10G SFP+ Transceiver FOSPP3110L2C. Features. Applications. Compliance. Up to 2km transmission distance. Support Multi Rate

Transcription

1 FP+ Transceiver FOPP3110L2C Features Up to 2km transmission distance upport Multi Rate Gbps 1310nm FP and PIN receiver FI electrical interface 2-wire interface for integrated Digital Diagnostic monitoring FP+ MA package with duplex LC connector Hot pluggable Very low EMI and excellent ED protection +3.3V power supply Power consumption less than 1 W Operating case temperature: 0~+70 C Applications High-speed storage area networks Computer cluster cross-connect Custom high-speed data pipes LTE optical repeater application Compliance Compliant with Fiber Channel(FC)-tandard INCIT 352 Compliant with IEEE 802.3ae-2002 Compliant with FCC 47 CFR Part 15, Class B Compliant with FDA 21 CFR and , Class I except for deviations pursuant 1 / 13

2 Description FOPP3110L2C is a high performance, cost effective modules, which is supporting Multi Rate Gbps, and transmission distance up to 2km on M fiber. The transceiver consists of two sections: The transmitter section incorporates a 1310nm FP driver and re-timer. The receiver section consists of a PIN photodiode integrated with a transimpedance preamplifier (TIA). The module is hot pluggable into the 20-pin connector. The high-speed electrical interface is base on low voltage logic, with nominal 100 Ohms differential impedance and AC coupled in the module. The optical output can be disabled by LVTTL logic high-level input of TX_DI. Transmit Fault (Tx_Fault) is provided to indicate that the module transmitter has detected a fault condition related to laser operation or safety. Loss of signal (RX_LO) output is provided to indicate the loss of an input optical signal of receiver. A serial EEPROM in the transceiver allows the user to access transceiver monitoring and configuration data via the 2-wire FP Management Interface. This interface uses a single address, A0h, with a memory map divided into a lower and upper area. Basic digital diagnostic (DD) data is held in the lower area while specific data is held in a series of tables in the high memory area. pecification Absolute Maximum Ratings Parameter ymbol Min. Max. Unit torage Temperature T upply Voltage V CC V Relative Humidity RH % Rx Input Average Power Pmax - 0 dbm Recommended Operating Conditions Parameter ymbol Min. Typical Max. Unit Operating Case Temperature T C Power upply Voltage V CC V I CC ma Power Dissipation P D W Data Rate Gbps Transmission Distance Km Transmitter Operating Characteristic-Optical, Electrical Parameter ymbol Min. Typical Max. Unit Note Center Wavelength λ C nm Note1 Laser Off Power Poff dbm Average Optical Power Pavg dbm Note1 Extinction Ratio ER db Transmitter Dispersion Penalty TDP db 2 / 13

3 Relative Intensity Noise Rin db/hz Optical Return Loss Tolerance db Operating Data Rate Gbps Optical Eye Mask Compliant with IEEE 802.3ae Note2 ingle Ended Output Voltage Tolerance V Common Mode Voltage Tolerance mv Tx Input Diff Voltage VI mv Tx Fault VoL V At 0.7mA Data Dependent Input Jitter DDJ UI Data Input Total Jitter TJ UI Notes: [1] Average optical power shall be measured using the methods specified in TIA/EIA [2] Vertical eye closure penalty and stressed eye jitter are the test conditions for measuring stressed receiver sensitivity. They are not the required characteristic of the receiver. Receiver Operating Characteristic-Optical, Electrical Parameter ymbol Min. Typ. Max. Unit Note Center Wavelength λr nm Receive ensitivity In Average Power Psens dbm Receiver ensitivity In OMA dbm Note1 tressed Receiver ensitivity In OMA dbm Note1 Los Assert LosA dbm Los Dessert LosD dbm Los Hysteresis LosH db Overload Pin dbm tressed Eye Jitter UIp-p Receiver electrical 3dB upper cutoff frequency GHz Vertical Eye Closure Penalty db Note2 Receiver Reflectance db Operating Data Rate Gbps ingle Ended Output Voltage Tolerance V Rx Output Diff Voltage Vo mv Rx Output Rise and Fall Time Tr/Tf ps 20% to 80% Total Jitter TJ UI Deterministic Jitter DJ UI Notes: [1] Receiver sensitivity is informative. tressed receiver sensitivity shall be measured with conformance test signal for BER =1x [2] Vertical eye closure penalty and stressed eye jitter are the test conditions for measuring stressed receiver sensitivity. They are not the required characteristic of the receiver. 3 / 13

