Jass.Performance Low Profiles Installation Manual

Size: px

Start display at page:

Download "Jass.Performance Low Profiles Installation Manual"

Mitchell Lane
5 years ago
Views:

Jass.Performance Low Profiles Installation Manual What is in the box: 2x Adapter Frame 2x Outer Panels 2x Inner Panels Pushrod, Ball Joints & Brackets 2x Hella Headlights 6x Springs 4x M6x25 Cross

1 Jass.Performance Low Profiles Installation Manual What is in the box: 2x Adapter Frame 2x Outer Panels 2x Inner Panels Pushrod, Ball Joints & Brackets 2x Hella Headlights 6x Springs 4x M6x25 Cross Head Bolts For The Adapter Frame 4x M6x12 Hex Bolts For The Brackets To Headlight Body 4x M6 Locknuts For The Adapter Frame 4x M6 Nuts The Jass.Performance Low Profiles are featuring: Fully reversible upgrade of the stock headlight bodies. Premium branded E-signed, TÜV approved Hella headlights with integrated low/high beam. Significantly improved light output to the US headlights. Extremely low profile design of only 9cm maximum lift. Optimized aerodynamics with headlights up, improved top speed. Significantly enhanced sportier appearance. Full manual adjustability top, bottom, left right. Preserving the MOT/TÜV relevant el. height adjustability. 6x Black Screws For The Panels 2x Black Screws For The Panel 2x M6x60 Hex Bend Bolts 2x Plastic Spacers 6x 6mm Washers Tools needed You will need the following tools for the conversion: - Philips screwdriver - 10mm socket wrench - 13mm socket wrench - 14mm socket wrench - 6mm drill bit - Drilling machine

2 Preparation 5. Lift the bodies carefully. Both headlight bodies have to be removed in order to prepare them for Low Pro adapters. Removing the el. motors for the headlights and the adjustability is not necessary. 6. Remove the 3 plastic screws from the black rubbers in front of the headlight bodies and remove them. Electronics 1. The headlight motors are programmed for self-adjustment. To prevent self-rotation during the installation process we will remove their fuse in the left fuse box in the engine bay. Look for 30 ampere RETRACTOR fuse in the box and pull it out for the moment. 2. Remove the connector from both headlights. 3. Remove the connectors from the height adjustment motors on the headlight bodies. They are to be found on the outer side of each, in case available. Hardware 1. Unscrew the 4 cross head screws on the plastic covers of each headlight and remove it. Now you need to remove the round headlights. 7. Fully remove the 3 screws, including the springs and washers (the locations may vary depending on the country). 2. Unscrew the 4 screws of each lid and remove them both. 3. Unscrew the 14mm screw of the el.motor. Remove it carefully with the washer. 8. Take the headlights off. Now is the moment to swap the H4 bulbs to the new Hella headlights. In case the OEM headlights are the sealed units (USA and some other countries) you need to source a pair of H4 automotive bulbs. 9. Remove the pushrod from the headlights bodies, by evenly pulling it out of the pivoting ball. 4. Unscrew the two screws pivoting the headlight body. Collect the screws and nuts. 10. Remove the bracket on the inner top side for the OEM headlight fixing, held by 3 cross head screws (triangle shaped).

3 Installation Pushrod & brackets To have the Low Profiles installation fully reversible, we will preserve the original pivoting point and install new pushrods on a new bracket (picture below). 118mm Mark the centers of the fixing points to the headlight body and carefully drill two 6mm holes. The bracket is secured with the provided 2x M6x12mm screws (10mm head). Repeat on the other headlight. It is essential to position the bracket correctly on the headlight body frame. The brackets for the new pivoting point needs to be positioned as shown on the picture with the rivet centered in the middle of the bracket hole. The rivet is the rear part of the original ball joint head. Please note the pushrod for the left and right side are different the brackets differ accordingly. The bottom picture shows the installed position of the nuts, drilled, installed from the other side. Also visible is the bended stopper bolt, that replaces the short OEM one (the longer bended one compensates for the considerably less travel of the headlight as low pro version). Having the brackets installed, you need to screw the pushrod with the two ball joints with the provided M8 securing screw to the bracket. The front of the bracket aligns with the metal edge as shown on the next picture: 40mm The other side of the pushrod with the lever will be later adjusted and screwed to the headlight retracting motor shaft. The outer length of the pushrod assembled has to be 118mm, the distance between the inner of the ball joints 40mm. This is sold preset and you will not need to adjust, the above information is just in case you have sourced used/changed set.

Installing the adapter frame The adapter frame uses 3 points for the installation at the bottom the el. motor or original mounting point. At the top the leftmost and right most holes.

Secure the both top screws with the provided locknuts with plastic inserts.

