Vll. Apply sealant Important. Instructions of Installation. Tools for installation. To apply sealant onto

Transcription

1 Precautions TS-/TS- Never allow a child, a senile people or a people who is difficult in moving about to enter the shower box alone; Never climb on the overhead shower box or hang heavy weight on it. To avoid damage to the overhead shower box, never use hard matter to rub or knock at it. Never put a burning cigarette near the bottom tray or bathtub or drop cigarette ash on bottom tray or bathtub lest a fire is caused or they would be damaged. When you enter the overhead shower box, to avoid falling down, be careful with the height difference between the floor and the bottom tray. When you enter the overhead shower box, to avoid injury, never put your hand in the door gap. Maintain sufficient ventilation from the overhead shower box to prevent Soapsuds is usually present on accumulation of moisture in it, giving the surface of the overhead shower rise to mildew breeding and abnormal box, be careful to avoid slip and fall. odor. To clean the bathtub, liquid detergent and a piece of soft fabric should be used. Strong acidic or alkaline detergent, thinner, acetone, ammonia, organic solvent, or strong cleanser should never be used. top shower series If water scale is formed on the bathtub or bottom tray, use a piece of wet soft fabric applied with some tooth paste to rub it off. If glass cement falls off, leaking of water is likely. So it is necessary to re-apply. Maintain the bottom tray clean to avoid blocking of the drain port by hairs, dirt, etc. For Top Shower Box and Use

2 Vll. Apply sealant Important Installation shall be carried out strictly to the instructions for installation, otherwise the shower box would be unreliably installed or would even collapse, leading to injury or damage to property. Unpack the cargo box and check that nothing is missing. Reliably place the glass panels vertically against the wall. If placed horizontally, they would break easily. Special cacumen on not to het the four angles of the glass door. After checking and adjustment, apply neutral glass cement in the gap between the bottom tray, the side post and the wall. The glass panels should be handle vertically by two people. Never knock at the glass panels forcefully lest they would be broken. To apply sealant onto Before using the product, read these instructions carefully and keep them in a safe place Tools for installation φ percussion drill bit Tape measure Level gauge Percussion drill Plumb Glass cement gun Hexagonal socket screw Steel hammer Pencil Rubber hammer Cross-head screw driver Product standard followed: Q/(GZ)ABJK Shower Box 0

3 Construction of TS-/TS-(direct type) Door handle grip Stud Rubber washer Door handle grip Rubber washer () Fix the door handle to the movable door. Vl. Check and adjust After installation, check if the shower box body is vertical and the movable door opens freely. Adjust the rollers and the side post properly to ensure that the movable door opens freely. No. Checking and adjustment 0 RV- magnetic sealing strip RV- sealing strip Bottom tray 0 Side post and inner sheath TM- sealing strip # door handle Qn'ty STx0 pan head self-tapping screw STx0 pan head self-tapping screw Drain hose Expansion shield 0 φ big washer 0 Overall dimensions:ts mm TS mm

4 Vl. Install movable door Construction of TS-/TS-(reverse type) Hexagonal nut Eccentric nut Up guide rail Eccentric nut Installation and adjustment of upper roller ()Adjust the eccentric nuts on the upper and lower rollers so that the distance between them is equal to that between the channel of upper guide rail and the channel of the lower guide rain. ()Hang the upper rollers of the moving door in the channel of the upper guide rail then insert the lower rollers in the channel of the lower guide rail. ()Adjust the eccentric nuts on the upper and lower guide rails so that the moving door slides freely and the door gap is even. Tighten the locknuts. RV- sealing strip RV- sealing strip No. 0 RV- magnetic sealing strip RV- sealing strip Bottom tray 0 Side post and inner sheath TM- sealing strip # door handle Installation and adjustment of movable door ()Slide the two RV- sealing strips over the left edge of the fix door glass panel and the right edge of the moving door glass panel respectively. ()Slide one RV- magnetic sealing strip over the left edge of the moving door glass panel. Qn'ty STx0 pan head self-tapping screw STx0 pan head self-tapping screw Down guide rail Drain hose Expansion shield 0 φ big washer 0 Moving door Roller Overall dimensions:ts mm TS mm Installation and adjustment of lower roller RV- magnetic sealing strip Eccentric nut Side post Roller

5 IV. Install shower box body I.Install the bottom tray Big washer ()Use 0 STx0 pan head self-tapping screws andφ big washer to fix the two inner sheathes onto the wall on each side. Install and adjust the bottom tray ( ) Turn the rubber-headed foot bolt to adjust for levelness of the bottom tray. Tighten the locknut. () Slide the large end of drain pipe hose over the drain elbow. () Insert the small end of the drain hose in the drain port in the floor. Installation and adjustment of shower box body Side post Bottom tray Note: The inner diameter of drainpipe should be larger than oufer diameferof drain hose. Otherwise water can not go fleetly. ()Use two ST 0 pan head self-tapping screws to fix the lower guide rail to the bottom tray ()Place the assembled shower box body on the bottom tray so that the two side posts catch the two inner sheathes. () Position the bottom tray in the room corner. ()Use level gauge to check for levelness of the bottom tray.

6 II. Construction of Fixed doot Ill. Marking and drilling # post Lower guide rail TM- sealing strip # post # post ()Use four STx0 pan head self-tapping screws to fix the two side posts to the lower guide rail. ()Use a pencil to mark out a straight line each along both sides of the inner sheath. Marking and drilling glass Pictures of How the fixed door is Constructed Self-tappingscrew ()Place the assembled shower box body on the bottom tray. Perform plumbing and check that the box body is perpendicular to the bottom tray. Side post Door fixer ()Place the fix door glass panels on the right ends of the lower guide rail so that the lower edge of each fix door glass panel enters the groove of the door holder, the side of each fix door glass panel enters the groove of the # post. Tighten the pan head self-tapping screws on the door holders so that the lower edges of the fix door glass panels are fixed to the two door holders. # post Upper guide rail () Place the upper guide rail on the top of the fix door glass panels so that the upper edges of the fix door glass panels enter the grooves of the door holders on the upper guide rail. Use four STx0 pan head self-tapping screws to fix the upper guide rail to the two # side posts. Tighten the two pan head self-tapping screws on the door holders so that the top of the two fix door glass panels is fixed to the door holders. ()Squeeze one TM- sealing strip in the gap between the fix door glass panel and the # post. ()Take out the inner sheath from inside the side post. ()Press the inner sheath onto the wall. Use a pencil to mark out on the wall the positions of connecting holes of the inner sheath. ()Drill five φ holes each on either sides in the wall as marked. ()Drive 0 expansion shields in theφ holes in the wall on each side.