SC72-220S24 Technical Specification

Transcription

1 Key Features Size: (in) AC input range:90~265vac Single outputs:24v/3.0a High efficiency:85% Line regulation: ±2% Load regulation: ±2% Low ripple&noise: 100mV short circuit Output over Input over Over temperature Natural cool Product Overview Applications This AC-DC converter use advanced power processing, Communications control and packaging technologies to provide the Industry control performance, flexibility, reliability and cost effectiveness of workstations... a mature power component. High frequency switching... provides high power density with low noise and high efficiency. V00 Page 1 of 5

2 1. Electric Characteristics 1.1 Input Characteristics Rated input Vac AC input range Vac AC input frequency range Hz Input inrush current 60 A Max. input,25, first start Efficiency % Rated input, rated load 1.2 Output Characteristics Output range Vdc Output current range 0 3 A Line Regulation ±2 % Load Regulation ±2 % Voltage stabilizing precision ±2 % Temperature Regulation ±0.02 % / C Over operating temperature range Ripple & noise 100 mv Dynamic response Deviation ±5 % Settling time 20 MHz bandwidth. output with 10uF electrolytic capacitor and 0.1uF ceramic capacitor at full rated current. 25% to 50% to 25% Iout max, 50% to 75% to 50% Iout max, 2.5A/us 300 us To within 1% Vout nom. Turn-on delay time 8 s 220Vac, Full load Output overshoot ±5 % Output Capacitance 1000 μf TTL signal 3 12 V High level, output ok V Low level, output fail 1.3 Protection Characteristics Protect Input over Vac Recovery Vac Output over Vdc Constant Short Circuit Protection 10 mω Hiccup Over-temperature Required to restart V00 Page 2 of 5

3 2. General Characteristics MTBF 100 KHrs Rated input, full load,25 3. Environmental Characteristics Operating temperature Storage temperature Relative humidity 5 95 % Storage humidity % Altitude 3000 m Atmospheric pressure KPa 4. Safety Characteristics Isolation Input to 1500 Vac output 10mA/1min, No arcing and breakdown Input to 1500 Vac ground Output to 500 Vdc 10mA/1min, No arcing and breakdown ground Isolation Input to 500Vdc/1min, normal atmospheric 10 MΩ resistance output pressure, 90% humidity Leakage Input to 1.5 ma 240Vac,normal condition current ground 5. EMC Characteristics Item Standards Conditions Notes CE EN55022 Class B Pass system test RE EN55022 Class B Pass system test Harmonic Voltage fluctuations and flicker Surge DIP EN EN EN EN EN55024 C type lamps requirements Class A equipments requirements Differential mode ±2KV,common mode±4kv 0%Ut,10ms, test at phase 0, 90, 180 and V00 Page 3 of 5

4 40%Ut, 20ms 70%Ut,50ms ESD Air EN ±8KV discharge Contact EN ±4KV discharge Notes: Criterion A: Normal performance during and after test. : Low- or reset is not allowed. Temporary output fluctuation ceases after disturbances ceases, and from which the EUT recovers its normal performance automatically. During the system test, output fluctuation or reset is not allowed too. Criterion C: Temporary loss of output is allowed, but the hardware can t be damaged. The EUT recovers its normal performance automatically or operator intervention. Criterion R: Loss of output which is not recoverable is allowed. The primary protective component (fuse) can be damaged. The EUT recovers its normal performance after replace the damaged component. 6. Physical Information 6.1 Mechanical Outline Length width heigth: (in), , , V00 Page 4 of 5

5 6.2 Connector designations Pin No. Name Function 1 VO+ Positive output 2 GND Negative output 3 TTL TTL signal 4 N AC input 5 L AC input 6 FG The earth Application Notes: A variety of application notes and technical white papers can be downloaded in pdf format from our website. ENARGY POWER (SHENZHEN) CO.,LTD. Enargy Power US Office Tel: (86) Add: 8th Floor, Block 8, South Honghualing Industry Zone, Xili, Shenzhen, China Tel: (925) Fax: (925) Add: 2303 Camino Ramon, Suite 130, San Ramon, C A V00 Page 5 of 5