Transportation Officials 444 North Capitol Street N.W., Suite
More informationPlanishing hammer stand For use with SKU Planishing hammer
Planishing hammer stand For use with SKU 94847 Planishing hammer Model 96300 Assembly And Operation Instructions Please Note: Planishing Hammer not included with Stand. Due to continuing improvements,
More informationStandard Specification for Carbon and Alloy Steel Nuts [Metric] 1
Designation: A 563M 04 METRIC Standard Specification for Carbon and Alloy Steel Nuts [Metric] 1 This standard is issued under the fixed designation A 563M; the number immediately following the designation
More informationMetrology lecture-2: Angular Measurement. IE 441: Metrology and Instrumentations Dr. Belal Gharaibeh Fall 2011 UOJ October 27, 2011
Metrology lecture-2: Angular Measurement IE 441: Metrology and Instrumentations Dr. Belal Gharaibeh Fall 2011 UOJ October 27, 2011 1 Angles, minutes and seconds Circles are divided into 360 equal parts,
More informationANSI/BHMA A Revision of ANSI/BHMA A
ANSI/BHMA A156.26-2012 Revision of ANSI/BHMA A156.26-2006 AMERICAN NATIONAL STANDARD FOR CONTINUOUS HINGES SPONSOR BUILDERS HARDWARE MANUFACTURERS ASSOCIATION, INC. Revision B 2/15/2017 Formatted: Centered
More informationMetrology (0) PROMO 13.1E. Resolution:.0005" (0.01mm).0005" (0.01mm) Grads
Metrology PROMO 13.1E Automatic off after 5 minutes with no loss of position Accuracy meets DIN862 Resolution:.0005" (0.01mm).0005" (0.01mm) Grads Call 00 44 (0)1835 863501 today IP67 Electronic Calipers
More informationDETAIL SPECIFICATION SHEET
INCH-POUND MIL-DTL-24308/40 1 April 2015 DETAIL SPECIFICATION SHEET CONNECTORS, ELECTRIC, RECTANGULAR, MINIATURE, COMBINATION INSERT ARRANGEMENT, PLUG, SOCKET CONTACTS, SHELL SIZE 5, SIZE 20 SIGNAL CONTACTS
More informationBevels & Gauges. Measuring & Marking T-SLIDE BEVEL PLASTIC HANDLE T-SLIDE BEVEL - ABS HANDLE SLIDING BEVEL INDICATOR BEVEL PROTRACTOR
T-SLIDE BEVEL - ABS HANDLE For determining existing angles or transferring angles onto a workpiece Slotted hardened steel blade allows the user to accommodate a wide range of different size work pieces
More informationSCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 & ANSI/NSCL Z
SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 & ANSI/NSCL Z540-1-1994 INSPECTION MEASUREMENT COMPANY 2291 Byron Center Ave. S.W. Wyoming, MI 49519-1651 Paul R. Kragt Phone: 616 531 3303 CALIBRATION Valid
More informationModule-4 Lecture-2 Perpendicularity measurement. (Refer Slide Time: 00:13)
Metrology Prof. Dr. Kanakuppi Sadashivappa Department of Industrial and Production Engineering Bapuji Institute of Engineering and Technology-Davangere Module-4 Lecture-2 Perpendicularity measurement (Refer
More information3. SIGNIFICANCE AND USE 3.1 These test methods provide a quantitative measure of the tack property of a pressure sensitive adhesive.
