Obsolete Product(s) - Obsolete Product(s)
|
|
|
- Darleen Arlene Wheeler
- 6 years ago
- Views:
Transcription
1 Single bilateral switch Features High speed: t PD = 0.3 ns (typ.) at V CC = 5 V t PD = 0.4 ns (typ.) at V CC = 3.3 V Low power dissipation: I CC = 1 μa (max.) at T A =25 C Low "ON" resistance: R ON =6.5Ω (typ.) at V CC = 5 V I I/O = 1 ma R ON = 8.5 Ω (typ.) at V CC = 3.3 V I I/O = 1 ma Sine wave distortion: 0.04% at V CC = 3.3V f = 1kHz Wide operating range: V CC (opr) = 2 V to 5.5 V Improved latch-up immunity Description The 74V1G66 is an advanced high-speed CMOS single bilateral switch fabricated in silicon gate C 2 MOS technology. It achieves high speed propagation delay and very low ON resistances while maintaining true CMOS low power consumption. This bilateral switch handles rail to rail analog and digital signals that may vary across the full power supply range (from GND to V CC ). The C input is provided to control the switch and it is compatible with standard CMOS outputs. The switch is ON (port I/O is connected to port O/I) when the C input is held high and OFF (high impedance state exists between the two ports) when C is held low. It can be used in many applications as battery powered systems or test equipments. SOT23-5L SOT323-5L The 74V1G66 is available in the commercial and extended temperature range in SOT23-5L and SOT323-5L packages. All inputs and outputs are equipped with protection circuits against static discharge, giving them ESD immunity and transient excess voltage. Table 1. Device summary Order code Package Packaging 74V1G66STR SOT23-5L Tape and reel 74V1G66CTR SOT323-5L Tape and reel October 2008 Rev 8 1/
2 Pin connection 74V1G66 1 Pin connection Figure 1. Pin connection and IEC logic symbols Table 2. Figure 2. Pin description Pin number Symbol Name and function 1 I/O Independent input/output 2 O/I Independent output/input 3 GND Ground (0 V) 4 C Enable input (active high) 5 V CC Positive supply voltage Input equivalent circuit Table 3. Truth table Control Switch function H ON L OFF (1) 1. High impedance state. 2/15
3 Maximum rating 2 Maximum rating Stressing the device above the rating listed in the Absolute Maximum Ratings table may cause permanent damage to the device. These are stress ratings only and operation of the device at these or any other conditions above those indicated in the Operating sections of this specification is not implied. Exposure to Absolute Maximum Rating conditions for extended periods may affect device reliability. Table 4. Absolute maximum ratings Symbol Parameter Value Unit V CC Supply voltage -0.5 to +7.0 V V I DC input voltage -0.5 to V CC V V IC DC control input voltage -0.5 to +7.0 V V O DC Output voltage -0.5 to V CC V I IK DC input diode current ± 20 ma I IK DC control input diode current - 20 ma I OK DC output diode current ± 20 ma I O DC output current ± 50 ma I CC or I GND DC V CC or ground current ± 50 ma T stg Storage temperature -65 to +150 C T L Lead temperature (10 sec) 300 C Table 5. Recommended operating conditions Symbol Parameter Value Unit V CC Supply voltage 2 to 5.5 V V I Input voltage 0 to V CC V V IC Control input voltage 0 to 5.5 V V O Output voltage 0 to V CC V T op Operating temperature -55 to 125 C dt/dv Input rise and fall time (1) V CC = 5.0 V 1. V IN from 30% to 70% of V CC on control pin. 0 to 20 ns/v 3/15
4 Maximum rating 74V1G66 Table 6. DC specifications Test condition Value Symbol Parameter V CC (V) T A = 25 C -40 to 85 C -55 to 125 C Min Typ Max Min Max Min Max Unit V IH V IL R ON R ON I OFF I IZ I IN I CC High level input voltage Low level input voltage ON resistance ON resistance Input/output leakage current (switch OFF) Switch input leakage current (switch ON, output open) Control input leakage current Quiescent supply current 1. Voltage range is 3.3 V ± 0.3 V. 2. Voltage range is 5 V ± 0.5 V to V C C 0.7V CC 0.7V CC to V C C 0.3V CC 0.3V CC 3.3 (1) V IC = V IH V I/O = V CC to 5.0 (2) GND I I/O 1mA (1) V IC = V IH V I/O = V CC or 5.0 (2) GND I I/O 1mA to V OS = V CC to GND V IS = V CC to GND V IC = V IL ±0.1 ± 1 ± 5 μa V OS = V CC to GND ±0.1 ± 1 ± 5 μa V IC = V IH V IC = 5.5V or GND V I = V CC or GND ± 0.1 ± 1.0 ± 1.0 μa μa V V Ω Ω 4/15
5 Maximum rating Table 7. AC electrical characteristics (C L = 50 pf, input t r = t f = 3 ns) Test condition Value Symbol Parameter V CC (V) T A = 25 C -40 to 85 C -55 to 125 C Min Typ Max Min Max Min Max Unit 3.3 (1) t PD Delay time t r = t f = 6 ns 5.0 (2) t PLZ Output disable 3.3 (1) R t PHZ time L = 500 Ω 5.0 (2) t PZL Output enable time 3.3(1) R t L = 1 KΩ PZH 5.0 (2) Voltage range is 3.3 V ± 0.3 V. 2. Voltage range is 5 V ± 0.5 V. Table 8. Symbol Capacitive characteristics Parameter V CC (V) Test condition Value T A = 25 C -40 to 85 C -55 to 125 C Min Typ Max Min Max Min Max C IN Input capacitance pf C I/O Output capacitance 10 pf C PD Power dissipation capacitance (1) C PD is defined as the value of the IC s internal equivalent capacitance which is calculated from the operating current consumption without load. (Refer to the test circuit). Average operating current can be obtained by the following equation. I CC (opr) = C PD x V CC x f IN + I CC. ns ns ns Unit pf 5/15
