Obsolete Product(s) - Obsolete Product(s)
|
|
|
- Loreen Potter
- 6 years ago
- Views:
Transcription
1 High speed differential line drivers Features Meets or exceeds the requirements of ANSI TIA/EIA-644 standard Low voltage differential signaling with typical output voltage of 350 mv and a 100 Ω load Typical output voltage rise and fall times of 750 ps (400 Mbps) Typical propagation delay times of 1.7 ns Operates from a single 3.3 V supply Power dissipation 25 mw typical per driver at 200 MHz Driver at high impedance when disabled or with V CC = 0 V Pin compatible with the AM26LS31, SN65LVDS31 Low voltage TTL (LVTTL) logic input levels Description The STLVDS31B is a quad differential line drivers that implements the electrical characteristics of low voltage differential signaling (LVDS). This signaling technique lowers the output voltage levels of 5 V differential standard levels (such as TIA/EIA-422B) to reduce the power, increase the switching speeds and allows operations with a 3.3 V supply rail. Any of the four current mode drivers will deliver a minimum differential output voltage magnitude of 247 mv into a 100 Ω load when enabled. The intended application of this device and signalling technique is for point-to-point baseband data transmission over controlled impedancemedia approximately 100 Ω. The TSSOP16 transmission media may be printed circuit board traces, backplanes or cables. The ultimate rate and distance of data transfer is dependent upon the attenuation characteristics of the media and noise coupling to the environment. The STLVDS31B is characterized for operation from - 55 C to 125 C. Table 1. Device summary Order code Temperature range Package Packaging STLVDS31BTR - 40 to 85 C TSSOP16 (tape and reel) 2500 parts per reel July 2009 Doc ID 8338 Rev 6 1/
2 Contents STLVDS31B Contents 1 Pin configuration Maximum ratings Electrical characteristics Typical characteristics Typical performance characteristics Package mechanical data Revision history /15 Doc ID 8338 Rev 6
3 Pin configuration 1 Pin configuration Figure 1. Pin connections and functional diagram Table 2. Pin description Pin n Symbol Name and function 1, 7, 9, 15 1A to 4A Driver inputs 2, 6, 10, 14 1Y to 4Y Driver outputs 3, 5, 11, 13 1Z to 4Z Driver outputs 4 G Enable 12 G Enable 8 GND Ground 16 V CC Supply voltage Doc ID 8338 Rev 6 3/15
4 Pin configuration STLVDS31B Figure 2. Logic diagram and logic symbol Table 3. Table 4. Truth table for receiver Truth table V ID = V A - V B V ID 100 mv mv < V ID < 100 mv? V ID 100 mv OPEN Input Enables Outputs A G G Y Z H H X H L L H X L H H X L H L L X L L H X L H Z Z OPEN H X L H OPEN X L L H R H L H L = Low level, H = High Level, X = Don t care, Z = High Impedance 4/15 Doc ID 8338 Rev 6
5 Maximum ratings 2 Maximum ratings Table 5. Note: Absolute maximum ratings Symbol Parameter Value Unit V CC Supply voltage (1) 1. All voltages except differential I/O bus voltage, are with respect to the network ground terminal. Table to 4.6 V V I DC input voltage -0.5 to (V CC + 0.5) V T STG Storage temperature range -65 to +150 C Absolute maximum ratings are those values beyond which damage to the device may occur. Functional operation under these condition is not implied. Recommended operating conditions Symbol Parameter Min. Typ. Max. Unit V CC Supply voltage V V IH HIGH level input voltage 2.0 V V ILI LOW level input voltage 0.8 V T A Operating temperature range C Doc ID 8338 Rev 6 5/15
6 Electrical characteristics STLVDS31B 3 Electrical characteristics Table 7. Over recommended operating conditions unless otherwise noted. All typical values are at T A = 25 C, and V CC = 3.3 V. Electrical characteristics Symbol Parameter Test condition Min. Typ. Max. Unit V OD ΔV OD ΔV OC(SS) V OC(SS) V OC(PP) I CC Differential output voltage Change in differential output voltage between logic state Change in steady-state common mode output voltage between logic state Steady-state common mode output voltage Peak to peak common mode output voltage Supply current R L = 100Ω, Figure mv mv Figure V Figure mv mv V IN = 0.8V or 2V, Enabled, No Load ma V IN = 0.8V or 2V, Enabled, R L = 100Ω ma V IN = 0 or V CC, Disabled ma I IH High level input current V IH = 2V 4 20 µa I IL Low level input current V IL = 0.8V µa I SC Short circuit output current V O(Y) or V O(Z) = 0V ma V OD = 0 ± 12 ma I OZ High impedance output current V O = 0 or 2.4V ± 1 µa I CS Cold spare leakage current V I = 3.6V, V DD = 0V ± 20 µa I OFF Power OFF output current V CC = 0, V O = 2.4V ± 1 µa C IN Input capacitance 3 pf 6/15 Doc ID 8338 Rev 6
