ACCESSIBLE SHOWERING SOLUTIONS. Easa Technical Collection. Essence Shower Doors

Transcription

1 AESSIBLE SHOWERING SOLUTIONS Easa Technical ollection Essence Shower Doors

2 Essence ollection We believe that everybody without exception should benefit from functional, strong and dependable accessible showering solutions, it is from this belief that we created the Essence ollection. The lifetime antibacterial properties of the aluminium frame and plastic parts are innovative and a highly functional addition to this solid and dependable accessible showering option. Frost orner Entry Bi-Fold Doors. Wet Room Easa Dek vinyl installation with Frost orner Entry Bi-Fold Doors. The original Easa product The Essence of what we do Perhaps one of the main reasons for the continued popularity of the Essence range after years on the market, has been the continual refinement of the product following advice and feedback from customers and healthcare professionals. Its strength and versatility comes from our engineering ability to adapt the product, always staying at the forefront of the international accessible shower market. 1. HANDLE/GRIP: The grip provides comfort to the ergonomic and easy to use handles as well as offering a soft grey colour contrast (optional blue colour for those with visual difficulties). 2. MAGNETI LOSURES: Strong magnetic strips and durable water seals enhance the opening and closing functions. 3. LOKING HANDLE (OPEN): Our uniquely designed handle allows those with reduced mobility to easily open and close the doors. 4. LOKING HANDLE (LOSED): In this position, the handle operates as a key locking feature and has no sharp edges. REYLABLE PRODUTS Designed and Made in the UK EASA ANTIBATERIAL PROTETION 5. RISE & FALL HINGE SYSTEM: The 180 rise & fall hinge is bi-directional and rises when opening in either direction, preventing drag across the floor. The doors are spring loaded for smooth action and lock into position when fully open.

3 Design Features & & WATER SEALS: Triple dam bottom seals with incorporated water deflection flippers provide better water retention and a unique water seal which is superior to commonly used systems. 7. FULL HEIGHT POLE: Optional ceiling mounted full height 2.4m (special heights available) curtain support pole. 8. URTAINS: White weighted 2m drop as a standard. Available in 2m and 2.4m widths (depending on enclosure size). Durable polyester. urtains can be easily washed. 11. ESSENE FROST: ontemporary white finish with lightweight polycarbonate panels, stronger than any other commonly used panel material in the market, meeting ISO harpy impact test method. 12. LIFETIME ANTIBATERIAL PROTETION: We use an antibacterial agent in the metal frame coating and all of the plastic parts. This reduces the risk of harmful bacteria including MRSA. 9. URTAIN RAILS: Rails available in White. 10. OMPENSATORS: Standard compensators allow adjustment of +/- 11.5mm. Standard compensators depth 36mm.

4 Essence Portable Doors Designed purposely as a water splash protector to keep the carer or a parent with a child dry during assisted showering. Essence Portable Doors can be folded for easy storage when not in use, are lightweight and suitable for travelling. an be used with any Easa Dek or Tray. Folds easily for storage when not in use. Handles included for ease of carrying. Keeps carer or parent with a child dry during showering. Lightweight and portable, suited for travelling. Available in White frost finish. Available in 2 panel 750x750mm, 3 panel 500x1000x500mm or 4 panel 500x500x500x500mm, height 760mm. Special configurations available on request. Product ode Description Size Finish ESPS002FW 2-Panel Portable Door - White 750x750mm Frost ESPS001FW 3-Panel Portable Door - White 500x1000x500mm Frost ESPS003FW 4-Panel Portable Door - White 500x500x500x500mm Frost 3-Panel Portable Door in a White Frost Finish 500x1000x500mm. Essence Doors Accessories URTAIN RAILS AND URTAINS Product ode AEV AEV AEV Description BENDY URTAIN RAILS Bendy White urtain Rail URTAINS * Standard White urtain 2m wide Optional White urtain 2.4m wide Size 3m Width & Drop 2x2m 2.4x2mm * urtains are plain white polyester and can be easily washed. FULL HEIGHT POLE Product ode AES Description Optional Full Height Pole 2.4m* - white Height 2400mm * Optional Full Height Pole can only be installed on Fixed Panels (not included).