6 Maximum rating 74V1G66 Table 9. Symbol f MAX Analog switch characteristics (GND = 0 V; T A = 25 C) Parameter Sine wave distortion (THD) Frequency response (switch ON) Feed through attenuation (switch OFF) Crosstalk (control input to signal output) 1. Voltage range is 3.3 V ± 0.3 V 2. Voltage range is 5.0 V ± 0.5 V V CC (V) V IN (V p- p ) Test condition Valu e 3.3 (1) f IN = 1 KHz R L = 10 KΩ, C L = 50 pf 5.0 (2) Typ 3.3 (1) Adjust f IN voltage to obtain 0 dbm at V OS (2) Increase f IN Frequency until db meter reads -3dB R L = 50 Ω, C L = 10 pf (1) V IN is centered at V CC / (2) Adjust f IN Voltage to obtained 0dBm at V IS R L = 600Ω, C L = 50 pf, f IN = 1KHz sine wave (1) R L = 600 Ω, C L = 50 pf, f IN = 1 KHz square wave (2) t r = t f = 6 ns 60 Unit % MHz db mv 6/15
7 Switching characteristics test circuit 3 Switching characteristics test circuit Figure 3. Enable and disable timing (circuit) Figure 4. Enable and disable timing (waveform) Figure 5. Resistive feedthrough attenuation Figure 6. Capacitive feedthrough attenuation AM00744V1 Figure 7. Bandwidth attenuation Figure 8. Maximum control frequency 7/15
8 Switching characteristics test circuit 74V1G66 Figure 9. Crosstalk (control to output) Figure 10. Channel resistance (R ON ) Figure 11. I CC (opr) 8/15
9 Package mechanical data 4 Package mechanical data In order to meet environmental requirements, ST offers these devices in ECOPACK packages. These packages have a Lead-free second level interconnect. The category of second level interconnect is marked on the package and on the inner box label, in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering conditions are also marked on the inner box label. ECOPACK is an ST trademark. ECOPACK specifications are available at: 9/15
10 Package mechanical data 74V1G66 SOT23-5L MECHANICAL DATA DIM. mm. MIN. TYP MAX. MIN. TYP. MAX. mils A A A b C D E e H L C 10/15
11 Package mechanical data SOT323-5L MECHANICAL DATA DIM. mm. mils MIN. TYP MAX. MIN. TYP. MAX. A A A b C D E E e e L /15
12 Package mechanical data 74V1G66 Tape & Reel SOT23-xL MECHANICAL DATA DIM. mm. inch MIN. TYP MAX. MIN. TYP. MAX. A C D N T Ao Bo Ko Po P /15
13 Package mechanical data Tape & Reel SOT323-xL MECHANICAL DATA DIM. mm. inch MIN. TYP MAX. MIN. TYP. MAX. A C D N T Ao Bo Ko Po P /15
14 Revision history 74V1G66 5 Revision history Table 10. Document revision history Date Revision Changes 01-Apr Updated data reel information. 28-Oct Document reformatted to improve readability. Updated Table 6: DC specifications on page 4. 14/15
15 Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries ( ST ) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan - Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America 15/15
74V2G66STR DUAL BILATERAL SWITCH
DUAL BILATERAL SWITCH HIGH SPEED: t PD = 0.3ns (TYP.) at V CC =5V t PD = 0.4ns (TYP.) at V CC =3.3V LOW POWER DISSIPATION: I CC =1µA(MAX.) at T A = 25 C LOW "ON" RESISTANCE: R ON =6.5Ω (TYP.) AT V CC =5VI
Obsolete Product(s) - Obsolete Product(s)
Single buffer/driver with open drain Features 5 V tolerant inputs High speed: t PD = 4.2 ns (max.) at V CC = 3.3 V Low power dissipation: I CC =1μA (max.) at T A =25 C Power down protection on inputs and
Obsolete Product(s) - Obsolete Product(s)
Single 8-channel analog multiplexer/demultiplexer Features Low power dissipation: I CC = 4 μa(max) at T A =25 C Logic level translation to enable 5 V logic signal to communicate with ± 5 V analog signal
Obsolete Product(s) - Obsolete Product(s)
Low voltage CMOS octal bus buffer (3-state) with 5V tolerant inputs and outputs Features 5V tolerant inputs and outputs High speed: t PD = 8.0ns (Max) at V CC = 3V Power down protection on inputs and outputs
74LCX139 Low voltage CMOS Dual 2 to 4 decoder / demultiplexer Features Description Order codes
Low voltage CMOS Dual 2 to 4 decoder / demultiplexer Features 5V tolerant inputs High speed: t PD = 6.2ns (Max) at V CC = 3V Power down protection on inputs and outputs Symmetrical output impedance: I
Obsolete Product(s) - Obsolete Product(s)
Low power single inverter gate Features High speed: t PD = 4.3 ns (max.) at V CC = 2.3 V Power down protection on inputs and outputs Balanced propagation delays: t PLH t PHL Operating voltage range: V
Obsolete Product(s) - Obsolete Product(s)
1-bit dual supply bus buffer level translator with A-side series resistor Features High speed: t PD = 4.4ns (Max.) at T A = 85 C V CCB = 1.65V; V CCA = 3.0V Low power dissipation: I CCA = I CCB = 5µA(Max.)
