YOW 225 TU Window System
|
|
- Roy Pierce Willis
- 6 years ago
- Views:
Transcription
1 ThermaBond Plus Poured & Debridged Technology YOW 225 TU SYSTEM DESCRIPTION YOW 225 TU PERFORMANCE FEATURES 2-1/4 Overall Depth ThermaBond Plus Poured & Debridged Thermal Break Variations: Casement, Projected Vents, & Fixed Windows 1 & 1/4 Glazing Optional Screens Installation Manual AAMA/NWWDA 101/I.S.2-97 AW-65 Rating (Operable) AW-100 Rating (Fixed) U Value = 0.45 BTU/HR/FT 2 / F CRF of 60 Factory Mitered & Sealed 2004 YKK AP America Inc. is a subsidiary of YKK Corporation of America.
2
3 TABLE OF CONTENTS Installation Notes Page ii & iii INSTALLATION Determine Window Reference Point Page 1 Determine Type of Anchors To Be Used Page 1 & 2 Installation Options and Procedures Page 2 & 3 GLAZING Prep Casement Windows Page 4 Prep Fixed & Projected Windows Page 5 Install Glass Page 6 Calculating Glass Sizes Page 7 & 8 INSTALLATION OPTIONS Install Stacking Mullions Page 9 Page-i
4 INSTALLATION NOTES 1. Do not drop, roll or drag boxes of aluminum framing. Move and stack boxes with proper support to prevent distortion. If fork lifts are used, be especially careful about striking the boxes when lifting or moving. 2. Store in a dry, out of the way area. If rain exposure, condensation or any water contact is likely, then all packaging material should be removed. Wet packaging materials will discolor and may stain aluminum finishes and paints. 3. All materials should be checked for quantity and quality upon receipt, YKK AP must be notified immediately of any discrepancies in shipment. Check to make sure that you have the required shims, sealants, supplies, and tools necessary for the installation. 4. Carefully check the openings and surrounding conditions that will receive your material. Remember, if the construction is not per the construction documents, it is your responsibility to notify the general contractor in writing. Any discrepancies must be brought to the general contractor s attention before you proceed with the installation. 5. Collect your shop drawings, materials, packing list, and this installation manual. Carefully review parts location, the sequence of installation, when you glaze it, and how you seal it. Installation instructions are of a general nature and may not cover every condition you will encounter. The shop drawings and/or installation manuals were prepared specifically for the product. 6. Any material substitutions must be of equal or greater quality. 7. Make certain that material samples have been sent for compatibility testing for all manufacturer s sealants involved. Make certain that sealants have been installed in strict accordance with the manufacturer s recommendations and specifications. 8. Consult sealant manufacture for proper sealant and backer rod selection. 9. Remember to isolate, in a approved manner, all aluminum from uncured masonry or other incompatible materials. 10. System-to-structure fasteners are not supplied by YKK AP. Fasteners called out on shop drawings are to indicate minimum sizes for design loading. 11. If any questions arise concerning YKK AP products or their installation, contact YKK AP for clarification before proceeding. Page-ii
5 INSTALLATION NOTES 12. YKK AP window installation is typically completed before drywall, flooring and other products which may still be in process. Take the extra time to wrap and protect the installed material. 13. Cutting tolerances are plus or minus one thirty second unless otherwise specified. 14. YKK AP Model YOW 225 TU windows are prefinished, prefabricated, and preassembled products, and must be protected against damage. 15.Concrete, mortar, plaster, muriatic acid and other alkaline and acid based construction and cleaning materials may be very harmful to window finishes and should be removed with water and mild soap immediately or permanent damage or staining of the finishes will occur. A spot test is recommended before any cleaning agent is used, and abrasive type cleaners must never be used. 16. Windows are never to be used as ladders, step stools, scaffolds or scaffold supports. 17. All work must start from, and be referenced to benchmarks, offset lines and/or column centerlines established by the architectural drawings and the general contractor. 18. All windows must be installed plumb, square, level and true, and in accordance with approved shop drawings and these installation instructions. 19. Glass and glazing building codes governing the design and use of products vary widely. YKK AP America Inc. does not control the selection of products, product configurations, operating hardware and function, or glazing materials, and YKK AP assumes no responsibility for these design considerations. It is the responsibility of the design professional, owner, architect, specifier, general contractor, and the installer to make these selections in strict accordance with all applicable codes. 20. Check our website, for the latest installation manual update prior to commencing work. Page-iii
6
7 STEP 1 DETERMINE WINDOW REFERENCE POINT INSTALLATION Establish the window reference lines or the exterior/interior plane of the windows to be installed using either bench marks, offset lines, or column centerlines provided by the general contractor and referenced on the shop drawings. Use the established reference points to determine the installation points for each window opening at the head, jambs, and sill. STEP 2 DETERMINE THE TYPE OF WINDOW ANCHORS TO BE USED The type of window anchoring used will depend upon the job conditions and the installer s preference. No. 10 fasteners are to be the minimum size used; consult the shop drawings and engineering calculations as the project conditions may require larger fasteners. See Details 1 & 2. Location of fasteners: -A maximum of 3 from the corner of all frames and receptors. -At 15 on center staggered from the front to the back. -A maximum of 3 on each side from the centerline of ventilator locking points. DETAIL 2 Window Receptor DETAIL 1 Steel strap anchors are available and when used, must be installed: -A minimum of 3 from the corner of all frames. -At 15 on center. -A maximum of 3 on each side from the centerline of ventilator locking points. -A maximum of 3 from the edge of framing joints, or mullions. See Detail 3. DETAIL 3 Steel Strap Anchor Page-1
