BAC-IO9 BACnet MS/TP Input / Output Modules, Wall Mounted

Transcription

1 Product sheet MOD Type BAC-IO9 BAC-IO9 BACnet MS/TP Input / Output Modules, Wall Mounted BAC-IO9 and BAC-IO9-AI have been designed to be a compact wall mounted BACnet MS/TP input and output modules. The module has 2 volt-free digital inputs for measurements e.g. for windows, occupancy sensors and so on. The module has 2 digital outputs, Vac triacs switching the plant items on/off. The IO9 modules has 2 inputs for measuring NTC0 temperature, resistive measurements (e.g. light level) or volt-free on/off signals. The IO9-AI models have 2 inputs for measuring 0..0Vdc signals. The three analogue 0..0Vdc outputs complete the compact IO-modules. With the analogue outputs it is possible to control zone valves and other modulating plant equipment. The modules support BACnet MS/TP communications with most commonly used baud rates and parity settings. The module also supports BACnet device and object discovery allowing fast and efficient programming. Model Type Model Description BAC-IO9 BACnet MS/TP Digital Input / Output Module, 2DI, 2DO, 2I, 3AO BAC-IO9-AI BACnet MS/TP Digital Input / Output Module, 2DI, 2DO, 2AI, 3AO Technical Data Power Supply Power supply Vac/dc -0%/+5% Signal Outputs Analogue Outputs 3 x 0..0V < 5mA; 00k min impedance for % accuracy Digital Outputs 2 x Vac Triacs; 2A maximum; requires Vac Power Supply Signal Inputs esistive Inputs (MOD-IO9) 2 x Universal NTC0/esistive/Digital Inputs, 0..50kOhms (NTC0/Volt-Free Digital default, configurable via SW-DCT-USB tool to resistive mode) Voltage Inputs (MOD-IO9-AI) 2 x 0..0Vdc Inputs Digital Inputs 2 x Volt-Free Contact, Impedance <KOhm Pulse Counting: Max 25Hz, Min Pulse Length 20mA (Volatile) Communication BACnet Communications Protocol BACnet MS/TP Interface S45; maximum 63 devices MAC Addressing via a bit switch; 0..7 via tool / network Communication 9k6/9k2/3k4/76k Baud; Parity /Even/Odd, or 2 Stop Bits (baud rate adjustable through bit switch) Connections Terminal Connections Solid and Stranded Cable; 55 Angle for Wiring Maximum Size: 0.05 to.5mm 2 (EN ISO) / 4 to 30 AWG (UL) ising Clamp: Size 2.5 x.9mm Environmental Conditions Operating Temperature 0 C C (..22 F) Humidity %rh (non-cond.) Storage PS SN /

2 Temperature Humidity -30 C C ( F) %rh (non-cond.) Standards CE Conformity CE Directive 2004/0/EY EN : 200 (Generic Emission) EN : 200 (Generic Immunity). Degree of Protection IP20 Housing Housing Material ABS Plastics, Self Extinguishing Mounting Wall or Junction Box Mounting, AL900 Pure White Dimensions W6 x H20 x D29mm Weight 0g Wiring Terminals Vac elay Vac elay DO DO2 Digital Output, Vac Triac Digital Output 2, Vac Triac BAC-IO9 Vac/dc 0 V G Go Vac/dc Supply Y Analogue Output, 0..0Vdc Y2 Analogue Output 2, 0..0Vdc Y3 Analogue Output 3, 0..0Vdc Go BIT SWITCH Network A+ S45 (BACnet MS/TP) B- S45 (BACnet MS/TP) Network Address Bit ate Bit ate 2 Go I DI I2 DI2 NTC0/esistive Input 0..50kOhms/Digital Input 3 (BAC-IO9) 0..0Vdc Input (BAC-IO9-AI) Digital Input, Volt-Free NTC0/esistive Input kOhms/ Digital Input 4 (BAC-IO9) 0..0Vdc Input 2 (BAC-IO9-AI) Digital Input 2, Volt-Free DO Digital Output; Vac Triac Switching to 0V; max. 2A DO2 Digital Output; Vac Triac Switching to 0V; max. 2A G Vac/dc Power Supply G0 Y 0..0Vdc Analogue Output Y2 0..0Vdc Analogue Output Y3 0..0Vdc Analogue Output G0 A+ S45 A+ Connection (BACnet) B- S45 B- Connection (BACnet) G0 I IO9: NTC0/esistive Input 0..50kOhms/Volt-Free Digital IO9-AI: 0..0Vdc DI Digital Input; Volt-Free, Max 25Hz, Min Pulse Length 20mS I2 IO9: NTC0/esistive Input 0..50kOhms/Volt-Free Digital IO9-AI: 0..0Vdc DI2 Digital Input; Volt-Free, Max 25Hz, Min Pulse Length 20mS Digital Input Pulse Counting Digital Inputs can be used for pulse counting up to 25Hz, minimum pulse length 20mS. The pulse count is stored in a dedicated register and can be read over the network. It is possible to write to this register to reset the value. PS SN.4-2/

3 Universal NTC0/ esistive/digital Inputs (BAC-IO9) Analogue Inputs (BAC-IO9-AI) Setting Up BACnet Address and Baud ate NOTE: The pulse count value is not battery backed, and therefore the network master is required to manage the data synchronisation in case of power failure. The universal inputs can be configured to operate as NCT0/Digital Volt-Free inputs or esistive Inputs. As default the inputs are configured as NTC0/Digital Volt-Free. The maximum measurement range is -0 C to 00 C (-40 F to 22 F). The NTC0/resistive configuration is changed via the Configuration Software using the USB to IO-Module cable. The digital volt-free mode is automatically activated, and a separate BACnet Binary Input objects are available to read the status. The BAC-IO9-AI has 2 x 0..0Vdc inputs. The current status can be read over the BACnet communication network. The BACnet address and the baud rate is normally set through the bit switch. It is also possible to set the address and baud rate over the configuration tool or over the BACnet communication network. NOTE: The new settings are activated automatically after approx 5 seconds if the bit switch positions have not been moved. In this case the controller reset is applied to activate the new settings. SETTING TANSMITTE BAUD ATE BAUD ATE BAUD ATE BIT SWITCH Network Address Bit ate Bit ate 2 BAUD ATE 9200 BAUD ATE 9600 / NETWOK SETTING TANSMITTE BACNET MAC ID The BACnet MAC ID is set by using bith switches BIT SWITCH to 6 using binary decoding. Each bitswitch represents the binary value and the address is set by the combination of bit switches. Few examples: Network Address Bit ate Bit ate 2 BACNET MAC ID 2 BACNET MAC ID 9 Note: When the baud rate set 9600 via the bit switch it is possible to configure the baud rate via network / tool. Note: To activate the change the transmitter requires power cycle, or software reset via the tool. Note: If all address bit switches are set, then the BACnet ID can be set over the BACnet or through configuration tool. BACnet Interoperability Building Blocks Supported (Annex K) Application Service Initiate Execute BIBB eadproperty Yes DS-P-B eadpropertymultiple Yes DS-PM-B WriteProperty Yes DS-WP-B einitializedevice Yes Who-Is Yes DM-DDB-B I-Am Yes Who-Has Yes DM-DOB-B I-Have Yes DeviceCommunicationControl Yes DM-DCC-B BACnet Standard Types Supported No dynamic Creation or Deletion supported. s, and object instances, are assigned to fixed f unctions within the proprietary control application of the product as follows: Number Of Instance Assignments Instances Device Analog Input 7 AI(0) Not Assigned AI() Not Assigned AI(2) Not Assigned AI(3) NTC0/I/AI AI(4) NTC0/I2/AI2 AI(5) Not Assigned AI(6) Not Assigned Analog Outputs 3 AO(0) Y Output AO() Y2 Output AO(2) Y3 Output Analogue Value 6 AV(0) Not Assigned AV() Not Assigned AV(2) Not Assigned AV(3) Not Assigned AV(4) DI Pulse Count AV(5) DI2 Pulse Count PS SN.4-3/

4 Number Of Instances Instance Assignments Binary Input 3 BI(0) DI input BI() DI2 Input BI(2) Not Assigned BI(3) Not Assigned BI(4) Not Assigned BI(5) Not Assigned BI(6) Not Assigned BI(7) DI3 input (Universal I Input) - BAC-IO9 BI() DI4 Input (Universal I2 Input) - BAC-IO9 Binary Output 2 BO(0) DO Output BO() DO2 Output Device (equired ) Property Name /ID Attributes ange Default Identifier /W MAC_Address Name /W Characters Max Concatenation of product type and MAC address i.e. "BIO_00" Type System Status STATUS_OPEATIAL Vensor Name SyxthSense Vendor Indetifier 65 Model Name UD Protocol Version Protocol evision 0 Max APDU Length 40 Segmentation Support No APDU Timeout 3000 ms Number APDu etries 3 MaxMaster 27 Max_Info_Frames Database evision 0 PS SN.4-4/

5 Analogue Input s equired Property Name /ID Attributes ange Default Identifier Name AI(0) Not Assigned AI() Not Assigned AI(2) Not Assigned AI(3) NTC0 / I/ AI AI(4) NTC0 / I2/ AI2 AI(5) Not Assigned AI(6) Not Assigned Type 0 Present Value /W AI(0): Not Assigned AI(): Not Assigned AI(2): Not Assigned AI(3): AI(4): AI(5): Not Assigned AI(6): Not Assigned Status Flag Out-Of-Service /W FALSE Units AI(0): Not Assigned AI(): Not Assigned AI(2): Not Assigned AI(3): UNITS_OHMS AI(4): UNITS_OHMS AI(5): Not Assigned AI(6): Not Assigned Analogue Output s equired Property Name /ID Attributes ange Default Identifier Name AO(0) = Y AO() = Y2 AO(2) = Y3 Type Present Value /W Status Flag Out-Of-Service /W FALSE Units UNITS_PECENT PS SN.4-5/

6 Analogue Value s equired Property Name /ID Attributes ange Default Identifier Name AV(0) Not Assigned AV() Not Assigned AV(2) Not Assigned AV(3) Not Assigned AV(4) - DI Pulse Count AV(5) - DI2 Pulse Count Type 2 Present Value /W Status Flag Out-Of-Service /W FALSE Units AV(4) = NO_UNITS AV(5) = NO_UNITS Priority Array elinquish Default /W AV(0) = Not Assigned AV() = Not Assigned AV(2) = Not Assigned AV(3) = Not Assigned AV(4) = 0 AV(5) = 0 Binary Input s equired Property Name /ID Attributes ange Default Identifier Name BI(0) = DI BI() = DI2 BI(2) = Not Assigned BI(3) = Not Assigned BI(4) = Not Assigned BI(5) = Not Assigned BI(6) = Not Assigned BI(7) = DI3 (I) - BAC-IO9 BI() = DI4 (I2) - BAC-IO9 Type 3 Present Value /W 0.. Status Flags Out-Of-Service /W FALSE Polarity /W POLAITY_NOMAL Active Text "on" Inactive Text "off" PS SN.4-6/

7 Binary Output s equired Property Name /ID Attributes ange Default Identifier Name BO(0) = DO BO() = DO2 Type 4 Present Value /W 0.. Status Flags Out-Of-Service /W FALSE Polarity /W POLAITY_NOMAL Priority Array elinquish Default /W BINAY_INACTIVE Active Text "on" Inactive Text "off" Types No dynamic Creation or Deletion supported App_Config Application Configuration Number Of Instances Instance Assignments Provides a container for all the proprietary application specific properties. equired Property Name /ID Attributes ange Default Identifier MAC_Address Name "App_Config" Type 2 Property ID Description BACnet Data Type ange 3000 Firmware Unsigned ead Only Version MAC Address Unsigned Baud ate Unsigned 0 = 9600 (Default) = = = Hold On Delay Setting for Digital Input Unsigned Seconds (Default 0s) 4006 Hold On Delay Setting for Digital Input 2 Unsigned Seconds (Default 0s) 4000 Force eset Unsigned 0 = Normal = Force eset 400 Non Volatile Memory Update 4003 Force Factory Defaults Unsigned Unsigned 0 = Normal = Update 0 = Normal = Force Defaults PS SN.4-7/

8 4004 Force 0..0V Output Calibration outine Unsigned 0 = Normal = Force Calibration Dimensions Wall Box Screw Hole Locations PS SN.4 - /