CALEC ST II BACnet MS/TP

Transcription

1 Communication description Page 2 9 CALEC ST II BACnet MS/TP Table of contents 1 General information Content Definition Registered trademark and brand names Certification according to BACnet standard Hardware Communication interface Line termination Commissioning Commissioning of CALEC ST II with the BACnet MS/TP interface BACnet Baud rate BACnet MAC address Master/slave mode Device instance number (DIN) Device object name Location Description CALEC ST II BACnet services and objects Supported BACnet services Supported BACnet objects BACnet connections, e.g. with water and oil meters Alarm PICS document Troubleshooting... 9 VD 3-125b e

2 1 General information 1.1 Content This communication description includes only specific information about CALEC ST II with the BACnet MS/TP module. Further information is available in the technical documentation of CALEC ST II. Additional documents can be found on the following website: General information about BACnet can be found at Definition BACnet is a globally accepted, open standard (ISO Standard ) in building automation. BACnet assures the inter-operability between devices of different manufacturers. CALEC ST II with BACnet MS/TP interface allows an integration in BACnet networks without using gateways. The physics of RS485 interface is used for transmission. 1.3 Registered trademark and brand names BACnet, as well as the BACnet logo are registered trademarks of ASHRAE (American Society of Heating, Refrigerating and Air-Conditioning Engineers) in Atlanta, GA (USA). 1.4 Certification according to BACnet standard CALEC ST II with the BACnet MS/TP module is certified according to the following test standards: Test standards ISO :2014 ANSI/ASHRAE Addendum ai to ANSI/ASHRAE Addendum al to ANSI/ASHRAE Addendum ar to ANSI/ASHRAE Addendum as to ANSI/ASHRAE Addendum ay to ANSI/ASHRAE Addenda an, at, au, av, aw, ax, and az to ANSI/ASHRAE ANSI/ASHRAE Addendum o to ANSI/ASHRAE BTL Test Plan 14.0 BTL Specified Tests 14.0 BTL Checklist CALEC ST II

3 2 Hardware 2.1 Communication interface INTEGRA METERING AG uses a communication interface defined by BACnet technology with twisted-pair wiring (2-core). CALEC ST II: Overview of supported functions Function Parameter Value description More information Manufacturer ID This identification is valid for INTEGRA METERING AG and Aquametro AG Data protocol BACnet MS/TP - - BACnet device profile B-ASC - - MAC address master and slave slave Factory setting: the last 2 digits of the device serial no. Master/slave setting: Changeable via CALEC ST II operating menu. Factory setting: master See: Chapter 3.4 Master/slave mode Baud rate 9600, 19200, 38400, 57600, 76800, Automatic adjustment See: Chapter 3.2 BACnet Baud rate Device instance number - The last 5 digits of the device serial no. See: Chapter 3.5 Device instance number (DIN) BACnet connection type - RS Line termination A termination resistor must be connected to both ends of the segment. The technical BACnet MS/TP specifications recommend a 120 Ohm resistor. If CALEC ST II is at the end of a segment, the internal termination resistor can be activated. Operating menu: BAcnEt TRm CALEC ST II 3

4 3 Commissioning 3.1 Commissioning of CALEC ST II with the BACnet MS/TP interface After connecting the RS-485 cable with the terminals 90a(+) and 91b(-), the following steps need to be performed: Step-by-step instructions Step Action Description 1 Configuration of CALEC ST II for use of application The respective information can be found in the operating instructions of CALEC ST II. 2 Configuration of CALEC ST II for BACnet use According to this description The relevant bus number for the configuration results from the assembly of the BACnet interface in socket # 1 or socket # BACnet Baud rate The baud rate adjustment of CALEC ST II will be set automatically after connecting the BTU meter to the network. Supported baud rates are 9600, 19200, 38400, and If the Baud rate is changed at the master system during operation, CALEC ST II needs to be restarted. 3.3 BACnet MAC address The BACnet MS/TP MAC address can be changed in the operating menu of CALEC ST II. The applicable range of the BACnet MS/TP MAC address lies between 0 and 254 (for master functionality between 0 and 127, for the slave functionality between 0 and 254). The differentiation between master and slave address range is defined via the operating menu in the menu Mod of CALEC ST II. Operating menu: BAcnEt Adr 3.4 Master/slave mode By means of the BACnet MS/TP mode selection the mode behaviour of CALEC ST II can be selected as master or slave. After 30 seconds the change is active. Operating menu: BAcnEt Mod 3.5 Device instance number (DIN) The device instance number can be changed in the operating menu of CALEC ST II. The last 5 digits of the serial number (CALEC ST II) are the factory setting for the DIN. Operating menu: BAcnEt DIN 4 CALEC ST II

5 3.6 Device object name The parameter object-name can be overwritten (standard: Calec ST II BACnet ) 3.7 Location The parameter location can be overwritten (standard: No Location set ) 3.8 Description The parameter description can be overwritten (standard: CALEC BTU METER ) 4 CALEC ST II BACnet services and objects 4.1 Supported BACnet services CALEC ST II is a BACnet Application Specific Controller (B-ASC) and supports the following services: BACnet Interoperability Building Blocks (BIBB s) Data Sharing - ReadProperty - B Data Sharing - ReadPropertyMultiple - B Data Sharing - WriteProperty - B Data Sharing WritePropertyMultiple - B Data Sharing - COV - B Device Management - Dynamic Device Binding - B Device Management - Dynamic Object Binding - B Device Management - DeviceCommunicationControl - B Device Management - TimeSynchronization - B Device Management - UTCTimeSynchronization - B Device Management - ReinitializeDevice - B DS-RP-B DS-RPM-B DS-WP-B DS-WPM-B DS-COV-B DM-DDB-B DM-DOB-B DM-DCC-B DM-TS-B DM-UTC-B DM-RD-B CALEC ST II 5

6 4.2 Supported BACnet objects CALEC ST II with BACnet MS/TP supports the following device objects and variants and their analog inputs. The analog inputs are made available according to the respective device variants. Analog inputs Object no. Designation Volume Mass Flow BDE TGR BDV DTF AI-0 Energy X X X X X X AI-1 Energy-BDE X X X X AI-2 Volume X X X X X AI-3 Volume-BDE X X X AI-4 Mass X AI-5 Auxiliary counter 1 X AI-6 Auxiliary counter 2 X X X X X X X AI-7 Auxiliary counter 3 X X X X X AI-8 Power X X X X X X AI-9 Volume flow X X X X X X AI-10 Mass flow X AI-11 Temperature warm X X X X X X AI-12 Temperature cold X X X X X X AI-13 Temperature difference X X X X X X AI-14 Density X X X X X X AI-15 Energy-TGR X Binary outputs Object no. Designation Volume Mass Flow BDE TGR BDV DTF BO-0 Relay 1 X X X X X X X BO-1 Relay 2 X X X X X X X 6 CALEC ST II

7 4.2.1 Supported BACnet units of current values CALEC ST II with BACnet MS/TP supports the following units for current values: Energy and Energy-BDE/TGR units Volume and Volume-BDE units Unit BACnet Enum Unit BACnet Enum J 16 cft 79 kj 17 m 3 80 kj/kg 125 Imp.gal. 81 MJ 126 L 82 Wh 18 US.gal. 83 kwh 19 MWh 146 BTU 20 kbtu 147 MBTU 148 thm 21 Th 22 Mass units Unit kg 39 lb 40 Tons 41 BACnet Enum Supported BACnet units of the auxiliary counters The selectable units depend on the setting of the auxiliary counter in CALEC ST II. Energy-related Volume-related Unit BACnet Enum Unit BACnet Enum J 16 cft 79 kj 17 m 3 80 kj/kg 125 Imp.gal. 81 MJ 126 L 82 Wh 18 US.gal. 83 kwh 19 MWh 146 BTU 20 kbtu 147 MBTU 148 thm 21 Th 22 Mass-related Without unit Unit BACnet Enum Unit BACnet Enum kg 39 Without unit 95 lb 40 Tons 41 CALEC ST II 7

8 4.2.3 Supported BACnet units instant values CALEC ST II with BACnet MS/TP supports the following units for instant values: Power units Volume flow units Unit BACnet Enum Unit BACnet Enum mw 132 cft/s 142 W 47 cft/min 84 kw 48 m 3 /s 85 MW 49 m 3 /min 165 BTU/h 50 m 3 /h 135 kbtu/h 157 Imp.gal./min 86 PS 51 l/s 87 RT 52 l/min 88 l/h 136 US.gal./min 89 Mass flow units Temperature units Unit BACnet Enum Unit BACnet Enum g/s 154 C 62 g/min 155 K 63 kg/s 42 F 64 kg/min 43 kg/h 44 lb/s 119 lb/min 45 lb/h 46 Tons/h 156 Temperature difference units Unit BACnet Enum K 63 8 CALEC ST II

9 5 BACnet connections, e.g. with water and oil meters There are two auxiliary inputs available to measure pulses from other meters, such as water and oil meters with pulse signals and to directly communicate the result to the BACnet MS/TP network. 6 Alarm CALEC ST II status messages are linked with the BACnet objects. INTEGRA METERING AG differs between the following types of status messages: Device status error All important device errors such as system error need to be verified including their error codes. Measurement value status alarm : Specific messages such as dt alarm have to be verified (further information can be found in the section Error messages, alarms in the operating instructions of CALEC ST II). 7 PICS document The PICS document of CALEC ST II can be found at Additional documents can be found on the following website: 8 Troubleshooting Communication errors No. Error / malfunction Possible reason Correction 1 CALEC ST II is not communicating in the BACnet MS/TP network 2 After changing the Baud rate on the master system, CALEC CALEC ST II is not communicating via BACnet MS/TP anymore Wiring of the network Terminating resistors Configuratin of CALEC ST II Configuration of BMS CALEC ST II is unable to automatically recognise the set Baud rate Check if the BACnet MS/TP devices are correctly connected. Check, if the termination and bus topology are correct. Check, if the BACnet MAC address and the device instance number are correctly configured and unique within the network Restart CALEC ST II by switching the power supply off and on again. CALEC ST II runs through an initialisation process and takes over the new Baud rate. The adapted Baud rate is displayed in Device Object in the Proprietary Property CALEC ST II 9

10 Änderungen vorbehalten / Sous réserve de modifications Modification rights reserved / Copyright INTEGRA METERING AG info@integra-metering.com * CALEC ST II