SDH/SONET Module. Features. Applications. Benefits

Transcription

1 SDH/SONET Module When paired with the rugged, battery operated T productivity test platform the T SDH/SONET Module tests SDH, SONET, PDH and T-carrier, circuits from 2.5 Gbps to 1.544/2.048 Mbps and 155M/622M ATM Networks. Both in-service and out-ofservice configurations cover installation, maintenance, and troubleshooting applications. Auto-configuration takes the guesswork out of configuring the instrument to the circuit under test. Experienced users will appreciate advanced features like overhead monitoring and control, APS timing measurement, and pointer test sequences. All measurements conform to industry standards, and circuit impairments are displayed in a variety of ways, giving operators insight into the possible causes of circuit impairments. Features SDH/SONET, PDH/T-carrier testing from 1.544/2.048 Mbps up to 2.5 Gbps Bit error ratio testing and performance analysis Pointer monitoring and test sequence generation Auto-configuration APS timing measurement Comprehensive payload mapping selection from VC4-16c/OC-48c (contiguous concatenation) to VC12/VT2, VC11/VT1.5, including PDH/T-Carrier payloads (1.5M, 2M, 34M, and 45M/DS1, E1, DS3, and T3) 155M/622M ATM Traffic Supervision with QoS measurements Histogram Analysis Applications Installation, maintenance, and troubleshooting Out-of-service testing Tx STM-16 / OC-48 Optical Ring In-service monitoring through protected monitoring points or optical splitters Tx Benefits SDH/SONET feature-rich Lightweight Flexible modular design Eliminates the need for multiple instruments Intuitive and easy-to-use Cost-effective and future-proof Part of the T forward compatibility soluion Round trip delay STM-16 / OC-48 Optical Ring SDH/SONET, PDH/T-carrier interface Through mode NE Network NE supplied and supported in the UK by Phoenix Datacom - tel: info@phoenixdatacom.com -

2 SDH/SONET specifications Operation Modes Point-to-point: Tx and are set to the same rate Through mode operation (2.5G and below) Line through Passes entire signal through with no manipulation of overhead or injection of errors or alarms SDH Optical (ITU-T G.707) Port/Connector: 2.5 Gbps/622 Mbps/155/52 Mbps (optional): SFP field interchangeable, duplex LC Rates: STM-16 (2.5 Gbps), STM-4 (622 Mbps), STM-1 (155 Mbps), STM-0 (52 Mbps) Payloads: VC4-16c, VC4-4c, VC4 Bulk, VC3 Bulk, 45M, 34M, 2M Async, 1.5M Async, VC12 Bulk, VC11 Bulk ITU-T mapping Error injection: B1, B2, B3, FASE, MS-REI, HP-REI, LP-REI, BIP-2, Bit Error injection count: Programmable error burst of 1 to 9999 Error injection rate: 2x10-3 to Alarm generation: LOS, LOF, RS-TIM, MS-AIS, MS-RDI, AU-AIS, AU-LOP, HP-PRDI, HP-SRDI, HP-CRDI, HP-UNEQ, HP-PLM, HP-TIM, LP-PRDI, LP-SRDI, LP-CRDI, LP-RFI, LP-PLM, LP-UNEQ, LP-TIM Results measurements Errors: B1, B2, B3, FASE, MS-REI, HP-REI, LP-REI, BIP-2, Bit Alarms: LOS, LOF, OOF, RS-TIM, MS-AIS, MS-RDI, AU-AIS, AU-LOP, HP-UNEQ, HP-PLM, HP-TIM, HP-PRDI, HP-SRDI, HP-CRDI, LP-RFI, LP-PLM, LP-UNEQ, LP-TIM, LP-PRDI, LP-SRDI, LP-CRDI Performance: G.821, G.826, G.828, G.829, M.2101/2110 SDH pointer: Justification, increase, decrease