5 Essence ollection Door configurations Saloon Entry SALOON UNI-FOLD SALOON BI-FOLD SALOON BI-FOLD w 2F/P FULL HEIGHT POLE OPTIONAL orner Entry /E BI-FOLD /E BI-FOLD TO SUIT LEFT-HAND TRAY /E BI-FOLD TO SUIT RIGHT-HAND TRAY /E BI-FOLD w F/P TO SUIT LEFT-HAND TRAY /E BI-FOLD & UNI-FOLD TO SUIT LEFT-HAND TRAY TRI-FOLD w F/P TO SUIT LEFT-HAND TRAY FULL HEIGHT POLE OPTIONAL FULL HEIGHT POLE OPTIONAL /E BI-FOLD w F/P TO SUIT RIGHT-HAND TRAY /E BI-FOLD & UNI-FOLD TO SUIT RIGHT-HAND TRAY TRI-FOLD w F/P TO SUIT RIGHT-HAND TRAY FULL HEIGHT POLE OPTIONAL FULL HEIGHT POLE OPTIONAL

6 DEK - 22mm thick fitted below vinyl or tiles 242mm 267mm 317mm 267mm 317mm 900mm 392mm 1050mm 477mm 517mm 1300mm 567mm 1400mm 617mm 1500mm 717mm 1700mm 900mm 317mm 900mm 1050mm 750mm 392mm 477mm Ess TO SUIT TRAY SIZE: (shower area is shown in brackets) 1700x750mm (1650x700mm) 1500x (1450x750mm) mm (1350x850mm) 1300 (1250x750mm) 1220x (1170x1170mm mm (1000x1000mm) 900x900mm (850x850mm) DEK DEK DEK DEK DEK DEK DEK WF: ESS WF: ESS WF: ESS SALOON UNI-FOLD WF: ESS WF: ESS WF: ESS WF: ESS WF: ESS WF: ESS SALOON BI-FOLD WF: ESS WF: ES WF: ES WF: ES WF: ES13008L/R WF: ES15008L/R WF: ES14014L/R WF: ES13014L/R WF: DEK1500/ WF:DEK1400/ WF: DEK1300/ WF: DEK1220/ WF: DEK1050/ STEP IN - tray & trap fitted above floor (80mm high) VISIBLE PIPEWORK 1200mm 750mm 1350mm R 750mm L 720mm L 720mm Essence ollection R 1350mm ONEALED PIPEWORK R 1200mm 1220x720mm L/R (1180x680mm) 1350x750mm L/R (1310x710mm) 1200x L/R (1160x760mm) SI720LTW SI720RTW SI750LTW SI750RTW SI800LTW SI800RTW WF: SI750/ E KEY WF: White with Frost (Polycarbonate) Panels L or R: To suit Left or Right hand Tray WF:LA720/ E WF: LA800/ E WF: LA720/ TF WF: SI750/ TF WF: LA800/ TF en SALOON UNIFOLD w 2F/P /E BI-FOLD NON HANDED /E BI-FOLD TO SUIT RIGHT/LEFTHAND TRAY /E BI-FOLD w F/P TO SUIT RIGHT/LEFTHAND TRAY /E BI-FOLD & UNI-FOLD TO SUIT RIGHT/LEFTHAND TRAY TRI-FOLD w F/P TO SUIT RIGHT/LEFTHAND TRAY ONEALED PIPEWORK Door Height: 760mm Fixed Panel Height: 780mm Handles Height: 805mm Wastes see page 42 Full Height Poles see page 56 ombi Tray Accessories see pages Accessories see pages & 56 /E: orner Entry F/P: Fixed Panel 2F/P: 2 Fixed Panels TO SUIT TRAY SIZE: (shower area is shown in brackets) /E: orner Entry F/P: Fixed Panel /E BI-FOLD NON HANDED /E BI-FOLD w F/P TO SUIT RIGHT/ LEFT-HAND TRAY /E UNI-FOLD w F/P & BI-FOLD TO SUIT RIGHT/LEFT-HAND TRAY : ustomised door option available 6 You need to specify the hand of tray for these codes TRI-FOLD w F/P TO SUIT RIGHT/LEFTHAND TRAY