8 INSTALLATION STEP 2 (Continued) DETERMINE THE TYPE OF WINDOW ANCHORS TO BE USED Refer to the specific fastener manufacturer s recommendations for proper edge distance and spacing for masonry applications. -Seal all screw heads that penetrate the framing water tight. See Detail 4. CAUTION: Do not fasten ceiling support angles, blind pockets, drapery tracks, convector covers or stools to the windows or the receptors. The window system is not designed to support the additional load and must be free to expand and contract under normal thermal cycling conditions. STEP 3 VENTILATOR INSTALLATION AND ADJUSTMENT All operating hardware and components must be checked for proper alignment, margins, and operation. -If necessary adjust the hinges, keepers, friction arms and pivots to ensure the proper operation of locking devices and the compression of the weather seal. -All hardware must be cleaned and lubricated as necessary to provide smooth operation. STEP 4 INSTALLATION OPTIONS AND PROCEDURES OPTION 1: Anchor with standard fasteners: 1. Install the frame plumb, square, level and true. -Refer to Step 2 or structural calculations for fastener size and location. -Shim as required along the frame and at all anchor points; 3/8 nominal joint width. -Seal the heads of all perimeter fasteners. 2. Install backer rod and seal with a quality perimeter sealant. See Detail 4. DETAIL 4 Page-2
9 INSTALLATION STEP 4 (Continued) INSTALLATION OPTIONS AND PROCEDURES OPTION 2: Anchor with optional steel strap anchors: 1. Refer to Step 2 or structural calculations for location of strap anchors. 2. Gently tap strap anchors into position making sure that the anchors are completely engaged. 3. Install the frame plumb, square, level and true. -Refer to Step 2 or structural calculations for fastener size and location. -Shim as required along the frame and on each side of strap anchors. 4. Install backer rod and apply a quality perimeter sealant. Tool the sealant to ensure a water tight joint. See Detail 5. OPTION 3: Install window receptor system at the head only or at the head and jambs: 1. Refer to Step 2 or structural calculations to determine the size and location of fasteners (minimum #10 fasteners). 2. Shim and secure the exterior leg of receptor(s) using the required fasteners; 3/8 nominal joint width. 3. When receptors are used at both the head and the jamb, the head receptor will run through. -Seal the intersection of receptors. 4. Install the window frame into the opening. 5. Shim the sill/jambs of the window to ensure that they are installed plumb, square, level and true. 6. Snap in interior receptor leg(s). 7. Install a #10 x 3/4 pan head fastener into the receptor at lock and hinge locations. 8. Anchor the window to the opening using Sealant the required fasteners. 9. Run a cap seal between the frame and receptor at the exterior. If the exterior of Cap Seal the window is inaccessible, run a bead of sealant along the backside of the receptor leg prior to installing the windows. 10. Install backer rod and apply a quality perimeter sealant. Tool the sealant to ensure a water tight joint. See Detail 6. 3/8 BE BE DETAIL 6 DETAIL 5 E #10 x 3/4 Screw At Lock & Hinge Locations Page-3
10 GLAZING STEP 5 PREP CASEMENT WINDOWS Casement windows require Corner Blocking for proper operation. 1. Verify that the frame and vent are properly aligned with a 1/8 margin around the entire perimeter of the vent. 2. Remove the glazing beads and clean the Vent exterior glazing leg with an approved cleaning agent using the two cloth cleaning method. 3. Install exterior glazing tape, E2-0670, on all four sides: -Leave a 1/8 gap between the edge of the tape and the edge of the ventilator. -Make certain that the corners of the tape do not overlap as this will prevent full contact around the perimeter of the glass. 4. Peel back the tape adhesive backing 3 to 4 at each corner and fold them towards the inside of the vent. See Detail 7. DETAIL 7 1/8 E Adhesive Backing 1/8 5. Install setting blocks at locations 1,2 and If bench glazing, make sure that the casement vent is fully supported from underneath before proceeding. 7. Unlock the ventilator lock and install a setting block at location Change setting blocks as required to square up the vent. 9. Raise up the vent s locking rail 1/16 and shim so that as the setting blocks compress the locks will align properly. See Detail 8. DETAIL 8 Finish glazing in accordance with standard glazing instructions in Steps 7 & 8 on Page 6. ** Glass weight is transferred to bottom corner and hinge. Page-4
11 GLAZING STEP 6 PREP FIXED AND PROJECTED WINDOWS 1/8 1. Verify that the frame and vent are properly aligned with a 1/8 margin around the entire perimeter of the vent. 2. Remove the glazing beads and clean the exterior glazing leg with an approved cleaning agent using the two cloth cleaning method. 3. Install exterior glazing tape, E2-0670, on all four sides: -Leave a 1/8 gap between the edge of the tape and the edge of the ventilator/frame. -Make certain that the corners of the tape do not overlap as this will prevent full contact around the perimeter of the glass. 4. Peel back the tape adhesive backing 3 to 4 at each corner and fold them towards the inside of the vent/window. See Detail 9. Vent DETAIL 9 E Adhesive Backing 1/8 1/4 Pts. 1/8 Pts. (6 Min.) FIXED 1/8 Pts. (6 Min.) 5. Install setting blocks at 1/8 points (at least 6 from jambs) for fixed frames, vents, and intermediate horizontal mullions. 6. Install (2) side blocks at 1/4 points for fixed frames and (1) side block at 1/3 points for projected vents as shown. See Detail 10. 1/3 Pts. PROJECTED VENT 1/8 Pts. (6 Min.) 1/8 Pts. (6 Min.) Finish glazing in accordance with standard glazing instructions in Steps 7 & 8 on Page 6. DETAIL 10 Page-5