4 Control and tatus I/O Timing Characteristics Parameter ymbol Min. Max. Unit Note TX Disable Assert Time t_off - 10 µs Note1 TX Disable Negate Time t_on - 1 ms Note2 Time to initialize including reset of TX_Fault t_init ms Note3 TX Fault Assert Time t_fault µs Note4 TX Disable to Reset t_reset 10 - µs Note5 LO Assert Time t_loss_on µs Note6 LO Deassert Time t_loss_off µs Note7 Rate-elect Change Time t_ratesel - 10 µs Note8 erial ID Clock Rate f_serial_clock khz Notes: [1] Time from rising edge of TX Disable to when the optical output falls below 10% of nominal [2] Time from falling edge of TX Disable to when the modulated optical output rises above 90% of nominal [3] From power on or negation of TX Fault using TX Disable [4] Time from fault to TX fault on [5] Time TX Disable must be held high to reset TX_fault [6] Time from LO state to RX LO assert [7] Time from non-lo state to RX LO deassert. [8] Time from rising or falling edge of Rate elect input until receiver bandwidth is in conformance with appropriate specification Optical Characteristics(Multi Rate Characteristics) Parameters 1.25G [1] 2.5G 4.95G 6.25G Total power consumption <1W <1W <1W <1W Tx light output power >-8.2 >-8.2 >-8.2 >-8.2 Extinction ratio >3.5 >3.5 >3.5 >3.5 Eye mask margin >20% >20% >20% >20% Rx sensitivity <-22.0dBm <-20.0dBm <-17.0dBm <-16.0dBm Working temperature 0~+70C 0~+70C 0~+70C 0~+70C Notes: [1] For 1.25G data rate, the modules performance is compatible with 1G FC application but not fully compliant. If customer needs to fully compliant with 1.25G data rate specifications, we need to implement Rate-election function, please contact our sales team for detailed information. 4 / 13

5 Pin-out Definition Pin Assignment Figure1 Pin Logic ymbol Name/Description Note 1 VeeT Module Transmitter Ground Note1 2 LVTTL-O TX_Fault Module Transmitter Fault Note2 3 LVTTL-I TX_Disable Transmitter Disable; Turns off transmitter laser output Note3 4 LVTTL-I/O DA 2-wire erial Interface Data Line (ame as MOD-DEF2 as defined in the INF-8074i) Note4 5 LVTTL-I/O CL 2-wire erial Interface Clock (ame as MOD-DEF1 as defined in the INF-8074i) Note4 6 MOD_AB Module Absent, connected to VeeT or VeeR in the module Note5 7 LVTTL-I R0 Not used 8 LVTTL-O RX_LO Receiver Loss of ignal Indication (In FC designated as RX_LO, in ONET designated as LO, and in Ethernet designated at ignal Detect) 9 LVTTL-I R1 Not used Note2 10 VeeR Module Receiver Ground Note1 11 VeeR Module Receiver Ground Note1 12 CML-O RD- Receiver Inverted Data Output 13 CML-O RD+ Receiver Non-Inverted Data Output 14 VeeR Module Receiver Ground Note1 15 VccR Module Receiver 3.3 V upply 16 VccT Module Transmitter 3.3 V upply 5 / 13

6 17 VeeT Module Transmitter Ground Note1 18 CML-I TD+ Transmitter Non-Inverted Data Input 19 CML-I TD- Transmitter Inverted Data Input 20 VeeT Module Transmitter Ground Note1 Notes: [1] The module signal ground pins, VeeR and VeeT, shall be isolated from the module case. [2] This pin is an open collector/drain output pin and shall be pulled up with 4.7k-10kohms to Host_Vcc on the host board. Pull ups can be connected to multiple power supplies, however the host board design shall ensure that no module pin has voltage exceeding module VccT/R V. [3] This pin is an open collector/drain input pin and shall be pulled up with 4.7k-10kohms to VccT in the module. [4] ee sff wire Electrical pecifications. [5] This pin shall be pulled up with 4.7k-10kohms to Host_Vcc on the host board. Block Diagram of Transceiver Figure2 Transmitter ection The transmitter converts bit/s serial PECL or CML electrical data into serial optical data compliant with the BAE-LR standard. An open collector compatible Transmit Disable (Tx_Dis) is provided. A logic 1, or no connection on this pin will disable the laser from transmitting. A logic 0 on this pin provides normal operation. The transmitter has an internal automatic power control loop (APC) to ensure constant optical power output across supply voltage and temperature variations. An open collector compatible Transmit Fault (Tx_Fault) is provided. TX_Fault is a module output contact that when high, indicates that the module transmitter has detected a fault condition related to laser operation or safety. The TX_Fault output contact is an open drain/collector and shall be pulled up to the Vcc_Host in the host with a resistor in the range kω. TX_Disable is a module input contact. When TX_Disable is asserted high or left open, the FP+ module transmitter output shall be turned off. This contact shall be pulled up to VccT with a 4.7 kω to 10 kω resistor 6 / 13

7 Receiver ection The receiver converts bit/s serial optical data into serial PECL/CML electrical data. An open collector compatible Loss of ignal is provided. Rx_LO when high indicates an optical signal level below that specified in the relevant standard. The Rx_LO contact is an open drain/collector output and shall be pulled up to Vcc_Host in the host with a resistor in the range kω, or with an active termination. Power supply filtering is recommended for both the transmitter and receiver. The Rx_LO signal is intended as a preliminary indication to the system in which the FP+ is installed that the received signal strength is below the specified range. uch an indication typically points to non-installed cables, broken cables, or a disabled, failing or a powered off transmitter at the far end of the cable. Recommended Interface Circuit Figure3 7 / 13

