Vinyl Windows and Doors
|
|
- Daniel Ferguson
- 6 years ago
- Views:
Transcription
1 Vinyl Windows and Doors Part Number: V Pella Corporation INSTALLATION INSTRUCTION - INSTRUCCIONES DE INSTALACION 350 SERIES WINDOW INTO EXISTING WOOD FRAME WINDOW Lea las instrucciones en español en el reverso. These instructions were tested and developed for replacing windows in wood-frame wall construction systems designed to manage moisture. This method of installation involves removing the sash only of the existing window. The original window frame will remain in place and only the existing sash, frame stops and frame hardware must be removed. If existing window frame shows signs of water infiltration or is damaged beyond repair, this method should not be followed and the entire existing window should be removed. Installation recommendations for other types of wall construction, wall systems, conditions, multiple windows or bow/bay windows, may be obtained from Pella Corporation or a local Pella retailer. Building designs, construction methods, building materials, and site conditions unique to your project may require an installation method different from these instructions and additional care on your part. Determining the appropriate installation method is the responsibility of you, your architect, or other construction professional. YOU WILL NEED TO SUPPLY: SmartFlash foil backed butyl window and door flashing tape or equivalent Window and Door Insulating Foam Sealant by the Dow Chemical Company or equivalent low pressure polyurethane window and door foam - DO NOT use high pressure or latex foams. Installation will require two or more persons for safety reasons. TOOLS REQUIRED: INSTALLING INTO EXISTING DOUBLE-HUNG OR CASEMENT FRAME FROM THE INTERIOR INSTALLING INTO EXISTING DOUBLE-HUNG FRAME FROM THE EXTERIOR Always read the Vinyl Window and Door Limited Warranty before purchasing or installing Vinyl Windows and Doors manufactured by Pella Corporation. By installing this product, you are acknowledging that this Limited Warranty is part of the terms of the sale. Failure to comply with all Pella installation and maintenance instructions may void your Pella product warranty. See Limited Warranty for complete details at
2 IF INSTALLING WINDOW FROM EXTERIOR, OR REMOVING EXISTING CASEMENT SASH, REFER TO OPTIONAL SASH REMOVAL AT THE END OF THESE INSTRUCTIONS. 1REMOVING EXISTING SASH Caution: Many windows in older homes are painted with lead-based paint. Removal of old windows may disturb this paint. Proper precautions must be taken to minimize exposure to dust and debris. Consult state or local authorities for more information. Use appropriate personal protective equipment. A. Score paint or varnish along interior sash stops with a sharp utility knife. Carefully Set aside to reuse. B. Cut the balance cords on the bottom sash and lift out the sash. Allow weights to fall to the bottom of the weight pocket. C. Remove the parting stops. There may be a small wedge of wood at the bottom of the upper sash that is next to the parting stops. To make it easier to remove the parting stop, use a chisel to knock off the wedge. D. Lower the top sash and cut the balance cords allowing the balance weights to top sash. Be careful not to damage the exterior blind stop. E. Remove the balance cord pulleys. remove balance cord pulleys. If they cannot be removed easily, drive them into the jamb using a hammer. 2OPENING PREPARATION A. Inspect the existing window frame and repair or replace any defective or rotted wood parts. Make sure the exterior blind stops are sound. B. Insulate the weight pocket with loose fill insulation. Note: Use of expanding/aerosol foam insulation is not recommended. C. If applicable, install pre-finished metal flashing or trim to cover existing frame sill and the exterior trim at the head and jambs. D. Clean the opening of any dirt, debris, or excess old paint before proceeding. Note: Many windows in older homes are painted with lead-based paint. See caution note in Step 1. E. Apply one piece of sill flashing tape to the sill of the existing window. Cut the tape the same length as the width of the existing window sill. Place one side of the tape against the vertical leg of the stool, and work the tape into the corner before applying to the sill. Press down firmly. The tape will not cover the sill depth completely under the new window. 2E Note: If needed, blocking/shims may need to be placed where the existing balances were located.
3 F. Ensure existing sill is level. Note: If shimming of the sill is necessary, use a continuous shim that extends across the entire width of the sill. Confirm that the installation jamb screws will fasten into solid wood. If not, insert solid filler at screw locations. Note: Open the sash to access all pre-drilled installation holes. 3PREPARE THE WINDOW FOR INSTALLATION Windows Installed From Interior A. Remove packing materials from the window. Note: Check product for any cracks or penetrations in the frame. DO NOT install damaged windows. B. Install the sill adapter in the sill accessory groove. 3B Sill adapter Sill accessory groove Continuous shim Note: Use a rubber mallet to drive the sill adapter into the sill accessory groove. The vertical leg of the sill adapter may be cut to accommodate different sill angles. If using a CLIP INSTALLION, refer to the installation instructions included with the install clip accessory package. SLIDING WINDOW ONLY C. Remove the venting sash it clears the anti-lift clip. Lift up on the sash until the bottom of the sash will clear the bottom track. And remove the sash towards the interior. D. Remove the vent track from the vent pocket sill. track out of the sill pocket, being careful not to damage it. Keep this part, to be reinstalled later. 3D E. Drill 5/32" installation screw holes the spacing shown in the graphic. The holes should be located in the center of the vent pocket. F. Head/Jamb Only: Counter with a drill guide placed Drill through the first wall only of the frame. DO NOT penetrate the outer wall EXTERIOR JAMB/HEAD 6" 6" 5/32" drill 16" MAX. 6" 4" 4" 6" 3E 16" MAX. Fixed Meeting Rail INTERIOR 1-1/4" 3/8" drill with drill guide placed 1/4" from end of bit.