12 GLAZING STEP 7 INSTALL GLASS 1. Center the glass and carefully set the unit down onto the setting blocks. 2. From the exterior of the window gently pull the folded adhesive backing ends to remove it and adhere the glass to glazing tape. See Detail Press the glass firmly against the exterior glazing tape. 4. Install the interior glass stops. 5. Cut interior wedge gasket to the day light opening dimension plus 1/8 per foot. 6. Install the wedge gasket by first installing each end and then the center of the gasket; push in the remainder of the gasket working from the center toward each end. See Detail 12. Adhesive Backing E Setting Block DETAIL 11 STEP 8 APPLY CAP BEAD 1. Apply Tremco Tremsil 600 sealant or equal to the joint between the glass and glazing leg. When applying sealant vertically, start at the bottom and work your way up. Make sure the sealant completely fills the joint. 2. Using a non-scratching implement, tool the sealant immediately after running the bead. Exert positive pressure to ensure that the sealant makes complete contact with all surfaces. Be careful not to remove too much sealant. Cap Bead Interior Wedge Gasket Glass Stop See Detail 12. DETAIL 12 Page-6
13 CALCULATING GLASS SIZES FW 3 3 /8 [85.7mm] FH 3 3 /8 [85.7mm] FW 3 3 /8 [85.7mm] h1,h /16 [74.6mm] w1,w /16 [74.6mm] FH 3 3 /8 [85.7mm] FW 5 7 /8 [149.2mm] FH 5 7 /8 [149.2mm] N/A N/A FW 5 7 /8 [149.2mm] h1 5 7 /16 [138.1mm] FW 3 3 /8 [85.7mm] h2 2 3 /8 [60.3mm] w1 5 7 /16 [138.1mm] FH 5 7 /8 [149.2mm] w2 2 3 /8 [60.3mm] FH 3 3 /8 [85.7mm] w1,w3 5 7 /16 [138.1mm] FH 5 7 /8 [149.2mm] w2 1 3 /8 [34.9mm] FH 3 3 /8 [85.7mm] NOTE: GLASS BITE = 1/2 (for 1/4 & 1 Glazing) w1,w2 5 3 /4 [146.1mm] FH 5 7 /8 [149.2mm] N/A N/A Page-7
14 CALCULATING GLASS SIZES FW 5 7 /8 [149.2mm] FH 5 7 /8 [149.2mm] N/A N/A FW 5 7 /8 [149.2mm] h1 5 7 /16 [138.1mm] FW 3 3 /8 [85.7mm] h2 2 3 /8 [60.3mm] w1,w2 5 7 /16 [138.1mm] h1 5 7 /16 [138.1mm] w1,w /16 [74.6mm] h2 2 3 /8 [60.3mm] FW 5 7 /8 [149.2mm] h1 5 7 /16 [138.1mm] h2 5 [127.0mm] FW 3 3 /8 [85.7mm] h3 2 3 /8 [60.3mm] NOTE: GLASS BITE = 1/2 (for 1/4 & 1 Glazing) Page-8
15 STEP 9 (Optional) INSTALL STACKING MULLION INSTALLATION OPTIONS E AS /4 [57.2mm] C L HM-2516 PC-1008 E Sealant #12-FC Exterior of Building E End Cap Sealant PC-1006 PC-1208 Cap Seal E E Anchor Clip DETAIL Install the first window assembly into the opening according to the instructions on Pages 1 thru Cut two pieces of gasket, E2-0051, to stacking mullion height and install into the reglets. 3. Install mullion end cap, E1-1536, to each end of the stacking mullion with a PC-1006 fastener. 4. Attach anchor clips to what will be the open side of the stacking mullion: -Attach anchor clip, E1-1537, to the top and bottom of one side of the stacking mullion such that each clip extends 1/4 past the end of the mullion. -Attach anchor clips with two PC-1208 fasteners at each end (do not completely tighten yet). 5. Install the stacking mullion into the opening according to Detail 13: -Slide each anchor clip tight against the masonry. -Attach each anchor clip to the masonry with two flat head fasteners. -Now completely tighten the PC-1208 fasteners used to attach the anchor clips to the mullion. 6. Carefully slide the second window assembly in and anchor it to the masonry. 7. To ensure a watertight seal run a bead of sealant up each interior frame jamb at the stacking mullion. Additionally, run a cap seal along the joint between the exterior frame jambs and the stacking mullion. If the exterior of the window is inaccessible, run a bead of sealant along the backside of each stacking mullion leg prior to installing the windows into the stacking mullion. 8. Attach the pressure plate, AS-4231, to the stacking mullion: -Install HM-2516 fasteners at 1-1/2 from each end maximum and then 9 on center. Pressure plates are pre-drilled; drill additional diameter (#9/32) holes if necessary. -Start installing fasteners at the center of the pressure plate and work towards each end. -Torque each fastener to 50 inch pounds. 9. Install PC-1008 fasteners, one on each side, through the pressure plate into the window frames: -(2) 6 below the top of the frame. -(2) 6 above the bottom of the frame. 10. Install snap cover, E9-5111, starting from the bottom and work up the mullion. Page-9
16 YKK AP America Inc The Bluffs Suite 100 Austell, Georgia
YOW 350 XT Thermally Broken Operable Window System
YOW 350 XT Thermally Broken Operable Window System MegaTherm Glass Fiber With 6/6 Nylon Thermal Break YOW 350 XT SYSTEM DESCRIPTION 3-1/2 Overall Frame Depth MegaTherm Thermal Break Construction: Frame
More informationYVS 400 TU Window System
YVS 400 TU SYSTEM DESCRIPTION YVS 400 TU PERFORMANCE FEATURES 4 Overall Depth ThermaBond Plus Poured & Debridged Thermal Break Variations: Single Hung, Double Hung & Fixed Windows 1 /8 & 1 1 /16 Glazing
More informationYSD 400 Sliding Door System Installation Manual
System Installation Manual 2006 YKK AP America Inc. is a subsidiary of YKK Corporation of America. TABLE OF CONTENTS Installation Notes........................................ Page ii PARTS DESCRIPTION
More informationINSTALLATION MANUAL STOREFRONT DOORS
INSTALLATION MANUAL STOREFRONT DOORS www.aluflam-usa.com SYSTEM DESCRIPTION - Extruded and filled aluminum framing, tested and approved by UL - 3-3/8 frame depth - Clear, fire-rated safety glazing - Door
More informationYES 45 TU Thermal Storefront System Installation Manual
Installation Manual 2004 YKK AP America Inc. is a subsidiary of YKK Corporation of America. TABLE OF CONTENTS Installation Notes........................................ Page ii PARTS DESCRIPTION Framing
More informationYES 40 FS/FI Storefront System Installation Manual
Installation Manual 2014 YKK AP America Inc. is a subsidiary of YKK Corporation of America. TABLE OF CONTENTS Installation Notes... Page ii PARTS DESCRIPTION YES 40 FS Framing Members... Page 1 YES 40
More informationYES 600 Thermal Clip Storefront System Installation Manual
Installation Manual 2004 YKK AP America Inc. is a subsidiary of YKK Corporation of America. TABLE OF CONTENTS Installation Notes........................................ Page ii Frame Types............................................