SONET Optical (Telcordia GR-253-CORE) Port/Connector: 2.5 Gbps/622 Mbps/155/52 Mbps (optional): SFP field interchangeable, duplex LC Rates: OC-48 (2.5 Gbps), OC-12 (622 Mbps), OC-3 (155 Mbps), OC-1/ STS-1 (52 Mbps) Payloads: STS-48c, STS-12c, STS-3c, STS-1, DS3, DS1 Async, VT1.5 Bulk Error injection: B1, B2, B3, BIP-V, Frame, REI-L, REI-P, REI-V, Bit Error injection count: Programmable error burst of 1 to 9999 Error injection rate: 2x10-3 to Alarm generation: LOS, LOF, AIS, AIS-L, RDI-L, LOP-P, AIS-P, PLM-P, TIM-P, UNEQ-P, PRDI-P, SRDI-P, CRDI-P, AIS-V, LOP-V, PLM-V, TIM-V, UNEQ-V, LOM-V, RFI-V, PRDI-V, SRDI-V, CRDI-V Results measurements GR-253 bit performance FC (failure counts), BER, LOPS (loss of pattern sync), %LOPS, SEFS (severely errored frame seconds), %SEFS, ES (errored seconds), %ES, SES (severely errored seconds), %SES, UAS (unavailable seconds), %UAS, EFS (error free seconds), %EFS SONET defects LOS, LOF, AIS-L, RDI-L, LOP-P, AIS-P, SRDI-P, PRDI-P, CRDI-P, PLM-P, TIM-P, UNEQ-P, AIS-V, SRDI-V, PRDI-V, CRDI-V, LOP-V, PLM-V, TIM-V, UNEQ-V, LOM-V, B1, B2, B3, BIP-V, Frame, REI-L, REI-P, REI-V, FC (failure counts), SEFS (severely errored frame seconds), %SEFS, ES (errored seconds), %ES, SES (severely errored seconds), %SES, UAS (unavailable seconds), %UAS, EFS (error free seconds), %EFS SONET pointer: Justification, increase, decrease Test Patterns STM-16 (VC4-16c) / OC-48 ( STS-48c SPE): , , , , , All 0s, All 1s, Alt 1010, 1-8, 1-16 STM-16 (VC4-4c and below) / OC-48 (STS-12c and below): , , , , All 0s, All 1s, Alt 1010, 1-8, 1-16 STM-4, STM-1, STM-0 / OC-12, OC-3, OC-1, STS-1: , , , , All 0s, All 1s, Alt 1010,1-8, 1-16 User: 10 user patterns defined up to 16 bits Test pattern inversion Measurements Common to SDH/SONET Continuous measurement Elapsed time Optical power level measurement Event log with timestamp Frequency: Received, max, min (freq. deviation in ppm), ± clock slips Automatic tributary scan 80 characters/line report of alarms/errors per tributary In-service and out-of-service for 1.5M (DS1), 2M (E1), 34M (E3), 45M (DS3), VC3 Bulk (STS-1 SPE), and VC4 Bulk inside STM- 0/1/4/16 and OC-1/3/12/48 with full report SDH/SONET Overhead Features Monitor and transmit section/regenerator section, line/multiplex section, and path overhead bytes ASCII decode of 16-byte or 64-byte HP/STS or LP/VT path trace bytes (J1/J2) Programming K1/K2 APS signaling bytes per ITU-T G.783/G.841 J0 Section trace generation: 1 byte SAPI format or 16 bytes E.164 ASCII sequence + CRC-7 S1 synchronization status messages decode and generation Path overhead monitor Programming of path overhead bytes J1/J2 Path trace generation: 16 bytes E.164 ASCII sequence + CRC-7 or 64 bytes E.164 ASCII sequence C2 signal label byte programming in binary or hexadecimal G1 bit 5: RDI generation User programmable path user bytes (F2, F3) Programmable K3, K4 bytes (bits 1-4) for APS signaling V5 byte: Signal label generation (bits 5-7), Extended signal label generation/decode (K4 byte), Enhanced RDI generation/detection Pointer monitor: H1, H2, V1, V2 bytes Pointer adjustment: Programming of pointer value, NDF, and SS bits Pointer