DSP VOICE PROCESSOR II
|
|
- Cordelia Burns
- 5 years ago
- Views:
Transcription
1 HAM RADIO WORKS DSP VOICE PROCESSOR II User and installation manual
2 1. About the module DSP Voice Processor 2 is a compact PCB module indented for voice equalization. The compact size (only 29x29mm) allows it to be installed direct to the hand mike as Yaesu MH-31 for example. It is compatible typically with any transceiver like Yaesu (FT-817, FT-857, FT-897, FT-450/D, FTdx-1200, FTdx-3000 and so on) or Elecraft K2 (special pre-programmed Plug And Play version is available)! Main functions is: - 8 band bi-quad filter equalizer; - Built-in voice AGC with programmable gain, output level and time constants; - Fast and linear Noise Gate feature with programmable parameters; - 3D effect with programmable depth and delay; - Two instant switching settings profile; - Two independent mike inputs: one for condenser mike and one for dynamic mike; - Wide dynamic range output attenuator from 0 (maximim) to -72dB (minimum) MS Windows (XP, Vista, 7, 8) programming software with drivers package is available. All the settings stored in the internal flash of DSP processor. Module can be powered from the power which routed to the transceiver microphone connector.
3 2. DSP Voice Processor 2 signals. OUT (ground) Profile OUT + ELECTRET MIC PWR - DYN MIC MIC GND PWR + DSP Voice Prosessor module is intented for direct installation into Yaesu MH-31 hand mic. It uses internal +5V power of the mic connector. Signals name and description: PWR +, PWR - Power. Red +, Black - ; Profile For instant settings profile switching. It is pulled up to the internal module power via 10kOhm resistor. Pull this signal to ground to select Profile 2 and leave it unconnected to select Profile 1; OUT +, OUT - Audio output. Green Audio output, Black Audio ground should be connector to the common ground; ELECTRET MIC Electret microphone input; DYN MIC Dynamic microphone input; MIC GND Microphone ground;
4 3. Programmable parameters and settings. Output gain Programmable output attenuator. Values from 0 to -72dB. Mic select Mic type selection. ELEC electret type (comes with DSP Voice Processor 2); DYN dynamic type. AGC enable Mic AGC on/off. Max. gain If mic AGC is enabled this setting defines maximum AGC gain applied to the selected mic input and defines the audio compression level. If mic AGC is disabled this parameter defines linear mic gain of the selected mic input; Target level Mic AGC target level. The level which AGC is trying to achieve during mic signal amplification. -10dB is recommended normal setting.
5 Attack time AGC attack time. Time needed to decrease AGC gain in case of input mic level become high. 8ms is normal setting. Decay time Time needed to increase AGC gain in case of input mic level become low. 100mS is normal setting. Noise threshold Noise level at which Noise Gate is active (mute audio output). Hysteresis level Noise Gate hysteresis. This setting needed to prevent Noise Gate cycle switching. 3dB is normal setting. Detection debounce time Noise Noise detection delay. Detection debounce time Signal Voice signal detection delay. Clip stepping Normally this setting is not used. If enabled mic ADC (Analog to Digital Converted) will decrease its gain each cycle by 0.5dB to prevent ADC overload. Echo depth Echo effect depth (10 to 30% is normal setting). Echo delay Echo effect delay.
6 4. Using with ELECRAFT K2 To achieve good audio sounding make a SSBA = 1 and SSBС = 1-1 settings in your rig. Control mic gain by Output gain and Max Gain of the DSP Voice Processor Using with Yaesu FT-8x7 rigs Make a SSB MIC gain from 10 to 15. Control mic gain by Output gain and Max Gain of the DSP Voice Processor Using with Yaesu FTdx-1200/3000 rigs Set SSB MIC level in range from 10 to 15, compressor to Technical parameters. Supply voltage from 3.5 to 15V DC; Constant DC current 25mA; PCB Dimensions 29x29mm.
7 Yaesu MH-31 installation. Reassemble Yaesu MH-31. For that unscrew two short and one long screws. Remove PCB. Unscrew three little screws. Unsolder from PCB dynamic capsule (white and brown). Find C1 capacitor and R1 resistor. Remove it carefully. Unsolder two tinned wires from Tone ½ switch SW5; Do not overheat contacts of SW5! Left contact of SW5 solder by a wire to 2 nd contact of RJ-45. Left contact SW5 Right contact Remove Middle contact R1 C1 Connect left contact of SW5 with 2nd contact of RJ-45 connector. RJ-45 SW
8 DSP Voice Processor comes with 1500uF electrolytic condenser. Place this condenser between SW5 switch and RJ-45 connector. Bend capacitor contacts to other side of PCB. SW5 + _ 1500uF Profile RJ-45 Bend capacitor contacts to other side of PCB. Prolong capacitor Plus contact by a wire and solder it to 6 th contact of RJ-45 connector. Minus contact of the capacitor solder to 2 nd contact of RJ-45 connector, Capacitor Plus Capacitor Minus SW5 switch Solder signal Profile to the middle contact of SW5 switch. Solder PWR signals to 2 nd and 6 th contacts of the RJ-45 connector. PWR + Red PWR - Black
9 OUT+ and OUT- signals solder to the microphone pads. PTT signal solder to the 3 rd contact of the RJ-45 connector. Short by a solder contacts of the former C1 holes. OUT + Green OUT - Black Solder short С1 holes Assemble back Yaesu MH-31.