More informationYSG 40/50/50T Window Wall System Installation Manual
Installation Manual 2004 YKK AP America Inc. is a subsidiary of YKK Corporation of America. TABLE OF CONTENTS Installation Notes........................................ Page ii PARTS DESCRIPTION YSG 40
More informationYWE 40 T Window Wall System Installation Manual
Installation Manual 2005 YKK AP America Inc. is a subsidiary of YKK Corporation of America. TABLE OF CONTENTS Installation Notes........................................ Page ii Frame Types............................................
More informationYES 45 XT High Performance Thermal Storefront System
Dual Thermal Barrier ThermaBond Plus Pour & Debridge Technology Installation Manual 2015 YKK AP America Inc. is a subsidiary of YKK Corporation of America. TABLE OF CONTENTS Installation Notes... Page
More informationYCW 752 Outside Glazed Curtain Wall System Installation Manual
YCW 752 Outside Glazed Curtain Wall System Installation Manual 2007 YKK AP America Inc. is a subsidiary of YKK Corporation of America. TABLE OF CONTENTS Installation Notes........................................
More informationYSD 600 T/TH Sliding Door System Installation Manual
System Installation Manual 2006 YKK AP America Inc. is a subsidiary of YKK Corporation of America. TABLE OF CONTENTS Installation Notes........................................ Page ii & iii PARTS DESCRIPTION
More informationSwing Door Installation Manual
Manual 20D/35D/50D 20DH/35DH 40M/50M 25FD 35XT 50XT 01-4000-03 2010 YKK AP America Inc. is a subsidiary of YKK Corporation of America. TABLE OF CONTENTS Installation Notes.......................................
More informationInstallation Manual. YSD 600 T/TH Sliding Door. YSD 600 T/TH Sliding Door System
YSD 600 T/TH Sliding Door System Installation Manual 2014 YKK AP America Inc. is a subsidiary of YKK Corporation of America. TABLE OF CONTENTS Installation Notes... Page ii & iii PARTS DESCRIPTION Framing
More informationYCW 750 OG Outside Glazed Curtain Wall System Installation Manual
YCW 750 OG Outside Glazed Curtain Wall System Installation Manual 2004 YKK AP America Inc. is a subsidiary of YKK Corporation of America. TABLE OF CONTENTS Installation Notes........................................
More informationYCW 750 IG Inside Glazed Curtain Wall System Installation Manual
Installation Manual 2014 YKK AP America Inc. is a subsidiary of YKK Corporation of America. TABLE OF CONTENTS Installation Notes... Page ii PARTS DESCRIPTION YCW 750 IG Framing Members... Page 1 to 3
More informationDHS-500 IMPACT SYSTEM INSTALLATION MANUAL
DHS-500 IMPACT SYSTEM INSTALLATION MANUAL TABLE OF CONTENTS SECTION PAGE GENERAL NOTES 3 EXTRUSION & PARTS IDENTIFICATION 4-5 DETERMINE FRAME SIZE 6 FABRICATE VERTICAL MULLIONS & FILLERS 7-8 FABRICATE
More informationYHC 300 SSG Structural Silicone Glazed Curtain Wall System Installation Manual
YHC 300 SSG Structural Silicone Glazed Curtain Wall System Installation Manual 2007 YKK AP America Inc. is a subsidiary of YKK Corporation of America. TABLE OF CONTENTS Installation Notes........................................
More informationYES 45 FS/FI Storefront System Installation Manual
Installation Manual 2014 YKK AP America Inc. is a subsidiary of YKK Corporation of America. TABLE OF CONTENTS Installation Notes... Page ii PARTS DESCRIPTION YES 45 FS Framing Members... Page 1 YES 45
More informationGENERAL INSTALLATION GUIDELINES
1551 MT. ROSE AVENUE YORK PA 17403-2909 (717) 849-8100 GENERAL INSTALLATION GUIDELINES For Receptor Systems Approved 9/29/2017 Installation Guideline Disclaimer This document contains general installation
More informationGENERAL INSTALLATION GUIDELINES
1551 MT. ROSE AVENUE YORK PA 17403-2909 (717) 849-8100 GENERAL INSTALLATION GUIDELINES For Receptor Systems Approved 08/31/2018 Installation Guideline Disclaimer This document contains general installation
More informationThermally Broken Framing and Door Installation
INSTALLATION INSTRUCTIONS Thermally Broken Framing and Door Installation IMPORTANT: Read all instructions before beginning installation. These instructions are provided to help prevent installation problems
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Thermally Broken Framing and Door Installation SL-450TB (2" x 4-1/2" with 1" Glazing) & SL-600TB (2" x 6" with 1" Glazing) IMPORTANT: Read all instructions before beginning installation.
More informationYHC 300 IG Inside Glazed Curtain Wall System Installation Manual
YHC 300 IG Inside Glazed Curtain Wall System Installation Manual 2007 YKK AP America Inc. is a subsidiary of YKK Corporation of America. TABLE OF CONTENTS Installation Notes........................................
More informationSeries Sloped glazed Curtain wall. Installation Instructions
Series 5600 Sloped glazed Curtain wall Installation Instructions Part NO. Y308 February 2013 SECTION TABLE OF CONTENTS PAGE I. General Notes & Guidelines. 3-4 II. Gutter and Mullion Assembly.. 5 III. End
More information14000 I/O Series Flush Glaze. Fabrication and Installation Instructions
14000 I/O Series Flush Glaze Fabrication and Installation Instructions Last saved on 12/18/2009 Table of Contents GENERAL CONSTRUCTION NOTES...3 EXTRUDED ALUMINUM PARTS...4 ACCESSORIES...5 OVERVIEW...6
More informationINSTALLATION INSTRUCTIONS FOR REPLACEMENT FORGENT WOOD GLASTRA WINDOWS RECOMMENDATIONS FOR COMMON INSTALLATION OF ALL REPLACEMENT WINDOWS.