test control Mode: Single Select increment, decrement, or alternate the pointer value Pointer Test Sequences AU/STS or TU/VT pointer Sequences: Single, burst, phase, transient burst, periodic, 87-3, 26-1, opposite (increase + decrease), custom Movement: Increase, decrease, increase + decrease Anomalies: Added, cancel, none Automatic Protection Switch Time Measurement Resolution: 1 ms Accuracy: 1 ms Sensors: LOS, AIS-L/MS-AIS, AIS-P/AU-AIS, AIS-V/TU-AIS, B2 Pass/Fail indicator User selectable switch and gate time 2 T SDH/SONET Module

3 APS timing at 1.5M and 2M interfaces Sensors 1.5M: LOS, LOF, AIS, Yellow 2M: LOS, LOF, AIS, FAS RAI APS bytes capture Capture and decode states of K1/K2 bytes Store hundreds of messages Ring and linear decoding 125 μs resolution Optional trigger with wildcards Timestamp in frames or ms Duration in absolute or elapsed time Save or print results Load and decode past results APS bytes capture Capture and decode states of K1/K2 bytes Store hundreds of messages Ring and linear decoding 125 μs resolution Optional trigger with wildcards Timestamp in frames or ms Duration in absolute or elapsed time Save or print results Load and decode past results SFP Optical Transceivers Complies to ITU-T G.957, Telcordia GR-253-CORE Jitter compliance to ITU-T G.825 Lambda (nm) Output Power (dbm) Distance (km) Wavelength (nm) Input Sensitivity (dbm) STM-16/4/1/0, OC-48/12/3/ SR -10 to -3 < to to IR -5 to 0 < to to LR -2 to +3 < to to IR -5 to 0 < to to LR -2 to +3 < to to -9 Data rates supported: 2488, 622, 155, 52 Mbps SONET and SDH STM-4/1/0, OC-12/3/ IR -15 to -8 < to to LR -3 to +2 < to to LR -3 to +2 < to to -8 Data rates supported: 622, 155, 52 Mbps SONET and SDH Internal Mbps ± 4.5 ppm Mbps ± 4.5 ppm Gbps ± 4.5 ppm External: Synchronization to external MHz or MHz via external clock input 155 Mbps Electrical (STM-1E/STS-3) Included with T 2380SW-155E Port/Connector: 75 Ω unbalanced SMG. External clock: Bantam 100/120 Ω, Mbps, Mbps or MHz Line coding: CMI Internal: Bit rate Mbps ± 4.5 ppm External: Synchronization to external MHz or MHz via external clock input Framing: Conforms to ITU-T G.707 Mapping: Conforms to ITU-T G.707 Payloads VC4 Bulk, VC3 Bulk, VC12 Bulk, VC11 Bulk, 45M, 34M, 2M Async, 1.5M Async Framed, unframed Frequency recovery range: Mbps ± 50 ppm Terminate: 12.7 db cable loss Jitter tolerance: Conforms to ITU-T G.825 Impedance: 75 Ω unbalanced 52 Mbps (STS-1) Port/Connector: 75 Ω unbalanced BNC (f) Line coding: B3ZS Internal: Bit rate Mbps ± 4.5 ppm Pulse shape: Conforms to Telcordia GR-253 Framing: Conforms to ITU-T G.707 Annex A Frequency recovery range: Mbps ± 50 ppm Terminate: 10.8 db cable loss Monitor: +3 db to 26 db resistive loss Impedance: 75 Ω unbalanced PDH/T-Carrier Specifications 45 Mbps (DS3, T-Carrier) Port/Connector: 75 Ω unbalanced BNC (f) Line coding: B3ZS Internal: Bit rate Mbps ± 4.5 ppm Framing: Unframed, M13, and C-bit Error injection: Code, Bit, Frame, C-bit, P-bit, FEBE Alarm generation: AIS, Yellow, Idle Frequency recovery range: Mbps ± 50 ppm Terminate: Up to -6 db cable loss Monitor: -20 db resistive loss plus -6 db cable loss Jitter tolerance: Conforms to Telcordia GR-499-CORE Impedances Terminate: 75 Ω unbalanced Monitor: 75 Ω unbalanced 34 Mbps (E3, PDH) Port/Connector: 75 Ω unbalanced BNC (f) Line coding: HDB3 3