Call Letters PSTC-16 Date of Issuance 10/00 Revised 10/03 Revised 05/07 Loop Tack 1. SCOPE 1.1 This test method is intended to determine the tack properties of a pressure sensitive adhesive. This test
More informationDETAIL SPECIFICATION SHEET
INCH-POUND MIL-DTL-24308/33 1 April 2015 DETAIL SPECIFICATION SHEET CONNECTORS, ELECTRIC, RECTANGULAR, MINIATURE, COMBINATION INSERT ARRANGEMENT, PLUG, PIN CONTACTS, SHELL SIZE 3, SIZE 20 SIGNAL CONTACTS
More informationSSPC-PA 2 Procedure for Determining Conformance to Dry Coating Thickness Requirements
SSPC-PA 2 Procedure for Determining Conformance to Dry Coating Thickness Requirements William D. Corbett, KTA-Tator, Inc. Chair SSPC Committee C.3.2 on Dry Film Thickness Measurement SSPC-PA 2 Procedure
More informationOWNER'S MANUAL TIE ROD, WALL & FLOOR MOUNTED JIBS. Model JIB-HC, JIB-LC, JIB-FM
Vestil Manufacturing Company 999 N. Wayne Street, P.O. Box 507 Angola, IN 6703 USA Phone (60) 665-7586 Fax (60) 665-339 sales@vestil.com www.vestil.com Revised 09-0 A company dedicated to solving ergonomic
More informationTHERMAL PROFILE OF HOT MIX ASPHALT
Test Procedure for THERMAL PROFILE OF HOT MIX ASPHALT TxDOT Designation: Tex-244-F Effective Dates: March 2010 April 2011. Texas Department of Transportation 1. SCOPE 1.1 Use this test method to obtain
More informationProduct Guide Specification
Shield Casework February 2014 3421 Merriam Lane Overland Park, Kansas 66203 Phone 913-744-2183 Fax 913-384-3477 Website www.shieldcasework.com E-mail info@shieldcasework.com Product Guide Specification
More informationDETAIL SPECIFICATION SHEET
INCH-POUND MIL-DTL-24308/30 1 April 2015 DETAIL SPECIFICATION SHEET CONNECTORS, ELECTRIC, RECTANGULAR, MINIATURE, COMBINATION INSERT ARRANGEMENT, RECEPTACLE, SOCKET CONTACTS, SHELL SIZE 1, SIZE 20 SIGNAL
More informationCentury focus and test chart instructions
Century focus and test chart instructions INTENTIONALLY LEFT BLANK Page 2 Table of Contents TABLE OF CONTENTS Introduction Page 4 System Contents Page 4 Resolution: A note from Schneider Optics Page 6
More informationSealing Elements. Technical Handbook O-rings. 15. Tolerances and Surface Imperfections
15. Tolerances and Surface Imperfections Size tolerances and surface imperfections on O-rings are influenced by the tolerance, finish, and cleanliness of the mold cavities from which they are produced.
More informationStandard Specification for Quenched and Tempered Steel Bolts and Studs 1
Designation: A 44 00 Standard Specification for Quenched and Tempered Steel Bolts and Studs This standard is issued under the fixed designation A 44; the number immediately following the designation indicates
More informationDesignation: F
Designation: F 852 05 Standard Specification for Twist Off Type Tension Control Structural Bolt/Nut/Washer Assemblies, Steel, Heat Treated, 20/05 ksi Minimum Tensile Strength This standard is issued under
More informationSPECIAL SPECIFICATION Inch LED Traffic Signal Lamp Unit
1993 Specifications SPECIAL SPECIFICATION 1201 12 Inch LED Traffic Signal Lamp Unit 1. Description. This specification describes the minimum acceptable design and performance requirements for a twelve
More informationMeter Box Access Solutions
Meter Box Access Solutions Table of Contents Meter Box Access Solutions Oval Meter Boxes Round Meter Boxes Rectangular Meter Boxes Meter Pits Adapter Rings Meter Lids Meter Covers, Plates and Lids Accessories
More informationCertificate of Accreditation
PERRY JOHNSON LABORATORY ACCREDITATION, INC. Certificate of Accreditation Perry Johnson Laboratory Accreditation, Inc. has assessed the Laboratory of: Acceso III No. 16 A Nave 10, Parque Industrial Benito
More informationDMS-8290, Glass Traffic Beads
Overview Effective Date: March 2001 April 2003. This specification shall govern for the materials, composition, quality, sampling, and testing of glass traffic beads. Bidders and/or Suppliers Requirements
More information- Flash. A very thin gage, sometimes film-like material, which extends from the parting line projection, shall be removed.