Description. Order code Temperature range Package Packaging Marking
Low-voltage CMOS quad bus buffer (3-state) with 5 V tolerant inputs and outputs Datasheet production data Features 5 V tolerant inputs and outputs High speed t PD = 5.2 ns (max.) at V CC = 3 V Power-down
Order codes Temperature range Package Packaging
CMOS quad 3-state differential line driver Features TTL input compatible Typical propagation delay: 6 ns Typical output skew: 0.5 ns Output will not load line when V CC = 0 V Meets the requirements of
STG3699B. Low voltage 0.5 Ω max, quad SPDT switch with break-before-make feature. Features. Description
Low voltage 0.5 Ω max, quad SPDT switch with break-before-make feature Features High speed: t PD = 1.5 ns (typ.) at V CC = 3.0 V t PD = 1.5 ns (typ.) at V CC = 2.3 V Ultra low power dissipation: I CC =0.2μA
STG5682. Low voltage dual SPDTswitch with negative rail capability. Features. Description
Low voltage dual SPDTswitch with negative rail capability Features Distortion-free negative signal throughput down to V CC -5.5V Wide operating voltage range: V CC (Opr) = 1.65V to 4.5V single supply Ultra
Order codes Temperature range Package Packaging
CMOS quad 3-state differential line receiver Features CMOS design for low power ± 0.2 V sensitivity over input common mode voltage range Typical propagation delay: 19 ns Typical input hysteresis: 60 mv
Obsolete Product(s) - Obsolete Product(s)
High bandwidth analog switch with 16-to-8 bit MUX/DEMUX Features Low R ON : 5.5 Ω typical V CC operating range: 3.0 to 3.6 V Low current consumption: 20 µa ESD HBM model: > 2 kv Channel on capacitance:
Single 8-channel analog MUX/DEMUX with injection current protection. Description. Order code Temperature range Package Packaging Marking
Features Single 8-channel analog MUX/DEMUX with injection current protection Datasheet production data Low power dissipation I CC = 2 μa (max.) at T A = 25 C Injection current protection V ΔOUT < 1 mv
STG719 LOW VOLTAGE 4Ω SPDT SWITCH
LOW VOLTAGE 4Ω SPDT SWITCH HIGH SPEED: t PD = 0.3ns (TYP.) at V CC = 5V t PD = 0.4ns (TYP.) at V CC = 3.3V LOW POWER DISSIPATION: I CC = 1µA(MAX.) at T A =25 C LOW "ON" RESISTANCE: R ON = 4Ω (MAX. T A
Obsolete Product(s) - Obsolete Product(s)
High speed differential line receivers Features Meets or exceeds the requirements of ansi TIA/EIA-644 standard Operates with a single 3.3 V supply Designed for signaling rate up to 400 Mbps Differential
Obsolete Product(s) - Obsolete Product(s)
High bandwidth switch with 20- to 10-bit MUX/DEMUX Datasheet - production data Features Low R ON : 4.0 Ω typical V CC operating range: 3.0 to 3.6 V Enhanced ESD protection: > 8 kv (contact) and 15 kv (HBM)
Obsolete Product(s) - Obsolete Product(s)
SINGLE INVERTER (OPEN DRAIN) HIGH SPEED: t PD = 3.7ns (TYP.) at V CC =5V LOW POWER DISSIPATION: I CC =1µA(MAX.) at T A =25 C HIGH NOISE IMMUNITY: V NIH =V NIL = 28% V CC (MIN.) POWER DOWN PROTECTION ON
HCF4093. QUAD 2-input NAND Schmidt trigger. Features. Description
QUAD 2-input NAND Schmidt trigger Features Schmidt trigger action on each input with no external components Hysteresis voltage typically 0.9 V at V DD =5V and 2.3 V at V DD =10 V Noise immunity greater
Obsolete Product(s) - Obsolete Product(s)
High speed differential line drivers Features Meets or exceeds the requirements of ANSI TIA/EIA-644 standard Low voltage differential signaling with typical output voltage of 350 mv and a 100 Ω load Typical
Description. Table 1. Device summary. Order code Temp. range Package Packing Marking
Hex bus buffer with 3-state outputs (non-inverting) Datasheet - production data Features SO16 TSSOP16 High-speed: t PD = 10 ns (typ.) at V CC = 6 V Low power dissipation: I CC = 4 μa (max.) at T A = 25
Description. Table 1. Device summary. Order code Temp. range Package Packaging Marking