Beta-test ED1 PCB installed in I0CG s K1
K1 SSB Modification (Ed.2) This description provides the receiver (RX) modifications, assembly, alignment and operation as a first step. In a second step you can add the remaining transmitter (TX) modifications,
More informationSound Engineering Solutions
Sound Engineering Solutions bhi NEDSP1061 Noise Reduction Module Yaesu FT-817 Version Fitting Instructions bhi 1061-104D Issue B Page 1 1. Introduction. The bhi NEDSP1061 noise reduction module is a fully
More informationSound Engineering Solutions
Sound Engineering Solutions bhi NEDSP1061 Noise Reduction Module Yaesu FT-817 Version Fitting Instructions bhi 1061-104D Issue B Page 1 1. Introduction. The bhi NEDSP1061 noise reduction module is a fully
More informationMAINTENANCE MANUAL AUDIO AMPLIFIER BOARD 19D904025G1 (MDR) AUDIO AMPLIFIER BOARD 19D904025G2 (MDX)
A MAINTENANCE MANUAL AUDIO AMPLIFIER BOARD 19D904025G1 (MDR) AUDIO AMPLIFIER BOARD 19D904025G2 (MDX) TABLE OF CONTENTS DESCRIPTION............................................... Page Front Cover CIRCUIT
More informationLogiTALKER OWNER S MANUAL. Voice Keyer. Idiom Press. PO Box 1015, Merlin, OR USA
LogiTALKER Voice Keyer OWNER S MANUAL Idiom Press www.idiompress.com PO Box 0, Merlin, OR -0 USA + -- Preface Thank you for purchasing our LogiTALKER, a stand-alone voice keyer for your radio. To put the
More informationDante Kit MEB 114-S. Thanks to its rugged housing and its high-quality microphone capsule the MEB 114-S ensures the best speech intelligibility.
PRODUCT SPECIFICATION 1/6 FEATURES Great speech intelligibility Phantom power via PoE Remote controllable gain level Daisy-chaining possible DELIVERY INCLUDES 1 SL DI 4 XLR Dante interface 4 MEB 114-S
More informationVERSATILE AUDIO AGC CIRCUIT Dave Kenward G8AJN
VERSATILE AUDIO AGC CIRCUIT Dave Kenward G8AJN Whilst we spend many happy hours perfecting our video signals, the audio often tends to be an afterthought. For our local repeater a finely adjustable compressor/limiter
More informationJUMA-TRX2 DDS / Control Board description OH2NLT
JUMA-TRX2 DDS / Control Board description OH2NLT 22.08.2007 General Key functions of the JUMA-TRX2 DDS / Control board are: - provide user interface functions with LCD display, buttons, potentiometers
More informationThe ME 36 is a condenser microphone capsule. This mini shotgun microphone features for an outstanding background noise rejection.
PRODUCT SPECIFICATION 1/6 FEATURES Great speech intelligibility via PoE Remote controllable gain level Daisy-chaining possible DELIVERY INCLUDES 1 SL DI 4 XLR Dante interface 4 MAT 133-S tablestands 4
More informationLED S METER CONSTRUCTION MANUAL. LED S meter Construction Manual Issue 1.0 Page 1
LED S METER CONSTRUCTION MANUAL LED S meter Construction Manual Issue 1.0 Page 1 Important Please read before starting assembly STATIC PRECAUTION The LED S Meter kit contains components which can be damaged
More informationDante Kit MEG FEATURES DELIVERY INCLUDES PRODUCT VARIANTS
PRODUCT SPECIFICATION 1/6 FEATURES Great speech intelligibility Phantom power via PoE Remote controllable gain level Daisy-chaining possible DELIVERY INCLUDES 1 SL DI 4 XLR Dante interface 4 MAT 133-S
More informationMAINTENANCE MANUAL AUDIO MATRIX BOARD P29/
MAINTENANCE MANUAL AUDIO MATRIX BOARD P29/5000056000 TABLE OF CONTENTS Page DESCRIPTION................................................ Front Cover CIRCUIT ANALYSIS.............................................
