PALM PLANER

Transcription

1 PALM PLANER Owner s Manual Rating: Amperes: Blade speed: Planing width: Planing depth: Blade type: Weight: PRODUCT SPECIFICATIONS 120 V 60 Hz AC 3.5 A 13,000 RPM (no load) 2 3/8 (60 mm) maximum 1/64" (.40 mm) to 1/16" (1.5 mm) Reversible 5 lb (2.3 kg) NEED ASSISTANCE? Call us on our toll-free Customer Support Line: Imported by Mastercraft Canada Toronto, Canada M4S 2B8

2 TABLE OF CONTENTS Product specifications.. 1 Table of contents... 2 General safety warnings Eye, ear & lung protection 3 4 Electrical safety. 4 Power tool safety General safety rules.. 5 Work area... 5 Electrical safety. 5 Personal safety Use and care of power tools... 6 Service 6 Specific safety rules.. 7 Extension cord safety... 8 Symbols.. 9 Know your palm planer. 10 Accessories 10 Contents Assembly and operating Adjusting the depth of cut 13 ON/OFF switch with lock-off Planing Blade protection foot. 16 Chamfering Rabbeting Vacuum adaptor 17 Changing the drive belt Replacing the cutting blades Maintenance.. 23 Exploded view 24 Parts list Warranty

3 GENERAL SAFETY WARNINGS! CAUTION: Before using this tool or any of its accessories, read this manual and follow all Safety Rules and Operating Instructions. This instruction manual includes the following: General Safety Rules Specific Safety Rules and Symbols Functional Description Assembly Operation Maintenance Accessories EYE, EAR & LUNG PROTECTION ALWAYS WEAR EYE PROTECTION THAT CONFORMS WITH CSA REQUIREMENTS or ANSI SAFETY STANDARD Z87.1 FLYING DEBRIS can cause permanent eye damage. Prescription eyeglasses ARE NOT a replacement for proper eye protection.! WARNING: Non-compliant eyewear can cause serious injury if broken during the operation of a power tool.! WARNING: Use hearing protection, particularly during extended periods of operation of the tool, or if the operation is noisy. SAVE THESE INSTRUCTIONS FOR REFERENCE 3

4 GENERAL SAFETY WARNINGS WEAR A DUST MASK THAT IS DESIGNED TO BE USED WHEN OPERATING A POWER TOOL IN A DUSTY ENVIRONMENT.! WARNING: Dust that is created by power sanding, sawing, grinding, drilling, and other construction activities may contain chemicals that are known to cause cancer, birth defects, or other genetic abnormalities. These chemicals include: Lead from lead-based paints Crystalline silica from bricks, cement, and other masonry products Arsenic and chromium from chemically treated lumber The level of risk from exposure to these chemicals varies, according to how often this type of work is performed. In order to reduce exposure to these chemicals, work in a well-ventilated area, and use approved safety equipment, such as a dust mask that is specifically designed to filter out microscopic particles. ELECTRICAL SAFETY WARNING: To avoid electrical hazards, fire hazards or damage to the tool, use proper circuit protection. This tool is wired at the factory for V operation. It must be connected to a V, 15-A circuit that is protected by a time-delayed fuse or circuit breaker. To avoid shock or fire, replace power cord immediately if it is worn, cut or damaged in any way. 4

5 POWER TOOL SAFETY GENERAL SAFETY RULES! WARNING: Read and understand all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or serious personal injury. WORK AREA Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents. Do not operate power tools in potentially explosive environments, such as in the presence of flammable liquids, gas or dust. Power tools create sparks that may ignite dust or fumes. Keep bystanders, children and visitors away while operating the tool. Distractions can cause the operator to lose control. ELECTRICAL SAFETY Double insulated tools are equipped with a polarized plug (one blade is wider than the other). This plug will only fit into a polarized plug one way. If the plug does not fit into the outlet properly, reverse the plug. If it still does not fit, contact a qualified electrician to install a polarized outlet. Do not alter the plug in any way. Double insulation eliminates the need for the three-pronged grounded power cord and grounded power supply system. Avoid contact between the operator's body and grounded surfaces such as pipes, radiators, ranges, and refrigerators. There is an increased risk of electric shock if the operator's body is grounded. Do not expose power tools to rain or wet conditions. Water entering the power tool will increase the risk of electric shock. Do not abuse the cord. Do not use the power cord to carry the tool or to pull the plug out of the outlet. Keep the power cord away from heat, oil, sharp edges, and moving parts. Replace a damaged power cord immediately. A damaged power cord increases the risk of electric shock. When operating a power tool outdoors, use an outdoor-rated extension cord type W-A or W. These cords are rated for outdoor use and they reduce the risk of electric shock. PERSONAL SAFETY Stay alert, be aware of the surroundings, and use common sense when operating a power tool. Do not use a power tool while tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating a power tool may result in serious personal injury. Dress properly. Do not wear loose clothing or jewellery. Contain long hair. Keep hair, clothing, and gloves away from moving parts. Loose clothing, jewellery, or long hair can get caught in moving parts. 5