SEALING ELEMENTS 15. Tolerances and Surface Imperfections Size tolerances and surface imperfections on O-rings are influenced by the tolerance, finish, and cleanliness of the mold cavities from which they
More informationTABLE OF CONTENTS. 1.0 Scope. 2.0 References. 3.0 Definitions. 4.0 Submission and Design Requirements. 5.0 Materials 5.1 General 5.
1.0 Scope 2.0 References 3.0 Definitions 4.0 Submission and Design Requirements 5.0 Materials 5.1 General 5.2 Marking 6.0 Equipment 7.0 Production 7.1 Steel Octagonal Poles 7.2 Base Plate 7.3 Top Cap 7.4
More informationStandard Specification for Copper-Clad Steel Wire for Electronic Application 1
Designation: B 45 0 Standard Specification for Copper-Clad Steel Wire for Electronic Application 1 This standard is issued under the fixed designation B 45; the number immediately following the designation
More informationFACULTY OF ENGINEERING DESIGN AND PRODUCTION ENGINEERING DEPARTMENT. Credit Hour System Metrology Lab 1 MDP 240 (1) Fixed gauges. Metrology laboratory
FACULTY OF ENGINEERING DESIGN AND PRODUCTION ENGINEERING DEPARTMENT Report On: Credit Hour System Metrology Lab 1 MDP 240 (1) Fixed gauges Metrology laboratory Class No: B.N. Student Name Remark Signature
More informationSECTION SITE FURNISHINGS FOR CFCRT. 1. American Society for Testing and Materials (ASTM).
PART 1 - GENERAL 1.1 SECTION INCLUDES A. Benches. B. Trash receptacles. C. Bike storage. 1.2 REFERENCE STANDARDS A. Including but not limited to: 1. American Society for Testing and Materials (ASTM). 1.3
More informationSECTION METAL FABRICATIONS
SECTION 05100 PART 1 - GENERAL 1.01 DESCRIPTION A. Section includes specifications for metal fabrications, including minimum requirements for fabricator, and galvanizing. 1.02 REFERENCE STANDARDS A. ASTM
More informationNAVSEA STANDARD ITEM. 2.2 MIL-STD-1689, Fabrication, Welding, and Inspection of Ships Structure
NAVSEA STANDARD ITEM ITEM NO: 009-05 DATE: 18 JUL 2014 CATEGORY: I 1. SCOPE: 1.1 Title: Temporary Accesses; provide 2. REFERENCES: 2.1 Standard Items 2.2 MIL-STD-1689, Fabrication, Welding, and Inspection
More informationTesting. Material testing will be according to applicable AASHTO, ASTM or Department methods as specified.
907.01 Section 907. FENCING MATERIALS 907.01 General Requirements. Materials for use in fencing property, right-of-way and other installations must comply with this section. 907.02 Testing. Material testing
More informationChapter 13 SQUARES HOW TO CHOOSE AND USE THEM TM The Types and Uses section provides you with a list of
Chapter 13 SQUARES HOW TO CHOOSE AND USE THEM The Types and Uses section provides you with a list of the types of squares. These pages should help you select the right square for the job. The Using Squares
More informationTECHNICAL CORRECTION October Process Industry Practices Structural. PIP STF05121 Fabrication and Installation of Anchor Bolts
TECHNICAL CORRECTION October 2006 Process Industry Practices Structural PIP STF05121 Fabrication and Installation of Anchor Bolts PURPOSE AND USE OF PROCESS INDUSTRY PRACTICES In an effort to minimize
More informationSECTION STRUCTURAL STEEL. A. PART A and DIVISION 1 of PART B are hereby made a part of this SECTION.
SECTION 051200 PART 1 GENERAL 1.01 GENERAL REQUIREMENTS A. PART A and DIVISION 1 of PART B are hereby made a part of this SECTION. B. Examine all conditions as they exist at the project prior to submitting
More informationWIRE CLOTH. PRODUCT CATALOG ISO 9001:2008 Certified
WIRE CLOTH PRODUCT CATALOG info@directmetals.com ISO 9001:2008 Certified table of contents SAFETY GRATING wire cloth WE LL CUT ANYTHING IN OUR INVENTORY TO YOUR SPECS! Terminology... 1 Fabricated Filters...
