FX-WRZRMT10K-0 Wireless Remote Temperature Transmitter

Transcription

1 FX-WRZRMT10K-0 Wireless Remote Temperature Transmitter Installation Instructions FX-WRZRMT10K-0, TE-6361A-1, TE-6361V-2, TE-636GV-2, TE-636S-1 Application The FX-WRZRMT10K-0 Wireless Remote Temperature Transmitter is designed to operate with a TE-6300 Series 10k ohm Johnson Controls Type II Thermistor Sensor (order separately) to sense the temperature in warmer applications up to 158 F (70 C), and transmit wireless temperature data to a receiver or controller. Ideal applications include data server racks, food warming ovens, warming baths, warm food storage units, and hospital neonatal incubators. In an FX-ZFR1800 Series Wireless Field Bus System (mesh network) application, the transmitter communicates with FX-PCG16 Series, FX-PCG26 Series, and FX-PCV16 Series Controllers by means of the FX-ZFR1811 Router. An FX-WRZRMT10K-0 Wireless Remote Temperature Transmitter can also be used in a One-to-One application (non-mesh network) to communicate with an FX-WRZ Wireless Receiver. The FX-WRZ Receiver transfers data to the controller by means of the Sensor Actuator (SA) Bus. In a typical application, one FX-WRZRMT10K-0 Transmitter reports to one FX-WRZ Receiver, but up to five FX-WRZRMT10K-0 Transmitters can be associated with a single FX-WRZ Receiver in averaging applications , Rev. E Part No , Rev. E Issued March 2016 Refer to the QuickLIT website for the most up-to-date version of this document. The FX-WRZRMT10K-0 Wireless Remote Temperature Transmitter can transmit sensed temperature and low battery conditions to an associated router or receiver. The FX-WRZRMT10K-0 Transmitter and associated TE-6300 Series Temperature Sensor are designed for indoor, intra-building applications only. IMPORTANT: The FX-WRZRMT10K-0 Wireless Remote Temperature Transmitter is intended to provide an input to equipment under normal operating conditions. Where failure or malfunction of the transmitter could lead to personal injury or property damage to the controlled equipment or other property, additional precautions must be designed into the control system. Incorporate and maintain other devices, such as supervisory or alarm systems or safety or limit controls, intended to warn of or protect against failure or malfunction of the transmitter. IMPORTANT : Le FX-WRZRMT10K-0 Wireless Remote Temperature Transmitter est destiné à transmettre des données entrantes à un équipement dans des conditions normales de fonctionnement. Lorsqu'une défaillance ou un dysfonctionnement du transmitter risque de provoquer des blessures ou d'endommager l'équipement contrôlé ou un autre équipement, la conception du système de contrôle doit intégrer des dispositifs de protection supplémentaires. Veiller dans ce cas à intégrer de façon permanente d'autres dispositifs, tels que des systèmes de supervision ou d'alarme, ou des dispositifs de sécurité ou de limitation, ayant une fonction d'avertissement ou de protection en cas de défaillance ou de dysfonctionnement du transmitter. FX-WRZRMT10K-0 Wireless Remote Temperature Transmitter Installation Instructions 1

2 North American Emissions Compliance United States Compliance Statement (Part 15.19) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. Warning (Part 15.21) Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment. Canada Industry Canada Statement The term IC before the certification/registration number only signifies that the Industry Canada technical specifications were met. Le terme «IC» précédant le numéro d'accréditation/ inscription signifie simplement que le produit est conforme aux spécifications techniques d'industry Canada. Installation Follow these guidelines when installing the FX-WRZRMT10K-0 Wireless Remote Temperature Transmitter and the associated TE-6300 Series Temperature Sensor: Transport the transmitter and sensor in their original containers to minimize vibration and shock damage. Verify that all the parts shipped with the transmitter and sensor. Do not drop the transmitter or sensor, or subject either component to physical shock. Do not attempt to remove or repair the circuit board from the transmitter housing. Other than battery replacement, the transmitter and sensor are not user serviceable. Parts Included FX-WRZRMT10K-0 Wireless Remote Temperature Transmitter (includes one transmitter, one mounting base, and strips of double-sided adhesive foam tape; all factory assembled) one strain relief bushing one DIP switch overlay for a mesh network application using an FX-ZFR1811 Router one DIP switch overlay for a non-mesh network, One-to-One application using an FX-WRZ Receiver one installation instructions sheet two AA alkaline batteries Dimensions See Figure 1 for dimensions and physical features of the FX-WRZRMT10K-0 Wireless Remote Temperature Transmitter and the associated TE-6300 Series Temperature Sensor. Signal Test Button F/ C Button Back of Base to Front of Protrusion 1/4 in. (6 mm) Outside Diameter 1-1/ / Tamper Resistant Set Screw 4-23/ Figure 1: FX-WRZRMT10K-0 and TE-6300 Dimensions and Physical Features, in./mm Special Tools Needed 1/16 in. (1.6 mm) Allen-head adjustment tool (Johnson Controls T ; order separately) for the tamper-resistant set screw that secures the transmitter to the mounting base 1/8 in. (3 mm) blade screwdriver for making wiring connections to the terminal block on the transmitter FIG:dmnsns 10 ft (3 m) Plenum-Rated Cable 2 FX-WRZRMT10K-0 Wireless Remote Temperature Transmitter Installation Instructions

3 coin for unlocking the transmitter housing from the mounting base locking tab Mounting The FX-WRZRMT10K-0 Wireless Remote Temperature Transmitter can be surface mounted using the adhesive tape pieces affixed to the back of the transmitter. The transmitter can also be mounted on metal surfaces using a Johnson Controls MAGNET-BASE-PLW Magnetic Backplate (order separately). To mount the TE-6300 Series Temperature Sensor, refer to the installation instructions included with the device. Note: If another manufacturer s 10k ohm thermistor sensor is used with the FX-WRZRMT10K-0 Wireless Remote Temperature Transmitter, the sensor must be mounted within 10 ft (3 m) of the transmitter. Location Considerations When locating the temperature transmitter: Mount the transmitter vertically, for ease of reading the Liquid Crystal Display (LCD) on the face of the unit. Locate the transmitter on the same building level as the nearest FX-ZFR1811 Router or FX-WRZ Receiver. For best signal transmission, locate the transmitter at least 2 in. (51 mm) away from any metal obstructions. Wherever possible, locate the transmitter in the direct line of sight to the FX-ZFR1811 Router or FX-WRZ Receiver. Signal transmission is best if the path between the transmitter and the router or receiver is as direct as possible. Line of sight is desirable but not required, as long as the path is not blocked by large metal objects. Avoid metal obstructions (including equipment rooms and elevator shafts) and concrete or brick walls between the transmitter and the FX-ZFR1811 Router or FX-WRZ Receiver. Do not mount the transmitter closer than 2 ft (0.61 m) or farther than 100 ft (30 m) from the FX-ZFR1811 Router, or 150 ft (45 m) from the FX-WRZ Receiver. The recommended indoor line-of-sight transmission range between the transmitter and the FX-ZFR1811 Router is 50 ft (15 m). Run the temperature sensor wire lead to the transmitter, supporting the wire lead along the way as necessary. This wire lead should not exceed 10 ft (3 m) in length. Installing the FX-WRZRMT10K-0 Wireless Remote Temperature Transmitter The FX-WRZRMT10K-0 Wireless Remote Temperature Transmitter can be surface mounted using the double-sided adhesive foam tape factory-installed on the back of the device. To mount the transmitter base with adhesive foam tape: 1. Clean the desired mounting surface to ensure that the adhesive foam tape sticks to the surface. Note: The mounting surface, mounting base, and ambient temperature must be at least 50 F (10 C) when mounting the transmitter base with adhesive foam tape. 2. Remove the transmitter housing from its mounting base (Figure 2). 2. Insert a coin into the slot on the top of the transmitter housing, and depress the locking tab on the mounting base to release the housing. Transmitter Housing 3. Swing the transmitter housing off the mounting base. 1. Loosen (but do not remove) the tamper-resistant set screw on the locking tab of the mounting base. Mounting Base Tabs 4. Pull the bottom of the transmitter housing down and off the tabs on the mounting base. FIG:trnsmttr_rmvl Figure 2: Removing the Transmitter Housing from its Mounting Base (Reverse the Steps to Reinstall the Housing) FX-WRZRMT10K-0 Wireless Remote Temperature Transmitter Installation Instructions 3

4 3. Peel off the protective paper from one side of the factory-installed strips of adhesive foam tape on the back of the mounting base. 4. When positioned correctly, the arrow between the terminal slots on the inside of the mounting base should point up. Ensure that the mounting base is upright (tamper-resistant set screw on top) and press the base firmly onto the clean mounting surface. 5. See Connecting the TE-6300 Series Temperature Sensor to the FX-WRZRMT10K-0 Wireless Remote Temperature Transmitter. Removing a Mounting Base Installed with Double-Sided Adhesive Foam Tape To remove or relocate a transmitter mounted with double-sided adhesive foam tape: 1. Remove the transmitter housing from its mounting base (Figure 2). 2. Remove the mounting base from the mounting surface by carefully twisting the base off of the surface. 3. Remove the adhesive foam tape from the mounting base and clean the mounting base to remove any leftover adhesive. Note: New double-sided adhesive foam tape is required to remount the base on the surface; use Can-Do National Tape (Code No ) adhesive foam tape or its equivalent. Connecting the TE-6300 Series Temperature Sensor to the FX-WRZRMT10K-0 Wireless Remote Temperature Transmitter To connect the TE-6300 Series Temperature Sensor to the FX-WRZRMT10K-0 Wireless Remote Temperature Transmitter: 1. Feed the wire lead through the hole on the bottom edge of the transmitter housing. 2. Loop the wire lead through the strain relief bushing (included with the transmitter) as shown in Figure 3, just inside the bottom edge of the transmitter housing. Note: The strain relief bushing is designed to accommodate wire sizes ranging from 1/16 to 3/16 in. (2 to 5 mm) in diameter FIG:strn_rlf_bshng Figure 3: Looping the Wire Lead through the Strain Relief Bushing 4 FX-WRZRMT10K-0 Wireless Remote Temperature Transmitter Installation Instructions

5 3. Remove the terminal block from the circuit board. 4. Secure the wire ends to the terminal block using a 1/8 in. (3 mm) blade screwdriver. The recommended torque is 3 lb ft (4 N m). Note: The wiring connections on the terminal block are interchangeable. 5. Reinstall the terminal block onto the circuit board as illustrated in Figure 4. IMPORTANT: Do not power up the FX-WRZRMT10K-0 Wireless Remote Temperature Transmitter until a receiver or controller is installed and operating within the same Radio Frequency (RF) range. If this condition is not met, the transmitter uses a higher-than-normal battery current as it attempts to find a receiver or controller within range, resulting in reduced battery life. Preparing the FX-WRZRMT10K-0 Wireless Remote Temperature Transmitter for Operation To prepare the FX-WRZRMT10K-0 Wireless Remote Temperature Transmitter for operation, and to reinstall the transmitter housing on its mounting base: 1. Place the appropriate DIP switch overlay (based on the application) over the DIP switches. See Figure 5 through Figure 7. FIG:zfr1811_msh Figure 5: Mesh Network Application DIP Switch Overlay FIG:wrz78xx_non_msh FIG:prb_wrng Figure 6: Non-mesh Network, One-to-One Application DIP Switch Overlay Figure 4: Connecting the TE-6300 Series Temperature Sensor to the FX-WRZRMT10K-0 Wireless Remote Temperature Transmitter FX-WRZRMT10K-0 Wireless Remote Temperature Transmitter Installation Instructions 5

6 Table 1: Setting the ZONE DIP Switches Zone Number SA Bus Address Place DIP switch overlay here. Insert two AA alkaline batteries in battery compartment. AA Alkaline Battery AA Alkaline Battery FIG:bck_wrz_str0000_0 Figure 7: Back of FX-WRZRMT10K-0 Wireless Remote Temperature Transmitter Showing DIP Switches and Batteries 2. Set the DIP switches located on the back of the transmitter. For a mesh network application using an FX-ZFR1811 Router (Figure 5), set the DIP switches as indicated. Refer to the FX-ZFR Series Wireless Field Bus System Technical Bulletin (LIT ) for information on commissioning multiple FX-WRZRMT10K-0 Wireless Remote Temperature Transmitters in an FX-ZFR1800 Series Wireless Field Bus System. a. Set the POWER switch to OFF. b. Set the MODE switch to Mesh. c. Set the PAN OFFSET switches according to the job or system plans. IMPORTANT: Ensure that the PAN OFFSET is the same for each FX-ZFR1810 Coordinator, FX-FR1811 Router, and FX-WRZRMT10K-0 Wireless Remote Temperature Transmitter in a mesh network. d. Set the ZONE DIP switches to match the Zone Number in the Facility Explorer Programmable Controller Tool (FX-PCT) software. Each Zone Number corresponds to the SA Bus Address as shown in Table 1. e. Set the MSTP ADDRESS DIP switches to match the Master-Slave/Token-Passing (MS/TP) address of the controller with which the transmitter is intended to communicate. f. Set the TRANSMIT LEVEL switch to 10mW. For a non-mesh network, One-to-One application using an FX-WRZ Receiver (Figure 6), set the DIP switches as indicated, ensuring that the AREA and TRANSMITTER ID switches on the FX-WRZ Receiver and the FX-WRZRMT10K-0 Wireless Remote Temperature Transmitter(s) are set to the same value. a. Set the POWER switch to OFF. b. Set the MODE switch to 1 to 1. c. Set the SENSOR # to 199 for applications with only one transmitter per controller. Use the other settings for additional transmitters in applications with a single controller. Refer to the One-to-One Wireless Sensing System Technical Bulletin (LIT ) for information on commissioning multiple FX-WRZRMT10K-0 Wireless Remote Temperature Transmitters in an FX-WRZ One-to-One Wireless Room Temperature Sensing System. d. Set the AREA switches to match the AREA switch on the FX-WRZ Receiver. e. Set the TRANSMITTER ID switches to match the TRANSMITTER ID on the FX-WRZ Receiver. 3. Install two AA alkaline batteries (supplied) into the battery compartment on the back of the transmitter. Ensure that the batteries are installed in the proper polarity (Figure 7). 6 FX-WRZRMT10K-0 Wireless Remote Temperature Transmitter Installation Instructions

7 4. If the address DIP switches are set to the correct positions and the temperature sensing system is ready for operation or testing, set the POWER DIP switch to the ON position (Figure 5 or Figure 6). 5. Align the tabs on the bottom edge of the transmitter mounting base with the slots on the bottom edge of the transmitter housing, and rotate the transmitter assembly onto its mounting base. (Reverse the procedure shown in Figure 2.) 6. Use a 1/16 in. (1.6 mm) Allen wrench or Johnson Controls T Allen-Head Adjustment Tool to tighten the tamper-resistant set screw and secure the transmitter assembly onto its mounting base (Figure 2). Press and release the signal test button on the FX-WRZRMT10K-0 Wireless Remote Temperature Transmitter (Figure 1) to initiate a signal strength test with the associated FX-ZFR1811 Router or FX-WRZ Receiver. The signal strength is shown on the LCD on the face of the transmitter (Figure 8). F Signal Strength Graph: = No Signal = Weak or Marginal Signal = Adequate Signal = Excellent Signal Digital Readout for 104 F Note: Digital readouts above 99.9 F are whole numbers (no decimals), where the first and second digits are full size and the third digit is half size. Digital readouts for Celsius temperatures are normal size and include decimals. Indicates Loss of Network Connection When Symbol Flashes On Figure 8: FX-WRZRMT10K-0 Wireless Remote Temperature Transmitter LCD An optional FX-WRZSST-110 Wireless Sensing System Tool can also be used with the FX-WRZRMT10K-0 Wireless Remote Temperature Transmitter prior to installation as a site survey tool, to determine potential installation locations for system devices and to determine the wireless signal strength between the system devices in the application. FIG:lcd_dsply Refer to the FX-WRZSST-110 Wireless Sensing System Tool Installation Instructions (Part No ) for more information on testing signal strength. Additional Product Information Table 2 includes Negative Temperature Coefficient (NTC) thermistor sensor temperature/resistance response characteristics for the TE-6300 Series Temperature Sensor. The values included in this table can be used to verify the accuracy of the temperature sensor in the field. Note: If another manufacturer s 10k ohm thermistor sensor is used with the FX-WRZRMT10K-0 Wireless Remote Temperature Transmitter, the values for the temperature/resistance response characteristics may be different than those indicated in Table 2 for the Johnson Controls TE-6300 Series Temperature Sensor. This difference may cause the transmitter to read temperatures incorrectly. Table 2: Temperature vs. Resistance Temperature, F ( C) Resistance, ohms -50 (-46) 489, (-40) 366, (-34) 233, (-29) 165, (-23) 117,978 0 (-18) 85, (-12) 62, (-7) 46, (-1) 34, (4) 26, (10) 19, (16) 15, (21) 11, (27) 9, (32) 7, (38) 5, (43) 4, (49) 3, (54) 3, (60) 2, (66) 2, (71) 1, (77) 1,401 FX-WRZRMT10K-0 Wireless Remote Temperature Transmitter Installation Instructions 7

8 Setup and Adjustments The FX-WRZRMT10K-0 Wireless Remote Temperature Transmitter and TE-6300 Series Temperature Sensor combination is configured as a NetZoneSensor (also identified as Zone NetSensor) in the FX-PCT software. The following steps describe how to define the hardware setting, as well as how to adjust the default temperature limits. This adjustment allows the FX-WRZRMT10K-0 Wireless Remote Temperature Transmitter to properly report the temperature to the controller. To define the hardware setting in FX-PCT: 1. Click Define Hardware. The Hardware Definition Wizard opens with the Controller Selection screen active. Note: You can also use the Define Hardware option of the Operations menu to open the Hardware Definition Wizard. 2. Click Select next to the Field Device box. The Controller Device Selection dialog box appears. 3. Select the desired field device and click OK. The Add Device dialog box appears. 4. Enter the device name and click OK. The device name appears in the Field Device box. 5. In the SA Bus Devices box of the Controller Selection screen, verify that the Zone NetSensor option appears. The Zone NetSensor option applies to the FX-WRZRMT10K-0. If this option appears, skip to Step 9. If this option does not appear, continue with Step Click Add Device next to the SA Bus Devices box. The SA Bus Device Selection dialog box appears. 7. Select the NetZoneSensor option and click OK. The Add NetSensor Devices dialog box appears. 8. Select the check box next to the application (Zone) and click OK. The Hardware Definition Wizard - Controller Selection screen re-appears with the Zone NetSensor device in the SA Bus Devices box. 9. Click Next. The Hardware Definition Wizard - Point Assignment screen appears. Note: FX-PCT automatically assigns the points based on the selections made in the Controller Selection screen. The Zone temperature input point does not appear on the Point Assignment screen because this point is assigned to the SA Bus. 10. Assign your points if needed. Use the right arrow to assign a point to an object. Use the left arrow to unassign a point from an object. Use drag-and-drop functionality to move a point up and down the Assigned Points list. 11. Click Next. The Network Settings screen appears. 12. Review and modify the settings, if needed. Note: The default address of the Zone NetSensor is 199 (appears in the SA Bus Device Settings section of the screen). Be aware that this address is not the same as the Device Address (appears in the Field Device & Bus Settings section of the screen). 13. Click Finish. The hardware settings for the FX-WRZRMT10K-0 Wireless Remote Temperature Transmitter and TE-6300 Series Temperature Sensor combination are defined. To adjust the default temperature limits in FX-PCT: Note: The FX-WRZRMT10K-0 Wireless Remote Temperature Transmitter and TE-6300 Series Temperature Sensor combination uses the Zone (ZN-T) temperature input point. All other points associated with temperature (for example, setpoint, occupancy mode, and fan status) are not applicable to the FX-WRZRMT10K-0 Wireless Remote Temperature Transmitter and TE-6300 Series Temperature Sensor combination. The Min Value on an engine must be set to greater than or equal to -9 F (-23 C) to prevent unreliable status indicators. 1. With the Control tab active, right-click the ZN-T input and select View Details. The Details dialog box appears. 2. Click Edit. 3. Change the Max Value setting to deg F (70 deg C) and verify that the Min Value setting is 32.0 deg F (0 deg C). 4. Click Apply. 5. Click Close. The default temperature limits are adjusted. 6. Save the application (File > Save), and download the application to the device (Operations > Load). For more information on how to use FX-PCT, refer to the User Interface and Defining Hardware chapters of the Controller Tool Help (LIT ). 8 FX-WRZRMT10K-0 Wireless Remote Temperature Transmitter Installation Instructions

9 Repair Information If the FX-WRZRMT10K-0 Wireless Remote Temperature Transmitter fails to operate within its specifications, replace the unit. For a replacement transmitter, contact the nearest Johnson Controls representative. The two AA alkaline batteries supplied with the FX-WRZRMT10K-0 Wireless Remote Temperature Transmitter typically have a life of 5 years or more. The transmitter reports a low battery condition to the receiver or controller, which relays the low battery condition to the Facility Explorer system. The low battery condition is also shown on the LCD on the face of the transmitter. Technical Specifications Replace the transmitter batteries with two high-quality AA alkaline batteries as necessary, ensuring that the batteries are installed in the proper polarity (Figure 7). Note: When replacing batteries, both batteries should be replaced at the same time. Batteries removed from this device must be recycled or disposed of in accordance with local, national, and regional regulations. Only certified technicians or qualified building maintenance personnel should service Johnson Controls products. Lithium batteries with a maximum cell voltage of 1.5 volts can be substituted to extend the period between replacing the batteries. Do not mix lithium and alkaline batteries in this device. Table 3: Accessories Ordering Information Code Number Description TE-6361A-1 Johnson Controls 10k ohm Type II Thermistor Sensor; 8 in. (203 mm) Duct Probe, Adjustable Enclosure TE-6361V-2 Johnson Controls 10k ohm Type II Thermistor Sensor; 8 in. (203 mm) Duct Probe, Flange Mount Enclosure TE-636GV-2 Johnson Controls 10k ohm Type II Thermistor Sensor; 4 in. (102 mm) Duct Probe, Flange Mount Enclosure TE-636S-1 Johnson Controls 10k ohm Type II Thermistor Sensor; Strap-Mount Probe FX-WRZSST-110 Wireless Sensing System Tool: For Use with an FX-WRZRMT10K-0 Wireless Remote Temperature Transmitter, to Function as a Site Survey Tool for the FX-WRZ Series One-to-One Wireless Room Sensing System, or for the FX-ZFR1800 Wireless Field Bus System MAGNET-BASE-PLW Magnetic Backplate for Mounting the Transmitter on Metal Surfaces; 5 Magnetic Backplates per Package T Allen-Head Adjustment Tool: 1/16 in. (1.6 mm), for the Tamper-Resistant Set Screw That Secures the Temperature Transmitter to the Mounting Base; 30 Tools per Package FX-WRZRMT10K-0 Wireless Remote Temperature Transmitter (Part 1 of 2) Power Requirements 3 VDC Supplied by Two 1.5 VDC AA Alkaline Batteries (Included with Transmitter); Typical Battery Life: 5 Years or More; 7 Years Using Lithium Batteries Addressing DIP Switches, Field Adjustable; MS/TP Address, Network Number, and Zone Address Transmitter Ambient Conditions RF Band Transmission Power Transmission Range Transmissions Operating: 23 to 111 F (-5 to 44 C), 5 to 95% RH, Noncondensing Storage: -4 to 140 F (-20 to 60 C), 5 to 95% RH, Noncondensing Direct-Sequence, Spread-Spectrum; 2.4 GHz ISM Band 10 mw Maximum Mesh Network Application: 100 ft (30 m) Maximum Indoor Line of Sight; 50 ft (15 m) Practical Average Indoor Non-mesh Network, One-to-One Application: 150 ft (45 m) Maximum Indoor Line of Sight; 100 ft (30 m) Practical Average Indoor Every 120 Seconds (±20 Seconds) FX-WRZRMT10K-0 Wireless Remote Temperature Transmitter Installation Instructions 9

10 FX-WRZRMT10K-0 Wireless Remote Temperature Transmitter (Part 2 of 2) Temperature System Accuracy Materials Mounting Compliance Shipping Weight ±1.8F /±1.0C Over the Range of 32 to 158 F (0 to 70 C) NEMA 1 White Plastic Housing Surface Mounted Using Factory-Installed, Double-Sided Adhesive Foam Tape United States: Transmission Complies with FCC Part Regulations for Low Power Unlicensed Transmitters; Transmitter FCC Identification: TFB-MATRIXL or OEJ-WRZRADIO Canada: Industry Canada IC: 5969A-MATRIXL or 279A-WRZRADIO Europe: CE Mark Johnson Controls, Inc., declares that this product is in compliance with the essential requirements and other relevant provisions of the R&TTE Directive lb (0.25 kg) TE-6300 Series Temperature Sensors Sensor Type Sensor Thermal Characteristics Sensor Temperature Coefficient Electrical Connections Probe Materials Mounting Operating Temperature Limits Shipping Weight 10k ohm Johnson Controls Type II Thermistor Sensor See Table 2 Nonlinear 10k ohm NTC Thermistor 22 AWG (0.6 mm Diameter) x 10 ft (3 m) Long Plenum-Rated Cable (White Leads) Stainless Steel Mount within 10 ft (3 m) of the FX-WRZRMT10K-0 Wireless Remote Temperature Transmitter Cable: -50 to 140 F (-46 to 60 C) Probe: -50 to 220 F (-46 to 104 C) 0.2 lb (0.09 kg) The performance specifications are nominal and conform to acceptable industry standard. For application at conditions beyond these specifications, consult the local Johnson Controls office. Johnson Controls, Inc. shall not be liable for damages resulting from misapplication or misuse of its products. European Single Point of Contact: NA/SA Single Point of Contact: APAC Single Point of Contact: JOHNSON CONTROLS WESTENDHOF ESSEN GERMANY JOHNSON CONTROLS 507 E MICHIGAN ST MILWAUKEE WI USA JOHNSON CONTROLS C/O CONTROLS PRODUCT MANAGEMENT NO. 22 BLOCK D NEW DISTRICT WUXI JIANGSU PROVINCE CHINA Building Efficiency 507 E. Michigan Street, Milwaukee, WI Johnson Controls is a registered trademark of Johnson Controls, Inc. All other marks herein are the marks of their respective owners Johnson Controls, Inc. 10 FX-WRZRMT10K-0 Wireless Remote Temperature Transmitter Installation Instructions Published in U.S.A.