6 POWER TOOL SAFETY PERSONAL SAFETY cont d Avoid accidental start-ups. Verify that the switch is in the OFF position before plugging in the tool. Carrying a power tool with a finger on the switch or plugging in a tool that has the switch in the ON position invites accidents. Remove adjusting keys and wrenches before turning the tool ON. A wrench or key that is left attached to a rotating part of the tool may result in personal injury. Do not overreach. Keep proper footing and balance at all times. Proper footing and balance allows the operator to maintain better control of the tool in unexpected situations. Use safety equipment. Always wear eye protection. Use a dust mask, non-skid safety shoes, a hardhat, or hearing protection when appropriate. USE AND CARE OF POWER TOOLS Use clamps or another practical means to secure and support the workpiece to a stable platform. Holding the work in a hand or against the body is not stable, and may lead to loss of control. Do not force the tool. Use the correct tool for the application. The correct tool will do the job better and safer when used at the rate that it was designed to work at. Do not use a power tool if it cannot be turned ON or OFF using the power switch. A tool that cannot be controlled using the switch is dangerous, and must be repaired. Disconnect the plug from the outlet before making any adjustments, changing accessories, or storing the tool. Such preventive safety measures reduce the risk of accidental start-ups. When power tools are not in use, store them out of the reach of children or untrained persons. Tools are dangerous in the hands of untrained users. Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind, and are easier to control. Inspect the tool for misalignment or binding of moving parts, broken parts, and any other condition that may affect the operation of the tool. If it is damaged, have the tool serviced before using it. Many accidents are caused by poorly maintained tools. Use only accessories that are recommended by the manufacturer for this model. Accessories that are suitable for one tool may become hazardous when used with another tool. SERVICE Tools servicing must be performed by qualified personnel. Service or maintenance performed by non-qualified personnel could result in a risk of injury. When servicing a tool, use only identical replacement parts. Follow the instructions in the Maintenance section of this Manual. The use of unauthorized parts or failure to follow the instructions in the Maintenance section of this Manual may create a risk of electric shock or injury. 6

7 SPECIFIC SAFETY RULES! WARNING: Know your palm planer. Read the Instruction Manual carefully. Learn the tool s applications and limitations, as well as the specific potential hazards related to this tool. Following this rule will reduce the risk of electric shock, fire or serious injury. Always wear eye protection. Any power tool can throw foreign objects into your eyes and cause permanent eye damage. ALWAYS wear safety goggles (not glasses) that comply with ANSI safety standard Z87.1. Everyday glasses have only impact resistant lenses. They ARE NOT safety glasses.! WARNING: Glasses or goggles not in compliance with ANSI Z87.1 could cause serious injury when they break. Always wear hearing protection and a dust mask. Use only in a well-ventilated area. Using personal safety devices and working in a safe environment reduces the risk of injury.! DANGER: Always unplug the tool from the power source before making any adjustments or removing the blades.! DANGER: Be extremely careful when handling the cutting blades. They are extremely sharp and can cause serious injury.! DANGER: Always make sure the blade clamping screws are correctly tightened before using the planer.! DANGER: Use only Mastercraft replacement cutting blades. Any other cutting blades may not be clamped properly in the cylinder and could be violently thrown, causing serious injury to the operator.! DANGER: When turning the planer ON, watch for excessive vibration which could be caused by loose or improperly installed cutting blades. Never use dull or damaged cutting blades. Dull or damaged cutting blades require more power to operate and could result in overheating the motor. They will also result in poor cutting action and a rough finish. Always replace both blades at the same time to maintain proper cylinder balance and smooth cutting action. Always make sure the work surface is free of nails and other foreign objects. Cutting into a nail can cause the tool to jump. It will also damage the cutting blades. Always use a safe method to secure the workpiece. Use both hands to guide the tool wherever possible. Never place hands near the cutting blades. Never lay the workpiece on hard surfaces such as concrete, stone, etc. The tool may jump if the cutting blades contact the hard surface. The blades will also be damaged. Make sure all rags, cords, string etc. are removed from the work area. Any of these items could be caught in the cutting blades and cause loss of control over the tool. Never operate the palm planer while covering the air vents with your hands. The motor will overheat. 7