4 DOUBLE HUNG AND SINGLE HUNG WINDOWS > 40" WIDE ONLY: Remove the sill riser by opening the sash and using a flat headed screw-driver to pry the sill riser from the sill. Starting at one end, push on the top of the sill riser so that a small flatbladed screwdriver can be inserted as shown. Pry sill riser up to remove. 3G First Press Here Then Insert Screwdriver Here Drill 5/32 installation screw holes through the frame sill and head per the spacing shown in the graphic. 6" CENTERED 3H 6" MEETING RAIL I. Counter Drill using a 3/8" drill bit with a drill guide of the bit. Drill through the first wall only of the frame. DO NOT penetrate the drill bit. 3I 1-1/4" 5/32" drill 3/8" drill with drill guide placed 1/4" from end of bit. 5/32" drill 1-1/4"
5 4SEALING AND FASTENING THE WINDOW A. Test fit the window in the opening. With the window closed and locked, set the bottom of the window into the opening, then tilt the top into position. B. Ensure the window is resting against the interior surface of the blind stops and the sill adapter meets the original sill. Note: The height of the window frame can be increased by as much as 3/8" by applying the head expander (included) to the window frame. If more than 3/8" height adjustment is required, install a continuous shim at the sill. DO NOT use the head expander in High Performance installations. C. Apply the head expander (if required). For installation using the head expander, go to INSTALLATION D. Drill two 1/4 weep holes in the sill adapter. Locate hole must be at the bottom of the vertical leg of the sill adapter. E. Apply a 3/8" continuous bead of sealant to the interior face of the existing blind stops at the head and both jambs. 4E F. Place a bead of sealant where the existing stool meets the existing frame sill and jambs. 4F Place a bead of sealant where the jamb and sill meet. 4G
6 Insert the replacement window in the opening by setting the bottom of the window in first, then tilting the top into place. Make sure the window rests against the interior surface of the blind stops and the sill adapter will contact the existing sill. 4H I. Place a shim near the top of one jamb, in line with the top pre-drilled hole in the window frame. Trim all shims Interior 4H 4I Shim 2" screw J. Continue placing shims at each pre-drilled installation screw holes in jambs as needed to plumb and square the window. Check window for squareness by making sure diagonal measurement from corner to corner is K. Pre-drill 1/16" diameter holes in the shims. hole in the frame. Finish inserting the top screw in each jamb. 4J L. Install hole covers in exposed holes. tight spaces in the frame. M. Check window operation. Lock and unlock sash. Open and close all sash. Note: If there are any problems with the operation of the window, recheck shim locations and adjust for plumb and square. 4K 4L Installation Screw Hole Screw Cover
7 5INTERIOR SEAL Caution: Ensure use of low pressure polyurethane window and door insulating foams and strictly follow the foam manufacturer s recommendations for application. Use of high pressure foams or improper application of the foam may cause the window frame to bow and hinder operation. A. Apply insulating foam sealant. From the interior, insert the nozzle of the applicator approximately deep into the space between the window and of foam. This will allow room for expansion the foam and will minimize squeeze out. Apply sealant across interior surface of shims to create continuous seal. Follow foam manufacturer's instructions. Note: It may be necessary to squeeze the end of the tube with pliers to be able insert into the space between the new and existing window frame. DO NOT completely fill the space from the back of the blind stops to the interior face the opening. of to of B. Check window operation by opening and closing the window. Note: If the window does not operate correctly, check to make sure it is still plumb, level, square and that the sides are not bowed. If adjustments are required, remove the foam with a serrated knife. Adjust the shims and reapply the insulating foam sealant. Casements: If additional adjustment is needed, use the adjustment tool and accompanying instructions. 6INTERIOR TRIM A. Reinstall existing interior sash stops or new trim as desired. 7EXTERIOR SEAL WINDOWS INSTALLED FROM INTERIOR: A. If space between the new window frame EXTERIOR install backer rod and then sealant as shown in Steps EXTERIOR Corner beed
8 B. Seal the window to the exterior stops. Place a corner bead of sealant around the perimeter of the window frame where the new frame contacts the original window frame. Also place a bead of sealant between the sill adapter and the bottom of the existing window sill. This bead should connect to the jamb sealant beads. Tool the sealant beads. Proceed to Step 7E. 7B Note: When corner beading sealant around the perimeter of the window frame, be careful not to cover the weep holes at the sill. WINDOWS INSTALLED FROM EXTERIOR (STEP 10): C. Insert backer rod into the space around the window at the head and jambs. This should the backer rod and the exterior face of the window. Note: Backer rod adds shape and depth for the sealant line. 7C D. Seal the window to the exterior stops. Place a corner bead of sealant around the perimeter of the window frame where the new frame contacts the original window frame. Also place a bead of sealant between the sill adapter and the bottom of the existing window sill. This bead should connect to the jamb sealant beads. Tool the sealant beads. Note: When corner beading sealant around the perimeter of the window frame, be careful not to cover the weep holes at the sill. 7D E. Shape, tool, and clean excess sealant. When finished, the sealant should be the shape of an hourglass. Note: This method creates a more flexible sealant line capable of expanding and contracting. EXTERIOR FINISH OF EXISTING FRAME Any exposed wood on the exterior stop needs to be covered/protected. There are many ways to accomplish this, and each case can be unique. Note: The contractor/installer will determine when and how to finish the exterior.
9 OTHER EXISTING SASH REMOVAL INSTRUCTIONS 8INSTALING IN EXISTING CASEMENT FRAME Note: Remove the new window from its packaging. Inspect and measure the new window to confirm it will fit into the opening prior to removing the existing window. The window needs to be 1/2" smaller in both width and height than the existing window frame. A. Remove the existing sash. This will vary per manufacturer fasteners will generally allow the sash to be removed from the existing frame. Note: Two or more people may be required when handling existing sash. B. Remove operator hardware and all head, jamb, and sill stops. This can usually be accomplished with a prybar. 8B 9OPENING PREPARATION A. Inspect the existing window frame and repair or seat any nails. 9B B. Clean the opening of any dirt, debris, or excess old paint before proceeding. Chisel off any high spots. C. Apply one piece of flashing tape to the sill of the existing press down firmly. The tape will not cover the sill depth completely under the new window. D. Ensure existing sill is level. to ensure the sill is level. Note: Improper placement of shims or spacers may result in bowing the bottom of the window. The sill adapter will not be needed in this installation. 9C Return to Step 3.
10 OTHER EXISTING SASH REMOVAL INSTRUCTIONS 10 INSTALLING IN EXISTING DOUBLE-HUNG FRAME FROM EXTERIOR A. Unlock the window. upper sash so both are in the approximate middle of the frame. Note: Most of the following steps may be completed from the exterior of the house. B. Remove the jamb and head parting stop. head parting stop by pulling the stop down from the frame. In some cases, the stops are nailed on and can simply be pulled off. In other situations the stops may need to be pried or cut out of the frame. 10A 10B 10C C. Remove the exterior jamb and head stops. This can be accomplished with a wood chisel, circular saw, reciprocating saw, roto-tool, or equivalent. Ensure the stop is removed flush with the existing window jamb. Caution: Take care to prevent existing sashes from falling out when removing stops. 10D 10E 10C D. Remove the upper and lower sash. This will vary per manufacturer of existing windows. and pull out of the frame. The jamb liner material may come out of the frame when pulling the sash out. E. Remove any and all jamb liner material. Some liners may have frame attachment fasteners that will need to be removed before the liners can be removed. Caution: Spring loaded balances can cause injury; use care when removing balances from existing windows.