4 PDH/T-Carrier Specifications (continued) Internal: Bit rate Mbps ± 4.5 ppm Framing: Framed, unframed, structured per ITU-T G.742, G.751 Error injection: Code, Bit, FAS Alarm generation: AIS, FAS RAI Frequency recovery range: Mbps ± 50 ppm Terminate: 12 db cable loss Monitor: -20 db resistive loss plus -12 db cable loss Jitter tolerance: Conforms to ITU-T G.823 Impedance: 75 Ω unbalanced 2 Mbps (E1, PDH) Port/Connector: 100/120 Ω balanced RJ-45 (f) External clock: Bantam 100/120 Ω, Mbps, Mbps or MHz Line coding: AMI, HDB3 Internal: Bit rate Mbps ± 4.5 ppm External: Mbps or MHz for balanced (120 Ω) interfaces Framing: Unframed, PCM-30, PCM-30C, PCM-31, PCM-31C conforms to ITU-T G.704 Error injection: Code, Bit, CRC-4, E-bit, FAS Alarm generation: AIS, FAS RAI, MFAS RAI Fractional E1 E1 error measurements Channel configuration verification N or M (noncontiguous) x 64 kbps, N=1 to 31 Through mode: Test pattern on selected channels; all others through Frequency recovery range: Mbps ± 50 ppm Terminate, Bridge: +6 db to -43 db with ALBO Monitor: -20 db resistive loss plus -6 db cable loss Jitter tolerance: Conforms to ITU-T G.823 Impedances Terminate: 120 Ω balanced Monitor: 120 Ω balanced Bridge: 1200 Ω Mbps (DS1, T-Carrier) Port/Connector: 100 Ω balanced RJ-45 (f) External clock: Bantam 100 Ω, Mbps, Mbps or MHz Line coding: AMI, B8ZS Internal: Bit rate Mbps ± 4.5 ppm External: Mbps Framing: Unframed, SF-D4, ESF, Conforms to ANSI T1.102, 107, 107A, 403, and 404. Conforms to Telcordia TR-TSY and TR- TSY Error injection: BPV, FBE, Logic, CRC-6, Frame Alarm generation: AIS, yellow, idle Fractional T1 T1 error measurements Channel Configuration Verification Nx64 kbps, Nx56 kbps, N=1 to 24 Through mode: Test pattern on selected channels; all others through Frequency recovery range: Mbps ± 50 ppm Terminate, Bridge: +6 db to -36 db cable loss Monitor: -15 to -25 db resistive loss plus -6 db cable loss Jitter tolerance: Conforms to Telcordia GR-499-CORE Impedances Terminate: 100 Ω balanced Monitor: 100 Ω balanced Bridge: 1000 Ω Test Patterns , , , , 2 9-1, 2 7-1, 2 6-1, All 0s, All 1s, Alt 1010, 20ITU, 55 Octet, 55 Daly, QRS*, 1-8, 1-16 (*Not available on T3/E3), 3-24 User: 10 user patterns defined up to 32 bits Test pattern inversion PDH/T-Carrier Measurements DS1, E1, E3, DS3 Error type Code (BPV), FBE, P-bit, C-bit, FEBE, CRC-6 (DS1, DS3) Code, Bit, FASE (E1, E3) CRC-4, E-bit (E1) Typical error type reports: Total error count, error rate, ES, %ES, SES, %SES, UAS, %UAS, EFS, %EFS, AS, %AS ITU-T G.821 analysis ITU-T G.826 analysis: Based on anomalies, defects, far end indications M.2100 analysis (Maintenance or BIS) Alarm statistics Loss of signal seconds, loss of frame seconds, AIS seconds FAS RAI seconds (2M, 34M) MFAS RAI seconds (2M only) Yellow alarm seconds (1.5M, 45M) Low density seconds, excess 0s seconds (1.5M) Frequency measurements: Moving bar graph of slip count, max frequency, min frequency, frequency deviation in ppm, clock slips 4 T SDH/SONET Module