8 SPECIFIC SAFETY RULES When turning the switch ON, make sure the cutting blades are not touching anything, including the workpiece. Always allow the motor to come up to its full speed before attempting to use the planer. Do not allow your face to get too close to the workpiece when operating the tool. Wood chips can fly onto your face and eyes. Turn the tool OFF and wait for the cutting blades to stop before setting the tool down. Never take deep cuts or move the planer into the workpiece too quickly. Either action will reduce the motor speed and cause the motor to overheat and produce rough cutting action. When setting tool down, either lay it on its side or in its upright position with the blade protection foot resting on a flat surface. Use the dust extraction system wherever practical to avoid creating excessive dust. Never use your finger to remove wood chips and saw dust from the chip chute. If chips and saw dust from damp wood become jammed in the chip chute, turn the tool OFF, unplug it from the power source and use a wooden stick to clean out the chip chute. EXTENSION CORD SAFETY! WARNING: Keep the extension cord clear of the work area. Position the cord so it will not get caught on the workpiece, a tool, or any other obstruction while the power tool is in use. 8 If an extension cord is used with this palm planer, verify that it is in good condition. When using an extension cord, be sure to use one that is heavy enough to carry the current that the tool will draw. An undersized cord will cause a drop in line voltage, which will result in a loss of power and overheating. The following table shows the correct size to use according to cord length and the amperage rating that is listed on the tool's nameplate. When in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord. Verify that the extension cord is properly wired and in good condition. Replace a damaged extension cord immediately, or have it repaired by a qualified electrician before using it. Keep the extension cord away from sharp objects, excessive heat, and damp or wet areas. Use a separate electrical circuit for power tools. This circuit must consist of not less than 14 gauge wire and should be protected by either a 15 A time-delayed fuse or a circuit breaker. Before connecting the power tool to the outlet, verify that the switch is in the OFF position, and that the voltage of the power source is the same as the voltage that is indicated on the tool's nameplate. Running this palm planer at lower voltage will damage the motor. MINIMUM GAUGE (AWG) EXTENSION CORDS (120 V use only) Ampere Rating Total length in feet Not More Than More Than Not Applicable

9 SYMBOLS! WARNING: Some of the following symbols may appear on the palm planer. Study these symbols and learn their meaning. Proper interpretation of these symbols will allow for more efficient and safer operation of this tool. V A Hz W kw L kg H N/cm 2 Pa Min S Volts Amperes Hertz Watts Kilowatts Microfarads Litres Kilograms Hours Newtons per square centimetre Pascals Minutes Seconds Alternating current Three-phase alternating current Three-phase alternating current with neutral Direct current No load speed Alternating or direct current Class II construction Splash-proof construction Watertight construction Protective grounding at grounding terminal, Class I tools Revolutions or reciprocations per minute Diameter Off position Arrow Warning symbol HOMOLOGUÉ This symbol designates that this tool is listed with Canadian requirements by ETL Testing Laboratories, Inc. Conforms to UL STD. 73 Certified to CAN/CSA STD. C22.2 No. 12 9

10 KNOW YOUR PALM PLANER Lock-off Button On/Off switch Main handle Depth adjustment knob Fixed sole plate Moveable sole plate Air vents Drive belt cover ACCESSORIES AVAILABLE ACCESSORIES! WARNING: Use only accessories that are recommended for this palm planer. Follow the instructions that accompany the accessories. The use of improper accessories may result in injury to the operator or damage to the palm planer. Before using any accessory, carefully read the instructions or the Owner s Manual for the accessory. Replacement cutting blades! WARNING: If any part is missing or damaged, do not plug the tool into the power source until the missing or damaged part is replaced. 10

