Modbus I/O. RS-485 to 3-wire Universal 50W Power Supply

Transcription

1 Modbus I/O Configuration Kit Software Interface Package Model No. 900C-SIP RS- to Converter (non-isolated) Configuration Software for Windows Cable (-9) Software Interface Package This package includes Windows Configuration Software, an RS--to-485 Serial Port Converter, and an Signal Cable. These components provide everything you need to set up a Series 900 I/O module from your desktop PC before installing it on the network. RS-/485 Converter (non-isolated) to -wire Ordering Information 900C-SIP Software Interface Package. Includes Configuration Software (504-86), Non-isolated RS- to Serial Port Converter (504-4), and Cable (504-0). Items can also be ordered separately below Configuration Software for Windows (95/98/000/ME/ NT4/XP) on C-ROM Non-isolated RS- to Serial Port Converter, -9F to -9F to -wire Cable Converter, -9M to x WG Cable, 8 ft Network Power Universal 50W Power Supply The PS5R-4 is the ideal power source to drive your network. Input Power Requirement Universal power 85 to 64V C, 05 to 70V C Output 4V C,. (50W) 0-ø6.5 4-ø4.5 C ON V.J Top View (dimensions in mm) M.5 Terminal Screws Ordering Information PS5R-4 Universal Power Supply Side View (dimensions in mm) 95 usworks Modbus I/O Mounting Hardware IN-Rail Mounting For your convenience, cromag offers several mounting accessories to simplify your system installation. Our 9 rack-mount kit provides a clean solution for mounting your I/O modules and a power supply. Or you can buy precut IN rail strips for mounting on any flat surface. Ordering Information 0RM-6-IN 9" rack-mount kit with IN rail. IN RIL.0 IN RIL 6.7 IN rail strip, Type T, inches (75mm) or 6.7 inches (45mm) imensions in inches (mm). Tel: Fax: sales@acromag.com 69

2 ccessories Model US-to-Serial dapter PERSONL PUTER RUNNING WINOWS 98/ME/000/XP HOST PC RUNNING CROMG CONFIGURTION SOFTWRE HOST US TO HOST US PO 6 FEET OF CLE US MLE US SERIL CONVEER LE RS 9P Simplifies configuration of cromag I/O Modules Enables configuration via US port escription This device is a US-to-serial adapter that you can use to communicate with many cromag I/O products for setup and re-configuration for your application. Key Features & enefits Connects to I/O modules via US (other adapters may be necessary) Complete RS control signals Conforms to US Specification, Version. US-powered Cable length, 6 ft., UL approved IntelliPack 800x Series dapter and Cable INTELLIPCK SERIL PTER Performance Specifications US Specification Version. ata rate Up to 5.Kbps Environmental Standards RoHS-compliant asic Power Consumption 50m PC Requirements Windows 7 (-/64-bit) / Vista (-/64-bit) / XP (-/64-bit) / Server 00 & 008 (-/64-bit) / 000 / ME / 98SE / 98 RJ JCK (6 CONUCTOR) RJ PLUG (6 CONUCTOR) Ordering Information NOTE: For more information visit dapters US to serial adapter. Includes driver C and manual Serial port adapter. 9S connector to RJ jack to -wire cable converter and cable, -9M to x WG cable, 8 ft RS- to 5T transmitter configuration device converter and cable, 6 ft Non-isolated RS- to Serial Port Converter, -9F to -9F. Cables Cable. 6 feet long with RJ plug at each end. 9-PIN CONNECTOR (9S) MOEL MOEL (6 feet long) 900M Modbus Series dapter and Cable RS TO SERIL CONVEER (MOEL 504-4) CLE T Transmitter Series dapter and Cable TO RS 5C-SIP INTERFCE PTER cromag MOEL TOP VIEW 6 FEET OF CLE PLUG INTO TOP OF TRNSMITTER TOP VIEW Transmitter temperature of 5T plug into top cromag 5T TRNSMITTER 4 & 4 Wire 4 -T/C, mv+ + RS C 9 FEMLE 9 FEMLE 9 MLE Tel: Fax: sales@acromag.com S Wixom Rd, Wixom, MI 489 US ulletin # ll trademarks are property of their respective owners. Copyright cromag, Inc ata subject to change without notice. Printed in US 0/009.

