UNISONIC TECHNOLOGIES CO., LTD

Transcription

1 UNISONIC TECHNOLOGIES CO., LTD IC FOR HEADPHONE STEREOS DESCRIPTION The LAG665 is a monolithic integrated circuit, designed for was use in headphone stereos, and incorporates dual preamp, power amp, electronic VR and motor control circuits. It can be used in a simple circuit configuration which requires very few external components. FEATURES *1-Chip stereo tape recorder with motor speed controller. *Operating supply voltage range: V CC =2~5V *Good volume control ORDERING INFORMATION Ordering Number Package Packing LAG665FG-S28-R SOP-28 Tape Reel MARKING 1of 8 Copyright 2015 Unisonic Technologies Co., Ltd

2 PIN CONFIGURATION VB PRE 1 28 GND PRE 1 IN IN+ 1 IN IN- 1 NF PRF NF PRE 1 OUT PRE OUT PRE ATT ATT 2 CON VOL 7 22 PRE OFF V REF 8 21 V CCPRE 1 OUT P 9 20 V CC GND P OUT P V BP MO OFF GND MD V CCMO V CON CON T MO ON CON S PIN FUNCTION DESCRIPTIONS PIN NO. SYMBOL DESCRIPTION 1 VB PRE Pre Amp Bias Voltage 2 1 IN+ Channel 1 + Input 3 1 IN - Channel 1 - Input 4 1 NF PRE Feedback OUT PRE Pre Amp Output 1 6 ATT 1 Attenuator 1 7 CON VOL Volume Control 8 V REF Reference Voltage 9 1 OUT P Power Amp Output 1 10 GND P Power GND 11 V BP Power Amp Bias Voltage 12 GND MD Motor GND 13 V CON Motor Control Voltage 14 MO ON Motor Forced Start 15 CON S Speed Control 16 CON T Torqul Control 17 V CCMO Motor Power Control 18 MO OFF Motor Forced Stop 19 2 OUT P Power Amp Output 2 20 V CC Supply Voltage 21 V CCPRE Supply Voltage 22 PRE OFF Pre Amp Off 23 ATT 2 Attenuator OUT PRE Pre Amp Output NF PRE Feedback IN- Channel 2 - Input 27 2 IN+ Channel 2 + Input 28 GND PRE Pre GND UNISONIC TECHNOLOGIES CO., LTD 2 of 8

3 BLOCK DIAGRAM Pre Amp Attenuator Power Amp Motor Control 1/2 Vcc Bias Control V/I 1/2 Vcc Power Amp Pre Amp Attenuator Power Amp UNISONIC TECHNOLOGIES CO., LTD 3 of 8

4 ABSOLUTE MAXIMUM RATINGS (T A =25 C, unless otherwise specified) PARAMETER SYMBOL VALUE UNIT Supply Voltage V CC -0.3~+7.5 V Power Dissipation P D 450 mw Operating Voltage V OP 2~5 V Operating Temperature T OPR -20~+65 C Storage Temperature T STG -40~+125 C Note: Absolute maximum ratings are those values beyond which the device could be permanently damaged. Absolute maximum ratings are stress ratings only and functional device operation is not implied. ELECTRICAL CHARACTERISTICS (V CC =6V,T A =25 C, unless otherwise specified) PARAMETER SYMBOL TEST CONDITIONS MIN TYP MAX UNIT Supply Current I CC V IN =0V, I M =0mA ma PRE-AMPLIFIER (V CC =3.0V, f=1khz) Open Loop Gain G VO V O =-10dBm, R L = 72 db Close Loop Gain G VC V O =-10dBm db Maximum Output Voltage V OM THD=10% V RMS Total Harmonic Distortion THD V OUT =400mV Rms % Output Noise Voltage V ON V IN =0, R G =2.2k, BPF(30~20kHz) μv RMS Input Impedance Z IN V OUT =-10dBm kω Cross Talk between CH CT R G =2.2k, V OUT =-10dBm 30 db Output Voltage when Pre-Off V O_OFF V IN =100mV Rms -50 db Output Impedance when Pre-Off R O_OFF 10 kω Input Impedance when Pre-Off R I_OFF 10 KΩ Attenuator (V CC =3.0V, f=1khz, R L =16Ω) Maximum Input Voltage V I_MAX 0.2 V RMS Maximum Attenuation V A_MAX V CONT =Min 66 db Attenuation Error V AERR V CONT =Max 0 db Input Impedance Z IA kω Control Ternimal Input Impedance Z ICOT 100 kω Power Amplifier (V CC =3.0V, f=1khz, R L =16Ω) Voltage Gain GV P OUT =5mW db Channel Voltage Difference GV V CONT =Max 0 3 db Maximum Output Power I P OM 1 THD=10%, R L =32Ω mw Maximum Output Power II P OM 2 THD=10%, R L =16Ω 30 mw Total Harmonic Distortion THD P OUT =5mW % Cross Talk between CH C T P OUT =5mW db Output Noise Voltage V ON R G =2.2k, V CONT =Min mv RMS Ripple Rejection RR V CC =3V, 100Hz, 100mVp-p db Pre + Pulse Boost + Power Noise V NTO V IN =0V, R G =2.2k, V CONT =Max 6 9 mv RMS UNISONIC TECHNOLOGIES CO., LTD 4 of 8