More informationBUXCOMM 2007 RASCAL GLX OPERATOR S MANUAL Before we begin, let s perform the initial setup:
BUXCOMM 2007 RASCAL GLX OPERATOR S MANUAL Before we begin, let s perform the initial setup: Sound Card CONFIGURATION: Most soundcards use 3.5mm (1/8") jack for line and/or microphone input. Use the LINE
More informationTI RigExpert. User s manual. USB Transceiver Interface
TI-5000 RigExpert USB Transceiver Interface User s manual . Table of contents Introduction Operating the TI-5000 Front and rear panels Transceiver and computer connection Updating the firmware Annexes
More informationDX Connection. QSK 2500 Instruction Manual. 1) Description. 2) Specifications.
DX Connection QSK 2500 Instruction Manual 1) Description The DX Connection QSK 2500 allows operating a non-qsk amplifier in QSK mode (or SSB mode) with no amplifier modifications. No amplifier T/R relay
More information12kHz LIF Converter V2.43 9Mhz version
12kHz LIF Converter V2.43 9Mhz version Please Note: This document supersedes all previously released documents and drawings on the LIF subject. This is the latest and most up-to-date document at this time.
More informationOBSOLETE. Microphone Preamplifier with Variable Compression and Noise Gating SSM2165
a FEATURES Complete Microphone Conditioner in an 8-Lead Package Single +5 V Operation Preset Noise Gate Threshold Compression Ratio Set by External Resistor Automatic Limiting Feature Prevents ADC Overload
More informationDX Connection. QSK 2500 Instruction Manual. 1) Description. 2) Specifications.
DX Connection QSK 2500 Instruction Manual 1) Description The DX Connection QSK 2500 allows operating a non-qsk amplifier in QSK mode (or SSB VOX mode) with no amplifier modifications. No amplifier T/R
More informationAirlite 62. By Billy GM0OBX. Got a question?...drop me an
Airlite 62 Making these work for your amateur radio transceiver By Billy GM0OBX WWW.GM0OBX.CO.UK Got a question?...drop me an email: gm0obx@yahoo.co.uk If you have managed to secure yourself a set of Airlite
More information301 & 601 Mic/Line Mixers Operation Manual
301 & 601 Mic/Line Mixers Operation Manual Biamp Systems 9300 S.W. Gemini Drive Beaverton, OR 97008 USA +1.503.641.7287 www.biamp.com 301 & 601 TABLE OF CONTENTS Introduction Front Panel Rear Panel Remote
More informationMAINTENANCE MANUAL DESKTOP STATION INTERCONNECT BOARD 19D904448G1
MAINTENANCE MANUAL INTERCONNECT BOARD 19D904448G1 TABLE OF CONTENTS Page DESCRIPTION.................................................... 1 CIRCUIT DESCRIPTION..............................................
More informationUser s Guide. INFRARED CLASSROOM SYSTEM IRR-40P RECEIVER IRN-10 MIC/TRANSMITTER IRH-15c MIC/TRANSMITTER IRD-60 EXTERNAL SENSOR
SPECIFICATIONS IRR-40P 2-channel receiver w/power amplifier Sub-carrier frequencies 2.06MHz & 2.56MHz Type Super heterodyne crystal controlled Modulation FM Pilot Tone Signal 32.768kHz Frequency Response
More informationDATASHEET. Product Features. IntriCon.com. Suitable for a Wide Range of Applications. Dynamic Contrast Detection 2-channel Compression
DATASHEET Product Features Suitable for a Wide Range of Applications Cost-sensitive digital mable hearing instruments Trimmer-controlled hearing instruments Analog replacement Product line consolidation
More informationDX Connection. QSK 2500 Instruction Manual. 1) Description. 2) Specifications.
DX Connection QSK 2500 Instruction Manual 1) Description The DX Connection QSK 2500 allows operating a non-qsk amplifier in QSK mode with no amplifier modifications. No amplifier T/R relay interface is
More informationLynx. RoIP Gateway DISPATCH LYNX MOBILE. Optional serial ports provide remote control of radio configuration over the VoIP network.