Quad bus buffer (3-state) Datasheet - production data Features SO14 TSSOP14 High-speed: t PD = 8 ns (typ.) at V CC = 6 V Low power dissipation: I CC = 4 μa (max.) at T A = 25 C High noise immunity: V NIH
Low noise low drop voltage regulator with shutdown function. Part numbers
Low noise low drop voltage regulator with shutdown function Features Output current up to 150 ma Low dropout voltage (350 mv at I OUT = 50 ma) Very low quiescent current: 0.1 µa in OFF mode and max. 250
ST485AB. Very high speed low power RS-485/RS-422 transceiver. Features. Description
Very high speed low power RS-485/RS-422 transceiver Features Low supply current: 5 ma max High data rate > 30 Mbps Designed for RS 485 interface applications -7 to 12 common mode input voltage range Driver
Obsolete Product(s) - Obsolete Product(s)
High speed differential line drivers and receivers Feature summary Meets or exceed the requirements of ansi eia/tia-644-1995 standard Signaling rates up to 400Mbit/s Bus terminal ESD exceeds 6kV Operates
Obsolete Product(s) - Obsolete Product(s)
SINGLE BUS BUFFER (3-STATE) HIGH SPEED: t PD = 3.8ns (TYP.) at V CC =5V LOW POWER DISSIPATION: I CC =1µA (MAX.)atT A =25 C HIGH NOISE IMMUNITY: V NIH =V NIL = 28% V CC (MIN.) POWER DOWN PROTECTION ON INPUTS
Order code Temperature range Package Packaging Marking
Single 8-channel analog multiplexer/demultiplexer Datasheet production data Features Low ON resistance: 125 Ω (typ.) Over 15 V p.p signal-input range for: V DD - V EE = 15 V High OFF resistance: channel
STMUX3040. NEATSwitch : octal SPDT high bandwidth signal switch. Features. Description. Applications
NEATSwitch : octal SPDT high bandwidth signal switch Features Supports 3.0 Gbps generic data rate Octal SPDT switch to support 2 PCI lanes Low R ON : 5.5 Ω typical Internal voltage regulator V CC operating
Description. Notes: (1) Qualification and characterization according to AEC Q100 and Q003 or equivalent,
Quad dual-input and gate Datasheet - production data Features SOP14 TSSOP14 High speed: t PD = 7 ns (typ.) at V CC = 6 V Low power dissipation: I CC = 1 µa (max.) at T A = 25 C High noise immunity: V NIH
74V1G77CTR SINGLE D-TYPE LATCH
SINGLE D-TYPE LATCH HIGH SPEED: t PD = 4.4ns (TYP.) at V CC =5V LOW POWER DISSIPATION: I CC =1µA(MAX.) at T A =25 C HIGH NOISE IMMUNITY: V NIH =V NIL = 28% V CC (MIN.) POWER DOWN PROTECTION ON INPUTS SYMMETRICAL
Part number Temperature range Package Packaging
ST1480AB ST1480AC 3.3 V powered, 15 kv ESD protected, up to 12 Mbps true RS-485/RS-422 transceiver Features ESD protection ±15 kv human body model ±8 kv IEC 1000-4-2 contact discharge Operate from a single
74V1G79CTR SINGLE POSITIVE EDGE TRIGGERED D-TYPE FLIP-FLOP
SINGLE POSITIVE EDGE TRIGGERED D-TYPE FLIP-FLOP HIGH SPEED: f MAX = 180MHz (TYP.) at V CC =5V LOW POWER DISSIPATION: I CC =1µA(MAX.) at T A =25 C HIGH NOISE IMMUNITY: V NIH =V NIL = 28% V CC (MIN.) POWER
STG3220. Low voltage high bandwidth dual SPDT switch. Features. Description. Applications
Low voltage high bandwidth dual SPDT switch Features Ultra low power dissipation: I CC = 1 μa (max.) at T A = 85 C Low "ON" resistance: R ON = 4.8 Ω (T A = 25 ºC) at V CC = 4.3 V R ON = 5.9 Ω (T A = 25
Order code Temperature range Package Packaging
Low power high speed RS-485/RS-422 transceiver Features Low supply current: 5 ma max -7 V to 12 V common mode input voltage range 70 mv typical input hysteresis Designed for 25 Mbps operation Operate from
Obsolete Product(s) - Obsolete Product(s)
SINGLE 2-INPUT NOR GATE HIGH SPEED: t PD = 3.6ns (TYP.) at V CC =5V LOW POWER DISSIPATION: I CC =1µA(MAX.) at T A =25 C HIGH NOISE IMMUNITY: V NIH =V NIL = 28% V CC (MIN.) POWER DOWN PROTECTION ON INPUTS
STMUX1800E. 16-bit to 8-bit MUX/DEMUX for gigabit Ethernet LAN switch with LED switch and enhanced ESD protection. Features. Description.