11 11 OPENING PREPARATION A. Inspect the existing window frame and repair or replace any defective or rotted wood parts. B. Clean the opening of any dirt, debris, or excess old paint before proceeding. C. Apply one piece of sill flashing tape to the sill of the existing window. Cut the tape the same length as the width of the existing window sill. Place one side of the tape against the vertical leg of the stool, and work the tape into the corner before applying to the sill. Press down firmly. The tape will not cover the sill depth completely under the new window. 11C Note: If needed, blocking/shims may need to be placed where the existing balances were located. Return to Step 3. INSTALLATION INSTRUCTIONS (HEAD EXPANDER) Note: To determine if the Head Expander is required refer to Step 4B. A. Make a pencil mark window on the room side edge of each jamb. B. Install the head expander on the top of the window frame. Slide the expander down onto the head as far as it will go. C. Test fit the window into the opening. Slide the head expander up until the top of the head expander is within Ensure the pencil marks are not visible. If the pencil mark is visible, the expander is extended too far. Note: If the expander extends past the pencil mark it may be necessary to shim the original sill or to order a larger window. Note: The void between the window frame and head expander can be filled with loose-fill insulation. D. Drill two 1/16" pilot holes through the room side leg of head expander into the frame. each hole. Proceed to Step 4D.
12 CLEANING INSTRUCTIONS Be sure to remove all liquid by wiping dry or use a clean squeegee. The vinyl frame may be or Soft scrub may be used. Do not use solvents such as mineral spirits, toluene, xylene, naphtha or muriatic acid as they can dull the finish, soften the vinyl and/or cause failure of the insulated unit seal. Keep door tracks clear of dirt and debris. Keep weep holes open and clear of obstructions. IMPORTANT NOTICE Because all construction must anticipate some water infiltration, it is important that the wall system be designed and constructed to properly manage moisture. Pella Corporation is not responsible for claims or damages caused by anticipated and unanticipated water infiltration; deficiencies in building design, construction and maintenance; failure to install Pella products in accordance with Pella s installation instructions; or the use of Pella products in wall systems which do not allow for proper management of moisture within the wall systems. The determination of the suitability of all building components, including the use of Pella products, as well as the design and installation of installer, or other construction professional and are not the responsibility of Pella. Pella products should not be used in barrier wall systems which do not allow for proper management of moisture within the wall systems, such as barrier Exterior Insulation and Finish Pella makes no warranty of any kind on and assumes no responsibility for Pella windows and doors installed in barrier wall systems. In the states listed above, the installation of Pella Products in barrier wall or similar systems must be in accordance with Pella s installation instructions. Product modifications that are not approved by Pella Corporation will void the Limited Warranty.
REMEMBER TO USE APPROPRIATE PERSONAL PROTECTIVE EQUIPMENT.
Vinyl Windows and Doors Manufactured by Pella Corporation WINDOW REPLACEMENT INSTRUCTIONS FOR DOUBLE-HUNG VENT REPLACEMENT WINDOWS INTO EXISTING DOUBLE-HUNG FRAME USING FRAME SCREWS FROM THE EXTERIOR Part
More informationVinyl Windows and Doors
Vinyl Windows and Doors Manufactured by Pella Corporation WINDOW REPLACEMENT INSTRUCTIONS FOR SINGLE-HUNG AND SLIDING WINDOWS INTO EXISTING CASEMENT FRAME Part Number: V981203 2009 Pella Corporation USING
More informationINTERIOR. Checkrail. Flashing tape
Pella Corporation 2007 Part Number: 808F0100 INSTALLATION INSTRUCTION - INSTRUCCIONES DE INSTALACION FOR PELLA PRECISION FIT DOUBLE-HUNG VENT WINDOW PARA LA VENTANA DE GUILLOTINA CON HOJA PRACTICABLE PRECISION
More informationVinyl Windows and Doors
Vinyl Windows and Doors Part Number: V983572 2011 Pella Corporation INSTALLATION INSTRUCTION - INSTRUCCIONES DE INSTALACION 350 SERIES REPLACEMENT WINDOW WITH 2-1/4 FLUSH FLANGE Lea las instrucciones en
More informationVinyl Windows and Doors
Vinyl Windows and Doors Manufactured by Pella Corporation Installation Instructions for Replacement of Aluminum Sliding Doors in Hard Coat Stucco Applications. Part Number: V981555 2009 Pella Corporation
More informationWINDOW REPLACEMENT INSTRUCTIONS FOR CASEMENT, DOUBLE-HUNG AND CLAD FRAME WINDOWS USING FRAME SCREWS
WINDOW REPLACEMENT INSTRUCTIONS FOR CASEMENT, DOUBLE-HUNG AND CLAD FRAME WINDOWS USING FRAME SCREWS These instructions were tested developed for replacing windows in wood-frame wall construction systems
More informationVinyl Windows and Doors
Vinyl Windows and Doors Part Number: V983570 2011 Pella Corporation INSTALLATION INSTRUCTION - INSTRUCCIONES DE INSTALACION 350 SERIES WINDOW WITH NAIL FIN Lea las instrucciones en español en el reverso.