More informationTEST PROCEDURE FOR DYNAMIC PULL-OFF PERFORMANCE OF ROOFING FASTENER HEADS OR FASTENERS WITH BEARING PLATES
TESTING APPLICATION STANDARD (TAS) 117(C)-95 TEST PROCEDURE FOR DYNAMIC PULL-OFF PERFORMANCE OF ROOFING FASTENER HEADS OR FASTENERS WITH BEARING PLATES 1. Scope 1.1 This Protocol covers determination of
More informationH HD Adult Wheelchair Swing Frame & Hangers(perm) IMPORTANT
Page 1 IMPORTANT PLEASE READ THESE INSTRUCTIONS BEFORE COMMENCING ASSEMBLY. All equipment must be installed in accordance with these instructions. Check your shipment against Bill of Lading and Parts list.
More informationSCI-FAB Product Specifications. Casework Section 1. Part 1 General
SCI-FAB Product Specifications Casework Section 1 Part 1 General 1.1 SCOPE OF WORK Includes all factory fabricated stainless steel casework as required by the project drawings. 1.2 TYPICAL INCLUSIONS A.
More informationPROCESS SPECIFICATION SURFACE FINISH REQUIREMENTS
3260 East Universal Way Tucson, Arizona 85756 PROCESS SPECIFICATION SURFACE FINISH REQUIREMENTS PS00000020 DATE OF ISSUE 08/14/2015 REVISION 02 PROPRIETARY NOTICE This document is not to be distributed
More informationPRODUCT CATALOGUE. Major Features: Arc Bends Manufactured to: Pipestar now offering full-line of flanged Arcbends
PRODUCT CATALOGUE Pipestar now offering full-line of flanged Arcbends Pipestar offers a range of seamless long radius Arc HDPE sweep bends made to the highest quality standards. Pipestar offers a range
More informationPLANNED SIGN PROGRAM CHECKLIST
Planning and Building Agency Planning Division 20 Civic Center Plaza P.O. Box 1988 (M-20) Santa Ana, CA 92702 (714) 647-5804 PLANNED SIGN PROGRAM CHECKLIST Applicant, please return this checklist with
More informationImage + Archiving 129
After Treatment After processing your films, burning image files to a CD, enlarging or printing pictures, there is still something to do. For example, pictures and prints have to be trimmed. Trimmers like
More informationFootwear Foot Grounders Resistive Characterization (not to include static control shoes)
for the Protection of Electrostatic Discharge Susceptible Items- Footwear Foot Grounders Resistive Characterization (not to include static control shoes) Electrostatic Discharge Association 7900 Turin
More informationProducing sheet metal components and assemblies. Outcome one
006 UNIT 022 Producing sheet metal components and assemblies Learning outcomes 1 2 Know how to produce sheet metal components and assemblies Performance evidence must be the main form of evidence gathered.
More informationETCHED PLAQUES by Matthews International
ETCHED PLAQUES by Matthews International Note: These specifications were current at the time of publication but are subject to change without notice. Please confirm the accuracy of these specifications
More informationGovernment Recognized Export House OHSAS 18001:2007 ISO 14001:2004 PED Approved Company.