LYNX MOBILE Lynx DISPATCH RoIP TM SYSTEM Gateway LYNX TM ROIP GATEWAY OVERVIEW The Lynx system provides Radio over IP (RoIP) communications interoperability between radio base stations and VoIP networked
More informationPage 1 of 6 Page 1 of 12 Yaesu FT-5100/FT-5200 MODS Rev B (14 Apr 1993) This is a collection of hardware and software mods for the Yaesu 5100/5200 pair. I have the 5100, so I can't verify these for the
More informationRIGblaster standard models M8, M4, RJ
RIGblaster standard models M8, M4, RJ rig to sound card interfaces OWNER S MANUAL 4TH EDITION IF YOU CAN'T FIND IT HERE GO TO OUR SUPPORT PAGE: http://www.westmountainradio.com/support.htm West Mountain
More informationSome info for FT90. Serial Numbers
Some info for FT90 Serial Numbers For all Yaesu/Vertex radios that I've seen, the serial numbers are in the format of YPXXXXXX where "Y" is the production year, "P" is the production run and "XXXXXX" is
More informationStep by Step Building PJ meter ARDF Receiver Kit. CRKITS.COM August 5, 2013
Step by Step Building PJ-80 80-meter ARDF Receiver Kit CRKITS.COM August 5, 2013 What is ARDF? ARDF is the abbreviation of Amateur Radio Direction Finding, or so called Fox Hunting. If you are looking
More informationALX-SSB Transceiver Kit Assembly Manual
ALX-SSB Transceiver Kit Assembly Manual 20 August 2018 REV A Transceiver This radio is based on the popular CS-Series SSB Transceiver Kit developed by Adam Rong, BD6CR/4 CRKITS.com. Thanks to B. Bartosh
More informationHT-1A Dual Band CW QRP Transceiver. Kit Building Instructions
HT-A Dual Band CW QRP Transceiver Kit Building Instructions Rev B, July 8, 08 Designed by BD4RG Exclusively distributed by CRKITS.COM and its worldwide distributors Join the group http://groups.io/g/crkits
More informationLow Voltage Microphone Preamplifier with Variable Compression and Noise Gating SSM2167
Low Voltage Microphone Preamplifier with Variable Compression and Noise Gating SSM267 FEATURES PIN CONFIGURATION Complete microphone conditioner in a 0-lead package Single 3 V operation Low shutdown current
More informationZLS38500 Firmware for Handsfree Car Kits
Firmware for Handsfree Car Kits Features Selectable Acoustic and Line Cancellers (AEC & LEC) Programmable echo tail cancellation length from 8 to 256 ms Reduction - up to 20 db for white noise and up to
More informationK2 SSB Modifikation. A compilation of the mods suggested by John, KI6WX, Karl-Heinz, DF7KHK and Frank, DJ3FR by DL2FI
DL-QRP-AG K2 SSB Modifikation A compilation of the mods suggested by John, KI6WX, Karl-Heinz, DF7KHK and Frank, DJ3FR by DL2FI Vrsion: August 28.2010 QRPproject Molchstr. 15 12524 Berlin http://www.qrpproject.de
More informationPROFESSIONAL FOUR-CHANNEL AUDIO MIXER WITH DSP PROCESSOR
PROFESSIONAL FOUR-CHANNEL AUDIO MIXER WITH DSP PROCESSOR Thank you for purchasing the professional four-channel audio mixer with DSP processor! For the best results and the utmost satisfaction from your
More informationFM Audio/Squelch Board by Steve Dold, W6KCS w6kcs (at) stevedold (dot) com
FM Audio/Squelch Board by Steve Dold, W6KCS w6kcs at stevedold dot com Board hardware version 7-8 Firmware version 7.x This board connects to an FM receiver's discriminator/detector and provides squelched,
More informationCONTENTS FUNCTIONS & FEATURES...1 STANDARD ACCESSORIES...2
CONTENTS FUNCTIONS & FEATURES...1 STANDARD ACCESSORIES...2 OPTIONA ACCESSORIES...2 INSTAATION...2 GETTING ACQUAINTED...6 OW TO USE YOUR RADIO...8 SIDE SWITCES...9 ERROR CODE...10 SPECIFICATIONS...11 FUNCTIONS
More informationDevelopment of the QSX transceiver kit
Development of the QSX transceiver kit Norfolk Amateur Radio Club Wednesday 9-Jan-2019 Hans Summers, G0UPL http://qrp-labs.com QCX 5W CW transceiver kit QRP Labs CW Xcvr Introduced at YOTA 2017 summercamp
More informationModification of USB Sound Card for Asterisk app_rpt Use
Modification of USB Sound Card for Asterisk app_rpt Use First off a huge thank you to Steve for providing the original notes on how to modify a USB sound card. (http://images.qrvc.com/usbfob.pdf) These
More informationMicrophone Preamplifier with Variable Compression and Noise Gating SSM2166 *
Microphone Preamplifier with Variable Compression and Noise Gating SSM266 * FEATURES Complete Microphone Conditioner in a 4-Lead Package Single +5 V Operation Adjustable Noise Gate Threshold Compression
More informationHF SIGNALS ΜBITX. The QRP HF General Coverage Transceiver you can build. Buy Now Circuit Description Wireup Tune Up Help and Support BITX Hacks
Page 1 of 5 HF SIGNALS ΜBITX The QRP HF General Coverage Transceiver you can build Buy Now Circuit Description Wireup Tune Up Help and Support BITX Hacks ($109 USD) Page 2 of 5 The µbitx is a general coverage
More informationDX 33HP. 10 Meter Amateur Mobile Transceiver OWNER S MANUAL. Download this Manual Free of Charge at
DX 33HP SIG 1 3 TX PWR 5 7 9+30dB POWER HI NB/ANL MED LO HI LO BAND ECHO RX/TX VOL SQ MIC RF FM PA AM D/A E/B F/C ECHO TIME BAND 10 Meter Amateur Mobile Transceiver Download this Manual Free of Charge
More informationCW-ADD. Universal CW Adapter for SSB Transceivers. Assembly manual. Last updated: October 1,
CW-ADD Universal CW Adapter for SSB Transceivers Assembly manual Last updated: October 1, 2017 ea3gcy@gmail.com Updates and news at: www.ea3gcy.com Thanks for building the Universal CW Adapter kit CW-ADD
More informationHendricks QRP Kits BITX20A to BITX17A Conversion Instructions
Hendricks QRP Kits BITX20A to BITX17A Conversion Instructions 30 November 2008 Converting your BITX20A Kit to a BITX17A Kit is not all that complex. It only requires that you change crystals and some resonance
More informationInstallation... 3 Installing The Radio... 3 Ignition Noise Interference... 4 Antenna... 4 External Speaker... 4 Public Address...