11 CONTENTS CONTENTS Carefully unpack the palm planer. Compare the contents against the PALM PLANER COMPONENTS chart at right. NOTE: See illustration of palm planer on Page 12.! WARNING: To avoid fire or toxic reaction, never use gasoline, naphtha, acetone, lacquer thinner or similar highly volatile solvents to clean the tool. PALM PLANER COMPONENTS KEY DESCRIPTION QTY A Palm planer 1 B 2.5 mm Hex key 1 C Cutting blade wrench 1 D Replacement drive belt 1 E Vacuum adapter 1 F Blow moulded case 1 Owner s manual 1 11

12 CONTENTS 12

13 ADJUSTING THE DEPTH OF CUT The depth of cut can be set anywhere between 1/64 (0.40 mm) and 1/16 (1.5 mm). ASSEMBLY AND OPERATING To set the cutting depth, rotate the depth adjustment knob (1) to the desired cutting depth (Fig. 1). To increase the cutting depth, turn the knob clockwise. To decrease the cutting depth, turn the knob counter clockwise. NOTES: a) When leaving the tool unattended or when storing the tool, set the cutting depth knob to P. This setting will ensure the cutting blades are fully retracted from the sole plate surface. b) The depth indicators on the depth adjustment knob are approximations only. Always make a test cut on a scrap workpiece to verify the correct amount of material is being removed. Fig. 1 ON/OFF SWITCH WITH LOCK-OFF This tool is equipped with an ON/OFF switch and LOCK-OFF button to prevent it from being accidentally started when the ON/OFF switch is pressed. 1. To turn the tool ON, grasp the planer handle with your right hand and slide the lock-off switch (1) forward (Fig. 2). 2. While holding the lock-off switch forward, press the upper portion of the ON/OFF button (2) into the tool handle with your thumb. Fig. 2 13

14 ON/OFF SWITCH WITH LOCK OFF cont d 3. When the tool starts, you can release the lock-off switch while continuing to press inward on the ON/OFF button. The tool will continue to run. 4. To turn the tool OFF, remove your thumb from the ON/OFF button. NOTE: Once the tool has stopped, you must repeat steps 1 & 2 to turn it ON again. ASSEMBLY AND OPERATING! WARNING For safety reasons, the operator must read the sections of this Instruction Manual entitled GENERAL SAFETY WARNINGS, POWER TOOL SAFETY, SPECIFIC SAFETY RULES, EXTENSION CORD SAFETY and SYMBOLS before using this palm planer. Verify the following every time the palm planer is used: 1. Safety glasses, safety goggles, or face shield is being worn. 2. Hearing protection and dust mask are being worn. 3. The cutting blades are in good condition, and are properly tightened into the cylinder. 4. The power cord is clear of the cutting blade path. 5. The workpiece is clear of any foreign materials such as nails. Failure to observe these safety rules will significantly increase the risk of injury. 14

15 ASSEMBLY AND OPERATING PLANING! WARNING: Use two hands on the planer when practical.! WARNING: Where possible, clamp the workpiece to a stable platform such as a work bench. 1. Adjust depth of cut. 2. Rest the front sole plate (1) on the workpiece (2) (Fig. 3). NOTE: Make sure the cutting blades do NOT contact the workpiece. 3. Turn the tool ON and wait for the cutting blades to reach full speed. 4. While holding the tool firmly, slowly move the tool forward while applying slight pressure to the front of the tool. Fig As you near the end of the forward planing stroke, use your right hand to apply slight downward pressure to the rear of the tool. This action will ensure a smooth consistent cutting depth as the cutting blades leave the workpiece. NOTE: Do not allow the front of the planer to tilt downward as the cutting blades leave the workpiece. A deeper cut will result. 6. Push the planer forward until the cutting blades move beyond the workpiece. NOTES: a) For better control of the planer, incline the workpiece slightly away from you so you plane downhill. 15