7 Electrical characteristics Over recommended operating conditions unless otherwise noted. All typical values are at T A = 25 C, and V CC = 3.3 V. Table 8. Switching characteristics (1) Symbol Parameter Test condition Min. Typ. Max. Unit t PLH Propagation delay time, low to high output ns t PHL Propagation delay time, high to low output ns t r Differential output signal rise time R L = 100Ω, C L = 10pF Figure ns t f Differential output signal fall time ns t sk(p) Pulse skew ( t THL = t TLH ) ns t sk(o) Channel to channel output skew (2) ns t PZH Propagation delay time, high impedance to high level output ns t PZL t PHZ t PLZ Propagation delay time, high impedance to low level output Propagation delay time, high level to high impedance output Propagation delay time, low level to high impedance output Figure 4 1. RS-232 IN to TTL-CMOS OUT (from 50 % to 50 %). 2. t sk(o) is the maximum delay time difference between drivers on the same device ns ns ns Doc ID 8338 Rev 6 7/15
8 Typical characteristics STLVDS31B 4 Typical characteristics Figure 3. Voltage and current definitions Figure 4. Figure 5. Test circuit, timing and voltage definitions for differential output signal 1. All input pulse are supplied by a generator having the following characteristics: t r or t f 1 ns, pulse repetition rate (PRR) = 50 Mpps, pulse width = 10 ± 0.2 ns. 2. C L includes instrumentation and fixture capacitance within 6 mm. of the D.U.T. Test circuit and definitions for the driver common mode output voltage 1. All input pulse are supplied by a generator having the following characteristics: t r or t f 1 ns, pulse repetition rate (PRR) = 50 Mpps, pulse width = 10 ± 0.2 ns. 2. C L includes instrumentation and fixture capacitance within 6mm of the D.U.T 3. The measurement of V OC(PP) is made on test equipment with a -3 db bandwidth of at least 300 MHz. 8/15 Doc ID 8338 Rev 6
9 Typical characteristics Figure 6. Enable and disable time test circuit and waveform 1. All input pulse are supplied by a generator having the following characteristics: t r or t f 1 ns, pulse repetition rate (PRR) = 0.5 Mpps, pulse width = 500 ± 10 ms. 2. C L includes instrumentation and fixture capacitance within 6 mm. of the D.U.T. Doc ID 8338 Rev 6 9/15
10 Typical performance characteristics STLVDS31B 5 Typical performance characteristics Unless otherwise specified T J = 25 C Figure 7. Supply current vs. temperature Figure 8. Supply current vs. temperature Figure 9. Propagation delay enable to output Figure 10. Propagation delay time Figure 11. Differential output signal 10/15 Doc ID 8338 Rev 6
11 Package mechanical data 6 Package mechanical data In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK packages, depending on their level of environmental compliance. ECOPACK specifications, grade definitions and product status are available at: ECOPACK is an ST trademark. Doc ID 8338 Rev 6 11/15
12 Package mechanical data STLVDS31B TSSOP16 mechanical data Dim. mm. inch. Min. Typ. Max. Min. Typ. Max. A A A b c D E E e 0.65 BSC BSC K L A A2 A1 b e K L c E D E1 PIN 1 IDENTIFICATION D 12/15 Doc ID 8338 Rev 6
13 Package mechanical data Tape & reel TSSOP16 mechanical data Dim. mm. inch. Min. Typ. Max. Min. Typ. Max. A C D N T Ao Bo Ko Po P Doc ID 8338 Rev 6 13/15
14 Revision history STLVDS31B 7 Revision history Table 9. Document revision history Date Revision Changes 28-Mar Order codes updated. 15-Jul Modified: Features on page 1. 14/15 Doc ID 8338 Rev 6
15 Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries ( ST ) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan - Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America Doc ID 8338 Rev 6 15/15
Obsolete Product(s) - Obsolete Product(s)
High speed differential line receivers Features Meets or exceeds the requirements of ansi TIA/EIA-644 standard Operates with a single 3.3 V supply Designed for signaling rate up to 400 Mbps Differential
Obsolete Product(s) - Obsolete Product(s)
High speed differential line drivers and receivers Feature summary Meets or exceed the requirements of ansi eia/tia-644-1995 standard Signaling rates up to 400Mbit/s Bus terminal ESD exceeds 6kV Operates
Order codes Temperature range Package Packaging
CMOS quad 3-state differential line driver Features TTL input compatible Typical propagation delay: 6 ns Typical output skew: 0.5 ns Output will not load line when V CC = 0 V Meets the requirements of
Order codes Temperature range Package Packaging
CMOS quad 3-state differential line receiver Features CMOS design for low power ± 0.2 V sensitivity over input common mode voltage range Typical propagation delay: 19 ns Typical input hysteresis: 60 mv
ST485AB. Very high speed low power RS-485/RS-422 transceiver. Features. Description