TABLE OF CONTENTS CHAPTER 1 Specifications.............................................. 2 PAGE BIG RIG SERIES S 1 MOD PW R 20 0 3 SW R 40 1 5 5 60 1.5 7 10 2 9 20 80 3 30 +20 40 50 +40 100% MAX db +60
More informationC S Technology Ltd. cstech.co.uk. DTMF decoder kit with relay output, opto coupled input & Morse transpond.
C S Technology Ltd cstech.co.uk DTMF decoder kit with relay output, opto coupled input & Morse transpond. Our DTMF Opto decoder kit has one relay output offering clean contacts, and one Opto coupled input
More informationICOM IC-7200 Military
DG2IAQ Modification notes 20-Jul-2003, rev. 21. Feb. 2009 / p. 1 The famous ICOM IC-7200 is a great transceiver and I like it very much. As announced in several forums I realized that it has some (few)
More informationRead This Page First
Read This Page First If you are reading this you know the manuals are always available at QRPKITS.com. This is version 8.0 of the manual dated 4/27/2016. There is no need to print out the whole assembly
More informationICOM IC-7000 HM-151 DTMF Pad Install Courtesy Barry Mahaffey VE5BMW April 22, 2010
ICOM IC-7000 HM-151 DTMF Pad Install Courtesy Barry Mahaffey VE5BMW April 22, 2010 1. The usual if you mess this up don t blame me thing 2. Of course you know that the components you are working with are
More informationBill of Materials: PWM Stepper Motor Driver PART NO
PWM Stepper Motor Driver PART NO. 2183816 Control a stepper motor using this circuit and a servo PWM signal from an R/C controller, arduino, or microcontroller. Onboard circuitry limits winding current,
More informationHW-8-TR V3 PARTS LIST
HW-8-TR V3 PARTS LIST Qty Ref Description Markings 4C2 C3 C4 C5 Capacitor Disc.1ls.1uF 104 1 C1 Capacitor Disc.2ls.1uF 100V 104 1 QSKMOD-C92 Capacitor Electrolytic 1uF 50V 1 QSKMOD Capacitor Mylar.47uF
More informationRIGblaster plus. rig to sound card interface OWNERS MANUAL. West Mountain Radio. 4TH EDITION
RIGblaster plus rig to sound card interface OWNERS MANUAL 4TH EDITION IF YOU CAN T FIND IT HERE GO TO OUR SUPPORT PAGE: http://www.westmountainradio.com/supportplu.htm West Mountain Radio http://www.westmountainradio.com
More informationW4RT Electronics A Division of CyberAir Development Corporation 22 March For the Yaesu FT-817 & FT-817ND
W4RT Electronics A Division of CyberAir Development Corporation www.w4rt.com 22 March 2005 For the Yaesu FT-817 & FT-817ND The ONE BOARD FILTER (OBF-817) is an accessory for the YAESU FT-817 and FT-817ND.
More informationCLIO Pocket is Audiomatica's new Electro-Acoustical Multi-Platform Personal measurement system.
Release 1.5! CLIO Pocket is Audiomatica's new Electro-Acoustical Multi-Platform Personal measurement system. The system comes complete of the CLIO Pocket software (Windows and OSX native), the CLIO CP-01
More informationReceiver Performance Transmitted BW Contest Fatigue Rob Sherwood NCØ B
Receiver Performance Transmitted BW Contest Fatigue Rob Sherwood NCØ B Limitations to a better contest score may not always be obvious. Sherwood Engineering What is important in a contest environment?
More informationDX 33HML. Full Channel AM/FM Mobile Transceiver OWNER S MANUAL. Printed In Malaysia AT H PD000802
DX 33HML Full Channel AM/FM Mobile Transceiver Printed In Malaysia AT3601014H PD000802 OWNER S MANUAL TABLE OF CONTENTS Page Specification.................................... 2 Installation Location.....................................