16 ASSEMBLY AND OPERATING PLANING cont d NOTES: b) Moving the plane too quickly or removing too much material in one pass will result in poor quality of cuts and possibly damage to the motor. It is always better to remove the material in small amounts using more passes to complete the work. c) Moving the planer too slowly may cause the blades to burn or mar the surface. d) The proper feed rate will be dictated by the depth of cut, the type of wood, and the moisture content of the wood being planed. Make practice cuts on a scrap workpiece of the same material as the good workpiece to establish the correct cutting depth and feed rate. BLADE PROTECTION FOOT Between planning operations, you can rest the planer on a flat surface with the blade protection foot (1) in the downward position (Fig. 4). NOTE: The blade protection foot will automatically fall into the down position when the cut is complete and be pushed to its upward position (2) when the planer is moved forward on the workpiece. Fig. 4 CHAMFERING! To chamfer the corner of the workpiece, align one of the three V grooves (1) with the corner of the workpiece (2) (Fig. 5). NOTE: The V grooves are different depths. Select the V groove that will produce the desired chamfer. Fig. 5 16

17 ASSEMBLY AND OPERATING RABBETING 1. Draw a pencil line (1) at the desired depth of the rabbet (Fig. 6). 2. Make the first cut with the right hand edge of the sole plate aligned with the pencil line. 3. Make the next cut with the sole plate sliding along the edge left by the first cut (Fig. 7). Fig Continue making successive cuts until the desired depth of rabbet is achieved. VACUUM ADAPTER The vacuum adapter can be installed for use with a workshop vacuum. 1. Push the small end of the vacuum adapter (1) into the vacuum port (2) located on the right hand side of the palm planer (Fig. 8). Fig. 7 NOTE: Twist the vacuum adapter to ensure the two locking knobs (3) click into the two matching holes (4) in the vacuum port. 2. To remove the vacuum adapter, twist and pull it from the vacuum port of the tool. Fig. 8 CHANGING THE DRIVE BELT After several hours of use, the drive belt may become worn or break.! WARNING: Remove the plug from the power source. 17

18 CHANGING THE DRIVE BELT cont d 1. Turn the tool on its right hand side on a table or work bench.! WARNING: Be extremely careful not to touch the cutting blades with your hands. Serious injury may result. 2. Remove three belt cover screws (1) from the belt cover (2) using a #2 screwdriver (Fig 9). 3. Pull the belt cover away from the planer housing (3). ASSEMBLY AND OPERATING 4. If the belt is broken, remove it from the pulley area. If the belt is NOT broken, insert one finger under the belt (4) about 1 (2.54 cm) from the large drive pulley (5) and pull upward on the belt (Fig. 10). Fig While pulling upward on the belt, pull it toward the large pulley. The belt will climb upward on the pulley as the pulley rotates. 6. Repeat steps #4 & #5 until the belt is completely removed from both pulleys. 7. Remove all loose debris from the belt housing and belt housing cover. Fig. 10 NOTE: Use a clean DRY soft brush. Never use any solvent or water as you will damage the tool. 8. Place the belt on the small pulley (6) (Fig. 11). NOTE: Make sure the belt fits fully into all the grooves in the small pulley. Fig

19 CHANGING THE DRIVE BELT cont d 9. Place the belt on the edge of the large pulley (7). 10. Press downward on the belt about 1 (2.54 cm) from the pulley (8). ASSEMBLY AND OPERATING 11. Rotate the pulley while pressing down on the belt, moving your finger toward the large pulley. 12. Repeat steps #10 & #11 until the belt is fully installed on the large pulley. Fig. 11 NOTE: Once the belt is fully installed on the large pulley, rotate the pulleys and check to make sure the belt is fully engaged in ALL the grooves in BOTH the large and small pulleys. If the belt is not engaging all the grooves, it will damage the tool and the belt will be ruined. 13. Replace the belt cover. Do not over tighten the screws. REPLACING THE CUTTING BLADES! WARNING: Exercise extreme caution when handling the cutting blades. Use small pliers to remove and replace the blades in the blade cylinder.! WARNING: Remove the plug from the power source. Removing the blades 1. Place the tool on its back with the cord end to your left hand side. It is best to place the tool on a work bench that is protected with an old towel to prevent damaging the tool or blades. 19