INSTALLATION INSTRUCTIONS FOR REPLACEMENT FORGENT WOOD GLASTRA WINDOWS RECOMMENDATIONS FOR COMMON INSTALLATION OF ALL REPLACEMENT WINDOWS. Installer: DO NOT DISCARD Please leave the Installation Guide
More informationYCW 750 OG Outside Glazed Curtain Wall System Installation Manual
YCW 750 OG Outside Glazed Curtain Wall System Installation Manual 2012 YKK AP America Inc. is a subsidiary of YKK Corporation of America. TABLE OF CONTENTS Installation Notes... Page ii PARTS DESCRIPTION
More informationNARROW, MEDIUM AND WIDE STILE, THERMASTILE AND DURASTILE. Installation Instructions
NARROW, MEDIUM AND WIDE STILE, THERMASTILE AND DURASTILE Installation Instructions PART Y015 JUNE 2016 Table of Contents Section 1. GENERAL NOTES AND GUIDELINES... 2. DOOR HARDWARE A. Locks B. Push/Pulls
More informationInstallation Instructions
Installation Instructions 1293 N. Harvey Mitchell Pkwy. Bryan, Texas 77803 800.444.1444 ph 979.823.1005 fax www.aswcommercial.com Simplifying Windows Complete Architectural CD Binder Inside B l as t I
More informationYHS 50 TU Storefront System & Model 35H Door Installation Manual
Installation Manual 2012 YKK AP America Inc. is a subsidiary of YKK Corporation of America. TABLE OF CONTENTS Installation Notes... Page ii PARTS DESCRIPTION YHS 50 TU Framing Members... Page 1 YHS 50
More informationINSTALLATION INSTRUCTIONS SIDELITE ASSEMBLY SERIES 900 TERRACE DOOR AND SERIES 925 PATIO DOOR
INSTALLATION INSTRUCTIONS SIDELITE ASSEMBLY SERIES 900 TERRACE DOOR AND SERIES 925 PATIO DOOR Phone: (800) 262-5151 Fax: (866) 262-3299 crlaurence.com usalum.com crl-arch.com 11M0292 HANDLING, STORAGE,
More informationSERIES 300 SINGLE HUNG WINDOW INSTALLATION
IMPORTANT INFORMATION: WHETHER IT BE LOCATION OR INSTALLATION TYPE, NOT ALL WINDOW TYPES CAN BE INSTALLED IN ALL AREAS OR WALL CONDITIONS. CONSULT YOUR LOCAL BUILDING CODE DEPARTMENT FOR ANY REGULATIONS
More informationSeries Advanced and alternate. Installation Instructions
Series 5500 Advanced and alternate Installation Instructions Part NO. Y557 February 2013 TABLE OF CONTENTS SECTION S-5500 ADVANCED INSTALLATION INSTUCTIONS PAGE I. General Notes and Guidelines...... 3-4
More informationINSTALLATION INSTRUCTIONS. Thermal Entrances AA 250/AA 425 THERMAL DOOR WITH TRIFAB 601/601T FRAMING
JANUARY, 2014 1 INSTALLATION Thermal Entrances AA 250/AA 425 THERMAL DOOR WITH TRIFAB 601/601T FRAMING INSTRUCTIONS 2 FRAME ASSEMBLY JANUARY, 2014 601442 SHEAR BLOCK BALL BEARING NRP BUTT (FACTORY APPLIED
More informationHeavy Wall Applied Stop Tube Frame and Door Installation
INSTALLATION INSTRUCTIONS Heavy Wall Applied Stop Tube Frame and Door Installation Read all instructions before beginning installation. These instructions are provided to help prevent installation problems
More informationSun Control-Solar Eclipse-Solar Shelf
Sun Control-Solar Eclipse-Solar Shelf Note: Installation and Glazing Manuals are product specific. FOR REVIEW ONLY! TABLE OF CONTENTS GENERAL INFORMATION Product Use...Page 3 Protection and Storage...Page
More informationYHS 50 FS Storefront System & Model 35H/50H Door Installation Manual
Installation Manual 2014 YKK AP America Inc. is a subsidiary of YKK Corporation of America. TABLE OF CONTENTS Installation Notes... Page ii PARTS DESCRIPTION YHS 50 Framing Members... Page 1 YHS 50 Accessories...
More information4500 Series. Fabrication and Installation Instructions
4500 Series Fabrication and Installation Instructions E4500 Series July, 2017 Table of Contents GENERAL CONSTRUCTION NOTES... 3 EXTRUDED ALUMINUM PARTS... 5 ACCESSORIES... 7 OVERVIEW... 8 FRAME FABRICATION...
More informationStorefront Installation Guide
Storefront General Notes: 1. Check Contract Documents and Shop Drawings. Understand and clarify any Field Verify Notes and approvals of drawings and products to be familiar with the project. Installation
More informationINSTALLATION INSTRUCTIONS SERIES 487 CENTER GLAZED WITH 1-1/2" TRIM OFFICE PARTITIONS
INSTALLATION INSTRUCTIONS SERIES 87 CENTER GLAZED WITH -/" TRIM OFFICE PARTITIONS Phone: (800) -6 Fax: (800) 58-7 crlaurence.com usalum.com crl-arch.com M056_Rev_D SERIES 87 OFFICE PARTITIONS CENTER GLAZED
More informationSERIES 300 SINGLE HUNG WITH FIN WINDOW INSTALLATION
IMPORTANT INFORMATION: WHETHER IT BE LOCATION OR INSTALLATION TYPE, NOT ALL WINDOW TYPES CAN BE INSTALLED IN ALL AREAS OR WALL CONDITIONS. CONSULT YOUR LOCAL BUILDING CODE DEPARTMENT FOR ANY REGULATIONS
More informationFG-5100T STORMMAX INSTALLATION AND GLAZING MANUAL NOTE:
BuildingEnvelope R FG-5100T STORMMAX INSTALLATION AND GLAZING MANUAL NOTE: THE INSTALLATION DETAILS FOUND IN THIS PACKAGE ARE GENERIC AND ARE FOR REPRESENTATION ONLY WITH THE INTENT OF GIVING THE INSTALLATION
More information14000 Series. Fabrication and Installation Instructions
14000 Series Fabrication and Installation Instructions 14000 Series Revision December 01, 2009 Table of Contents GENERAL CONSTRUCTION NOTES... 3 EXTRUDED ALUMINUM PARTS... 4 ACCESSORIES... 7 OVERVIEW...