More informationINSTALLATION INSTRUCTION - INSTRUCCIONES DE INSTALACION PELLA PRECISION FIT AND RENOVATION POCKET REPLACEMENT DOUBLE-HUNG VENT WINDOW
2011 Pella Corporation INSTALLATION INSTRUCTION - INSTRUCCIONES DE INSTALACION PELLA PRECISION FIT AND RENOVATION POCKET REPLACEMENT DOUBLE-HUNG VENT WINDOW Part Number: 808F0105 Important! The Pella Replacement
More informationVinyl Windows and Doors Manufactured by Pella Corporation
Vinyl Windows and Doors Manufactured by Pella Corporation Part Number: V981255 2009 Pella Corporation INSTALLATION INSTRUCTION - INSTRUCCIONES DE INSTALACIÓN FOR BOW WINDOWS WITHOUT HEAD AND SEAT BOARD
More informationWINDOW REPLACEMENT INSTRUCTIONS FOR SINGLE-HUNG, DOUBLE-HUNG, CASEMENT, AWNING INTO EXISTING CASEMENT FRAME USING FRAME SCREWS
2009 Pella Corporation Part Number: 80YV0102 WINDOW REPLACEMENT INSTRUCTIONS FOR SINGLE-HUNG, DOUBLE-HUNG,, AWNING INTO EXISTING FRAME USING FRAME SCREWS These instructions were tested and developed for
More informationINSTALLATION INSTRUCTION - INSTRUCCIONES DE INSTALACIÓN FOR CLAD CASEMENT & AWNING WINDOW VENTANA DE DOS HOJAS CON REVESTIMIENTO
2008 Pella Corporation Part Number: 801P0101 INSTALLATION INSTRUCTION - INSTRUCCIONES DE INSTALACIÓN FOR CLAD CASEMENT & AWNING WINDOW VENTANA DE DOS HOJAS CON REVESTIMIENTO Corner Corner Top Fin Corner
More informationINSTALLATION INSTRUCTIONS IMPERVIA (Vent and Fixed) AWNING, CASEMENT, and LARGE AWNING WINDOW WITH FINS
2012 Pella Corporation Part Number: 80WH0101 INSTALLATION INSTRUCTIONS IMPERVIA (Vent and Fixed) AWNING, CASEMENT, and LARGE AWNING WINDOW WITH FINS Installation Instructions for Typical Wood Frame Construction.
More informationINSTALLATION INSTRUCTIONS - INSTRUCCIONES DE INSTALACION FOR HURRICANESHIELD IMPACT-RESISTANT DOUBLE-HUNG, SINGLE-HUNG AND SIMULATED-HUNG
2008 Pella Corporation Part Number: 80ED0101 INSTALLATION INSTRUCTIONS - INSTRUCCIONES DE INSTALACION FOR HURRICANESHIELD IMPACT-RESISTANT DOUBLE-HUNG, SINGLE-HUNG AND SIMULATED-HUNG Instrucciones en español
More informationINSTALLATION INSTRUCTION FOR CLAD BOW WINDOWS WITHOUT HEAD AND SEAT BOARD
2008 Pella Corporation Part Number: 80KG0101 INSTALLATION INSTRUCTION FOR CLAD BOW WINDOWS WITHOUT HEAD AND SEAT BOARD Note: These instructions may be used for all Pella Bow windows that do not have a
More informationINSTALLATION INSTRUCTION INSTRUCCIONES DE INSTALACIÓN FOR CLAD HINGED PATIO DOOR PUERTA DE BISAGRA PARA PATIO
2008 Pella Corporation Part Number: 801V0101 INSTALLATION INSTRUCTION INSTRUCCIONES DE INSTALACIÓN FOR CLAD HINGED PATIO DOOR PUERTA DE BISAGRA PARA PATIO REMEMBER TO USE APPROPRIATE PERSONAL PROTECTIVE
More informationINSTALLATION INSTRUCTIONS - INSTRUCCIONES PARA LA INSTALACIÓN CLAD WINDOWS WITH FLUSH FLANGE
2012 Pella Corporation Part Number: 81CP0101 INSTALLATION INSTRUCTIONS - INSTRUCCIONES PARA LA INSTALACIÓN CLAD WINDOWS WITH FLUSH FLANGE Lea las instrucciones en español en el reverso Installation Instructions
More informationINSTALLATION INSTRUCTION FOR WOOD DOUBLE-HUNG AND CASEMENT WINDOWS USING WOOD BRICKMOULD OR FLAT CASING
2009 Pella Corporation Part Number: 80DZ0101 INSTALLATION INSTRUCTION FOR WOOD DOUBLE-HUNG AND CASEMENT WINDOWS USING WOOD BRICKMOULD OR FLAT CASING Brickmould/Flat Casing Aluminum Head Flashing Corner
More informationINSTALLATION INSTRUCTION - INSTRUCCIONES DE INSTALACION FOR SLIDING PATIO DOOR
Vinyl Windows and Doors Manufactured by Pella Corporation INSTALLATION INSTRUCTION - INSTRUCCIONES DE INSTALACION FOR SLIDING PATIO DOOR Lea las instrucciones en español en el reverso. Installation Instructions
More informationINSTALLATION INSTRUCTIONS DOUBLE-HUNG WINDOW WITH FINS
2012 Pella Corporation INSTALLATION INSTRUCTIONS DOUBLE-HUNG WINDOW WITH FINS Part Number: 802L0105 Installation Instructions for Typical Wood Frame Construction. These instructions were developed tested
More informationINSTALLATION INSTRUCTIONS IMPERVIA SLIDING PATIO DOOR WITH FINS
2008 Pella Corporation Part Number: 803V0101 INSTALLATION INSTRUCTIONS IMPERVIA SLIDING PATIO DOOR WITH FINS Installation Instructions for Typical Wood Frame Construction. These instructions were developed
More informationVinyl Windows Manufactured by VPI Quality Windows
Vinyl Windows Manufactured by VPI Quality Windows Part Number: 531&591 Installation 531 & 591 SERIES SLIDING AND HUNG WINDOW INSTALLATION INSTRUCTIONS Installation Instructions for Typical Construction.
More informationINSTALLATION INSTRUCTION - INSTRUCCIONES DE INSTALACIÓN FOR CLAD SLIDING PATIO DOOR PUERTA CORREDERA PARA PATIO
2008 Pella Corporation Part Number: 801W0103 INSTALLATION INSTRUCTION - INSTRUCCIONES DE INSTALACIÓN FOR CLAD SLIDING PATIO DOOR PUERTA CORREDERA PARA PATIO Corner Fin Corner Door Top Nailing Fin Side
More informationVinyl Windows and Doors Manufactured by VPI Quality Windows
Vinyl Windows and Doors Manufactured by VPI Quality Windows Part Number: 511_Installation ENDURANCE CASEMENT\AWNING\PW INSTALLATION INSTRUCTIONS Installation Instructions for Typical Construction These
More informationINSTALLATION INSTRUCTION - INSTRUCCIONES DE INSTALACIÓN FOR CLAD AWNING, CASEMENT & NON-RECTANGULAR CASEMENT WINDOW
2009 Pella Corporation Part Number: 812W0100 INSTALLATION INSTRUCTION - INSTRUCCIONES DE INSTALACIÓN FOR CLAD AWNING, CASEMENT & NON-RECTANGULAR CASEMENT WINDOW para las Ventanas de madera recubiertas
More informationINSTALLATION INSTRUCTIONS for Custom and Premium Pocket Windows (JII022) IMPORTANT INFORMATION AND GLOSSARY SAFETY AND HANDLING
Thank you for selecting JELD-WEN products. Attached are JELD-WEN s recommended installation instructions for pocket (replacement) double-hung, casement, awning, picture or transom windows, designed to
More informationPlease read thoroughly and understand completely all the steps in this instruction prior to beginning installation.