20 REPLACING THE CUTTING BLADES cont d Removing the blades cont d 2. Rotate the cylinder to expose one of the blades (1) in the middle of the opening between the front and rear sole plates (Fig. 12). ASSEMBLY AND OPERATING 3. Using the 30 mm blade screw wrench (2), loosen all three blade clamp screws (3) approximately 1 turn.! WARNING: Exercise extreme caution when using the wrench on the blade clamp screws. The blade is extremely sharp and may cause serious injury if the wrench slips or you touch the blade. Fig. 12 NOTE: To loosen the blade clamp screws, push the wrench AWAY from your body. 4. Carefully place the blade of a small screwdriver (4) on the end of the blade (5) and carefully and pry the cutting blade away from the metal blade stop (6) (Fig. 13). NOTE: Pry the blade away from the metal stop at least 1/8 (3 mm). 5. Use a small pair of pliers (7) to pull on the exposed end of the cutting blade (8) (Fig. 14). Slide the blade completely out of the blade clamp (9). Fig Use a soft dry brush to clean all debris out of the cutting blade clamp. 7. Repeat steps #2 through #6 to remove the second blade from the blade cylinder. Fig

21 REPLACING THE CUTTING BLADES cont d Installing the cutting blades 1. Rotate the cutting blade endways so the sharp new cutting edge is facing upward. 2. Carefully grasp the far end of the cutting blade with a pair of small pliers and slide the cutting blade, sharp side up, into the cutting blade clamp where the blade was removed. NOTE: Make sure the grooved side of the cutting blade is toward the rear of the tool and the new sharp edge is upward. 3. Use a small piece of scrap wood to gently push the blade fully into the blade clamp until it comes to rest against the metal blade stop. ASSEMBLY AND OPERATING 4. Slightly tighten the MIDDLE blade clamp screw (1) using the 30 mm blade screw wrench (Fig. 15). Fig. 15 NOTE: Tighten the blade clamp screw by pulling the wrench toward you. At this point, only tighten the blade clamp screw SLIGHTLY. 5. Using a small piece of soft wood, carefully tap the ends of the blade to ensure it is exactly parallel with the front sole plate, blade cylinder and blade clamp. NOTE: If the blade is not parallel with the front sole plate, the planning action will not be square. 21

22 REPLACING THE CUTTING BLADES cont d Installing the cutting blades cont d 6. When you have made the cutting blade parallel to the front sole plate, SLIGHTLY tighten the two outer blade clamp screws (2 and 3). 7. Recheck the blade alignment and make any necessary adjustments. ASSEMBLY AND OPERATING 8. Completely tighten the MIDDLE blade clamp screw first, and then completely tighten the two outer blade clamp screws. 9. Recheck the blade alignment to make sure the blade did not move while tightening the blade clamp screws. If the blade requires realignment, repeat steps #4 through #8. Fig Repeat steps #1 through #9 to install the second cutting blade.! DANGER: Make sure all three of the blade clamp screws are fully tightened before turning the tool ON. When turning the tool ON, always have the cutting blades and sole plate facing away from your body. Loose cutting blades will be thrown violently and possibly cause serious injury. 11. Turn the tool ON. If there are any unusual sounds or vibrations, turn the tool OFF immediately and check for misaligned or damaged cutting blades. 22

23 MAINTENANCE GENERAL! WARNING: When servicing, use only identical replacement parts. The use of any other part may create a hazard or cause product damage. DO NOT use solvents when cleaning plastic parts. Plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use. Use a clean cloth to remove dirt, dust, oil, grease etc.! WARNING: Do not allow brake fluids, gasoline, petroleum-based products, penetrating oils, etc. to come into contact with plastic parts. They contain chemicals that can damage, weaken or destroy plastic. DO NOT abuse power tools. Abusive practices can damage the tool and the workpiece.! WARNING: DO NOT attempt to modify tools or create accessories. Any such alteration or modification is misuse and could result in a hazardous condition leading to possible serious injury. It will also void the warranty. LUBRICATION All of the bearings in this tool are lubricated with a sufficient amount of highgrade lubricant for the life of the unit under normal conditions. Therefore, no further lubrication is required. 23

24 EXPLODED VIEW 24

25 PARTS LIST! WARNING: When servicing, use only Mastercraft replacement parts. The use of any other parts may create a safety hazard or cause damage to the palm planer. Any attempt to repair or replace electrical parts on this palm planer may create a safety hazard unless repairs are performed by a qualified technician. For more information, call the Toll-free Helpline, at Always order by PART NUMBER, not by key number. Key # Part # Part Name Quantity Label Left decorative plate Switch button Spring Left housing Safety button spring Safety button spring Flat washer Tapping screw ST 2.9x Switch on/off plate Tapping screw ST 2.9x Terminal Micro switch Front sole plate Depth adjustment spring Guide seat Depth adjustment nut Small copper cap Small spring Depth adjustment knob Spring washer 4x Screw M4x Depth adjustment knob cover Right housing Right decorative plate Flat washer Spring washer Screw M3x Tapping screw ST2.9x Bearing 608RS Dust baffle Mounting plate 2 25