More information14000 Series. Fabrication and Installation Instructions
14000 Series Fabrication and Installation Instructions Revision May 2013 Table of Contents GENERAL CONSTRUCTION NOTES...3 EXTRUDED ALUMINUM PARTS...5 ACCESSORIES...8 OVERVIEW...10 FRAME FABRICATION...15
More informationINSTALLATION INSTRUCTIONS IMPERVIA SLIDING PATIO DOOR WITH FINS
2008 Pella Corporation Part Number: 803V0101 INSTALLATION INSTRUCTIONS IMPERVIA SLIDING PATIO DOOR WITH FINS Installation Instructions for Typical Wood Frame Construction. These instructions were developed
More informationStorefront Installation Guide INSTALLATION INSTRUCTIONS
STOREFRONT General Notes 1. Check contract documents and shop drawings, and understand and clarify any Field Verify Notes, approvals of drawings, and products required to be familiar with the project.
More informationNote: Installation and Glazing Manuals are product specific. FOR REVIEW ONLY! May 2015
Note: Installation and Glazing Manuals are product specific. FOR REVIEW ONLY! May 2015 Phone: 1-866-OLDCASTLE (653-2278) Web Address: www.oldcastlebe.com S E R I E S 6 0 0 0 X T - S T O R E F R O N T I
More informationSTACKING MULTI-SLIDE DOOR SYSTEM INSTALLATION INSTRUCTIONS
STACKING MULTI-SLIDE DOOR SYSTEM INSTALLATION INSTRUCTIONS 1290363 Revision 1 12/16 Page 1 Weather Shield Mfg., Inc. NOTICE CAUTION! Failure to install and maintain our product according to these instructions
More informationFlashing Materials. Rough Opening Preparation
Installation Instructions for CertainTeed New Construction Windows Handling vinyl windows CAUTION: Always store vinyl windows and doors in an upright position on a slight angle. Never lay them flat or
More informationSERIES 5001 SLIDING GLASS DOOR PATIO DOORS INSTALLATION GUIDE
PATIO DOORS INSTALLATION GUIDE These instructions cover general installation conditions. Improper installation could affect your doors operation and warranty. Deviations from these instructions should
More informationCurtain Wall Installation Guide
Curtain Wall Installation Guide Curtain Wall Installation Guide 1 IMPORTANT NOTICES! Important Notices & Information Manufacturer s Notes: The building envelope must be correctly prepared with weather
More informationPhone # La Jolla Doors. Block Frame Installation Manual Aluminum Frame with either Vinyl or Aluminum Panels
Phone # 800-440-8785 www.lajolladoors.com La Jolla Doors Block Frame Installation Manual Aluminum Frame with either Vinyl or Aluminum Panels Thank you for choosing La Jolla Doors In this manual you will
More informationSeries Exterior glazed curtain wall. Installation Instructions
Series 5500 Exterior glazed curtain wall Installation Instructions Part NO. Y550 November 2016 TABLE OF CONTENTS SECTION S-5500 SCREW SPLINE CURTAIN WALL PAGE I. General Notes and Guidelines.. 3-4 II.
More informationInstallation Recommendations for Finless Frame Doors
Installation Recommendations for Finless Frame Doors These installation recommendations are made available by MI Windows and Doors, LLC (MI) to assist with the integration of finless or flange sliding
More informationInstallation Instructions Double-Hung, Single-Hung, Casement, Awning, Sliding, Picture & Shapes Non-Impact & Impact Resistant Nailing Fin Windows
Installation Instructions Double-Hung, Single-Hung, Casement, Awning, Sliding, Picture & Shapes Non-Impact & Impact Resistant Nailing Fin Windows americancraftsmanwindows.com Project Requirements: Read
More informationRead guide from beginning to end before starting installation. Read all warnings and cautions during unit installation.
Installation Guide for E-Series/Eagle High-Performance Mullion Windows with LVL Reinforcement and Installed Using Type B Clips Thank you for choosing Andersen. Instructions are for typical, new wood-framed
More informationInstallation Guidelines For Quaker Window Products Aluminum flange fin sub sill & receptor system using a T mulled twin window unit.
Installation Guidelines For Quaker Window Products Aluminum flange fin sub sill & receptor system using a T mulled twin window unit. Installer: Read these instructions completely before starting any installation.
More informationInstallation Instructions
Installation Instructions 200 Series Curtainwall 3056 WALKER RIDGE DR. NW, SUITE G WALKER, MI 49544 800-866-2227 dependable@tubeliteinc.com Revised April 2014 dependable@tubeliteinc.com Page 1 TABLE OF
More informationVinyl Windows and Doors Manufactured by Pella Corporation
Vinyl Windows and Doors Manufactured by Pella Corporation Part Number: V981255 2009 Pella Corporation INSTALLATION INSTRUCTION - INSTRUCCIONES DE INSTALACIÓN FOR BOW WINDOWS WITHOUT HEAD AND SEAT BOARD
More informationELEPHANT DOOR SYSTEMS SERIES E1200
INSTALLATION INSTRUCTIONS ELEPHANT DOOR SYSTEMS SERIES E1200 Phone: (800) 262-5151 Fax: (866) 262-3299 crlaurence.com usalum.com crl-arch.com AVDB3096 03.13 TABLE OF CONTENTS SUBJECT PAGE GENERAL INSTALLATION
More informationSliding Glass Door Assembly and Installation Guide
Sliding Glass Door Assembly and Installation Guide Index Door System Components and Hardware The following components are needed to complete the installation of your Sliding Patio Door unit. Check all
More informationInstallation Guide for Architectural Wood Hinged Windows
Guide for Architectural Wood Hinged Windows Congratulations! You have just purchased one of the many fine Andersen products. Proper assembly, installation and maintenance are essential if the benefits
More informationWindow Frame Installation Instructions For Nail-on and Block Frames
General The key to any window or door installation is preparation. This extends from storage of the product to the final installation and to all points in between. Careful planning and attention to detail
More informationFold-A-Way Patio Door ASSEMBLY & INSTALLATION GUIDE
Fold-A-Way Patio Door ASSEMBLY & INSTALLATION GUIDE This instruction guide provides the minimum recommended procedures to correctly prepare the rough opening, install a fold-a-way patio door unit and apply
More informationAssembled Patio Door Installation Guide 2-Panel Patio Door with Non-Welded Frame
Assembled Patio Door Installation Guide 2-Panel Patio Door with Non-Welded Frame americancraftsmanwindows.com American Craftsman and all other marks where denoted are trademarks of Andersen Corporation
More informatione-lite fabrication/assembly and Installation instructions
e-lite fabrication/assembly and Installation instructions Part NO. YWLS February 2013 TABLE OF CONTENTS SECTION PAGE I. General Notes and Guidelines.. 3-4 II. E-Lite Stick Built Channel Base Assembly...