5 Histogram Analysis Common to SDH, SONET, PDH and T-carrier Errors/Alarms/Pointer graphic display in real-time Stores current results with 1-second resolution for the last 60 minutes, 1-minute resolution for the last 72 hours, and 15-minute resolution for the last 57 days Multiple User Profiles Up to 10 different test configuration profiles may be saved Test profiles saved and loaded with the press of a button Profiles can be shared across multiple chassis for fast and efficient test set configuration and operation Upload and download test results from realgate Results and Reports Test reports can be saved in PDF format for easy retrieval, sharing, and analysis of data. Upload and download test results from realgate View test results in realgate Remote web access option allow users to drive all RXT SDH/SONET s testing capability from a remote location using any computing device with industry-standard web browser (requires RXT1000SW-REM) ATM Testing Mapping (SDH): HEC-based per ITU-T G.707 (mapping using VC4) Interface: UNI and NNI per ITU-T I.361 Header control: GFC, VPI/VCI, PTI, CLP Scrambling: On or off Idle cells: Idle or null C2 POH Hex: 13 (default) Pattern truncate Display: VPI/VCI in decimal or hexadecimal ATM cell LED indicates presence of valid ATM cells OAM cell generation VCC scan: 128 independent headers AAL 0/1/2/5 generation and analysis Quality of Service Timed or continuous measurement Programmable start time and date Traffic Supervision 8 independent VCC filters: 1 foreground, 7 background Foreground: Full QoS, BERT, OAM counter, and statistics Background: Traffic statistics and OAM monitoring only Quality of Service: Errored cells and CER, lost cells and CLR, misinsertedcells and CMR ATM alarms: VP-/VC-LOC, AIS, RDI, LFMF (segment, end-to-end) Global measurements: Total cells, idle cells, HEC errors (correctable and non-correctable), HEC rate Delay Measurements: Cell Transit Delay (CTD) (MEAN, MIN, and MAX) and Cell Delay Variation (CDV) Peak to Peak 2-point (MAX, MIN) Requires timestamp field or O.191 Test Cell Total, congested, tagged count and rate Cps (cells per second) Bit errors and bit error rate, CRC errors OAM cell count: F4/F5, segment/end-to-end, AIS/RDI/loopback OAM count: Continuity check, Performance management Graphical display in histogram format of Bit Errors, CHEC, NCHEC, cell loss seconds, cell errors and OAM cell count (F4/F5, segment/ end-to-end, AIS/RDI, loopback) VCC Scan Up to 128 independent headers: GFC, VPI, VCI, PTI, CLP, AAL type AAL scan Save up to 8 VCC configurations Utilization % Traffic Generation 8 independent VCCs: 1 foreground, 7 background Foreground VCC Traffic: Constant Bit Rate (CBR), Unspecified Bit Rate (UBR) Burst/Variable Bit Rate (VBR) and Sequential Cells Cell type: User, O.191 Test Cell, OAM-B Cell Performance Patterns: 223-1, 220-1, 215-1, All 1s, All 0s, and 16-bit user patterns Background VCCs Traffic: CBR Cell type: User Patterns: 16-bit user patterns AAL 0 Traffic: CBR, VBR/UBR, Sequential Cells Patterns: 223-1, 220-1, 215-1, All 1s, All 0s, and 16-bit user patterns PCR: %, Mbps, Cps AAL 2 Length CID (Channel