PS224B. 4-Channel Secondary Monitoring IC. Version : A.001 Issue Date : 2007/05/17 File Name Total Pages : 10. : SP-PS224B-A.001.

Transcription

1 Version : A.001 Issue Date : 2007/05/17 File Name Total Pages : 10 : SP--A.001.doc 新竹市科學園區展業一路 9 號 7 樓之 1 9-7F-1, Prosperity Road I, Science Based Industrial Park, Hsin-Chu, Taiwan 300, R.O.C. Tel: Fax:

2 General Description is specially designed for switching power supply system. Four important functions of are the followings: over-voltage protection, over-current protection, under-voltage protection and power good signal generating. OVP/UVP (Over-Voltage/Under-Voltage Protection) monitors 3.3V, 5V and dual 12V to protect our power supply and PC, FPO/ goes to high when one of these supply voltages exceeds their normal operation voltage range. OCP (Over Current Protection) monitors IS33, IS5, IS12A, IS12B input current sense. An adjustable over-current condition composed of Iref and protection current range resistor helps users design OCP easily. An additional protection input pin provides the flexibility for design protection circuit. Power good signal generating notifies personal computer when power supply is ready or power supply is going to shutdown, therefore it can provide a reliable power supply environment. Features Over/Under-voltage protection and lock out Over-current protection and lock out Additional protection input Fault protection output with open drain output stage Open drain power good output signal for power good input Built-in 300mS power good AC on 75ms for UV/OC protection 38mS control de-bounce Wide power supply range (3.8V~16V) Special care for AC power off -1-

3 Block Diagram VS12A R1 R2 12 UV 12 OV 14uS S R Q 1MΩ FPO/ VS12B R3 R1 38mS De-bounce H : 4mS L : 4.5uS 12 UV R2 R3 12 OV VS5 R4 5 UV R5 R6 5 OV H : 75mS L : 4.5uS PGI Selection PGI VS33 R7 3.3 UV R8 3.3 OV IS12A R9 Step Down to near 2.5V 12 OC 73uS De-bounce H : 300mS L : 4.5uS 1MΩ PGO IS12B IS5 Iref X 8 Step Down to near 2.5V Iref X 8 Step Down to near 2.5V Iref X 8 12 OC 5 OC 3mS H : 20mS L : 4.5uS 3mS Power On Reset Internal Power POR = 4V 1.25V Constant Current Source Iref VCC Pext RI VCC IS33 Step Down to near 2.5V Iref X OC Band-Gap Reference 1.25V Clock Generator CLK GND -2-

4 Timing Chart Vcc FPO/ PGI VS12A IS12A VS12B IS12B VS5 IS5 VS33 IS33 Pext PGO T d1 T b1 T d3 T d2 AC turn on UVP/OVP/OCP Pext protect turn on turn off turn on AC turn off VPGI 1.25V 0.25V 1.13V T d1 T d2 OVP OVP/UVP/OCP/Pext OVP -3-

5 Pin Descriptions Pin No PIN NAME Descriptions 1 PGI Power good input signal pin 2 GND Ground 3 FPO/ Inverted fault protection output,open drain output stage 4 Remote ON/OFF control input pin 5 IS12A 12V(1) over current protection input pin 6 RI Current sense setting 7 IS12B 12V(2) over current protection input pin 8 VS12B 12V(2) over/under voltage protection input pin 9 Pext External protection detect input pin 10 IS5 5.0V over current protection input pin 11 IS33 3.3V over current protection input pin 12 VS12A 12V(1) over/under voltage protection input pin 13 VS33 3.3V over/under voltage protection input pin 14 VS5 5.0V over/under voltage protection input pin 15 VCC Power supply 16 PGO Power good output signal pin, open drain output stage Absolute Maximum Ratings Parameter Rating Unit Storage Temperature (Tstg) -40 to +125 C Operating Temperature (Topr) -30 to +90 C Supply Voltage (VCC) VCC -0.5 to V VS12A, VS12B, IS12A,IS12B -0.5 to V VS5, IS5-0.5 to +9.0 V Input Voltage Range (VI) VS33, IS to +7.0 V PGI -0.5 to V, Pext -0.5 to Vcc+0.5 V Output Voltage Range (VO) FPO/ -0.5 to Vcc+0.5 V PGO -0.5 to Vcc+0.5 V Output Current for RI (IRI) RI 12.5 to 62.5 ua, PGO > 5000 V ESD Susceptibility* (VESD) * Human Body Model (HBM). FPOB, VS12A, VS12B > 2000 V PGI, IS12A, IS12B, VCC > 3000 V Others > 4000 V -4-