More informationSun Windows General Information New Construction Hinged Door Installation Instructions
A G H F H H A. Apply Weather Resistive Barrier B. Apply Bottom Flashing Tape C. Install Sill Pan End Caps & Pan D. Caulk Sides & Top Nailing Surface, Set Door, Fasten E. Apply Side Flashing Tape F. Apply
More informationFlushglaze For Framed Openings and Horizontal Panels. Window System Installation Guide
Flushglaze 4500 For Framed Openings and Horizontal Panels Window System Installation Guide January 2017 BENCHMRK Welcome to Kingspan, global leaders in the design and manufacture of insulated metal panels
More informationVinyl Windows and Doors Manufactured by VPI Quality Windows
Vinyl Windows and Doors Manufactured by VPI Quality Windows Part Number: 511_Installation ENDURANCE CASEMENT\AWNING\PW INSTALLATION INSTRUCTIONS Installation Instructions for Typical Construction These
More informationSeries 7600 Installation Instructions Aluminum Multi-Slide Door (Pocketing)
Series 7600 Installation Instructions Aluminum Multi-Slide Door (Pocketing) Things to Know Before You Start Things to Know Before You Start Removal of Old Fenestration Products Ensure any old fenestration
More information4. Partially open the operating panel and tilt the top toward the interior of the door (Figure 4). Lift the panel off the sill and set it aside.
Effective Date: 10/1/2017 Tools Needed Kit Contents Hardware Kit Safety Glasses Cordless drill Phillips screw bit Two-step drill bit (3/8-1/8 ) utility knife Interior Mullion Exterior Mullion Cover clamps
More informationINSTALLATION INSTRUCTIONS 2 x 4 1/2 for 1 Glass
INSTALLATION INSTRUCTIONS 2 x 4 1/2 for 1 Glass Deep pocket allows for direct anchor attachment to substrate without flat filler plate. 1/4 Ø perimeter anchor holes allows for direct anchor attachment
More informationINSTALLATION INSTRUCTIONS FRAMELESS CONTINUOUS HINGE SHOWER ENCLOSURE QCI5233
INSTALLATION INSTRUCTIONS FRAMELESS CONTINUOUS HINGE SHOWER ENCLOSURE QCI5233 QCI5233 Rev 0 Page 1 Certified 06/20/2016 INSTALLATION NOTES: Unpack your unit carefully and inspect for freight damage. Lay
More informationINSTALLATION INSTRUCTIONS for Wood/Clad Wood Windows without Exterior Trim or Nailing Fin (JII025) ImpOrTaNT INFOrmaTION & GlOssary.
for Wood/Clad Wood Windows without Exterior Trim or Nailing Fin (JII025) Thank you for selecting JELD -WEN products. Attached are JELD-WEN s recommended installation instructions for metal clad wood windows
More informationInstallation Instructions for Vista Air Vertically Folding Walls
Installation Instructions for Vista Air Vertically Folding Walls Use these instructions in conjunction with your shop drawings to see the specifics that are particular to the model you are installing.
More informationSERIES BW3250 BLAST WALL TABLE OF CONTENTS INSTALLATION INSTRUCTIONS GENERAL NOTES
I N S TA L L AT I O N I N S T R U C T I O N S BW3250 BLAST RESISTANT CURTAIN WALL Page 2 SERIES BW3250 BLAST WALL TABLE OF CONTENTS United States Aluminum PAGE GENERAL NOTES...2 and 3 FABRICATION...4 through
More informationInstallation Guidelines For ALUMINUM M-SERIES 3 PANEL SLIDING DOOR
www.quakerwindows.comv www.quakercommercialwindows.com PO Box 128 504 Highway 63 South Freeburg, MO 65035 800-347-0438 573-469-4151 (fax) Installation Guidelines For ALUMINUM M-SERIES 3 PANEL SLIDING DOOR
More informationVYTEX PREMIUM SLIDING GLASS DOOR. Table of Contents. Precautions and Safety 2. Tools Required...3. Inspect and Prepare Door...4
VYTEX PREMIUM SLIDING GLASS DOOR Table of Contents Precautions and Safety 2 Tools Required...3 Inspect and Prepare Door...4 Hardware and Parts Check List....4 Master Frame Assembly 5 Master Frame Installation..7
More informationInstallation Guide. for E-Series/Eagle Clad Hinged Inswing French Door
Installation Guide for E-Series/Eagle Clad Hinged Inswing French Door Thank you for choosing Andersen. Instructions are for typical, new wood-framed wall construction with weather protection in place.
More informationSeries 7650 Installation Instructions Sliding Glass Door
Series 7650 Installation Instructions Sliding Glass Door Things to Know Before You Start Things to Know Before You Start Removal of Old Fenestration Products Ensure any old fenestration products are removed
More informationINSTALLATION GUIDE WOOD PIVOTING CIRCLE/ OVAL
WOOD PIVOTING CIRCLE/ OVAL READ SPECIFIC INSTALLATION INSTRUCTIONS COMPLETELY BEFORE STARTING ANY INSTALLATION Failure to install and maintain our product according to these instructions will VOID any
More informationBlock Frame Inovo Patio Door/Transom/Sidelite Field Mulling Instructions. simonton.com/installation. If mulling sidelites, skip to Step 5.
Effective Date: 10/1/17 Tools Needed Kit Contents Safety Glasses Cordless Drill Phillips Screw Bit Two-step Drill Bit (3/8-1/8 ) Utility Knife Interior Mullion Exterior Mullion Cover Hardware Kit Clamps
More informationVinyl Windows Manufactured by VPI Quality Windows
Vinyl Windows Manufactured by VPI Quality Windows Part Number: 531&591 Installation 531 & 591 SERIES SLIDING AND HUNG WINDOW INSTALLATION INSTRUCTIONS Installation Instructions for Typical Construction.
More informationINSTALLATION INSTRUCTIONS TRIFAB 451UT SCREW SPLINE ASSEMBLY TRIFAB 451UT. AUGUST, 2010 (Part No. 452T-CG-970) EC
AUGUST, 2010 (Part No. 452T-CG-970) EC 97904-31 1 INSTALLATION SCREW SPLINE ASSEMBLY Kawneer Company, Inc., 2010 INSTRUCTIONS 2 TABLE OF CONTENTS (452T-CG-970) AUGUST, 2010 These instructions show the
More informationINOVO 4-LITE SLIDING PATIO DOOR ASSEMBLY AND INSTALLATION INSTRUCTIONS
INOVO 4-LITE SLIDING PATIO DOOR ASSEMBLY AND INSTALLATION INSTRUCTIONS IMPORTANT: READ THE INSTRUCTIONS AND FAMILIARIZE YOURSELF WITH THE DOOR PARTS AND PIECES BEFORE BEGINNING ASSEMBLY AND INSTALLATION.
More informationInstallation Guide for Andersen Architectural Clad Inswing Entry and Patio Doors
Installation Guide for Andersen Architectural Clad Inswing Entry and Patio Doors Congratulations! You have just purchased one of the many fine Andersen products. Proper assembly, installation and maintenance
More informationINSTALLATION INSTRUCTIONS TRIFAB VG SCREW SPLINE ASSEMBLY TRIFAB VG 450 TRIFAB VG 451 TRIFAB VG 451T
INSTALLATION TRIFAB VG SCREW SPLINE ASSEMBLY TRIFAB VG 450 TRIFAB VG 451 TRIFAB VG 451T INSTRUCTIONS LITHO IN U.S.A. JANUARY KAWNEER COMPANY, INC., 2004 451-VG-970.01.04a PART NO. 451-VG-970 1 INSTALLATION
More informationINSTALLATION INSTRUCTIONS FOR FORGENT SLIDING PATIO DOORS RECOMMENDATIONS FOR COMMON INSTALLATION OF SLIDING PATIO DOORS.
INSTALLATION INSTRUCTIONS FOR FORGENT SLIDING PATIO DOORS RECOMMENDATIONS FOR COMMON INSTALLATION OF SLIDING PATIO DOORS. Installer: DO NOT DISCARD Please leave the Installation Guide with the home owner
More informationPIVOT DOOR 3400P INSTALLATION INSTRUCTIONS
Table of Contents I. Tools, Sealant Requirements, Anchor Recommended Table...1 II. Opening, Frame & Panel Verification...2-3 III. Frame Assembly...4 IV. Frame Installation...5-7 V. Glazing Instructions...8
More informationASSEMBLY AND INSTALLATION INSTRUCTIONS for Premium Aluminum and Premium Atlantic Aluminum Sliding Patio Doors (JII020)
for Premium Aluminum and Premium Atlantic Aluminum Sliding Patio Doors (JII020) Thank you for selecting jeld-wen products. Attached are jeld-wen s recommended installation instructions for Premium Aluminum
More information1200 SERIES 2 PANEL DOOR rev.1 DETAILED INSTALLATION INTRUCTIONS
1200 SERIES 2 PANEL DOOR 10.2013 rev.1 DETAILED INSTALLATION INTRUCTIONS GENERAL: Door elevations shown in these instructions are as viewed from the outside. X denotes the active or moving panel(s). O
More informationInstallation Guide for Andersen Architectural Clad Hinged Windows
Guide for Andersen Architectural Clad Hinged Windows Congratulations! You have just purchased one of the many fine Andersen products. Proper assembly, installation and maintenance are essential if the
More informationWOOD OUT SWING AWNING, CASEMENT, & HOPPER WINDOW
WOOD OUT SWING AWNING, CASEMENT, & HOPPER WINDOW INSTALLATION GUIDE READ SPECIFIC INSTALLATION INSTRUCTIONS COMPLETELY BEFORE STARTING ANY INSTALLATION Failure to install and maintain our product according
More informationINSTALLATION INSTRUCTIONS
900 SERIES RIBBON WINDOW INSTALLATION INSTRUCTIONS 3056 Walker Ridge Dr. NW, Suite G Walker, MI 49544 800-866-2227 November 2016 www.tubeliteinc.com Page 1 TABLE OF CONTENTS GENERAL CONSTRUCTION NOTES...3-4
More informationVinyl Sliding Glass Door Assembly Instructions
Vinyl Sliding Glass Door Assembly Instructions SERIES SGD 5470/5570 Para instrucciones en español, visite: http://bit.ly/pgtassemblyinstructions Parts List ITEM 4 5 6 7 8 9 0 4 5 6 7 8 SGD 5470/5570 PARTS
More informationINSTALLATION INSTRUCTIONS FOR TEUTONIC ENTRANCE DOOR RECOMMENDATIONS FOR COMMON INSTALLATION OF ENTRANCE DOORS.
INSTALLATION INSTRUCTIONS FOR TEUTONIC ENTRANCE DOOR RECOMMENDATIONS FOR COMMON INSTALLATION OF ENTRANCE DOORS. Installer: DO NOT DISCARD Please leave the Installation Guide with the owner. Please read
More informationINSTALLATION INSTRUCTION - INSTRUCCIONES DE INSTALACIÓN FOR CLAD CASEMENT & AWNING WINDOW VENTANA DE DOS HOJAS CON REVESTIMIENTO
2008 Pella Corporation Part Number: 801P0101 INSTALLATION INSTRUCTION - INSTRUCCIONES DE INSTALACIÓN FOR CLAD CASEMENT & AWNING WINDOW VENTANA DE DOS HOJAS CON REVESTIMIENTO Corner Corner Top Fin Corner
More informationNote: Installation and Glazing Manuals are product specific. FOR REVIEW ONLY! FEBRUARY 2012
Note: Installation and Glazing Manuals are product specific. FOR REVIEW ONLY! Phone: 1-866-OLDCASTLE (653-2278) Web Address: www.oldcastlebe.com FG-1000 & FG-2000 INSTALLATION & GLAZING INSTRUCTIONS These
More informationSun Windows General Information New Construction Sliding Door Installation Instructions H F
A G B D C H F H E H A. Apply Weather Resistive Barrier B. Apply Bottom Flashing Tape C. Install Sill Pan End Caps & Pan D. Caulk Sides & Top Nailing Surface, Set Door, Fasten E. Apply Side Flashing Tape
More information