More information75 Meter SSB Project Design by KD1JV Built by Paul Jorgenson KE7HR NSS 39382FE
75 Meter SSB Project Design by KD1JV Built by Paul Jorgenson KE7HR NSS 39382FE After completing a 75 meter DSB project (and using it underground, caving), I wanted to try building a SSB rig. I was searching
More informationbhi bhi DSP Noise Cancelling Products DSP Noise Cancelling Products NEDSP1061-PCB bhi ltd PO Box 318 Burgess Hill West Sussex RH15 9NR
DSP Noise Cancelling Products bhi bhi ltd PO Box 318 Burgess Hill West Sussex RH15 9NR tel: +44 (0)845 217 9926 fax: +44 (0)845 217 9936 sales@bhi-ltd.com www.bhi-ltd.com DSP Noise Cancelling Products
More informationGRAND STRAND AMATEUR RADIO CLUB
The GRAND STRAND AMATEUR RADIO CLUB (GSARC) Myrtle Beach SC is offering used amateur related equipment for sale. Written bids may be submitted to the GSARC up to Friday, November 23 rd, 2018. Only currently
More informationJochen Heilemann (DG2IAQ) German Amateur Radio Station. Yaesu FT-7100M Version 1.3. VHF/UHF Duoband Transceiver
Introduction I started on doing modifications of CB- and HAM-radios since 1980 at the age of 12 years. I mostly wasn t satisfied with the sound of the modulation or reception of my rigs. This is normally
More informationSX-M2 USER MANUAL. Never try to repair your SX-M2 yourself. It is partially manufactured on surface mount technology, and would require special tools.
Back to SX-M2 page Back to HOME page By buying the SX-M2 you have acquired a high quality microphone amplifier used by many professional sound engineers. This instrument has been developed to the quality
More information3 T856/857 Initial Tuning & Adjustment
M850-00 T856/857 Initial Tuning & Adjustment C3.1 3 T856/857 Initial Tuning & Adjustment The following section describes the full tuning and adjustment procedure and provides information on: channel programming
More informationMute send & receive. 4 Priority levels Bus assignable Balanced, transformer-isolated
Input Modules Models BAL2S, BRG1R, MAX1R, MIC1S, MIC2S, MIC1X, MIC2X, SAX1R, TBL1S, TEL1S, TNG1S DESCRIPTION Bogen s advanced plug-in modules provide a wide range of functions to support a variety of applications.
More informationeti Ultimate USB microphone for professional recording
eti Ultimate USB microphone for professional recording 3 Congratulations on your purchase of The Yeti, the most advanced and versatile multi-pattern USB microphone roaming the wild today. The Yeti is
More informationW2IHY PASSIVE FIXED OR VARIABLE ATTENUATOR KIT
W2IHY PASSIVE FIXED OR VARIABLE ATTENUATOR KIT C Copyright 11/14/02 W2IHY TECHNOLOGIES The W2IHY Passive Fixed / Variable Attenuator is designed to be a versatile accessory that is a necessity for the
More information5 With the transceiver off, press and hold the [F] and [V/M] keys; while holding them in, turn the radio on. Modification is now complete.
FT-897 mods View PDF mods file 1 Remove the 8 screws affixing the top panel of the transceiver and gently lift it off. 2 Carefully remove the small 2-pin speaker plug from the left rear corner of the transceiver
More informationRS cm transceiver
RS9044 70cm transceiver ATF-2 Base-unit Modification Dennis Koller (PA4DEN) Schoollaan 2 8392 NM Boyl 0622379901 / 0561421557 1 The receiver Lets start with the receiver, this is the most difficult part.
More informationPicture: Luit Popken PA0LPN Developed originally by G4WMX and GW3DIX, later improved by DK9NL. Latest improvements by DG0KW (version used by us)
The X-Phase-2 QRM-killer Picture: Luit Popken PA0LPN Developed originally by G4WMX and GW3DIX, later improved by DK9NL. Latest improvements by DG0KW (version used by us) A hobby project of the local VERON
More informationVocalMaster A Speech Processor for Low Power Operators
VocalMaster A Speech Processor for Low Power Operators Build this versatile and attractive accessory for the Yaesu FT-817 to give you more talk power. Allen Baker, KG4JJH I have had a lot of fun operating
More informationMODIFICATIONS ON HARRIS PLATINIUM BAND III SERIES. By OZ1LPR 2011 REV
MODIFICATIONS ON HARRIS PLATINIUM BAND III SERIES By OZ1LPR 2011 REV 2 2013 Modifications on Harris platinium TV transmitter After the shutdown of the old analouge TV system alot of TV transmitters became
More informationSolutions. Alpha. Manual English
Acoustic Solutions Alpha Manual English 1 Acoustic Solutions Alpha Operating Manual Contents: 1. Introduction 2. Safety Precautions 3. Controls and Connections 4. Operation Summary 5. Technical Data 6.