16-bit to 8-bit MUX/DEMUX for gigabit Ethernet LAN switch with LED switch and enhanced ESD protection Features Low R ON : 4.0 Ω typical V CC operating range: 3.0 to 3.6 V Enhanced ESD protection: > 8 kv
ST619LBDR. DC-DC converter regulated 5 V charge pump. Features. Description
DC-DC converter regulated 5 V charge pump Features Regulated 5 V ±4 % charge pump Output current guaranteed over temperature: 20 ma (V I 2 V), 30 ma (V I 3 V) No inductors; very low EMI noise Uses small,
LK115XX30 LK115XX33 - LK115XX50
LK115XX30 LK115XX33 - LK115XX50 ery low drop with inhibit voltage regulators Features ery low dropout voltage (0.2 typ.) ery low quiescent current (Typ. 0.01 µa in off mode, 280 µa in on mode) Output current
74V1G00CTR SINGLE 2-INPUT NAND GATE
SINGLE 2-INPUT NAND GATE HIGH SPEED: t PD = 3.7ns (TYP.) at V CC =5V LOW POWER DISSIPATION: I CC =1µA(MAX.) at T A =25 C HIGH NOISE IMMUNITY: V NIH =V NIL = 28% V CC (MIN.) POWER DOWN PROTECTION ON INPUTS
STG3692. Low voltage high bandwidth quad SPDT switch. Features. Description
Low voltage high bandwidth quad SPDT switch Features Ultra low power dissipation: I CC = 0.2 µa (max.) at T A = 85 C Low ON resistance: R ON = 4.6 Ω (T A = 25 C) at V CC = 4.3 V R ON = 5.8 Ω (T A = 25
L4940xx5 L4940V5 L4940D2T5-TR 5 V L4940xx85 L4940V85 L4940P85 L4940D2T85-TR 8.5 V L4940xx10 L4940D2T10-TR 10 V L4940xx12 L4940D2T12-TR 12 V
Very low drop 1.5 A regulator Features Precise 5, 8.5, 10, 12 V outputs Low dropout voltage (450 mv typ. at 1 A) Very low quiescent current Thermal shutdown Short circuit protection Reverse polarity protection
KF25B, KF33B KF50B, KF80B
KF25B, KF33B KF50B, KF80B Very low drop voltage regulators with inhibit Datasheet production data Features Very low dropout voltage (0.4 V) Very low quiescent current (typ. 50 µa in OFF mode, 500 µa in
ESDALCL6-4P6A. Multi-line low capacitance and low leakage current ESD protection. Features. Applications. Description
Multi-line low capacitance and low leakage current ESD protection Features Datasheet production data Diode array topology: 4 lines protection Low leakage current: 10 na at 3 V 1 na at 1 V Very low diode
Part number Temperature range Package Packaging
Low power RS-485/RS-422 transceiver General features Low quiescent current: 300µA Designed for RS-485 interface application -7V to 12V common mode input voltage range Driver maintains high impedance in
74V1T07CTR SINGLE BUFFER (OPEN DRAIN)
SINGLE BUFFER (OPEN DRAIN) HIGH SPEED: t PD = 4.3ns (TYP.) at V CC = 5V LOW POWER DISSIPATION: I CC = 1µA(MAX.) at T A =25 C COMPATIBLE WITH TTL OUTPUTS: V IH = 2V (MIN), V IL = 0.8V (MAX) POWER DOWN PROTECTION
Low noise low drop voltage regulator with shutdown function. Part numbers
Low noise low drop voltage regulator with shutdown function Features Output current up to 150 ma Low dropout voltage (350 mv at I OUT = 50 ma) Very low quiescent current: 0.1 µa in OFF mode and max. 250
74LVX257 LOW VOLTAGE CMOS QUAD 2 CHANNEL MULTIPLEXER (3-STATE) WITH 5V TOLERANT INPUTS
LOW VOLTAGE CMOS QUAD 2 CHANNEL MULTIPLEXER (3-STATE) WITH 5V TOLERANT INPUTS HIGH SPEED: t PD =5.8ns (TYP.) at V CC = 3.3V 5V TOLERANT INPUTS POWER-DOWN PROTECTION ON INPUTS INPUT VOLTAGE LEVEL: V IL
Obsolete Product(s) - Obsolete Product(s)
TRIPLE 3-INPUT NOR GATE HIGH SPEED: t PD = 4.1 ns (TYP.) at V CC = 5V LOW POWER DISSIPATION: I CC = 2 µa (MAX.) at T A =25 C HIGH NOISE IMMUNITY: V NIH = V NIL = 28% V CC (MIN.) POWER DOWN PROTECTION ON
LD1085CXX. 3 A low-drop, adjustable positive voltage regulator. Features. Description
3 A low-drop, adjustable positive voltage regulator Features Typical dropout 1.3 V (at 3 A) Three terminal adjustable output voltage Guaranteed output current up to 3 A Output tolerance ± 2 % at 25 C and
74V1T126CTR SINGLE BUS BUFFER (3-STATE)
SINGLE BUS BUFFER (3-STATE) HIGH SPEED: t PD = 3.6ns (TYP.) at V CC = 5V LOW POWER DISSIPATION: I CC = 1µA(MAX.) at T A =25 C COMPATIBLE WITH TTL OUTPUTS: V IH = 2V (MIN), V IL = 0.8V (MAX) POWER DOWN
Order code Temperature range Package Packaging
ST485ERB ±15 kv ESD protected, low power RS-485/RS-422 transceiver Features Low quiescent current: 300 µa Designed for RS-485 interface application - 7 V to 12 V common mode input voltage range Driver
STMUX1800L 16- to 8-bit MUX/DEMUX for gigabit Ethernet LAN switch with LED switch and enhanced ESD protection Features Description
16- to 8-bit MUX/DEMUX for gigabit Ethernet LAN switch with LED switch and enhanced ESD protection Features Low R ON : 4.0 Ω typical V CC operating range: 3.0 to 3.6 V Enhanced ESD protection: > 8 kv (contact)