7 OMBI - install barrier free (0mm) or surface mounted (32mm) 470mm 435mm 485mm 420mm 315mm 315mm 900mm 1050mm 365mm 900mm 455mm 1050mm 355mm 1000mm 355mm 1200mm 355mm 1200mm 355mm 1200mm 355mm 1300mm 355mm 1700mm 1710mm 1400mm 355mm 305mm 355mm 1820mm 710mm 900mm 700mm 365mm 455mm 485mm 700mm 820mm 435mm 485mm 535mm 435mm 700mm 1820x820mm 1710x710mm 1700x mm 1300x700mm 1200x900mm (1780 (1670 (1660 ( (1160 x780mm) x670mm) x760mm) x660mm) x660mm) x860mm) 1200x 1200x700mm 1000 (1160 (1160 (960 x760mm) x660mm) x760mm) mm (1010 x1010mm) 900x900mm (860 x860mm) 800x (760 x760mm) OM OM OM OM OM OM OM OM OM OM OM OM WF: ESS WF: ESS WF: ESS WF: ESS WF: ESS WF: ESS WF: ESS WF: ESS WF: ESS WF: ESS WF: ESS WF: ESS WF: ESS WF: ESS WF: ESS WF: ESS WF: ES WF: ES WF: ESS WF: ES10005L/R WF: ESS WF: ESS nc WF: ES01411L/R WF: ES01311L/R WF: ES012035L/R WF: ES12023L/R WF: ES12011L/R WF: ES01405L/R WF: ES01305L/R WF: ES012029L/R WF: ES12017L/R WF: ES12005L/R WF: OM147/ WF: OM137/ (L/R )TF WF: OM129/ WF: LA800/ WF: OM127/ WF: OM108/ WF: LA1050/ e LEVEL AESS - low level access (5mm threshold) WF: LA865/ E WF: LA865/ TF 430mm LA770/LTW LA770/RTW 900mm LA800/LTW LA800/RTW 480mm LA865/LTW LA865/RTW 970mm 1220x770mm L/R ( mm) 970mm 900mm 1020mm mm mm L/R (1180x680mm) (1180x680mm) mm L/R (980x680mm) mm (1010x1010mm) mm (930930mm) 900x900mm (860x860mm) LA720/LTW LA720/LTW LA720/RTW LA720/RTW LA720S/LTW LA720S/RTW LA1050/TW LA970/TW LA900/TW WF: LA1050/E WF: LA970/E WF: LA900/E WF: LA800/ E WF: LA770/ E WF: LA720/ E WF: LA720S/ E WF: LA800/ TF WF: LA770/ TF WF: LA720/ TF WF: LA720S/ TF WF: LA1050/ TF WF: LA970/ TF 1200 L/R (1160x760mm) 1050mm mm L/R (1225x825mm) 495mm 1200mm 305mm 430mm 480mm 495mm 1050mm R 720mm 1265mm 770mm 865mm R L 720mm 1265mm 330mm 865mm 400mm L 305mm

8 Essence ollection Doors Fitting Instructions IMPORTANT: Please be careful not to scuff profiles during fitting. It is recommended to use a pipe and voltage detector to make sure that there are no wires and/or pipes behind the walls or floors where you are going to bore holes. 1. Place enclosure on flat section of tray or wet floor with the wall compensators placed on each end. 2. Mark on the walls the position of the top and sides of the enclosure. 3. Place the wall compensators in position against the marks on the walls. 4. Using a builders level check that the wall compensators are plumb. 5. Mark through slots and drill wall. Fasten compensators with suitable plugs and screws. Where required, the plastic base of the wall compensator can be trimmed along the guideline to suit coved flooring. 6. Place enclosure back into the wall compensators. Adjust enclosure to compensate for out of true walls. 7. When the enclosure is in line check the bottom seal is in contact with the tray to ensure a watertight seal, adjust if necessary. 8. Bore through the sides of the wall compensators using a 3.5mm diameter drill. Easa UK & Ireland - Tel: +44 (0) Fax: +44 (0) info@easagroup.com Website:

9 Essence ollection Doors Fitting Instructions IMPORTANT: Please be careful not to scuff profiles during fitting. It is recommended to use a pipe and voltage detector to make sure that there are no wires and/or pipes behind the walls or floors where you are going to bore holes. Fixed panel with a pole a. With the enclosure in-line, mark the position of the spigot onto the tray, then bore a hole using a 4.0mm drill and attach it using the screws provided. Add pole base washer. Apply silicon sealant to the base of all fixed parts. b. Slide the fixed panel onto the spigot and tighten the hexagon screw, then slide the flexible grip back into place. Fixed panel without a pole a. With the enclosure in-line, mark the position of the mounting bracket onto the tray, then bore the two holes using a 3.5mm drill and attach it using the screws provided. Apply silicon sealant to the base of all fixed parts. b. Slide the fixed panel onto the mounting bracket and bore through the sides of the mounting bracket using a 3.5mm diameter drill and attach it using the screws and screw cap covers provided. Easa UK & Ireland - Tel: +44 (0) Fax: +44 (0) info@easagroup.com Website:

10 Essence ollection Doors Fitting Instructions IMPORTANT: Please be careful not to scuff profiles during fitting. It is recommended to use a pipe and voltage detector to make sure that there are no wires and/or pipes behind the walls or floors where you are going to bore holes. 9. Fit self tapping screws & screw cap covers provided to secure the door into place. 10. Apply silicone sealant to base of the rise and fall hinges. 11. Keeping the doors correctly in-line use a 4.0mm drill bit to drill through the guide holes in the rise and fall hinge bases into the tray or wet floor. 12. Fit self tapping screws provided. 13. Apply silicone sealant to both the sides and base of wall compensators. Do not add silicon sealant to the base of the door. Please note: Where fitted, curtains should be located as close to the tray as possible or with a maximum floor to curtain gap of 25mm. Do not point and spray the shower head directly onto the enclosure. Easa UK & Ireland - Tel: +44 (0) Fax: +44 (0) info@easagroup.com Website:

11 Essence Half Height Enclosure Full Height Pole Fitting Instructions Use a pipe and voltage detector to make sure that there are no wires and/or pipes where you are boring holes in the ceiling. 1. Remove and discard the blanking plug from the top of the installed half height fi xed panel. 5. At the top inside face of the fi xed panel, using a screwdriver carefully slide the grip cover strip down to reveal a hexagonal screw. heck that the hexagonal screw is suffi ciently loose and then insert the pole into the top of the fi xed panel. Ensure that the block is kept facing into the shower tray. Tighten the hexagonal screw and slide the grip cover strip back into place. 2. When the pole is to be connected to the ceiling, it is necessary to measure from the top of the fi xed panel to the ceiling. The ceiling end of the pole may need to be cut depending on the ceiling height. Using a suitable tool (hacksaw or similar) cut the pole approximately 10mm less than the taken measurement. 3. When the pole is to be connected to the ceiling, slide the ceiling mounting bracket onto the pole keeping the fl anged end uppermost until it is level with the top of the pole. 6. heck the plumb in both directions with a builders level and mark the position of the pole on the curtain rail. 4. Remove and keep the screw from the block that attaches the curtain rail to the pole. Easa UK & Ireland - Tel: +44 (0) Fax: +44 (0) info@easagroup.com Website:

12 Essence Half Height Enclosure Full Height Pole Fitting Instructions Use a pipe and voltage detector to make sure that there are no wires and/or pipes where you are boring holes in the ceiling. 7. Remove curtain cover strip from the top channel of the curtain rail. Using a 3.5mm drill, bore a hole in the centre of the top channel at the position marked. It is necessary to drill a larger hole at the back of the channel only, to accommodate the screw head. 9. When the pole is to be connected to the ceiling, slide the ceiling mounting bracket to be fl ush with the ceiling. heck the plumb in both directions and mark the location of the holes on the ceiling, then bore holes and attach the ceiling mounting bracket to the ceiling using suitable screws. 8. Insert the screw into the hole in the curtain rail through the block into the pole. Replace the curtain cover strip. 10. Tighten the hexagon screw on the side of the ceiling mounting bracket. To ensure a proper ceiling mount it may be necessary to add a bridge between the ceiling joists above the plasterboard and screw the ceiling mounting bracket into it. Easa UK & Ireland - Tel: +44 (0) Fax: +44 (0) info@easagroup.com Website:

13 urtain Rail Fitting Instructions IMPORTANT: Please be careful not to scuff profiles during fitting. It is recommended to use a pipe and voltage detector to make sure that there are no wires and/or pipes behind the walls or ceiling where you are going to bore holes. eiling Riser eiling Mount eiling Riser Screw eiling Riser Mounting Bracket Plastic Wall Plugs lamping Bars lamp Screws eiling Riser Screw urtain Rail Mounting Screws End Stop Glider lip over Strip Glider Glider lip eiling Riser Rail Mount L and U Rails 1. Remove rail and fittings from protective sleeve. 4. Place mounting brackets over ends of rail and offer cut size rail over shower making sure rail is correct distance from floor. Mark around mounting brackets, then screw and fix to wall with screws and wall plugs. 2. Remove cover strip from rail. 5. Place appropriate number of gliders (to suit curtain) into bottom channel and place ceiling riser rail mount into top channel and clamping bars into both channels. 3. Place rail over shower to determine the size required and trim to size with a junior hacksaw. Easa UK & Ireland - Tel: +44 (0) Fax: +44 (0) info@easagroup.com Website:

14 urtain Rail Fitting Instructions IMPORTANT: Please be careful not to scuff profiles during fitting. It is recommended to use a pipe and voltage detector to make sure that there are no wires and/or pipes behind the walls or ceiling where you are going to bore holes. Straight Rails 1. Remove rail and fittings from protective sleeve. 2. Remove cover strip from rail. 7. Place end stop at whichever end the curtain is to rest into bottom of mounting bracket and screw into clamping bar with self tapping screw. 3. After determining the correct distance from the floor and inside wall, mark around mounting brackets, screw and fix to wall with screws and wall plugs. 8. Fix cover strip into top channel. 4. Measure between walls (allowing for faces of mounting brackets) and trim rail to size with a junior hacksaw. 5. Place appropriate number of gliders (to suit curtain) into bottom channel and place clamping bars into both channels. 9. Fix curtain to the end stop and gliders with glider clips. 10. Lubricate the gliding channel with the silicon spray if required. 6. Place rail into mounting brackets and screw into top clamping bars with self tapping screws. Note: For very long straight rails it may be necessary to add ceiling risers. Please follow the notes in L and U rails that describe this procedure. Easa UK & Ireland - Tel: +44 (0) Fax: +44 (0) info@easagroup.com Website:

15 Information and cleaning instructions for your Easa shower doors Please read the following information carefully Product description of Easa doors Your Easa shower doors have been manufactured to provide an environment for you to enjoy a private, partially enclosed showering experience whilst attending to your personal hygiene. A weighted curtain will ensure you can have total privacy if you are able to shower independently. The height of the doors are 760mm and their purpose is to provide privacy and dignity for the user as well as protection for an assistant so they remain dry, and greatly reduces the risk of water leaking onto the bathroom floor. The dimensions and features of the doors vary depending on the showering area & model fitted. Fitting instructions are supplied and contain an illustration of the doors. You should keep these instructions for your reference. leaning instructions / maintenance Essence Range The powder coated surfaces on the Essence shower doors have an antibacterial agent to reduce the risk of cross infection. Essence shower enclosures feature an antibacterial agent in all of the plastic and the textured parts such as the locking handles and hinges. The door panels are manufactured from virtually indestructible polycarbonate. It is important to ensure that a simple cleaning regime is followed to maximise the anti-bacterial agent s effect. After showering, ensure the doors are washed using a damp non-abrasive cloth immersed in warm water containing a mild household detergent. Wipe any excess water, but leave the doors to dry naturally. The anti-bacterial agent works well in a humid environment by migrating to the surface to destroy the bacteria. DO NOT USE: Abrasive cleaners Bleach Hair colorants These products may reduce the life span and the effectiveness of the antibacterial agent and can discolour your shower doors. IMPORTANT The anti-bacterial agent does not replace good cleaning practices. WARNING Never use the shower doors to support your weight when transferring in/out of the shower or to steady or guide you in/out of the shower area. are should be taken when in and around the shower area as wet surfaces increase the risk of slipping. It is advisable that grab rails are installed in the showering area to facilitate safer transfers. If a family member, care worker, home help or privately employed cleaner is responsible for the cleaning of your shower please encourage them to read these instructions. If the doors are used in an environment such as a hospital or nursing home where some clients may have MRSA, it may be necessary to seek additional advice from the Infection ontrol Nurse regarding showering management of clients. Other maintenance information In some cases the bottom enclosure seals may have to be replaced after a period of years. There may be a charge for replacement seals. Warranty* All our doors are manufactured to the highest standard and have a lifetime warranty against manufacturing and material defects. If the unit fails, contact us and quote the serial number that appears on the warranty card and follow the advice detailed in ustomer omplaints Procedure. We will either repair or replace the unit within 14 working days if found to be defective. Please note laims will not be met under guarantee if the product has been abused in any way by neglect, improper use or failure to maintain in accordance with Easa s recommendations, or if the system has been damaged in any accident. The company, when assessing a warranty claim, will also consider abnormal wear and tear. * Please see our Terms and onditions for full details.