2011 Pella Corporation Part Number: 81DU0100 INSTALLATION INSTRUCTION - NAIL FIN INSTALLATION BEFORE WEATHER BARRIER AND FRAME SCREW OR CLIP INSTALLATION FOR REPLACEMENT ALUMINUM-CLAD EXTERIOR HINGED PATIO
More informationREMEMBER TO USE APPROPRIATE PERSONAL PROTECTIVE EQUIPMENT.
2011 Pella Corporation Part Number: 818L0100 INSTALLATION INSTRUCTION - INSTRUCCIONES DE INSTALACION CLAD HINGED PATIO DOOR (INCLUDES STANDARD, PERFORMANCE UPGRADE AND HURRICANESHIELD IMPACT RESISTANT
More information8/7/ HP SWING DOOR INSTALLATION INSTRUCTIONS
8/7/17 1200 HP SWING DOOR INSTALLATION INSTRUCTIONS Installation Instructions for Typical Construction These instructions were developed and tested for use with typical construction in a wall system designed
More informationRead guide from beginning to end before starting installation. Read all warnings and cautions during unit installation.
Installation Guide for E-Series/Eagle High-Performance Mullion Windows with LVL Reinforcement and Installed Using Type B Clips Thank you for choosing Andersen. Instructions are for typical, new wood-framed
More informationPicture Window and Welded Dead-Lite (Exterior) Tools: (Not Provided by Manufacturer) Fig Supplies: (Not Provided by Manufacturer) Fig.
Picture Window and Welded Dead-Lite (Exterior) Tools: (Not Provided by Manufacturer) Tape Measure Utility Knife Fig. 0-1 Drill Level Putty Knife Pry bar Square Foam Gun (Optional) Caulk Gun Hammer Safety
More informationINSTALLATION INSTRUCTION SINGLE PANEL, SINGLE PANEL WITH SIDELIGHT COMBINATION AND 20 MINUTE FIRE RATED WOOD FRAME ENTRY DOOR
2011 Pella Corporation Part Number: 818T0101 INSTALLATION INSTRUCTION SINGLE PANEL, SINGLE PANEL WITH SIDELIGHT COMBINATION AND 20 MINUTE FIRE RATED WOOD FRAME ENTRY DOOR Installation Instructions for
More informationCasement/ Casement Picture Pocket Installation (Interior) Tools: (Not Provided by Manufacturer) Fig Supplies: (Not Provided by Manufacturer)
Casement/ Casement Picture Pocket Installation (Interior) Tools: (Not Provided by Manufacturer) Tape Measure Utility Knife Fig. 0-1 Drill Level Putty Knife Pry bar Square Caulk Gun Hammer Safety Glasses
More informationSash Replacement Guide for Andersen 400 Series Tilt-Wash Transom Windows
for Andersen 400 Series Tilt-Wash Transom Windows Read all instructions carefully before attempting this procedure. If you have any questions about your ability to complete this procedure, call Andersen
More informationFlashing Materials. Rough Opening Preparation
Installation Instructions for CertainTeed New Construction Windows Handling vinyl windows CAUTION: Always store vinyl windows and doors in an upright position on a slight angle. Never lay them flat or
More informationPELLA INSTALLATION INSTRUCTIONS IMPACT RESISTANT BRICKMOULD AND FLUSH FLANGE WINDOWS
PELLA INSTALLATION INSTRUCTIONS IMPACT RESISTANT BRICKMOULD AND FLUSH FLANGE WINDOWS THE FOLLOWING INSTALLATION METHODS ARE INCLUDED IN THIS BOOKLET: New Construction Installation of Wood Brickmould Windows
More informationPELLA INSTALLATION INSTRUCTIONS - ADVANCED PERFORMANCE Nail Fin, Nail Fin with J-Channel and EnduraClad Exterior Trim with Nail Fin Windows
PELLA INSTALLATION INSTRUCTIONS - ADVANCED PERFORMANCE Nail Fin, Nail Fin with J-Channel and EnduraClad Exterior Trim with Nail Fin Windows THE FOLLOWING INSTALLATION METHODS ARE INCLUDED IN THIS BOOKLET:
More informationHR175 Sash Replacement Kit Installation Instructions
HR175 Sash Replacement Kit Installation Instructions IMPORTANT: Please read before you begin. Weather Shield HR175 Sash Replacement Kits Important: Thoroughly read and follow these instructions, failure
More informationEagle clad double-hung window installation instructions
Eagle clad double-hung window installation instructions These instructions are for typical installation in new typical wood frame wall construction. These instructions and methods are not intended for
More informationInstallation Guide for Andersen 400 Series Tilt-Wash Transom Windows with Stormwatch Protection (PG Upgrade) Manufactured After 2006
for Andersen 400 Series Tilt-Wash Transom Windows with Stormwatch Protection (PG Upgrade) Manufactured After 2006 Thank you for choosing Andersen. Instructions are for typical, new wood-framed wall construction
More informationPella Installation Instructions IMPACT RESISTANT BLOCK FRAME WINDOWS
Pella Installation Instructions IMPACT RESISTANT BLOCK FRAME WINDOWS THE FOLLOWING INSTALLATION METHODS ARE INCLUDED IN THIS BOOKLET: New Construction Installation in Masonry Construction for Block Frame
More informationFixed Upper Sash Replacement Guide for Andersen 400 Series Woodwright Springline Single-Hung Windows
Fixed Upper Sash Replacement Guide for Andersen 400 Series Woodwright Springline Single-Hung Windows Manufactured Between September 2005 and October 2006 Read all instructions carefully before attempting
More informationINSTALLATION INSTRUCTIONS FOR REPLACEMENT FORGENT WOOD GLASTRA WINDOWS RECOMMENDATIONS FOR COMMON INSTALLATION OF ALL REPLACEMENT WINDOWS.