Government Recognized Export House OHSAS 800:200 ISO 400:2004 PED Approved Company. Phone : +9 22 44 (2 Lines) Fax : +9 22 289 4 Email : export@reliablepipes.com domestic@reliablepipes.com Designation:
More informationTCC/SHORE TRANSIT BUS MAINTENANCE FACILITY - PHASE II
SECTION 101400 - SIGNAGE PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and supplementary Conditions and Division-1 Specification Sections,
More informationCOOL-SHIELD AUTO-DARKENING FILTER CARTRIDGE (ADF) HELMETS
COOL-SHIELD AUTO-DARKENING FILTER CARTRIDGE (ADF) HELMETS IM0000 February, 2009 This manual covers equipment which is no longer in production by The Lincoln Electric Co. Specifications and availability
More informationMSP-DCCLFSD LCD Flat Screen Swing-Down Mount
INSTALLATION INSTRUCTIONS LCD Flat Screen Swing-Down Mount Perfect for home applications under kitchen cabinets or other rooms with a soffit. The LCD Flat Screen Swing-Down mount is a sturdy, versatile
More informationLAARMANN. Sieving Machines and Test Sieves. Innovators in Solids
Innovators in Solids Sieving Machines and Test Sieves Digital Sieving Machines for dry, wet and air jet sieving Stainless steel test sieves with precision wire mesh, perforated plates and electroformed
More informationPrecision Manufacturing
Precision Manufacturing 216 North Main Street. Freeport, NY 11520 Phone: 888-260-7466 / Fax: 516-771-6444 sales@ondrivesus.com www.ondrivesus.com Know Linear Your Shaft Shoulder Supports Screws By Dennis
More informationMILITARY SPECIFICATION
MIL-R-47196A(MI) 6 September 1977 SUPERSEDING MIL-R-46196(MI) 12 July 1974 MILITARY SPECIFICATION RIVETS, BUCK TYPE, PREPARATION FOR AND INSTALLATION OF This specification is approved for use by US Army
More informationCertificate of Accreditation
PERRY JOHNSON LABORATORY ACCREDITATION, INC. Certificate of Accreditation has assessed the Laboratory of: Rays Precision Calibration, Inc 881-3 Nandino Blvd., Lexington, KY 40511 (Hereinafter called the
More informationInstallation Guidelines. Next Dimension. Single Hung / Single Hung Fixed / Double Hung / Sliding Window / Fixed Window
Installation Guidelines Next Dimension Single Hung / Single Hung Fixed / Double Hung / Sliding Window / Fixed Window Windsor Windows & Doors Windsor Windows & Doors 900 S. 19 th St. 2210 Stafford St. Extn
More informationRR-F-191/1D 14 May SUPERCEDING RR-F-191/1C July 22, 1981 FEDERAL SPECIFICATION SHEET
14 May 1990 ----------- SUPERCEDING RR-F-191/1C July 22, 1981 FEDERAL SPECIFICATION SHEET FENCING, WIRE AND POST METAL (CHAIN-LINK FENCE FABRIC) (DETAIL SPECIFICATION) This Federal Specification is approved
More information9 QUICK RELEASE WOODWORKING VISE
9 QUICK RELEASE WOODWORKING VISE 94386 OPERATING INSTRUCTIONS Due to continuing improvements, actual product may differ slightly from the product described herein. 349 Mission Oaks Blvd., Camarillo, CA
More informationOWNER S MANUAL. Safety. Please read this owner s manual before use and keep it at hand for reference. Warranty
Please read this owner s manual before use and keep it at hand for reference. OWNER S MANUAL Safety Important safety instructions for using the INCRA Miter5000 Before using the INCRA Miter5000, read and
More informationGeneric Multilayer Specifications for Rigid PCB s
Generic Multilayer Specifications for Rigid PCB s 1.1 GENERAL 1.1.1 This specification has been developed for the fabrication of rigid SMT and Mixed Technology Multilayer Printed Circuit Boards (PCB's)
More informationStandard Specification for Standard Nominal Diameters and Cross-Sectional Areas of AWG Sizes of Solid Round Wires Used as Electrical Conductors 1
Designation: B 258 02 Standard Specification for Standard Nominal Diameters and Cross-Sectional Areas of AWG Sizes of Solid Round Wires Used as Electrical Conductors 1 This standard is issued under the
More informationStandard Test Method for Grading Spun Yarns for Appearance 1
Designation: D 2255 02 Standard Test Method for Grading Spun Yarns for Appearance 1 This standard is issued under the fixed designation D 2255; the number immediately following the designation indicates
More informationMachining Laboratory Regulations and Safety
Machining Laboratory Regulations and Safety General Laboratory Regulations Each person using the manufacturing laboratory is expected to comply with the following rules and regulations failure to do so
More informationDECKS. Stairway illumination Positive attachment of ledger Lateral load connection required board (R507.2) required (R ) (R311.7.