More informationInput Modules. Models BAL2S, BRG1R, MAX1R, MIC1S, MIC2S, MIC1X, MIC2X, SAX1R, TBL1S, TEL1S, TNG1S DESCRIPTION FEATURES
Input Modules Models BAL2S, BRG1R, MAX1R, MIC1S, MIC2S, MIC1X, MIC2X, SAX1R, TBL1S, TEL1S, TNG1S DESCRIPTION Bogen s eleven plug-in input modules provide a wide range of functions to support a variety
More informationSynthesized Base Station Transmitter
BST-75 OPERATOR S MANUAL (72-76 MHz) Synthesized Base Station Transmitter 357 West 2700 South Salt Lake City, Utah 84115 Phone: (800) 496-3463 Fax: (801) 484-6906 www.comtek.com TABLE OF CONTENTS Introduction...
More informationUniversal Tube Output Stage Installation Manual Table of Contents Universal Tube Output Stage Installation Manual...1 Specifications:...7 Mechanical:...7 Electrical Performance:...7 1 Power Supply Wiring...8
More information5U Oakley Modular Series. Dual Comparator and Gate Delay CV and Audio Processor
Oakley Sound Systems 5U Oakley Modular Series Dual Comparator and Gate Delay CV and Audio Processor PCB Issue 2 Builder s Guide V2.1 Tony Allgood Oakley Sound Systems CARLISLE United Kingdom The suggested
More informationConstruction Manual 4m-Linear-Transverter XV4-15
Construction Manual 4m-Linear-Transverter XV4-15 Holger Eckardt DF2FQ Kirchstockacherstr. 33 D-85662 Hohenbrunn 3207 Technical data exciter frequency: 21.0... 21.5 MHz RF frequency: 70.0.. 70.5 MHz supply
More informationPC to Radio Audio and Key-line Interface
PC to Radio Audio and Key-line Interface Background - This simple interface was developed to capacitive couple audio signals between a radio and PC, to provide a means of adjusting audio levels between
More informationPacific Antenna Low Pass Filter Kit
Pacific Antenna Low Pass Filter Kit Description Many basic transmitter and/or transceiver designs have minimal filtering on their output and frequently have significant harmonic content in their signals.
More information1. Technical Specifications
This document describes procedures that could result in voiding of the warranty of your radio. If these procedures are not precisely and properly carried out, it could result in a radio that does not work
More informationrig to sound card interface Owners Manual 5th EDITION
RIGblaster plus USB rig to sound card interface Owners Manual 5th EDITION Contents of Package 1-RIGblaster plus (NOTE: COVER IS LOOSE SO YOU MAY EASILY REMOVE IT TO INSTALL JUMPERS) 1- Accessory Zip Lock
More informationReceiver Performance Transmitted BW Contest Fatigue Rob Sherwood NCØ B
Receiver Performance Transmitted BW Contest Fatigue Rob Sherwood NCØ B Limitations to a better contest score may not always be obvious. Sherwood Engineering What is important in a contest environment?
More informationMinty Amp assembly instructions
Minty Amp assembly instructions Parts Required: LM386 OpAmp (included in kit) 2x 100uf (min 16v) Electrolytic Capacitors (included in kit) 0.1uf Ceramic Capacitor (included in kit) 0.047uf Ceramic Capacitor
More informationHMC1095LP4E v db LSB GaAs MMIC 6-BIT 75 Ohms DIGITAL ATTENUATOR, DC - 3 GHz. Typical Applications. Functional Diagram. General Description
v1.713 Typical Applications The is ideal for: CATV/ Sattelite Set Top Boxes CATV Modems CATV Infrastructure Data Network Equipment Functional Diagram Features.5 db LSB Steps to Power-Up State Selection
More informationSETUP and OPERATING MANUAL ADVANCED MULTI-CHANNEL VEHICLE INTERCOM SYSTEM (AMCVIS)
SETUP and OPERATING MANUAL Sept 23, 2010 Rev D ADVANCED MULTI-CHANNEL VEHICLE INTERCOM SYSTEM (AMCVIS) with DIGITAL CREW CONTROL and RADIO BRIDGING The AMCVIS was designed, manufactured and is supported
More informationBuilding and Operating: Son of Zerobeat A PIC based CW zerobeat indicator from Jackson Harbor Press
Building and Operating: Son of Zerobeat A PIC based CW zerobeat indicator from Jackson Harbor Press Ed Nisley, KE4ZNU, wrote an article published in the August, September and October of 1996 issues of
More informationRoofing Filters, Transmitted BW and Receiver Performance
Roofing Filters, Transmitted BW and Receiver Performance Rob Sherwood NCØB What s important when it comes to choosing a radio? Sherwood Engineering Why Did I Start Testing Radios? Purchased a new Drake
More informationFreeSpace IZA 250-LZ / 190-HZ TECHNICAL DATA SHEET. integrated zone amplifier. Key Features. Product Overview. Product Information.
Product Overview For background/foreground music and paging applications, the Bose FreeSpace IZA 250-LZ and IZA 190-HZ s are designed to deliver premium sound, provide simplified set up and easy daily
More informationIntriCon s multi-application DSP amplifier, ideal for a wide range of cost-sensitive hearing-aid applications.