INSTALLATION INSTRUCTIONS FOR REPLACEMENT FORGENT WOOD GLASTRA WINDOWS RECOMMENDATIONS FOR COMMON INSTALLATION OF ALL REPLACEMENT WINDOWS. Installer: DO NOT DISCARD Please leave the Installation Guide
More informationInstallation Guide for E-Series/Eagle Clad Mechanically Fastened Windows
Guide for E-Series/Eagle Clad Mechanically Fastened Windows Thank you for choosing Andersen. Instructions are for typical, new wood-framed wall construction with weather protection in place. Instructions
More informationInstallation Guide. for E-Series/Eagle Clad Hinged Inswing French Door
Installation Guide for E-Series/Eagle Clad Hinged Inswing French Door Thank you for choosing Andersen. Instructions are for typical, new wood-framed wall construction with weather protection in place.
More informationT he Double-Hung Replacement System replaces the sash and balance system of an older double-hung window. The
Double-Hung Replacement System Installation The Pozzi Collection PID001 (12/03) T he Double-Hung Replacement System replaces the sash and balance system of an older double-hung window. The frame of the
More informationINSTALLATION INSTRUCTIONS for Custom and Tradition Plus/W-4500 Pocket Windows (JII022) IMPORTANT INFORMATION AND GLOSSARY
for Custom and Tradition Plus/W-4500 Pocket Windows (JII022) Thank you for selecting JELD-WEN products. Attached are JELD-WEN s recommended installation instructions for Pocket (replacement) Double-Hung,
More informationInstallation Guide for Andersen 400 Series Tilt-Wash Transom and 200 Series Narroline Transom Windows
for Andersen 400 Series Tilt-Wash Transom and 200 Series Narroline Transom Windows Congratulations! You have just purchased one of the many fine Andersen products. Proper assembly, installation and maintenance
More informationPlease read thoroughly and understand completely all the steps in this instruction prior to beginning installation.
2011 Pella Corporation Part Number: 81AK0101 INSTALLATION INSTRUCTION - NAIL FIN INSTALLATION AFTER WEATHER BARRIER AND FRAME SCREW OR CLIP INSTALLATION FOR REPLACEMENT ALUMINUM-CLAD EXTERIOR HINGED PATIO
More informationTools required by installer: Materials required by installer:
Installation Guidelines For Quaker Window Products Vinyl product line (Single Hung, Double Hung, Sliding Window, Fixed Window, Casement, Awning, and Hopper) Installer: Read these instructions completely
More informationVYTEX PREMIUM SLIDING GLASS DOOR. Table of Contents. Precautions and Safety 2. Tools Required...3. Inspect and Prepare Door...4
VYTEX PREMIUM SLIDING GLASS DOOR Table of Contents Precautions and Safety 2 Tools Required...3 Inspect and Prepare Door...4 Hardware and Parts Check List....4 Master Frame Assembly 5 Master Frame Installation..7
More informationMeasuring & Ordering Guide
Measuring & Ordering Guide Replacement Vinyl Windows & Patio Doors that fit by Thermo-Fit custom replacement vinyl windows & patio doors by Thermo-Tech are designed to fit your lifestyle for low-maintenance
More informationInstallation Guidelines For Quaker Window Products Aluminum flange fin sub sill & receptor system using a T mulled twin window unit.
Installation Guidelines For Quaker Window Products Aluminum flange fin sub sill & receptor system using a T mulled twin window unit. Installer: Read these instructions completely before starting any installation.
More informationInstallation Instructions Double-Hung, Single-Hung, Casement, Awning, Sliding, Picture & Shapes Non-Impact & Impact Resistant Nailing Fin Windows
Installation Instructions Double-Hung, Single-Hung, Casement, Awning, Sliding, Picture & Shapes Non-Impact & Impact Resistant Nailing Fin Windows americancraftsmanwindows.com Project Requirements: Read
More informationInstallation Guidelines For ALUMINUM M-SERIES 3 PANEL SLIDING DOOR
www.quakerwindows.comv www.quakercommercialwindows.com PO Box 128 504 Highway 63 South Freeburg, MO 65035 800-347-0438 573-469-4151 (fax) Installation Guidelines For ALUMINUM M-SERIES 3 PANEL SLIDING DOOR
More informationCLAD HINGED PATIO DOORS WITH FLUSH FLANGE
2011 Pella Corporation Part Number: 81CL0100 INSTALLATION INSTUCTIONS - INSTUCCIONES DE INSTALACION CLAD HINGED PATIO DOOS WITH FLUSH FLANGE Lea las instrucciones en español en el reverso Installation
More informationWOOD OUT SWING AWNING, CASEMENT, & HOPPER WINDOW
WOOD OUT SWING AWNING, CASEMENT, & HOPPER WINDOW INSTALLATION GUIDE READ SPECIFIC INSTALLATION INSTRUCTIONS COMPLETELY BEFORE STARTING ANY INSTALLATION Failure to install and maintain our product according
More informationPocket Door Installation Instructions
Installation Instructions Before getting started: Read instructions thoroughly. Be sure that you have the necessary tools and materials before starting the installation. Consult your local building code
More informationInstallation Guide. for Andersen 400 Series Tilt-Wash Picture Windows with Stormwatch Protection (High-Performance Impact Resistant Glass)
for Andersen 400 Series Tilt-Wash Picture Windows with Stormwatch Protection (High-Performance Impact Resistant Glass) Installation Guide Congratulations! You have just purchased one of the many fine Andersen
More informationINSTALLATION GUIDE WOOD PIVOTING CIRCLE/ OVAL
WOOD PIVOTING CIRCLE/ OVAL READ SPECIFIC INSTALLATION INSTRUCTIONS COMPLETELY BEFORE STARTING ANY INSTALLATION Failure to install and maintain our product according to these instructions will VOID any
More informationSTACKING MULTI-SLIDE DOOR SYSTEM INSTALLATION INSTRUCTIONS
STACKING MULTI-SLIDE DOOR SYSTEM INSTALLATION INSTRUCTIONS 1290363 Revision 1 12/16 Page 1 Weather Shield Mfg., Inc. NOTICE CAUTION! Failure to install and maintain our product according to these instructions
More informationSash Replacement Guide for Andersen Impact Resistant Casement Windows
Replacement Guide Replacement Guide for Andersen Impact Resistant Casement Windows Congratulations! You have just purchased one of the many fine Andersen products. Proper assembly, installation and maintenance
More informationBlock Frame Inovo Patio Door/Transom/Sidelite Field Mulling Instructions. simonton.com/installation. If mulling sidelites, skip to Step 5.