3 468-TTM to Network Repeater GROUN C (LO) C (HI) 468-TTM-F (4VC) HOT G 468-TTM-F (0VC) L L G 468-TTM-F (5VC) L W G NETWORK CONNECTIONS SIE SIE SIE N 4V C _ SIE 4V C _ Network ccessories: 468 Series C Input T T T esigned for use with Johnson Controls N or Cnet MS/TP us PWR LEs U K RTE K K O N aud Rate Switches - - LEs For N or Cnet MS/TP bus rives up to devices Isolates and boosts signal up to 4000 ft. escription Models 468-TTM-F: 5V C Power 468-TTM-F: 0V C Power 468-TTM-F: 4V C Power cromag s network repeater device allows users to take full advantage of the standard s extended communication distances and multi-dropping capabilities. In addition, these devices offer field selectable End-of-Line Network (EOLN) terminations on both the and networks. Operation is transparent to all devices and no handshaking is required. Up to thirtytwo devices can be driven. Network repeaters are ready to mount on any base plate. Or, for a harsh environment, it can be installed in a NEM enclosure of your choice. No enclosure is necessary for use in a laboratory or office. Installation requires mounting, connecting power and cables, and setting the baud rate. pprovals UL/cUL listed: Energy management equipment Key Features & enefits esigned for use with Johnson Controls N or Cnet bus No handshaking No extra control lines I/O signal isolation aud rates of 600, 00, 400, 4800, 9600, 9.K, 8.4K, and 76.8K are switch selectable Field-selectable end-of-line network terminations on both and sides Electrical transient protection is provided. This protects the host computer from destructive noise spikes and other transient signals. LE s indicate transmission direction, bus fault conditions, and power applied. 4/5/0V C power available No separate transformer required with 4V C units (468-TTM-F) Operation Model 468-TTM-xF network repeaters isolate and boost signals allowing communication signals to travel another 4000 ft. Each repeater permits the addition of another unit load to a network. The repeater has two sides known as the and sides. The side typically connects to the network towards the host and the side connects to the extended network. Functionally, the and sides are equivalent. Repeaters receive C power through a -screw terminal strip. Transient signal protection is provided on both sides. When both lines are idle, each side is in receive mode. When a to 0 transition is detected (signifying a start bit) on either side, the opposite side s transmitter is enabled. The transmitter stays enabled for one character s time (based on the baud rate switch setting). The received character is then passed through. Tel: Fax: sales@acromag.com S Wixom Rd, Wixom, MI 489 US ulletin # c

4 T T R R R R R R Network ccessories: 468 Series - SET U RTE TO MTCH U RTE OF NETWORK. - U RTE K K NY EVICES - OPTION - OPTION - OPTION 5VC 0VC 4VC L C (HI) L C (HI) HOT W C (LO) L C (LO) G Ground G Ground Ground SEE UNIT LEL TO VERIFY REQUIREMENTS IMPONT: MOEL 468-TTM-XF UNITS ILUE INTERNL, FIEL SELECTLE EN-OF-LINE (EOL) TERMINTION RESISTORS FOHE N SIES. THESE RE ENLE VI INTERNL JUMPERS. O NOT USE EXTERNL TERMINTION WITH INTERNL EOL JUMPERS ENLE. R R R R RE LE RE LE (SIE ) acromag 4VC SIE N -N -N -N UP TO NOES PER NETWORK SEGMENT -N0 -N -N 485 > K U K RTE K R 4VC TR SIE T > OHM TERMINTION REQUIRE SET U RTE TO MTCH U RTE OF NETWORK. Tx Rx 4VC T RS-C N 4VC C INPUT C - U RTE -N REPETER MOEL 468-TTM-xF NOTE: SIE- N SIE- EOL TERMINTION JUMPERS ENLE TRNSMIT IRECTION RS-TO- N -TO-RS RE LE SET U RTE T K K RS TO CONVEER MOEL 4SCC-TTM-X - U RTE K K K acromag CONNECTION TRNSMIT IRECTION -TO- & -TO- RE LE -N RE LE (SIE ) - OPTION - OPTION 5VC 0VC L C (HI) W C (LO) L L C (HI) C (LO) G Ground G Ground GROUN RS L W 5VC L L 0VC EXTENE NETWORK -N -N4 -N5 TO HOST MOEL 4SCC-TTM-X CONVEER MOEL 468-TTM-XF REPETER SYSTEM CONNECTIONS NY EVICE OR E9 SIGNLS T CONVEER C C RX RX UP TO NOES PER NETWORK SEGMENT RS CONNECTIONS TO HOST PUTER -N RX 5 HOST PC RX S CTS SR 7 C HOST E9 0 OHM TERMINTION RESISTOR REQUIRE T EN OF NETWORK OR LST EVICE ONLY HOST 5 NOTE: JUMPERE PINS RE NULL-MOEM CONNECTIONS WHICH LLOW MUNICTION ETWEEN THE HOST N CROMG SERIES 400/400 I/O STTIONS. The system connection drawing is for general illustration purposes only. For Johnson Controls systems refer to the Metasys Network Technical Manual for N us Communication or MS/TP Communications us Technical ulletin for 468-TTM-xF wiring connections. Tel: Fax: sales@acromag.com S Wixom Rd, Wixom, MI 489 US

5 Network ccessories: 468 Series EOL JUMPERS EQUIVLENT CIRCUIT (468 UNITS ONLY) 00 OHMS Vcc JUMPER PIR (ONE SIE) EOL Jumpers Side (IN) JJ JJ EOL EOL ISLE ENLE LEs - - aud Rate Switches U - 00 RTE K 7-8.4K K LEs PWR 0 OHMS REMOVE THIS SCREW ON ECH SIE TO REMOVE COVER F 00 OHMS EOL Jumpers Side (OUT) J4J J4J EOL EOL ISLE ENLE J4J JJ FUSE G 0.5, 50V 4V C N 4V C SIE SIE NOTE: -F 4V C units do not require a separate transformer. 4V C power from the devices may be used. MOEL 468-TTM-F REPETER MOEL 468-TTM-F REPETER MOEL 468-TTM-F REPETER End-of-Line (EOL) Termination Jumper Locations. Input Power Fuse Location. SIE SIE NETWORK CONNECTIONS G G W L L L 468-TTM-F (5VC) 468-TTM-F (0VC) G HOT 468-TTM-F (4VC) C (HI) C (LO) GROUN SIE SIE R R T T 4VC N 4VC (09.) (9.98) acromag K U 7-8.4K RTE K (7.6) TYP (6.56) (7.6) TYP 7.0 (77.80).0 (5.4) Tel: Fax: sales@acromag.com S Wixom Rd, Wixom, MI 489 US

6 Network ccessories: 468 Series Specifications Communications Specifications aud Rates Switch settings on unit for 600, 00, 400, 4800, 9600, 9.K, 8.4K, and 76.8K baud rates. Switch must be in the proper baud rate position for proper operation. us Loading One unit load equivalent. us rive Complete compliance for up to unit loads ( unit loads if a repeater is used). End-of-Line Termination Network The EOLN termination network is shown on the right and is individually selected on both the and sides by a pair of shorting clips. The -side is controlled by jumper pair J, J and the -side is controlled by jumper pair J and J4. 00 Ohms 0 Ohms 00 Ohms The EOLN termination network is enabled for the side or side when the associated pair of jumpers are positioned over pins and. Conversely, the EOLN is disabled (out of the circuit) when the pair jumpers are positioned over pins and. uplex Half duplex only. ata Format Ten bits typical ( start bit, 8 data bits, and stop bit). Other formats are supported. Physical Specifications Operating Temp. Range -5 to 70 C (- to 58 F) Storage Temp. Range -5 to +85 C (- to 85 F) Relative Humidity (RH) 0 to 95% RH (noncondensing), up to 40 C (04 F). Power 468-TTM-F 5VC ±0%, 50/60 Hz, TTM-F 0VC ±0%, 50/60 Hz, TTM-F 4VC ±0%, 50/60 Hz, 0.8 typical Power Line Fuse 0.5, 5V, 0.75, G type. Isolation Provides galvanic and opto-coupler isolation between (), (), C power, and chassis ground. Common mode voltages are permitted up to 50V rms or 54V C (withstands a 500V C dielectric strength test for min. without breakdown) on a continuous basis. Complies with requirements outlined in NSI C for voltage ratings specificed. RFI Resistance Withstands an RFI field strength of 0V per meter at 7 Mhz, 5 Mhz, and 467 Mhz with no digital effect, per SM PMC.. Line Noise Effects Field and power line terminals withstand NSI/IEEE C Surge Withstanding Capability (SWC) Test with no component failures. Unit is tested to a standardized test waveform that is representative of surges (high-frequency transient electrical interference), observed in actual installations. Communications Connections Network repeater - both connectors use modular terminal blocks with screw clamps. Wire range 4 to 6 WG. Power Wire Connections Network repeater terminal block. See label on unit for power to be applied to unit. pprovals UL/cUL listed energy management equipment. Shipping Weight.0 pounds (.4 kg) packed per unit. Ordering Information to Network Repeaters 468-TTM-F 5V C Power 468-TTM-F 0V C Power 468-TTM-F 4V C Power ccessories See for more information. Tel: Fax: sales@acromag.com S Wixom Rd, Wixom, MI 489 US ll trademarks are the property of their respective owners. Copyright cromag, Inc ata subject to change without notice. Printed in US /009.