IntriCon s multi-application DSP amplifier, ideal for a wide range of cost-sensitive hearing-aid applications. Another innovation from 2012 IntriCon Corporation Revised March 23, 2012 Specifications subject
More informationConstruction Manual 6m-Linear-Transverter XV6/10
Construction Manual 6m-Linear-Transverter XV6/10 Holger Eckardt DF2FQ Kirchstockacherstr. 33 D-85662 Hohenbrunn 2606 Technical data exciter frequency: 28... 30 MHz RF frequency: 50... 52 MHz supply voltage:
More informationLCD MULTIMETER FOR YOUR SHACK. MEASUREMENT U, I, P, Ah FOR GREEN ENERGY - WIND TURBINE, SOLAR PANELS. MEASUREMENT U, I, P, Ah, kwh
LCD MULTIMETER FOR YOUR SHACK MEASUREMENT U, I, P, Ah FOR GREEN ENERGY - WIND TURBINE, SOLAR PANELS MEASUREMENT U, I, P, Ah, kwh www.sp2dmb.cba.pl sp2dmb@gmail.com MULTIMETER - ATMEGA8 Piotr Bryl SP2DMB
More informationZM 84 Audio Mixer. User Manual. Order code: CRAM41. Audio Mixer ZM 84 AUX 3 AUX 1 AUX 2 AUX 4 MASTER 1 MASTER 2 OFF BASS BASS TREBLE TREBLE BASS BASS
ZM 84 Audio Mixer User Manual -20-10 0 +10 +20-20 -10 0 +10 +20 POWER L R 0 0 ON ZM 84 Audio Mixer AUX 4 MIC/LINE 1 MIC/LINE 1 MIC/LINE 2 MIC/LINE 3 MIC/LINE 4 THR THR +6 +10 +6 AUX 3 AUX 1 AUX 2 AUX 4
More informationLM4935 Automatic Gain Control (AGC) Guide
LM4935 Automatic Gain Control (AGC) Guide Automatic Gain Control (AGC) Overview A microphone is typically used in an environment where the level of the audio source is unknown. The LM4935 features an Automatic
More informationbhi bhi Sound Engineering Solutions from bhi Sound Engineering Solutions NEDSP1061-PCB bhi ltd 22 Woolven Close Burgess Hill West Sussex RH15 9RR
Sound Engineering Solutions Page 24 bhi bhi ltd 22 Woolven Close Burgess Hill West Sussex RH15 9RR tel: +44 (0)845 217 9926 fax: +44 (0)845 217 9936 sales@bhi-ltd.co.uk www.bhi-ltd.co.uk Sound Engineering
More informationCross-Connect Interface
Cross-Connect Interface User Manual Document #: 050-015-0036R01 November 2006 TASC Systems Inc. Langley, BC Canada Cross-Connect System User Manual Preface This document describes the installation, commissioning
More informationKWM-2/2A Transceiver THE COLLINS KWM-2/2A TRANSCEIVER
KWM-2/2A Transceiver Click the photo to see a larger photo Click "Back" button on browser to return Courtesy of Norm - WA3KEY THE COLLINS KWM-2/2A TRANSCEIVER Unmatched for versatility, dependability and
More informationVM1010. Low-Noise Bottom Port Piezoelectric MEMS Microphone Data Sheet Vesper Technologies Inc. With Wake on Sound Feature
VM1010 2018 Data Sheet Vesper Technologies Inc. Low-Noise Bottom Port Piezoelectric MEMS Microphone CES Honoree Innovation Awards 2018 Sensors Expo Winner Engineering Excellence 2017 VM1010 The VM1010
More informationKN-Q10 Assembly Manual
KN-Q10 Assembly Manual Translated by Adam Rong, BD6CR/4 with permission from Ke Shi, BA6BF Edited by Stephen, VK2RH Revision B, Oct 14, 2010 Thank you for purchasing the KN-Q10 4 Band SSB/CW Dual Mode
More informationRM Italy KL-500 PA.
Frequency HF Input energy/power 10-34 A Input power 1-15 W Input power SSB 2-30 W Output power 300 W Max Output power SSB 600 W PEP Max Mode AM-FM-SSB-CW Fuse 3x12 A Output power level 6 Size 170x295x62
More informationRIGblaster Plus II USB. rig to sound card interface OWNERS MANUAL.
RIGblaster Plus II USB rig to sound card interface OWNERS MANUAL WEST MOUNTAIN RADIO http://www.westmountainradio.com 1020 Spring City Drive, Waukesha, WI 53186 tel 262.522.6503 fax 262.522.6504 2008 West
More informationK44 Audio Splitter Board Kit
Introduction The K44 has a great CW reader but one thing that slows most folks down is connecting audio from their receiver to the K44's audio input. recommends using audio from the receiver's audio line
More information