Effective Date: 10/1/17 Tools Needed Kit Contents Safety Glasses Cordless Drill Phillips Screw Bit Two-step Drill Bit (3/8-1/8 ) Utility Knife Interior Mullion Exterior Mullion Cover Hardware Kit Clamps
More informationInstallation Recommendations for Finless Frame Doors
Installation Recommendations for Finless Frame Doors These installation recommendations are made available by MI Windows and Doors, LLC (MI) to assist with the integration of finless or flange sliding
More informationFOLDING DOOR - FOR FACTORY ASSEMBLED JAMBS WITH APPLIED SILL
FOLDING DOOR - FOR FACTORY ASSEMBLED JAMBS WITH APPLIED SILL READ SPECIFIC INSTALLATION INSTRUCTIONS COMPLETELY BEFORE STARTING ANY INSTALLATION Failure to install and maintain our product according to
More informationInstallation Guide for Architectural Wood Hinged Windows
Guide for Architectural Wood Hinged Windows Congratulations! You have just purchased one of the many fine Andersen products. Proper assembly, installation and maintenance are essential if the benefits
More informationTransom Joining. for Andersen Elliptical Windows over Perma-Shield Gliding Patio Door
Transom Joining for Andersen Elliptical Windows over Perma-Shield Gliding Patio Door INSTALLER: Please leave this guide with the building owner to file for future reference. Congratulations! You have just
More informationSliding Glass Door Assembly and Installation Guide
Sliding Glass Door Assembly and Installation Guide Index Door System Components and Hardware The following components are needed to complete the installation of your Sliding Patio Door unit. Check all
More informationInstallation Guidelines. Next Dimension. Single Hung / Single Hung Fixed / Double Hung / Sliding Window / Fixed Window
Installation Guidelines Next Dimension Single Hung / Single Hung Fixed / Double Hung / Sliding Window / Fixed Window Windsor Windows & Doors Windsor Windows & Doors 900 S. 19 th St. 2210 Stafford St. Extn
More informationINSTALLATION INSTRUCTIONS for Wood/Clad Wood Windows without Exterior Trim or Nailing Fin (JII025) ImpOrTaNT INFOrmaTION & GlOssary.
for Wood/Clad Wood Windows without Exterior Trim or Nailing Fin (JII025) Thank you for selecting JELD -WEN products. Attached are JELD-WEN s recommended installation instructions for metal clad wood windows
More informationPanel Assembly and Installation
Assembly and Installation Assembly and Installation for Andersen 400 Series Frenchwood, 200 Series Narroline, 200 Series Perma-Shield Gliding Patio Doors and 400 Series Perma-Shield Gliding Patio Doors
More information3-LITE PATIO DOOR INSTALLATION INSTRUCTIONS
3-LITE PATIO DOOR INSTALLATION INSTRUCTIONS IMPORTANT: Read the instructions and familiarize yourself with the door parts and pieces before beginning assembly and installation. TOOLS NEEDED: Tape Measure
More informationSeries 7650 Installation Instructions Sliding Glass Door
Series 7650 Installation Instructions Sliding Glass Door Things to Know Before You Start Things to Know Before You Start Removal of Old Fenestration Products Ensure any old fenestration products are removed
More informationMira Premium Series Bi-Parting French Sliding Patio Door Installation Instructions
PREMIUM SERIES W I N D O W S Mira Premium Series Bi-Parting French Sliding Recommended Tools & Accessories Tape Measure Level (3 or longer) Hammer Power Screwdriver Load bearing Shims Flashing (recommended)
More information4-lite Patio Door. Installation Instructions
4-lite Patio Door Installation Instructions IMPORTANT: Read the instructions and familiarize yourself with the door parts and pieces before beginning assembly and installation. Note: Only the 5-0 x 6-8
More informationInstallation of Fiberglass Windows
Installation of Fiberglass Windows Before you begin please read and understand these installation instructions. The following installation instructions are recommended by Norwood and failure to follow
More informationPella Installation Instructions BLOCK FRAME HINGED DOORS
Pella Installation Instructions BLOCK FRAME HINGED DOORS THE FOLLOWING INSTALLATION METHODS ARE INCLUDED IN THIS BOOKLET: New Construction Installation in Masonry Construction for Block Frame Hinged Doors
More informationInstallation Guide for Andersen 200 Series Tilt-Wash Picture, Transom and Circle Top Windows
for Andersen 200 Series Tilt-Wash Picture, Transom and Circle Top Windows Congratulations! You have just purchased one of the many fine Andersen products. Proper assembly, installation and maintenance
More informationNon-Reinforced Joining Guide (Horizontal/Vertical)
Non-Reinforced Joining Guide (Horizontal/Vertical) for Andersen Casement, Awning, and Picture Windows Congratulations! You have just purchased one of the many fine Andersen products. Proper assembly, installation
More informationInstallation Guide for Andersen Frenchwood Patio Door Sidelights and Transoms
for Andersen Frenchwood Patio Door Sidelights and Transoms Congratulations! You have just purchased one of the many fine Andersen products. Proper assembly, installation and maintenance are essential if
More informationwestern window systems westernwindowsystems.com installation instructions non-pocket 2-1/4 panels
series 2600 multi-slide non-pocket 2-1/4 panels windowsystems.com windowsystems.com movement, which can cause warping and other problems. Frame kit components: Each door will have a head assembly, a threshold
More information4. Partially open the operating panel and tilt the top toward the interior of the door (Figure 4). Lift the panel off the sill and set it aside.
Effective Date: 10/1/2017 Tools Needed Kit Contents Hardware Kit Safety Glasses Cordless drill Phillips screw bit Two-step drill bit (3/8-1/8 ) utility knife Interior Mullion Exterior Mullion Cover clamps
More informationINSTALLATION INSTRUCTIONS FOR FORGENT SLIDING PATIO DOORS RECOMMENDATIONS FOR COMMON INSTALLATION OF SLIDING PATIO DOORS.
INSTALLATION INSTRUCTIONS FOR FORGENT SLIDING PATIO DOORS RECOMMENDATIONS FOR COMMON INSTALLATION OF SLIDING PATIO DOORS. Installer: DO NOT DISCARD Please leave the Installation Guide with the home owner
More informationSteel Reinforced Joining Thank you for choosing Andersen. Please leave this guide with building owner.