26 PARTS LIST Key # Part # Part Name Quantity Blade roller Hex bolt Blade clamping plate Blade fixing plate Blade Set screw Protection plate Roller shaft Dust sleeve Tapping screw ST3.9x Cord clamp Cord guard Cord set Bearing 6000RS Bearing hold down Tapping screw ST3.9x Belt wheel Hex nut M Belt Belt cover Tapping screw ST3.9x Stator Bearing 607RS Carbon brush Brush holder Brush holder support Rotor Motor gear Hex nut M Motor belt wheel Gearbox Bearing 628RS Output shaft Woodruff key Big gear Retaining ring Gearbox cover Tapping screw ST3.9x Back sole plate Rest foot Dust port Spanner 1 26

27 5-Year Limited Warranty This Mastercraft Maximum product is guaranteed for a period of five (5) years from the date of original retail purchase against defects in workmanship and materials, except for the following components: a) Component A: Batteries, chargers and carrying cases, which are guaranteed for a period of two (2) years from the date of original retail purchase against defects in workmanship and materials; b) Component B: Accessories which are guaranteed for a period of one (1) year from the date of original retail purchase against defects in workmanship and materials. Subject to the conditions and limitations described below, this product, if returned to us with proof of purchase within the stated warranty period and if covered under this warranty, will be repaired or replaced (with the same model, or one of equal value or specification),at our option. We will bear the cost of any repair or replacement and any costs of labour relating thereto. These warranties are subject to the following conditions and limitations: a) A bill of sale verifying the purchase and purchase date must be provided; b) This warranty will not apply to any product or part thereof that is worn or broken or that has become inoperative due to abuse, misuse, accidental damage, neglect or lack of proper installation, operation or maintenance (as outlined in the applicable owner s manual or operating instructions) or that is being used for industrial, professional, commercial or rental purposes; c) This warranty will not apply to normal wear and tear or to expendable parts or accessories that may be supplied with the product that are expected to become inoperative or unusable after a reasonable period of use; d) This warranty will not apply to routine maintenance and consumable items, including but not limited to fuel, lubricants, vacuum bags, blades, belts, sandpaper, bits, fluids, tune-ups or adjustments; e) This warranty will not apply where damage is caused by repairs made or attempted by others (i.e.: persons not authorized by the manufacturer); f) This warranty will not apply to any product that was sold to the original purchaser as a reconditioned or refurbished product (unless otherwise specified in writing); Page 1 of 2 27

28 5-Year Limited Warranty cont d These warranties are subject to the following conditions and limitations: g) This warranty will not apply to any product or part thereof if any part from another manufacturer is installed therein or any repairs or alterations have been made or attempted by unauthorized persons; h) This warranty will not apply to normal deterioration of the exterior finish including but not limited to scratches, dents, paint chips, or to any corrosion or discolouring by heat, abrasive and chemical cleaners; and i) This warranty will not apply to component parts sold by and identified as the product of another company, which shall be covered under the product manufacturer s warranty, if any. Additional Limitations This warranty applies only to the original purchaser, and cannot be transferred. Neither the retailer nor the manufacturer shall be liable for any other expense, loss or damage, including but not limited to any indirect, incidental, consequential or exemplary damages arising in connection with the sale, use or inability to use this product. Notice to Consumer This warranty gives you specific legal rights, and you may have other rights, which may vary from province to province. The provisions contained in this warranty are not intended to limit, modify, take away from, disclaim or exclude any statutory warranties set forth in any applicable provincial or federal legislation. Mastercraft is a superior line of products selected for their workmanship and materials. These products are designed to meet rigorous quality and performance standards, and are approved by our Quality Assurance laboratory. TOLL-FREE HELPLINE: Page 2 of 2 Imported by Mastercraft Canada Toronto, Canada M4S 2B8 Rev /05/