Identifier) Traffic: CBR, VBR/UBR, Sequential Cells Patterns: 223-1, 220-1, 215-1, All 1s, All 0s, and 16-bit user patterns PCR: %, Mbps, Cps AAL 5 CPCS-UU (Common Part Convergence Sublayer-User to User) indication number CPI (Common Part Indicator) Frame rate: 0-50 Error injection: Bit, HEC, and NC-HEC errors, burst and rate Alarm generation: F4/F5, segment/end-to-end, AIS, RDI, loopback, continuity check Product Description Size: W x 152 L x D 30 mm (8.2 W 6.0 L 1.2 H in) Module Weight: kg (1.9 Lb) Environmental: Operating Temperature:....0 to 40 C (32 to 104 F) Storage Temperature: to 70 C (-4 to 158 F) Humidity: % to 90% non-condensing 5

6 Ordering Information T T 2.5G - SDH/SONET Test Set 1.5M, 2M, 34M, 45M and 52Mbps Test Set with RJ45 connector for 1.5M/2M and BNC connectors for 34M/45M/52M. Offers Performance (BER) Test, Histogram Analysis, Pointer Test Sequences, APS Switching Timing,Tandem Connections Monitoring. Includes: T Platform (RXT1000A-GW), T Carrier (RXT2000A), SDH/SONET Module (SSMTT-38), stylus (SA142), hand and shoulder straps, Li-ion battery pack (SA991), AC/DC charger (SA1580), soft carrying case (SA605), calibration statement, and one year basic warranty. T2380-EW T test set Warranty Extension: 1 Additional Year T2380-EW T test set Warranty Extension: 2 Additional Years Software Options T2380SW-155ME 155M Electrical Interface Testing (STM-1e). Includes one 155M Electrical SFP with SMG(F) Connectors, 75 ohm. (SA326 Conversion cables are recommended. Requires 2 cables per SFP Module) T2380SW-155M. 155M/52M Optical Interface Testing (STM-1/0, OC-3/1) Requires SA581 or SA582 series SFPs. T-2380SW-622M 622M/155M/52M Optical Interface Testing (STM-4/1/0, OC-12//3/1) Requires SA581 or SA582 series SFPs. T-2380SW-25G. 2.5G/622M/155M/52M Optical Interface Testing (STM-16/4/1/0 OC-48/12/3/1) Requires SA581 series SFPs. T2380SW-155MA 155M ATM Testing RXT2380SW-622MA 622M ATM testing SFP Transceiver Options SA IR M/155M/52M, 1310 nm Intermediate Reach SA LR M/155M/52M, 1310 nm Long Reach SA LR M/155M/52M, 1550 nm Intermediate Reach SA SR G/622M/155M/52M, 1310 nm Short Reach Tx/ SFP, LCUPC/SMF Connector SA IR G/622M/155M/52M, 1310 nm Intermediate Reach SA LR G/622M/155M/52M, 1310 nm Long Reach SA IR G/622M/155M/52M, 1550 nm Intermediate Reach SA LR G/622M/155M/52M, 1550 nm Long Reach Recommended Accessories SA Optical Patch Cord, SMF, LC-SC duplex, 6 SA Optical Patch Cord, SMF, LC-FC duplex, 6 SA Conversion Cable, BNC(m) 75 ohm to SMG(m) 75 ohm, 6. Note: Certain limitations apply, contact support for details and availability For more information or supplied a directory and supported of sales offices: in the UK Phone: by Phoenix Datacom or tel: info@sunrisetelecom.com info@phoenixdatacom.com I Sunrise Telecom Incorporated. All rights reserved. Specifications subject to change without notice. All product and company names are trademarks of their respective corporations. Sunrise Telecom San Jose and Taiwan facilities are ISO 9001 certified. Do not reproduce, redistribute, or repost without written permission from Sunrise Telecom. T SDH/SONET Module Data Sheet C_0202 Rev.C01, December 14, 2011