DRA-60 SERIES 60 Watt LED Power Supply Measures: 3.94 x 3.54 x 1.57 LPS (866) MEAN WELL

Transcription

1 Bauart gepruft Sicherheit egelma ge od o s be wac g www. tuv.com ID MEAN WE PS

2 SPECIFICATION MODE DRA DRA DC VOTAGE CONSTANT CURRENT REGION RATED CURRENT 12V 3 ~ 12V 5A 24V 3 ~ 24V 2.5A CURRENT RANGE RATED POWER 0 ~ 5A 60W 0 ~ 2.5A 60W OUTPUT RIPPE & NOISE (max.) Note.2 120mVp-p 150mVp-p VOTAGE ADJ. RANGE 12 ~ 15V 24 ~ 30V VOTAGE TOERANCE Note.3 ±1.0% ±1.0% INE REGUATION OAD REGUATION SETUP, RISE TIME Note.4 0ms, 90ms/230VAC 800ms, 90ms/115VAC at full load HOD UP TIME (Typ.) 50ms/230VAC 10ms/115VAC at full load VOTAGE RANGE FREQUENCY RANGE 90 ~ 264VAC 47 ~ 63Hz 127 ~ 370VDC [DC input operation possible by connecting AC/(+), AC/N(-)] INPUT EFFICIENCY (Typ.) 85% 87% AC CURRENT (Typ.) 1.3A/115VAC 0.8A/230VAC INRUSH CURRENT (Typ.) COD START 30A/115VAC 60A/230VAC 95 ~ 108% rated output power PROTECTION OVEROAD Protection type : Constant current limiting, recovers automatically after fault condition is removed OVER VOTAGE ~ 18.63V ~ 37.26V Protection type : Shut down o/p voltage, re-power on to recover WORKING TEMP. WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION -30 ~ +70 (Refer to "Derating Curve") 20 ~ 90% RH non-condensing - ~ +85, 10 ~ 95% RH ± 0.03%/ (0 ~ 50 ) on output 10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes SAFETY STANDARDS U , TUV EN approved SAFETY & WITHSTAND VOTAGE I/P-O/P:3KVAC I/P-FG:2KVAC O/P-FG:0.5KVAC EMC ISOATION RESISTANCE I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25 / 70% RH (Note 5) EMC EMISSION Compliance to EN55022 (CISPR22) Class B, EN ,-3 EMC IMMUNITY Compliance to EN ,3,4,5,6,8,11, EN55024, EN , light industry level, criteria A OTHERS NOTE MTBF DIMENSION PACKING 436.4K hrs min. MI-HDBK-217F (25 ) *90*100mm (W*H*D) 0.3Kg; 42pcs/13.6Kg/0.82CUFT

3 Block Diagram I/P EMI RECTIFIERS & POWER SWITCHING RECTIFIERS & O.C.P. +V -V FG O..P. CONTRO DETECTION CIRCUIT O.V.P. Derating Curve Static Characteristics VAC Input only OAD (%) 20 OAD (%) (VERTICA) AMBIENT TEMPERATURE ( ) INPUT VOTAGE (V) 60Hz ED DIMMING/OUTPUT CURRENT ADJUSTMENT OPERATION Built in 3 in 1 ED dimming function or output current adjustment. Output constant current level can be adjusted by applying 1 ~ 10Vdc, 10V PWM signal or resistance between and. Please DO NOT connect "" to "-V". Reference resistance value for output current adjustment (Typical) Resistance value Single driver Multiple drivers (N=driver quantity for synchronized dimming operation) 10KΩ 20KΩ 30KΩ 60KΩ 10K Ω/N 20K Ω/N 30K Ω/N K Ω/N 50K Ω/N 60K Ω/N 70K Ω/N 80K Ω/N 90K Ω/N 100K Ω/N % 20% 30% % 50% 60% 70% 80% 90% 100% 102%~108% 1 ~ 10Vdc for output current adjustment (Typical) Applied Source 1V 2V 3V 4V 5V 6V 7V 8V 9V 10V 10% 20% 30% % 50% 60% 70% 80% 90% 100% KΩ 50KΩ 10V PWM signal for output current adjustment (Typical): Frequency range :100Hz ~ 3KHz Duty value 10% 10% 20% 20% 30% 30% % % 50% 50% 60% 60% 70KΩ 70% 70% 80KΩ For ED dimming operation, direct connection to EDs is suggested, but is not suitable for using additional drivers. 80% 80% 90KΩ 100KΩ 90% 90% 100% 100% 102%~108% 102%~108%

4 Using the built-in dimming function can't turn the lighting fixture totally dark. Please refer to the connection method below to achieve 0% brightness of the lighting fixture connecting to the ED power supply unit. Using a switch and relay can turn ON/OFF the lighting fixture. OAD 10K~100K Ohms resistance 1~10V DC Voltage 10V PWM Signal Adjuster +V +V -V -V + +V ADJ Switch N Relay FG N DRIVING METHODS OF APPICATIONS INVOVING ED The power supply may either work in "constant voltage mode or constant current mode" to drive the EDs. Rated output voltage (A) Constant Voltage area (B) Constant Current area In the constant current region, the highest voltage at the output of the driver depends on the configuration of the end systems. Should there be any compatibility issues, please contact MEAN WE. 3V Vo(v) (C) Hiccup Protection Io (%)

5 35 MEAN WE Mechanical Specification Case No.962A Unit:mm V +V -V -V V ADJ N Installation Instruction This series fits DIN rail TS35/7.5 or TS35/15. For installation details, please refer to the USER MANUA on (This diagram is for reference. The rail is not included with unit.) Back View File Name:DRA--SPEC