8 Dimensions Figure4 8 / 13

9 Table 1: Key Mechanical Dimensions Digital Diagnostic Memory Map 9 / 13

10 EEPROM Information (A0h) Field ize Addr. (Bytes) Name of Field Hex Description 0 1 Identifer 03 FP FP function is 1 1 Ext. Identifier 04 defined by serial ID only 2 1 Connector 07 LC Connector Transceiver 00 Transceiver Codes 11 1 Encoding BR, Nominal Mb/s 13 1 Rate Identifier 00 Unspecified 14 1 Length (9um) km 02 Transceiver transmit distance,10km 15 1 Length (9um) 100m 14 Transceiver transmit distance,10km 16 1 Length (50um)10m 00 Transceiver transmit distance 17 1 Length (62.5um) 10m 00 Transceiver transmit distance 18 1 Length (Copper) 00 Not compliant 19 1 Length (50um OM3) 00 Not compliant Vendor name E HG GENUINE 4E Vendor Name(ACII) 36 1 Reserved Vendor OUI Vendor PN 4D D MTR-1E20-01 Part 30 2D No.(ACII) Vendor rev 31 2E (ACII) Wavelength 05 1E Transceiver wavelength 62 1 Reserved CC_BAE 40 Check code for Base ID Fields Options 00 1A TX_DIABLE, TX_FAULT and Loss of ignal implemented BR,MAX 00 Not pecified 67 1 BR,MIN 00 Not pecified Vendor N N(Variable) erial Number of 10 / 13

11 transceiver(acii) Date code DC(Variable) Manufactory Date Code. Digital diagnostic monitoring 92 1 Diagnostic Monitoring implemented, 68 Type Internally calibrated is implemented Optional Alarm/Warning flags implemented for all monitored quantities, Optional oft TX_Disable control 93 1 Enhanced Options F0 and monitoring implemented, Optional oft TX_FAULT monitoring implemented, Optional oft RX_LO monitoring implemented 94 1 Includes functionality FF_ described in Compliance Rev9.3 FF CC_EXT C(Variable) Check sum for Extended ID Field Vendor pecific Read only Depends on customer information Filled by zero Reserved Read only Filled by zero 11 / 13

12 Ordering Information Part No. Pack Rate Tx Pout Rx TEMP Reach Other FOMPP810L03C FP+ 850nm VCEL -8.2~0.6dBm PIN -11.1dBm 0~70 300m FOPP3110L1I FP+ 1310nm FP -8.2~0.5dBm PIN -14.4dBm -40~85 1.4km FOPP3110L2I FP+ 1310nm FP -6.5~-0.5dBm PIN -14.4dBm -40~85 2km FOPP3110L2C FP+ 1310nm FP -8.2~0.5dBm PIN -14.4dBm 0~70 2km FOPP3110L10I FP+ 1310nm DFB -8.2~0.5dBm PIN -14.4dBm -40~85 10km FOPP3110L10C FP+ 1310nm DFB -8.2~0.5dBm PIN -14.4dBm 0~70 10km FOPP3110L20C FP+ 1310nmFP -3~+2dBm PIN -14.4dBm 0~70 20km FOPP3110L20I FP+ 1310nm DFB -3~+2dBm PIN -14.4dBm -40~85 20km FOPP3110L40I FP+ 1310nm DFB -1~+3dBm PIN -16dBm -40~85 40km FOPP3110L40C FP+ 1310nm DFB -1~+3dBm PIN -16dBm 0~70 40km FOPP5510L40I FP+ 1550nmEML -1~+2dBm PIN -15.5dBm -40~85 40km FOPP5510L40C FP+ 1550nmEML 0~4dBm PIN -15.8dBm 0~70 40km FOPP5510L80C FP+ 1550nmEML 0~+4dBm APD -23dBm 0~70 80km FOPP5510L100 C FP+ 1550nmEML +1~+4dbm APD -26dbm 0~70 100km Contact Information FiberOutlets.com Address: Building E3, Floor 17, NO.1702 Optical Valley oftware Park, East Lake High-tech Development Zone, Wuhan, P.R.C. Wuhan, Hubei Province, , China Tel: Fax: market@fiberoutlets.com Website: fiberoutlets.com tatement 12 / 13

13 FiberOutlets possesses the authority for ultimate explanation of all information contained in this document, which is subject to change without prior notice. All the information was obtained in specific environments; and FiberOutlets will not be responsible for verifying the products performance in customers operating environments, neither liable for the performance of users' products. All information contained is only for the users' reference and shall not be considered as warranted characteristics. FiberOutlets will not be liable for damages arising directly or indirectly from any use of the information contained in this document. Publishing Date: Copyright FiberOutlets All Right Reserved 13 / 13