Steel Reinforced Joining (Horizontal/Vertical) for Andersen 400 Series Woodwright & Tilt-Wash Double-Hung, Picture, and Transom Windows and 400 Series Double-Hung Half Circle and Flexiframe Specialty Windows
More information3/4" LVL Reinforced Joining Guide
(2-Way Horizontal and Vertical Joining) for Andersen 400 Series Tilt-Wash Double-Hung, Picture, and Transom Windows with Stormwatch Protection Congratulations! You have just purchased one of the many fine
More informationfor Andersen 400 Series Woodwright Transom over 400 Series Woodwright Double-Hung or 400 Series Woodwright Picture Window
for Andersen 400 Series Woodwright Transom over 400 Series Woodwright Double-Hung or 400 Series Woodwright Picture Window Congratulations! You have just purchased one of the many fine Andersen products.
More informationInStallatIon InStruCtIonS for vinyl 2-lIte PatIo door assembled
InStallatIon InStruCtIonS for vinyl -lite PatIo door assembled tools & materials you Will need: Measuring Tape Pencil Shims Square Hammer or Mallet Level Drill & Drill bits: 6", 8", 5 6", 7 6" Utility
More informationSun Windows General Information New Construction Sliding Door Installation Instructions H F
A G B D C H F H E H A. Apply Weather Resistive Barrier B. Apply Bottom Flashing Tape C. Install Sill Pan End Caps & Pan D. Caulk Sides & Top Nailing Surface, Set Door, Fasten E. Apply Side Flashing Tape
More informationMetal & Vinyl, Flush Mount and Recessed Fin Windows Recommended Installation Instructions
PO Box 480 Ph: 417-235-7821 Monett, MO 65708 Fax: 417-737-7140 Metal & Vinyl, Flush Mount and Recessed Fin Windows Recommended Installation Instructions These installation instructions are recommendations
More informationNon-Reinforced Joining Guide (2-Way Horizontal and Vertical Joining) for Andersen 200 Series Tilt-Wash Double-Hung and Transom Windows
(2-Way Horizontal and Vertical Joining) for Andersen 200 Series Tilt-Wash Double-Hung and Transom Windows Congratulations! You have just purchased one of the many fine Andersen products. Proper assembly,
More informationINSTALLATION INSTRUCTIONS for Vinyl Projecting Windows with Integral Nailing Fin (JII023)
Thank you for selecting JELD-WEN products. Attached are JELD-WEN s recommended installation instructions for vinyl bay, bow and garden windows which incorporate an integral nailing fin. While the use of
More informationAluminum Clad Wood Window Field Mulling and Stacking Instructions
Aluminum Clad Wood Window Field Mulling and Stacking Instructions Mulling Stacking Mulling and Stacking IMPORTANT: Please read before you begin. TABLE OF CONTENTS AND TOOL / MATERIAL REQUIREMENTS START
More informationVINYL WINDOWS (new construction or replacement) page 2. VINYL PATIO DOORS pages WOOD CLAD WINDOWS (new construction).page 5 WOOD CLAD WINDOWS
RECOMMENDED INSTALLATION INSTRUCTIONS Please choose the appropriate instructions for the product(s) you are using. Read the instructions thoroughly before beginning the installation process. All instructions
More informationFULL FRAME REMOVAL WHEN PREPARING TO INSTALL NEW BLOCK FRAME HINGED DOOR
FULL FRAME REMOVAL WHEN PREPARING TO INSTALL NEW BLOCK FRAME HINGED DOOR This method of Full Frame Removal involves removing the sash and entire frame of the existing door from the wall. The resulting
More informationINSTALLATION WILL REQUIRE (2) OR MORE PERSONS FOR SAFETY REASONS.
PREPARING FOR HINGED DOOR INSTALLATION WITH WOOD BRICKMOULD OR ENDURACLAD EXTERIOR TRIM FOR REPLACEMENT YOU WILL NEED TO SUPPLY: Moisture resistant shims/spacers (12 to 20) 2" galvanized roofing nails
More informationSTACKING MULTI-SLIDE DOOR SYSTEM
SMSD STACKING MULTI-SLIDE DOOR SYSTEM INSTALLATION INSTRUCTIONS READ THESE INSTRUCTIONS COMPLETELY BEFORE STARTING ANY INSTALLATION! CAUTION Lead-based paint may be present in older homes, and the removal
More informationINOVO 2-LITE SLIDING PATIO DOOR
INOVO 2-LITE SLIDING PATIO DOOR ASSEMBLY AND INSTALLATION INSTRUCTIONS IMPORTANT: READ THE INSTRUCTIONS AND FAMILIARIZE YOURSELF WITH THE DOOR PARTS AND PIECES BEFORE BEGINNING ASSEMBLY AND INSTALLATION.
More informationULTRA WINDOW & DOOR EXPANDERS AND RECEIVERS INSTALLATION INSTRUCTIONS
ULTRA WINDOW & DOOR S AND RECEIVERS INSTALLATION INSTRUCTIONS! CAUTION: *REMEMBER SAFETY FIRST* Proper Eye and! Hearing Protection must always be worn during installation of all window and door products.
More informationSun Windows General Information New Construction Hinged Door Installation Instructions
A G H F H H A. Apply Weather Resistive Barrier B. Apply Bottom Flashing Tape C. Install Sill Pan End Caps & Pan D. Caulk Sides & Top Nailing Surface, Set Door, Fasten E. Apply Side Flashing Tape F. Apply
More informationSeries 7600 Installation Instructions Aluminum Multi-Slide Door (Pocketing)
Series 7600 Installation Instructions Aluminum Multi-Slide Door (Pocketing) Things to Know Before You Start Things to Know Before You Start Removal of Old Fenestration Products Ensure any old fenestration
More informationV INSTALLATION INSTRUCTION - INSTRUCCIONES DE INSTALACION 350 SERIES SLIDING PATIO DOOR WITH PANELS SHIPPED OUT OF FRAME
Vinyl Windows and Doors V985940 Part Number: V985940 2010 Pella Corporation INSTLLTION INSTRUCTION - INSTRUCCIONES DE INSTLCION 350 SERIES SLIDING PTIO DOOR WITH PNELS SHIPPED OUT OF FRME Lea las instrucciones
More information