16 Our Quality, Safety & Design Assurance E European Union ertifi cates of onformity Easa products have been extensively tested and comply with the following British & European Standards; BS EN 14527:2006 (E) Shower Trays BS EN 14428:2004 (E) Shower Enclosures/Doors EU onstruction Product Directive (89/106/E) BS EN 12600:2002 Glass in building. Pendulum test. Impact test method and classification for flat glass BS EN 274-1:2002 Waste fi ttings EASA W A R R A N T Y Easa Warranties* Easa offers a Lifetime Warranty against manufacturing and material defects, excluding normal wear and tear in general domestic applications. Accessories have a 2 year warranty. * Please see our Terms and onditions for full details. 2 YEAR WARRANTY ON ALL AESSORIES 3D Design and Survey Service Upon request an experienced Easa sales representative can discuss your needs and requirements, and draw a 3D design layout of the bathroom, and provide product technical advice. POLY carbonate Polycarbonate The harpy impact test, also known as the harpy v-notch test, was developed in 1905 by the French scientist Georges harpy. It is a standardized high strain-rate test which determines the amount of energy absorbed by a material during fracture. This absorbed energy is a measure of a given material s toughness and acts as a tool to study temperature-dependent brittle-ductile transition. It is widely applied in industry, since it is easy to prepare and conduct and results can be obtained quickly and more cost-effectively. The values are as follows; MATERIAL HARPY NOTHED ISO 179-1:2010 resistance to impact testing KJ/m 2 POLYARBONATE (used by EASA) >40 PETG 10 PMMA (synthetic polymer of methyl methacrylate) 2 EASA ANTI BATERIAL PROTETION Easa Lifetime Antibacterial System Our lifetime antibacterial protection for ombi trays is based on silver ion technology integrated into the material during manufacture. It cannot be washed away nor reduced by scratches or wearing. It is safe, effective and permanent and is used to protect against bacterial growth, mould and mildew. The material has been tested by an independent microbiological laboratory to the internationally recognised standard JIS Z 2801:2000. The antibacterial effect is rapid and bacterial growth can be inhibited within 2 hours according to laboratory tests. The antibacterial material is not recommended to replace or reduce cleaning procedures but as an additional barrier to bacterial growth. Recyclability REYLABLE PRODUTS All Easa Door collections are fully recyclable. When you buy environmentally friendly products such as our fully recyclable shower trays, you help reduce waste by creating a market for our recycled materials. You also help create jobs in businesses that handle and use recycled materials. Purchasing green products is like making a vote. Requesting more sustainable products in the market place tells manufacturers that consumers care about the way products are made.

17 Other products: Shower Trays The ombi Tray For fl exibility and multi-functionality Shower Floor Formers Wet Room Easa Dek A Resilient, easy to install fl oor former or base concept The Evolution ollection Grab rails Enhancing functionality and Safety Easa N.Ireland (Head Office) Moira Ind Est 34 Old Kilmore Road Moira, o. Armagh N.Ireland BT67 0LZ Tel: +44 (0) Tel from ROI: Fax: +44 (0) Fax from ROI: info@easagroup.com Web: Easa GB (Sub Office) Expressway Works Eastvale Place Yorkhill, Glasgow Scotland G3 8QG Tel: +44 (0) BS EN 14527:2006 (E) Shower Trays BS EN 14428:2004 (E) Shower Enclosures/Doors EU onstruction Product Directive (89/106/E) BS EN 12600:2002 Glass in building. Pendulum test. Impact test method and classifi cation for fl at glass. BS EN 274-1:2002 Waste fi ttings opyright 2012 Easa. All rights reserved. Approved code Office of Fair Trading Designed and Made in the UK REYLABLE PRODUTS TESSDUK0112