6 Electrical Characteristics, Vcc=12V, T a = 25ºC. (unless otherwise specified) Power Supply Section Supply Voltage V Supply Current V = 5V ma Power On Reset Threshold Voltage (VPOR) V Power On Reset Hysteresis (VHYST) V Over-Voltage Section Over-Voltage Threshold VS V VS V VS12A/B V Under-Voltage Section Under-Voltage Threshold VS V VS V VS12A/B V Over-Current Section Offset Voltage VS33, VS mv VS12A/B mv Constant Current Generator Voltage (VRI) V PGI, Analog Input Threshold Voltage for start T d V Threshold Voltage for start T d V Threshold Voltage for mask OC,UV V Hysteresis (VHYST)* +/-20 +/-50 +/-80 mv * All of the comparator for PGI input in block diagram. -5-

7 Electrical Characteristics (Continued) PGO, Open Drain Digital Output Leakage Current (ILKG) VPGO=5V 5 ua Low Level Output Voltage (VOL) ISINK=10mA 0.3 V FPO/, Open Drain Digital Output Leakage Current (ILKG) VFPO/=5V 5 ua Low Level Output Voltage (VOL) ISINK=20mA 0.3 V, Analog Input Threshold Voltage ( High ) V Threshold Voltage ( Low ) V External Protection Detect Section Threshold(VTH) V Hysteresis (VHYST) +/-20 +/-50 +/-80 mv Switching Characteristics, Vcc=12V, T a = 25ºC. PGI to PGO Delay Time (Td1) ms Short Circuit Delay Time (Td2) PGI> 0.25V ms Short Circuit Delay Time (Td2-1) PGI< 0.25V ms PGO to FPO/ Delay Time (Td3) ms Under Voltage Delay Time (Td4) ms Over Current Delay Time (Td5) ms Over Voltage Delay Time (Td6) us Pext Delay Time (Td7) ms De-bounce Time (Tb1) ms PGO Noise De-glitch Time (Tb2) us -6-

8 Application Typical 4 rails SPS S.P.S. Secondary Side RS5 +5V Output +3.3V Coil RS V Output +12VACoil +12VBCoil RS12A RS12B +12VA Output +12VB Output VDET ROC5 ROC33 R OC12A R OC12B C PGI-1 RPGI-1 1 PGI PGO 16 RPGO 4.7K PGO +5V SB 1K 2 3 GND FPO/ Vcc VS VSB PSON IS12A RI VS33 13 VS12A 12 IS33 11 C33-1 C 5-1 C12B-1 7 IS12B IS5 10 CPS O N CPGI-2 RPGI-2 RI 8 VS12B PEXT C12A-1 9 Cby CPGO Pext C 12A-2 C 12B-2 Notes: 1. Zener diode or resistor or both of them can be used in component X. 2. The bypass capacitor C by suggests to be 0.1uF~ 10uF and layout nearby pin VCC. 3. The recommend sense values of R S12(1), R S12(2), R S5 and R S33 are 0.002Ω. 4. Over-Current Protection design example: VRI 1.25 (1) I ref = 20μA, RI = = = 62. 5K( Ω) I 20μ RI (2) R S5 =0.002 Ω, Δ V 5 V = I+ 5V = ROC5 8 Iref R OC5 = = 250 Ω 8 20μ (3) If +5V OCP trip point is 20A, ( ) -7-

9 Package Specification ( 16-pin DIP ) E 1 E e B θ D A Seating Plane A 1 L b 1 b e mm inch Symbol Dimension in mm Dimension in inch NOTE Min Normal Max Min Normal Max A A e B b b D E e E L θ 0º 7º 15º 0º 7º 15º -8-

10 The products listed herein are designed for ordinary electronic applications, such as electrical appliances, audio-visual equipment, communications devices and so on. Hence, it is advisable that the devices should not be used in medical instruments, surgical implants, aerospace machinery, nuclear power control systems, disaster/crime-prevention equipment and the like. Misusing those products may directly or indirectly endanger human life, or cause injury and property loss. Silicon Touch Technology, Inc. will not take any responsibilities regarding the misusage of the products mentioned above. Anyone who purchases any products described herein with the above-mentioned intention or with such misused applications should accept full responsibility and indemnify. Silicon Touch Technology, Inc. and its distributors and all their officers and employees shall defend jointly and severally against any and all claims and litigation and all damages, cost and expenses associated with such intention and manipulation. Silicon Touch Technology, Inc. reserve the right to make changes to their products or to discontinue any product or service without notice, and advise customers to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. -9-