DECKS Max. riser height-7 ¾ Min. tread depth-10 Landings required at (R311.7.5.1) (R311.7.5.2) top and bottom of stairs (R311.7.6) Notched guardrail post NOT allowed Graspable handrail required Spacing
More informationMANUFACTURING INC. Specifications
Page 1 of 4 GENERAL 11 Aluminum security screen doors must be tested by a recognized testing laboratory to conform to SMA 6001-2002 Proposed American National Standard Specifications for Metal Protection
More informationRequirements for Polarizing Grid
Requirements for Polarizing Grid Document: ARO-340570-A-REQ Version A Status: DRAFT Prepared by: Names(s) and Signature(s) Robert W. Freund Date 11-Mar-2005 Approved by: Name and Signature Date Released
More informationMinimum Requirements for Digital Radiography Equipment and Measurement Procedures by Different Industries and Standard Organizations
uwe.ewert@bam.de Minimum Requirements for Digital Radiography Equipment and Measurement Procedures by Different Industries and Standard Organizations Uwe Ewert and Uwe Zscherpel BAM Federal Institute for
More informationProcedure for Wrench Calibration and Snug Tightening
Procedure for Wrench Calibration and Snug Tightening 1. Scope: This procedure provides the method for calibration of a manual torque wrench or an adjustable impact wrench and the snug tightening procedure
More informationSECTION FRAMELESS GLASS SLIDING BI-FOLD SHOWER DOOR HARDWARE
1 SECTION 10 2880 FRAMELESS GLASS SLIDING BI-FOLD SHOWER DOOR HARDWARE PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions
More informationRELINER INSIDE DROP SYSTEM SPECIFICATIONS
1. PRODUCT NAME RELINER INSIDE DROP SYSTEM U.S. Patent 6074130 Canadian Patent # 2269565 All RELINER Products are proudly made in the U.S.A. 2. MANUFACTURER RELINER /Duran Inc. 53 Mount Archer Rd. Lyme
More informationStandard Specification for High-Strength Bolts for Structural Steel Joints [Metric] 1
Designation: A 325M 00 METRIC An American National Standard Standard Specification for High-Strength Bolts for Structural Steel Joints [Metric] 1 This standard is issued under the fixed designation A 325M;
More informationMathey Dearman Single and Double Screw Chain Clamp Parts & Operating Manual
Machine Model Serial# WHERE THERE S PIPE, THERE S MATHEY Mathey Dearman Single and Double Screw Chain Clamp Parts & Operating Manual Revised: 1/9/2018 P. O. Box 472110, Tulsa, OK 74147-2110 USA Toll Free:
More informationInstalling 3M DI-NOC Architectural Finishes on Doors
Installation Guide Revision C, September 2017 Introduction The purpose of this installation guide is to establish a 3M-recommended procedure for installing 3M DI-NOC Architectural Finishes (the Product
More informationSECTION PVC THATCH SHINGLE ROOFING SYSTEM PART 1 GENERAL 1.01 SUMMARY
SECTION 07312 PVC THATCH SHINGLE ROOFING SYSTEM PART 1 GENERAL 1.01 SUMMARY A. This Section Includes the following: 1. Endureed Dominica PVC thatch shingles. 2. Self- adhering sheet underlayment. B. Related
More informationSPECIFICATIONS FOR THE MANUFACTURE AND DESIGN OF PRECAST THREE SIDED ARCH STRUCTURES, WINGWALLS AND HEADWALLS
SPECIFICATIONS FOR THE MANUFACTURE AND DESIGN OF PRECAST THREE SIDED ARCH STRUCTURES, WINGWALLS AND HEADWALLS 1. DESCRIPTION THESE SPECIFICATIONS ARE FOR A PRECAST THREE SIDED ARCH STRUCTURE, HEADWALLS
More informationA. Extent of structural precast concrete work is shown on drawings and in schedules.
SECTION 03 41 00 - STRUCTURAL PRECAST CONCRETE PART 1 GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of Contract, including General and Supplementary Conditions and Division 1 specification
More information