PIN CONNECTION AND IEC LOGIC SYMBOLS
TRIPLE 2-CHANNEL ANALOG MULTIPLEXER/DEMULTIPLEXER LOW POWER DISSIPATION: I CC =4µA(MAX.) at T A =25 C LOGIC LEVEL TRANSLATION TO ENABLE 5V LOGIC SIGNAL TO COMMUNICATE WITH ±5V ANALOG SIGNAL LOW "ON" RESISTANCE:
STG3693. Low voltage high bandwidth Quad SPDT switch. Features. Description
Low voltage high bandwidth Quad SPDT switch Features Ultra low power dissipation: I CC = 0.2μA (Max.) at T A = 85 C Low ON resistance: R ON = 4Ω (T A = 25 C) at V CC = 3.0V Wide operating voltage range:
74VHC20 DUAL 4-INPUT NAND GATE
DUAL 4-INPUT NAND GATE HIGH SPEED: t PD = 3.3 ns (TYP.) at V CC = 5V LOW POWER DISSIPATION: I CC = 2 µa (MAX.) at T A =25 C HIGH NOISE IMMUNITY: V NIH = V NIL = 28% V CC (MIN.) POWER DOWN PROTECTION ON
74LVX05 LOW VOLTAGE CMOS HEX INVERTER (OPEN DRAIN) WITH 5V TOLERANT INPUTS
LOW VOLTAGE CMOS HEX INVERTER (OPEN DRAIN) WITH 5V TOLERANT INPUTS HIGH SPEED: t PD = 4.8ns (TYP.) at V CC = 3.3V 5V TOLERANT INPUTS INPUT VOLTAGE LEVEL: V IL =0.8V, V IH =2V at V CC =3V LOW POWER DISSIPATION:
Description. Table 1. Device summary. Order code Temp. range Package Packing Marking
Quad 2-input Schmitt NAND gate Datasheet - production data SO14 TSSOP14 Wide operating voltage range: V CC (opr) = 2 V to 6 V Pin and function compatible with 74 series 132 ESD performance HBM: 2 kv MM:
STG3699AQTR LOW VOLTAGE 0.5Ω MAX QUAD SPDT SWITCH WITH BREAK-BEFORE-MAKE FEATURE
LOW VOLTAGE 0.5Ω MAX QUAD SPDT SWITCH WITH BREAK-BEFORE-MAKE FEATURE HIGH SPEED: t PD = 1.5ns (TYP.) at V CC = 3.0V t PD = 1.5ns (TYP.) at V CC = 2.3V ULTRA LOW POWER DISSIPATION: I CC = 0.2µA (MAX.) at
54VCXH Low voltage CMOS 16-bit bus buffer (3-state non inverter) with 3.6 V tolerant inputs and outputs. Features.
Low voltage CMOS 16-bit bus buffer (3-state non inverter) with 3.6 V tolerant inputs and outputs Features 1.65 to 3.6 V inputs and outputs High speed: t PD = 3.4 ns at V CC = 3.0 to 3.6 V t PD = 3.8 ns
Order code Temperature range Package Packaging
ST75C176B ST75C176C Low power RS-485/RS-422 transceiver Features Low quiescent current: 300 ma Designed for RS-485 interface applications -7 V to 12 V common mode input voltage range Driver maintains high
SD1728 (TH430) RF & Microwave transistors HF SSB application. Features. Description. Pin connection
SD1728 (TH430) RF & Microwave transistors HF SSB application Features 13.56MHz 44V Gold metallization Common emitter P OUT = 200W with 15dB gain Description The SD1728 is a 50V epitaxial silicon NPN planar
Description. Table 1. Device summary. Order code Temp. range Package Packing Marking
9-bit parity generator Datasheet - production data Features SO14 TSSOP14 High-speed: t PD = 22 ns (typ.) at V CC = 6 V Low power dissipation: I CC = 4 μa (max.) at T A = 25 C High noise immunity: V NIH
Order codes Marking Package Packaging 2STF SOT-89 2STN2550 N2550 SOT-223. November 2008 Rev 1 1/8
2STF2550 2STN2550 Low voltage high performance PNP power transistors Preliminary Data Features Very low collector-emitter saturation voltage High current gain characteristic Fast switching speed Surface
74LCX257 LOW VOLTAGE CMOS QUAD 2 CHANNEL MULTIPLEXER WITH 5V TOLERANT INPUTS AND OUTPUTS (3-STATE)
LOW VOLTAGE CMOS QUAD 2 CHANNEL MULTIPLEXER WITH 5V TOLERANT INPUTS AND OUTPUTS (3-STATE) 5V TOLERANT INPUTS AND OUTPUTS HIGH SPEED: t PD = 6.0 ns (MAX.) at V CC = 3V POWER DOWN PROTECTION ON INPUTS AND
MC33172 MC Low power dual bipolar operational amplifiers. Features. Description
Low power dual bipolar operational amplifiers Features Good consumption/speed ratio: only 200 µa for 2.1MHz, 2V/µs Single (or dual) supply operation from +4 V to +44V (±2V to ±22V) Wide input common mode
STP16CPS05. Low voltage 16-Bit constant current LED sink driver with auto power saving. Features. Description. Order codes
Low voltage 16-Bit constant current LED sink driver with auto power saving Features Low voltage power supply down to 3V 16 constant current output channels Adjustable output current through external resistor
Obsolete Product(s) - Obsolete Product(s)
High gain Low Voltage PNP power transistor Features Very low Collector to Emitter saturation voltage D.C. Current gain, h FE >100 1.5 A continuous collector current Applications Power management in portable
STD1802T4-A. Low voltage fast-switching NPN power transistor. Features. Description. Applications