5 ELECTRICAL CHARACTERISTICS (V CC =6V,T A =25 C, unless otherwise specified) PARAMETER SYMBOL TEST CONDITIONS MIN TYP MAX UNIT Motor Comtrol (V CC =3V, I M =100mA) Current Consumption IMC 3 5 ma Starting Current IMS 500 ma Reference Voltage V REF Pin 15~Pin V Reference Voltage Change I V REF 1 V CC =2.1~5V (Note) 0.05 %/V Reference Voltage Change II V REF 2 I M =25~250mA 0.01 %/ma Reference Voltage Change III V REF 3 T A =-10~50 C 0.01 %/ C Current Factor K Current Factor Change I K1 V CC =2.1~5V 0.5 %/V Current Factor Change II K2 I M =25~250mA 0.05 %/ma Current Factor Change III K3 T A =-10~50 C 0.02 %/ C Saturation Voltage at Forced ON V CESA I M =200mA, Pin 14=V CC 0.6 V Input Impedance at Forced ON Pin R ION 5.6 KΩ Leakage Current at Forced OFF IML 200 μa Input Impedance at Forced OFF Pin R ICON 33 KΩ Note: Voltage across pins 13 and 19 (motor pins) fluctuates. UNISONIC TECHNOLOGIES CO., LTD 5 of 8

6 TEST CIRCUIT UNISONIC TECHNOLOGIES CO., LTD 6 of 8

7 SWITCH MATRIX SW No. TEST CONDITION ITEM SYMBOL V CC =3V, f=1khz, 1 2 3, R L =16Ω AMP Supply Current I CC c c a b b a b b b a a I M =0mA, V R =max Close Loop Gain G VC b b b b b a b b b a a V O =-10dBM Maximum Output Voltage V OM b b b b b a b b b a a THD=10% Total Harmonic Distortion THD b b b b b a b b b a a V O =400mV Output Noise Voltage V ON c c b b b a b b b a a B.P.F.(20~30kHz) Cross Talk between CH Output Voltage when Preamp Off Attenuator Maximum Input Voltage Maximum Attenuation C T b/c c/b b b b a b b b a a V O =244mV, V O =-10dBM V O_OFF b b b a b a b b b a a V IN =100mV RMS V I_MIX a a a a b a b b b a a V A_MAX a a a a b a b b b a a V R =Mid, THD=10% Difference in V O output when V R =max. and output voltage when V R =min Power AMP Voltage Gain GV a a a a b a b b b a a P OUT =5mV Channel Voltage Difference Maximum Output Power I Maximum Output Power II Total harmonic distortion ratio Crosstalk between channels GV a a a a b a b b b a a P OM 1 a a a a b b a b b a a P OM 2 a a a a b a b b b a a Channel output difference at V R =max R L =32Ω, THD=10% R L =16Ω, THD=10% THD a a a a b a b b b a a P OUT =5mW C T a/c c/a a a b a b b b a a P OUT =5mW measured with channels swapped output voltage when V R =min Output noise voltage V N c c a b b a b b b a a V R =min Ripple Rejection RR c c b a b a b b b a b V R =max Pre+power noise V NTO c c a b b a b b b a a V R =max Consumption current I MC c c a a b a b a b a a I M =0mA Startup current I MS c c a a b a b a b b a Reference voltage VREF c c a a b a b a b a a I M =100mA (15~16 Pin) Reference voltage fluctuation I Reference voltage fluctuation II V REF1 c c a a b a b a b a a V REF2 c c a a b a b a b a a I M =100mA, V CC =2.1~5.0V (13~17 Pin) V CC =3.0V, I M =25~250mA UNISONIC TECHNOLOGIES CO., LTD 7 of 8

8 SWITCH MATRIX (Cont.) ITEM Output voltage on forced on Leakage current on forced off SYMBOL SW No. TEST CONDITION 1 2 3, V CC =3V, 11 f OSC =1kHz, R L =16Ω V CESA c c a a a a b a b a a I M =200mA IML c c a a b a b a a b a UTC assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all UTC products described or contained herein. UTC products are not designed for use in life support appliances, devices or systems where malfunction of these products can be reasonably expected to result in personal injury. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. UNISONIC TECHNOLOGIES CO., LTD 8 of 8