Very high speed low power RS-485/RS-422 transceiver Features Low supply current: 5 ma max High data rate > 30 Mbps Designed for RS 485 interface applications -7 to 12 common mode input voltage range Driver
Order code Temperature range Package Packaging
Low power high speed RS-485/RS-422 transceiver Features Low supply current: 5 ma max -7 V to 12 V common mode input voltage range 70 mv typical input hysteresis Designed for 25 Mbps operation Operate from
Obsolete Product(s) - Obsolete Product(s)
High bandwidth analog switch with 16-to-8 bit MUX/DEMUX Features Low R ON : 5.5 Ω typical V CC operating range: 3.0 to 3.6 V Low current consumption: 20 µa ESD HBM model: > 2 kv Channel on capacitance:
Order code Temperature range Package Packaging
ST485ERB ±15 kv ESD protected, low power RS-485/RS-422 transceiver Features Low quiescent current: 300 µa Designed for RS-485 interface application - 7 V to 12 V common mode input voltage range Driver
Part number Temperature range Package Packaging
Low power RS-485/RS-422 transceiver General features Low quiescent current: 300µA Designed for RS-485 interface application -7V to 12V common mode input voltage range Driver maintains high impedance in
Description. Order code Temperature range Package Packaging Marking
Low-voltage CMOS quad bus buffer (3-state) with 5 V tolerant inputs and outputs Datasheet production data Features 5 V tolerant inputs and outputs High speed t PD = 5.2 ns (max.) at V CC = 3 V Power-down
Order code Temperature range Package Packaging
ST75C176B ST75C176C Low power RS-485/RS-422 transceiver Features Low quiescent current: 300 ma Designed for RS-485 interface applications -7 V to 12 V common mode input voltage range Driver maintains high
Part number Temperature range Package Packaging
ST1480AB ST1480AC 3.3 V powered, 15 kv ESD protected, up to 12 Mbps true RS-485/RS-422 transceiver Features ESD protection ±15 kv human body model ±8 kv IEC 1000-4-2 contact discharge Operate from a single
Obsolete Product(s) - Obsolete Product(s)
Single bilateral switch Features High speed: t PD = 0.3 ns (typ.) at V CC = 5 V t PD = 0.4 ns (typ.) at V CC = 3.3 V Low power dissipation: I CC = 1 μa (max.) at T A =25 C Low "ON" resistance: R ON =6.5Ω
Obsolete Product(s) - Obsolete Product(s)
Low voltage CMOS octal bus buffer (3-state) with 5V tolerant inputs and outputs Features 5V tolerant inputs and outputs High speed: t PD = 8.0ns (Max) at V CC = 3V Power down protection on inputs and outputs
74LCX139 Low voltage CMOS Dual 2 to 4 decoder / demultiplexer Features Description Order codes
Low voltage CMOS Dual 2 to 4 decoder / demultiplexer Features 5V tolerant inputs High speed: t PD = 6.2ns (Max) at V CC = 3V Power down protection on inputs and outputs Symmetrical output impedance: I
KF25B, KF33B KF50B, KF80B
KF25B, KF33B KF50B, KF80B Very low drop voltage regulators with inhibit Datasheet production data Features Very low dropout voltage (0.4 V) Very low quiescent current (typ. 50 µa in OFF mode, 500 µa in
Obsolete Product(s) - Obsolete Product(s)
High bandwidth switch with 20- to 10-bit MUX/DEMUX Datasheet - production data Features Low R ON : 4.0 Ω typical V CC operating range: 3.0 to 3.6 V Enhanced ESD protection: > 8 kv (contact) and 15 kv (HBM)
HCF4093. QUAD 2-input NAND Schmidt trigger. Features. Description
QUAD 2-input NAND Schmidt trigger Features Schmidt trigger action on each input with no external components Hysteresis voltage typically 0.9 V at V DD =5V and 2.3 V at V DD =10 V Noise immunity greater
Obsolete Product(s) - Obsolete Product(s)
Low power single inverter gate Features High speed: t PD = 4.3 ns (max.) at V CC = 2.3 V Power down protection on inputs and outputs Balanced propagation delays: t PLH t PHL Operating voltage range: V
Description. Table 1. Device summary. Order code Temp. range Package Packaging Marking
Quad bus buffer (3-state) Datasheet - production data Features SO14 TSSOP14 High-speed: t PD = 8 ns (typ.) at V CC = 6 V Low power dissipation: I CC = 4 μa (max.) at T A = 25 C High noise immunity: V NIH
Single 8-channel analog MUX/DEMUX with injection current protection. Description. Order code Temperature range Package Packaging Marking
Features Single 8-channel analog MUX/DEMUX with injection current protection Datasheet production data Low power dissipation I CC = 2 μa (max.) at T A = 25 C Injection current protection V ΔOUT < 1 mv
Obsolete Product(s) - Obsolete Product(s)
RS-232 quad line driver General features Current limited output ±10mA typ. Power-off source impedance 300Ω min. Simple slew rate control with external capacitor Flexible operating supply range Inputs are