Low voltage fast-switching NPN power transistor Features This device is qualified for automotive application Very low collector to emitter saturation voltage High current gain characteristic Fast-switching
Obsolete Product(s) - Obsolete Product(s)
SINGLE POSITIVE EDGE TRIGGERED D-TYPE FLIP-FLOP HIGH SPEED: f MAX = 180MHz (TYP.) at V CC =5V LOW POWER DISSIPATION: I CC =1µA(MAX.) at T A =25 C COMPATIBLE WITH TTL OUTPUTS: V IH =2V(MIN),V IL =0.8V(MAX)
STG3820. Low voltage high bandwidth quad DPDT switch. Description. Features. Applications
Low voltage high bandwidth quad DPDT switch Description Datasheet - production data Features Flip Chip 30 (2.0 x 2.4 mm) Ultralow power dissipation I CC = 1 µa (max.) at T A = 85 C Low ON resistance R
Obsolete Product(s) - Obsolete Product(s)
Low voltage 16-Bit, constant current LED sink driver Features Low voltage power supply down to 3V 16 constant current output channels Adjustable output current through external resistor Serial data IN/parallel
Obsolete Product(s) - Obsolete Product(s) Obsolete Product(s) - Obsolete Product(s) STG3684
LOW VOLTAGE 0.5Ω MAX DUAL SPDT SWITCH WITH BREAK BEFORE MAKE FEATURE HIGH SPEED: t PD = 0.3ns (TYP.) at V CC = 3.0V t PD = 0.4ns (TYP.) at V CC = 2.3V ULTRA LOW POWER DISSIPATION: I CC = 0.2µA (MAX.) at
74VHC08 QUAD 2-INPUT AND GATE
QUAD 2-INPUT AND GATE HIGH SPEED: t PD = 4.3 ns (TYP.) at V CC = 5V LOW POWER DISSIPATION: I CC = 2 µa (MAX.) at T A =25 C HIGH NOISE IMMUNITY: V NIH = V NIL = 28% V CC (MIN.) POWER DOWN PROTECTION ON
2STN2540. Low voltage fast-switching PNP power bipolar transistor. Features. Applications. Description
2STN2540 Low voltage fast-switching PNP power bipolar transistor Features Very low collector-emitter saturation voltage High current gain characteristic Fast switching speed Surface mounting device in
Obsolete Product(s) - Obsolete Product(s)
SINGLE 2-INPUT NAND GATE 5V TOLERANT INPUTS HIGH SPEED: t PD = 4.7ns (MAX.) at V CC =3V LOW POWER DISSIPATION: I CC =1µA (MAX.)atT A =25 C POWER DOWN PROTECTION ON INPUTS AND OUTPUTS SYMMETRICAL OUTPUT
Obsolete Product(s) - Obsolete Product(s)
QUAD 2-INPUT AND GATE HIGH SPEED: t PD = 4.7 ns (TYP.) at V CC = 5V LOW POWER DISSIPATION: I CC = 2 µa (MAX.) at T A =25 C COMPATIBLE WITH TTL OUTPUTS: V IH = 2V (MIN.), V IL = 0.8V (MAX) POWER DOWN PROTECTION
LM723CN. High precision voltage regulator. Features. Description
High precision voltage regulator Features Input voltage up to 40 V Output voltage adjustable from 2 to 37 V Positive or negative supply operation Series, shunt, switching or floating operation Output current
Obsolete Product(s) - Obsolete Product(s) Obsolete Product(s) - Obsolete Product(s)
5 A low dropout fast response positive voltage regulator adjustable Features Typical dropout 1.2 V Fast transient response Three terminal adjustable Guaranteed output current up to 5 A Output tolerance
Low voltage high bandwidth dual single-pole double-throw analog switch. Description. Table 1. Device summary. Order code Package Packaging
Low voltage high bandwidth dual single-pole double-throw analog switch Applications Datasheet - production data Wearable Sport and fitness Portable equipment Features QFN10 (1.8 x 1.4 mm) Ultra low power
74V1T00CTR SINGLE 2-INPUT NAND GATE
SINGLE 2-INPUT NAND GATE HIGH SPEED: t PD = 5.0ns (TYP.) at V CC =5V LOW POWER DISSIPATION: I CC =1µA(MAX.) at T A =25 C COMPATIBLE WITH TTL OUTPUTS: V IH =2V(MIN),V IL =0.8V(MAX) POWER DOWN PROTECTION
Obsolete Product(s) - Obsolete Product(s)
SINGLE 2-INPUT NAND GATE HIGH SPEED: t PD = 5.0ns (TYP.) at V CC =5V LOW POWER DISSIPATION: I CC =1µA(MAX.) at T A =25 C COMPATIBLE WITH TTL OUTPUTS: V IH =2V(MIN),V IL =0.8V(MAX) POWER DOWN PROTECTION
LD3985xx. Ultra low drop-low noise BiCMOS voltage regulators low ESR capacitors compatible. Features. Description
Ultra low drop-low noise BiCMOS voltage regulators low ESR capacitors compatible Features Input voltage from 2.5 V to 6 V Stable with low ESR ceramic capacitors Ultra low dropout voltage (100 mv typ. at
74VHCT00ATTR QUAD 2-INPUT NAND GATE
QUAD 2-INPUT NAND GATE HIGH SPEED: t PD = 5 ns (TYP.) at V CC = 5V LOW POWER DISSIPATION: I CC = 2 µa (MAX.) at T A =25 C COMPATIBLE WITH TTL OUTPUTS: V IH = 2V (MIN.), V IL = 0.8V (MAX) POWER DOWN PROTECTION
LM323. Three-terminal 3 A adjustable voltage regulators. Features. Description
Three-terminal 3 A adjustable voltage regulators Features Output current: 3 A Internal current and thermal limiting Typical output impedance: 0.01 W Minimum input voltage: 7.5 V Power dissipation: 30 W