4 Installing the adapter frame The adapter frame uses 3 points for the installation at the bottom the el. motor or original mounting point. At the top the leftmost and right most holes. The installation sequence is as shown on the picture with the headlight body between the adapter and washer: Other than the stock, the springs need to be fitted behind the headlight body. Secure the both top screws with the provided locknuts with plastic inserts. Do not fully tighten the springs, as they are allowing the pivoting of the headlight frame and the automatic height adjustment. 3-5mm thread left behind the nut (as shown) should be fine. Installing the headlights Having the adapter in place, the headlights can be installed. They are screwed on both sides with the provided selftaping screws. At the bottom the original screw should be re-used to fix the adapter frame to the headlight body. In case of manual headlight beam adjustment it screws to the plastic insert as used to. In case of el. headlights adjustment it screws to the el.motor hole as the stock does. Either way the provided spring or the original spring can be used on this place, but you need to use the original bolt. The adapter frame shown mounted below. Fully tighten them. In case the headlight doesn t lie perfectly on the frame, refer to the next topic. Stopper screws There are two stopper screws for the upper and bottom position of the headlight. Their proper adjustment ensures the stability of the headlight during drive. With the old adjustment screw removed, you have to provisionally screw the provided long M6 bend screw. Later on it will be adjusted properly. After the final adjustment the rubber cup of the old screw should be reused on the new one.

This is the bottom screw, which has to be adjusted in the bottom position: It is held with the original 14mm flat nut. Order of fitting: - Fit the lever to the motor shaft.

- Lift the headlight body in its highest position by hand lever and rod should be in a straight line. - Now tighten the nut on the lever (el. motor) as much as possible in this position.

To adjust the screws correctly, you need to move the headlight body to its highest and lowest positions with the red screw on the headlight motor.

5 This is the bottom screw, which has to be adjusted in the bottom position: It is held with the original 14mm flat nut. Order of fitting: - Fit the lever to the motor shaft. - Fit the nut, but don t tighten yet. The upper position of the headlight has to be fixed before this. - Connect the RETRACTOR fuse. - Lift the headlight up with the button in the center console. - Lift the headlight body in its highest position by hand lever and rod should be in a straight line. - Now tighten the nut on the lever (el. motor) as much as possible in this position. Once the nut is holding the body relatively well, you can turn to red motor cup to help yourself screwing it from a better position. To adjust the screws correctly, you need to move the headlight body to its highest and lowest positions with the red screw on the headlight motor. It is hidden behind the black cap on top of the motor. You would optimally adjust them to have slight push, when in furthest positions to ensure a very stable fix and no shake. After adjustment tighten the screws at the back and refit the black cups. Installation of the headlight body Having everything assembled you need now to reinstall the body using the two side screws and M6 nuts. Make sure you have reconnected the height adjustment connector on the side of the body. Once reinstalled you will end up with this and need now to connect loose end of the push rod with the lever to the el.motor: Now you have installed the headlights and need to ensure they are in the correct height. The tolerances are very narrow due to the extreme low profile of the lights. How to check the position: - Lights popped up: the bottom of the headlight (not the black frame) is above the top edge of the bumper. - Lights down: The headlight lid slips in and falls below the bonnet/bumper. The rods come pre-adjusted, however if adjustment is needed, you need to remove the nut from the headlight motor shaft and change the distance between the ball joint is steps of 1 rotation in the desired direction. Longer distance will have longer low-to-high-travel, means they will go down lower and pop up higher. Reducing the space between the ball joints has the opposite effect. After all is adjusted and fitted back in place you should connect the power connector to the headlight (its plug and play to the stock connector). Adjust the lid in height as a next step as used with the stock headlights. Installation of the side panels Once everything is done so far you can install the black side panels. As a general rule, the panels should be approx. 1mm away from the headlight. This allows the movement of the adjustable headlight.

6 The inner panel is held with 13mm black self tapping screws at the back and 19mm one at the front. At the front it needs the plastic spacer (10mm) on the inner side to keep its parallel position. The outer panel is held with two 13mm long screws. Additional 6mm washer is provided to allow fine adjustment if needed. Headlight adjustment You should have installed everything correct if reached to this point. Before adjusting the headlights you should check the function of the retractors and height adjustments. After attaching the Hella rectangle headlights to the adaptor frames, they will need adjustment, just like the stock ones. To do this you have various options: 1. The two upper screws provided on the Hella frames are there for adjustment, both horizontal and vertical. Please make sure the lights are not only vertically aligned, but also having parallel output. 2. The adapter frames are pivoting on the upper screws with the springs. The bottom screw acts as the adjustment screw on the stock ones. You can use this one as well for the adjustment if needed. It would be wrong to assume it has to be fully screwed down, as it would be on the stock ones. 3. You can adjust the pushing rod, by unscrewing it with steps of 1 turn. This will adjust the height, but will also help to adjust the lift height (in case you want them to be higher or lower). A thumb rule is, that the bottom of the light (not the frame), should be above the water level of the upper bumper edge. Another very important point is the very good adjustment of the stopper screws. They might look not very important in a first place, but they are the ones, that are holding the headlight in its upper and lower position and not the motor with the pushrod. They effectively prevent the shake effect of the not well fixed in position headlight. Make sure in these both positions the headlight frame is pushed via the stopper bolt to the corresponding bracket to prevent this while driving. Now take a break and enjoy the new vision of your roadster. With regards, Jass Performance!

JK FRONT FENDER FLARE INSTALLATION INSTRUCTIONS

JK FRONT FENDER FLARE INSTALLATION INSTRUCTIONS TOOLS NEEDED 3/16 Allen Wrench 1/2 Socket or wrench 10mm Socket Flat head screwdriver HARDWARE 5/16 x 3/4 button heads (14) 5/16 x 1 button heads (8) 5/16