Description. Table 1. Device summary. Order code Temp. range Package Packing Marking
Hex bus buffer with 3-state outputs (non-inverting) Datasheet - production data Features SO16 TSSOP16 High-speed: t PD = 10 ns (typ.) at V CC = 6 V Low power dissipation: I CC = 4 μa (max.) at T A = 25
Order code Temperature range Package Packaging Marking
Micropower quad CMOS voltage comparator Datasheet production data Features Extremely low supply current: 9 μa typ./comp. Wide single supply range 2.7 V to 16 V or dual supplies (±1.35 V to ±8 V) Extremely
Obsolete Product(s) - Obsolete Product(s)
Single buffer/driver with open drain Features 5 V tolerant inputs High speed: t PD = 4.2 ns (max.) at V CC = 3.3 V Low power dissipation: I CC =1μA (max.) at T A =25 C Power down protection on inputs and
Low noise low drop voltage regulator with shutdown function. Part numbers
Low noise low drop voltage regulator with shutdown function Features Output current up to 150 ma Low dropout voltage (350 mv at I OUT = 50 ma) Very low quiescent current: 0.1 µa in OFF mode and max. 250
STMUX1800L 16- to 8-bit MUX/DEMUX for gigabit Ethernet LAN switch with LED switch and enhanced ESD protection Features Description
16- to 8-bit MUX/DEMUX for gigabit Ethernet LAN switch with LED switch and enhanced ESD protection Features Low R ON : 4.0 Ω typical V CC operating range: 3.0 to 3.6 V Enhanced ESD protection: > 8 kv (contact)
Order codes Package Packaging
Low voltage, low current power 8-bit shift register Features Low voltage power supply down to 3 V 8 constant current output channels Adjustable output current through external resistor Serial data IN/parallel
STMUX1800E. 16-bit to 8-bit MUX/DEMUX for gigabit Ethernet LAN switch with LED switch and enhanced ESD protection. Features. Description.
16-bit to 8-bit MUX/DEMUX for gigabit Ethernet LAN switch with LED switch and enhanced ESD protection Features Low R ON : 4.0 Ω typical V CC operating range: 3.0 to 3.6 V Enhanced ESD protection: > 8 kv
Obsolete Product(s) - Obsolete Product(s)
1-bit dual supply bus buffer level translator with A-side series resistor Features High speed: t PD = 4.4ns (Max.) at T A = 85 C V CCB = 1.65V; V CCA = 3.0V Low power dissipation: I CCA = I CCB = 5µA(Max.)
Order code Temperature range Package Packaging Marking
Single 8-channel analog multiplexer/demultiplexer Datasheet production data Features Low ON resistance: 125 Ω (typ.) Over 15 V p.p signal-input range for: V DD - V EE = 15 V High OFF resistance: channel
STEVAL-ISQ010V1. High-side current-sense amplifier demonstration board based on the TSC102. Features. Description
High-side current-sense amplifier demonstration board based on the TSC102 Data brief Features Independent supply and input common-mode voltages Wide common-mode operating range: 2.8 V to 30 V Wide common-mode
Description. Notes: (1) Qualification and characterization according to AEC Q100 and Q003 or equivalent,
Quad dual-input and gate Datasheet - production data Features SOP14 TSSOP14 High speed: t PD = 7 ns (typ.) at V CC = 6 V Low power dissipation: I CC = 1 µa (max.) at T A = 25 C High noise immunity: V NIH
STMUX3040. NEATSwitch : octal SPDT high bandwidth signal switch. Features. Description. Applications
NEATSwitch : octal SPDT high bandwidth signal switch Features Supports 3.0 Gbps generic data rate Octal SPDT switch to support 2 PCI lanes Low R ON : 5.5 Ω typical Internal voltage regulator V CC operating
Obsolete Product(s) - Obsolete Product(s)
Single 8-channel analog multiplexer/demultiplexer Features Low power dissipation: I CC = 4 μa(max) at T A =25 C Logic level translation to enable 5 V logic signal to communicate with ± 5 V analog signal
Obsolete Product(s) - Obsolete Product(s)
Low voltage 16-Bit, constant current LED sink driver Features Low voltage power supply down to 3V 16 constant current output channels Adjustable output current through external resistor Serial data IN/parallel
2STD1665. Low voltage fast-switching NPN power transistor. Features. Applications. Description
Low voltage fast-switching NPN power transistor Features Very low collector to emitter saturation voltage High current gain characteristic TAB Fast-switching speed Applications Voltage regulators High
ST662AB ST662AC. DC-DC converter from 5 V to 12 V, 0.03 A for Flash memory programming supply. Features. Description
ST662AB ST662AC DC-DC converter from 5 V to 12 V, 0.03 A for Flash memory programming supply Features Output voltage: 12 V ± 5 % Supply voltage range: 4.5 V to 5.5 V Guaranteed output current up to 30
L4940xx5 L4940V5 L4940D2T5-TR 5 V L4940xx85 L4940V85 L4940P85 L4940D2T85-TR 8.5 V L4940xx10 L4940D2T10-TR 10 V L4940xx12 L4940D2T12-TR 12 V
Very low drop 1.5 A regulator Features Precise 5, 8.5, 10, 12 V outputs Low dropout voltage (450 mv typ. at 1 A) Very low quiescent current Thermal shutdown Short circuit protection Reverse polarity protection
Low noise low drop voltage regulator with shutdown function. Part numbers
Low noise low drop voltage regulator with shutdown function Features Output current up to 150 ma Low dropout voltage (350 mv at I OUT = 50 ma) Very low quiescent current: 0.1 µa in OFF mode and max. 250
LET9060C. RF power transistor from the LdmoST family of n-channel enhancement-mode lateral MOSFETs. Features. Description
RF power transistor from the LdmoST family of n-channel enhancement-mode lateral MOSFETs Features Excellent thermal stability Common source configuration P OUT (@ 28 V)= 60 W with 18 db gain @ 945 MHz
3.3 V powered, 15 kv ESD protected, up to 12 Mbps RS-485/ RS-422 transceiver. Description. Table 1. Device summary
3.3 V powered, 15 kv ESD protected, up to 12 Mbps RS-485/ RS-422 transceiver Datasheet - production data Features SO-8 ESD protection ±15 kv IEC 61000-4-2 air discharge ±8 kv IEC 61000-4-2 contact discharge
ESDALCL6-4P6A. Multi-line low capacitance and low leakage current ESD protection. Features. Applications. Description
Multi-line low capacitance and low leakage current ESD protection Features Datasheet production data Diode array topology: 4 lines protection Low leakage current: 10 na at 3 V 1 na at 1 V Very low diode
PD54003L-E. RF power transistor, LdmoST plastic family N-channel enhancement-mode, lateral MOSFETs. Features. Description
RF power transistor, LdmoST plastic family N-channel enhancement-mode, lateral MOSFETs Features Excellent thermal stability Common source configuration P OUT =3 W mith 20dB gain@500 MHz New leadless plastic
Order codes Marking Polarity Package Packaging. MJD44H11T4 MJD44H11 NPN DPAK Tape and reel MJD45H11T4 MJD45H11 PNP DPAK Tape and reel
MJD44H11 MJD45H11 Complementary power transistors Features. Low collector-emitter saturation voltage Fast switching speed Surface-mounting TO-252 (DPAK) power package in tape and reel (suffix "T4") Applications
Gate. Order codes Package Packaging
RF power transistor, LdmoST plastic family N-channel enhancement-mode lateral MOSFETs Datasheet production data Features Excellent thermal stability Common source configuration P OUT = 15 W with 16 db
Description. Table 1. Device summary table. Order code Temperature range Package Packing Marking SO-14. (automotive grade) (1)
QUAD 2-input NAND Schmitt trigger PDIP-14 SO-14 Applications Automotive Industrial Computer Consumer Datasheet - production data Features Schmitt trigger action on each input with no external components
LD1085CXX. 3 A low-drop, adjustable positive voltage regulator. Features. Description
3 A low-drop, adjustable positive voltage regulator Features Typical dropout 1.3 V (at 3 A) Three terminal adjustable output voltage Guaranteed output current up to 3 A Output tolerance ± 2 % at 25 C and
ST202EB - ST202EC ST232EB - ST232EC
ST202EB - ST202EC ST232EB - ST232EC ± 15 kv ESD protected 5 V RS-232 transceiver Features ESD protection for RS-232 I/O pins: ± 15 kv human body model Guaranteed 230 kbps date rate Guaranteed slew rate
STD1802T4-A. Low voltage fast-switching NPN power transistor. Features. Description. Applications
Low voltage fast-switching NPN power transistor Features This device is qualified for automotive application Very low collector to emitter saturation voltage High current gain characteristic Fast-switching
ST619LBDR. DC-DC converter regulated 5 V charge pump. Features. Description
DC-DC converter regulated 5 V charge pump Features Regulated 5 V ±4 % charge pump Output current guaranteed over temperature: 20 ma (V I 2 V), 30 ma (V I 3 V) No inductors; very low EMI noise Uses small,
TS3704. Micropower quad CMOS voltage comparators. Features. Description
Micropower quad CMOS voltage comparators Features Push-pull CMOS output (no external pull-up resistor required) Extremely low supply current: 9μa typ per comparator Wide single supply range 2.7V to 6V
MJE182 Low voltage high speed switching NPN transistor Features Applications Description High speed switching NPN device
Low voltage high speed switching NPN transistor Features High speed switching NPN device Applications Audio amplifier High speed switching applications Description This device is an NPN low voltage transistor
R 1 typ. = 15 kω. Order codes Marking Polarity Package Packaging. 2N6036 2N6036 NPN SOT-32 Tube 2N6039 2N6039 PNP SOT-32 Tube
2N6036 2N6039 Complementary power Darlington transistors Features. Good h FE linearity High f T frequency Monolithic Darlington configuration with integrated antiparallel collector-emitter diode Applications
Order codes Package Packaging
Low voltage 16-bit constant current LED sink driver Features Low voltage power supply down to 3 V 16 constant current output channels Adjustable output current through external resistor Serial data IN/parallel
2STR SOT-23 Tape and reel 2STR1230G 130G SOT-23 Tape and reel
Low voltage fast-switching NPN power transistor Features Very low collector-emitter saturation voltage High current gain characteristic Fast switching speed Miniature SOT-23 plastic package for surface
Obsolete Product(s) - Obsolete Product(s)
N-channel 30 V, 0.012 Ω, 8 A - PowerFLAT (3.3x3.3) ultra low gate charge STripFET Power MOSFET Features Type V DSS R DS(on) I D 30V
D44H8 - D44H11 D45H8 - D45H11
D44H8 - D44H11 D45H8 - D45H11 Complementary power transistors Features. Low collector-emitter saturation voltage Fast switching speed TAB Applications Power amplifier Switching circuits 1 2 3 Description
STP16CPS05. Low voltage 16-Bit constant current LED sink driver with auto power saving. Features. Description. Order codes
Low voltage 16-Bit constant current LED sink driver with auto power saving Features Low voltage power supply down to 3V 16 constant current output channels Adjustable output current through external resistor
STN9260. High voltage fast-switching PNP power transistor. Features. Applications. Description. High voltage capability Fast switching speed
High voltage fast-switching PNP power transistor Features High voltage capability Fast switching speed Applications Lighting Switch mode power supply Description This device is a high voltage fast-switching
BUX87. High voltage NPN power transistor. Features. Applications. Description
High voltage NPN power transistor Features High voltage capability (450 V V CEO ) Minimum lot-to-lot spread for reliable operation High DC current gain Applications Flyback and forward single transistor
Obsolete Product(s) - Obsolete Product(s)
Low voltage fast-switching PNP power transistor Features Very low collector-emitter saturation voltage High current gain characteristic Fast switching speed 3 Miniature SOT-23 plastic package for surface
2STR2215. Low voltage fast-switching PNP power transistor. Features. Applications. Description
Low voltage fast-switching PNP power transistor Features Very low collector-emitter saturation voltage High current gain characteristic Fast switching speed Miniature SOT-23 plastic package for surface
3STL2540. Low voltage high performance PNP power transistor. Features. Applications. Description
Low voltage high performance PNP power transistor Datasheet production data Features Very low collector-emitter saturation voltage High current gain characteristic Small, thin, leadless SMD plastic package
Description. Table 1. Device summary. Order code Temp. range Package Packing Marking
Quad 2-input Schmitt NAND gate Datasheet - production data SO14 TSSOP14 Wide operating voltage range: V CC (opr) = 2 V to 6 V Pin and function compatible with 74 series 132 ESD performance HBM: 2 kv MM:
LK115XX30 LK115XX33 - LK115XX50
LK115XX30 LK115XX33 - LK115XX50 ery low drop with inhibit voltage regulators Features ery low dropout voltage (0.2 typ.) ery low quiescent current (Typ. 0.01 µa in off mode, 280 µa in on mode) Output current
STG3220. Low voltage high bandwidth dual SPDT switch. Features. Description. Applications
Low voltage high bandwidth dual SPDT switch Features Ultra low power dissipation: I CC = 1 μa (max.) at T A = 85 C Low "ON" resistance: R ON = 4.8 Ω (T A = 25 ºC) at V CC = 4.3 V R ON = 5.9 Ω (T A = 25
L6221. Quad Darlington switch. Features. Applications. Description
L6221 Quad Darlington switch Features Four non-inverting inputs with enable Output voltage up to 50 V Output current up to 1.8 A Very low saturation voltage TTL compatible inputs Integral fast recirculation
BD235 BD237. Low voltage NPN power transistors. Features. Applications. Description. Low saturation voltage NPN transistors
BD235 BD237 Low voltage NPN power transistors Features Low saturation voltage NPN transistors Applications Audio, power linear and switching applications Description The devices are manufactured in Planar
LD1117Axx. Low drop fixed and adjustable positive voltage regulators. Features. Description
Low drop fixed and adjustable positive voltage regulators Features Low dropout voltage (1.15 V typ. @ I OUT = 1 A, 25 C) Very low quiescent current (5 ma typ. @ 25 C) Output current up to 1 A Fixed output
ST26025A. PNP power Darlington transistor. Features. Applications. Description
ST26025A PNP power Darlington transistor Features High current monolithic Darlington configuration Integrated antiparallel collector-emitter diode Applications Automotive fan control Linear and switching
RefTitle1 PD84008L-E. RF power transistor, LdmoST plastic family N-channel enhancement-mode lateral MOSFETs. Features. Description
RefTitle1 PD848L-E RF power transistor, LdmoST plastic family N-channel enhancement-mode lateral MOSFETs Features Excellent thermal stability Common source configuration P OUT = 8 W with 13 db gain @ 87
LM2903W. Low-power, dual-voltage comparator. Features. Description
Low-power, dual-voltage comparator Datasheet production data Features Wide, single supply voltage range or dual supplies +2 V to +36 V or ±1 V to ±18 V Very low supply current (0.4 ma) independent of supply
LM2903H. Low-power dual voltage comparator. Features. Description
LM23H Low-power dual voltage comparator Datasheet production data Features Wide single supply voltage range or dual supplies +2 V to +36 V or ±1 V to ±18 V Very low supply current (0.4 ma) independent
2STA1695. High power PNP epitaxial planar bipolar transistor. Features. Applications. Description
High power PNP epitaxial planar bipolar transistor Features High breakdown voltage V CEO = -140 V Complementary to 2STC4468 Typical f t = 20 MHz Fully characterized at 125 C Applications 1 2 3 Audio power
ETP01-xx21 Protection for Ethernet lines Features Description Applications Benefits Complies with the following standards
Protection for Ethernet lines Features Differential and common mode protection Telcordia GR089 Intrabuilding: 50 A, 2/0 µs ITU-T K20/2: 40 A, 5/30 µs Low capacitance: 3 pf max at 0 V UL94 V0 approved resin
Obsolete Product(s) - Obsolete Product(s)
2 W mono amplifier Features 2 W output power into 8 Ω at 12 V, THD = 10% Internally fixed gain of 32 db No feedback capacitor No boucherot cell Thermal protection AC short-circuit protection SVR capacitor
Part numbers Order codes Description Packages
ULQ2001 ULQ2003 - ULQ2004 Seven Darlington array Features Seven Darlington per package Extended temperature range: -40 to 105 C Output current 500 ma per driver (600 ma peak) Output voltage 50 V Automotive
SPV1001T40. Cool bypass switch for photovoltaic application. Features. Application. Description TO-220
Cool bypass switch for photovoltaic application Features I F =16 A, V R = 40 V Very low forward voltage drop Very low reverse leakage current 150 C operating junction temperature +4 Application Photovoltaic
Order codes Marking Package Packaging. STD2805T4 D2805 DPAK Tape & reel STD D2805 IPAK Tube. June 2007 Rev 1 1/9
Low voltage fast-switching PNP power transistor Preliminary Data Features Very low collector to emitter saturation voltage High current gain characteristic Fast-switching speed Surface-mounting DPAK (TO-252)
2STD1360 2STF1360-2STN1360
2STD1360 2STF1360-2STN1360 Low voltage fast-switching NPN power transistors Features Very low collector-emitter saturation voltage High current gain characteristic Fast-switching speed 4 1 2 3 4 1 3 2
STPSC V power Schottky silicon carbide diode. Features. Description
600 V power Schottky silicon carbide diode Features No or negligible reverse recovery Switching behavior independent of temperature Particularly suitable in PFC boost diode function Description The SiC
Description. Table 1. Device summary. Order code Temp. range Package Packing Marking
9-bit parity generator Datasheet - production data Features SO14 TSSOP14 High-speed: t PD = 22 ns (typ.) at V CC = 6 V Low power dissipation: I CC = 4 μa (max.) at T A = 25 C High noise immunity: V NIH
TSL channel buffers for TFT-LCD panels. Features. Application. Description
14 + 1 channel buffers for TFT-LCD panels Datasheet production data Features Wide supply voltage: 5.5 V to 16.8 V Low operating current: 6 ma typical at 25 C Gain bandwidth product: 1 MHz High current
LExxAB LExxC. Very low dropout voltage regulators with inhibit function. Features. Description
LExxAB LExxC ery low dropout voltage regulators with inhibit function Datasheet production data Features ery low dropout voltage (0.2 typ.) ery low quiescent current (typ. 50 µa in OFF mode, 0.5 ma in
Obsolete Product(s) - Obsolete Product(s) Obsolete Product(s) - Obsolete Product(s)
5 A low dropout fast response positive voltage regulator adjustable Features Typical dropout 1.2 V Fast transient response Three terminal adjustable Guaranteed output current up to 5 A Output tolerance
LDS3985xx. Ultra low drop-low noise BiCMOS 300 ma voltage regulator for use with very low ESR output capacitor. Features.
Ultra low drop-low noise BiCMOS 300 ma voltage regulator for use with very low ESR output capacitor Features Input voltage from 2.5 V to 6 V Stable with low ESR ceramic capacitors Ultra low dropout voltage
TS391. Low-power single voltage comparator. Features. Description
Low-power single voltage comparator Datasheet production data Features Wide single supply voltage range or dual supplies +2 V to +36 V or ±1 V to ±18 V Very low supply current (0.2 ma) independent of supply
2STN2540. Low voltage fast-switching PNP power bipolar transistor. Features. Applications. Description
2STN2540 Low voltage fast-switching PNP power bipolar transistor Features Very low collector-emitter saturation voltage High current gain characteristic Fast switching speed Surface mounting device in
BD533 BD535 BD537 BD534 BD536
BD533 BD535 BD537 BD534 BD536 Complementary power transistors Features. BD533, BD535, and BD537 are NPN transistors Description The devices are manufactured in Planar technology with Base Island layout.
STG3692. Low voltage high bandwidth quad SPDT switch. Features. Description
Low voltage high bandwidth quad SPDT switch Features Ultra low power dissipation: I CC = 0.2 µa (max.) at T A = 85 C Low ON resistance: R ON = 4.6 Ω (T A = 25 C) at V CC = 4.3 V R ON = 5.8 Ω (T A = 25
SD1728 (TH430) RF & Microwave transistors HF SSB application. Features. Description. Pin connection
SD1728 (TH430) RF & Microwave transistors HF SSB application Features 13.56MHz 44V Gold metallization Common emitter P OUT = 200W with 15dB gain Description The SD1728 is a 50V epitaxial silicon NPN planar
Obsolete Product(s) - Obsolete Product(s)
High power PNP epitaxial planar bipolar transistor Features High breakdown voltage V CEO = -120 V Complementary to 2STC4467 Fast-switching speed Typical f t = 20 MHz Fully characterized at 125 o C Applications
BD241A BD241C. NPN power transistors. Features. Applications. Description. NPN transistors. Audio, general purpose switching and amplifier transistors
BD241A BD241C NPN power transistors Features. NPN transistors Applications Audio, general purpose switching and amplifier transistors Description The devices are manufactured in Planar technology with
ESDARF03-1BF3. Ultralow capacitance ESD protection for antenna. Features. Applications. Description. Benefits. Complies with the following standards
Ultralow capacitance ESD protection for antenna Features ultralow diode capacitance 0.6 pf Single line, protected against 15 kv ESD breakdown voltage V BR = 6.0 V min. Flip Chip 400 µm pitch, lead-free
LD1085xx. 3 A low drop positive voltage regulator adjustable and fixed. Features. Description
3 A low drop positive voltage regulator adjustable and fixed Features Typical dropout 1.3 V (at 3 A) Three terminal adjustable or fixed output voltage 1.5 V, 1.8 V, 2.5 V, 3.3 V, 5 V, 12 V. Automotive
ST3237EBDR -40 to 85 C SO-28 (tape and reel) 1000 parts per reel ST3237EBPR -40 to 85 C SSOP28 (tape and reel) 1350 parts per reel
± 15 kv ESD protected, 1 µa, 3 to 5.5 V, 250 kbps RS-232 transceiver with stand-by Features ESD protection for RS-232 I/O pins ±15 kv human body model ±8 kv IEC 1000-4-2 contacts discharge 1 µa low power
Obsolete Product(s) - Obsolete Product(s)
2N6284 2N6287 Complementary power Darlington transistors Features Complementary transistors in monolithic Darlington configuration Integrated collector-emitter antiparallel diode Applications Audio power
EVAL-RHF310V1. EVAL-RHF310V1 evaluation board. Features. Description
evaluation board Data brief Features Mounted Engineering Model RHF310K1: Rad-hard, 120 MHz, operational amplifier (see RHF310 datasheet for further information) Mounted components (ready-to-use) Material:
LD A, very low drop voltage regulators. Features. Description. Table 1. Device summary
3 A, very low drop voltage regulators Datasheet - production data Table 1. Device summary Order codes LD29300P2M33R LD29300P2MTR Output voltages 3.3 V ADJ P²PAK/A Features Very low dropout voltage (typ.