TS V micropower shunt voltage reference. Features. Applications. Description
2. micropower shunt voltage reference Features 2.5 typical output voltage Ultra low current consumption: 4µA typ. High precision @ 25 C ±2% (standard version) ±1% (A grade) High stability when used with
EMIF01-SMIC01F2. Single line IPAD, EMI filter including ESD protection. Features. Application. Description. Complies with the following standards
Single line IPAD, EMI filter including ESD protection Features High density capacitor 1 line low-pass-filter Lead-free package High efficiency in EMI filtering Very low PCB space consumtion Very thin package:
74LCX374 OCTAL D-TYPE FLIP FLOP NON-INVERTING (3-STATE) WITH 5V TOLERANT INPUTS AND OUTPUTS
OCTAL D-TYPE FLIP FLOP NON-INVERTING (3-STATE) WITH 5V TOLERANT INPUTS AND OUTPUTS 5V TOLERANT INPUTS AND OUTPUTS HIGH SPEED: f MAX = 150 MHz (MIN.) at V CC = 3V POWER DOWN PROTECTION ON INPUTS AND OUTPUTS
74VHC174 HEX D-TYPE FLIP FLOP WITH CLEAR
HEX D-TYPE FLIP FLOP WITH CLEAR HIGH SPEED: f MAX = 175MHz (TYP.) at V CC = 5V LOW POWER DISSIPATION: I CC = 4 µa (MAX.) at T A =25 C HIGH NOISE IMMUNITY: V NIH = V NIL = 28% V CC (MIN.) POWER DOWN PROTECTION
Obsolete Product(s) - Obsolete Product(s)
Low drop - Low supply voltage Low ESR capacitor compatible Feature summary Input voltage from 1.7 to 3.6V Ultra low dropout voltage (130mV typ. at 300mA load) Very low quiescent current (110µA typ. at
ST202EB - ST202EC ST232EB - ST232EC
ST202EB - ST202EC ST232EB - ST232EC ± 15 kv ESD protected 5 V RS-232 transceiver Features ESD protection for RS-232 I/O pins: ± 15 kv human body model Guaranteed 230 kbps date rate Guaranteed slew rate
Order codes Marking Package Packaging. STD2805T4 D2805 DPAK Tape & reel STD D2805 IPAK Tube. June 2007 Rev 1 1/9
Low voltage fast-switching PNP power transistor Preliminary Data Features Very low collector to emitter saturation voltage High current gain characteristic Fast-switching speed Surface-mounting DPAK (TO-252)
Obsolete Product(s) - Obsolete Product(s)
6 V power Schottky silicon carbide diode Features No or negligible reverse recovery Switching behavior independent of temperature Particularly suitable in PFC boost diode function Description The SiC diode
ST662AB ST662AC. DC-DC converter from 5 V to 12 V, 0.03 A for Flash memory programming supply. Features. Description
ST662AB ST662AC DC-DC converter from 5 V to 12 V, 0.03 A for Flash memory programming supply Features Output voltage: 12 V ± 5 % Supply voltage range: 4.5 V to 5.5 V Guaranteed output current up to 30
Obsolete Product(s) - Obsolete Product(s)
General features Supply voltage range: 2.6V to 5.5V 17V Maximum output voltage STCF01 Step-up converter for cell phone camera flash LEDs Two current levels up to 300mA set with external resistors Dedicated
L79xxC. Negative voltage regulators. Features. Description
Negative voltage regulators Features Output current up to 1.5 A Output voltages of -5; -8; -12; -15; -20 V Thermal overload protection Short circuit protection Output transition SOA protection Description
2N7000 2N7002. N-channel 60V - 1.8Ω A - SOT23-3L / TO-92 STripFET Power MOSFET. General features. Description. Internal schematic diagram
2N7000 2N7002 N-channel 60V - 1.8Ω - 0.35A - SOT23-3L / TO-92 STripFET Power MOSFET General features Type V DSS R DS(on) I D 2N7000 60V
BD241A BD241C. NPN power transistors. Features. Applications. Description. NPN transistors. Audio, general purpose switching and amplifier transistors
BD241A BD241C NPN power transistors Features. NPN transistors Applications Audio, general purpose switching and amplifier transistors Description The devices are manufactured in Planar technology with
Obsolete Product(s) - Obsolete Product(s)
HIGH SPEED: f MAX = 180 MHz (TYP.) at V CC = 5V LOW POWER DISSIPATION: I CC = 4 µa (MAX.) at T A =25 C HIGH NOISE IMMUNITY: V NIH = V NIL = 28% V CC (MIN.) POWER DOWN PROTECTION ON INPUTS SYMMETRICAL OUTPUT
LF253 LF353. Wide bandwidth dual JFET operational amplifiers. Features. Description
Wide bandwidth dual JFET operational amplifiers Features Low power consumption Wide common-mode (up to V CC + ) and differential voltage range Low input bias and offset current Output short-circuit protection
M74HC4052TTR DUAL 4-CHANNEL ANALOG MULTIPLEXER/DEMULTIPLEXER
DUAL 4-CHANNEL ANALOG MULTIPLEXER/DEMULTIPLEXER LOW POWER DISSIPATION: I CC = 4µA(MAX.) at T A =25 C LOGIC LEVEL TRANSLATION TO ENABLE 5V LOGIC SIGNAL TO COMMUNICATE WITH ±5V ANALOG SIGNAL LOW "ON" RESISTANCE: