INSTALLATION INSTRUCTION 96A. BOSCH DP6000 Generation IV VHF -UHF FM Paging Receivers LBB 609x/xx - LBB 619x/xx. Security Systems

Transcription

1 INSTALLATION INSTRUCTION 96A en October 23. Page BOSCH DP6 Generation IV VHF -UHF FM Paging Receivers LBB 69x/xx - LBB 69x/xx Table of contents Page Introduction... Type Numbers... 3 Power supply... 4 Receiver built-in functions... 5 User Switch Tables... 5 Programmable Slide Switch Configurations... 7 Installer Monitor and Test s... 2 Installer Programming INTRODUCTION Intended for use in a Bosch DP6 Digital paging system, the Generation IV range of receivers are fully compatible with the existing and former range of Generation I, II, III receivers and transceivers. This extensive range of receivers gives a wide choice of functions to cover the majority of specific paging requirements. The receivers provide the following depending on the type number: To give an LED indication when paged. To bleep, vibrate or both when paged. To receive spoken messages when paged. To receive and manage displayed numeric or alphanumeric messages. To generate an absent signal when placed in a storage/charging rack. Security Systems

2 Octobery 23. Page 2 Front view Rear view A B (see section 4) Bosch C Low battery indication Out-of range indicator Programming mode Decimal Group call enabled Bleep OFF/SOFT/LOUD Speech OFF/ON Telemetry message indicator Message No. Message scroll (> 24 characters) D E F (see section 3.) G Side view Battery placement/utility switch Top view M H (see section 4.) Bottom view L N Programming dependent (see section 4.) 2 3 J K CHARACTER SET FOR ALPHA DISPLAY II I 2 x LR (see section 3.) O P 2 3 Programming (see section 3 & 4) Disposable batteries Rechargeable batteries * 2* Key to Symbols A Vibrator (not applicable for EX intrinsic versions) B Alphanumeric display with back-lighting C Icon bar on display (user operation) D Clip attachment (pocket) E Battery cover lock (slide to open) F Battery compartment G Label placement H 5-digit numeric display J Battery cover locking screw (EX versions only) K Charging/programming/absent contacts L LED indicator M RESET/RECALL/DELETE button N User switch (3-position) O Battery placement (see section 3.) P Utility 3-position sliding switch FIGURE. Layout Generation IV receivers (illustrated version type LBB 6x94/xx)

3 DP 6 DIGITAL PAGING SYSTEM October 23. Page 3 2. TYPE NUMBERS This Installation Instruction covers the following type numbers (see Table ): Type Number Description Colour LBB 69/xx UHF - FM bleep/numeric Light LBB 692/xx UHF - FM bleep/speech/numeric/vibrator Light LBB 693/xx UHF - FM bleep/numeric/alphanumeric Light LBB 694/xx UHF - FM bleep/speech/numeric/alphanumeric/vibrator Light LBB 696/xx UHF - FM bleep/numeric Dark LBB 697/xx UHF - FM bleep/speech/numeric/vibrator Dark LBB 698/xx UHF - FM bleep/numeric/alphanumeric Dark LBB 699/xx UHF - FM bleep/speech/numeric/alphanumeric/vibrator Dark LBB 69/xx VHF - FM bleep/numeric Light LBB 692/xx VHF - FM bleep/speech/numeric/vibrator Light LBB 693/xx VHF - FM bleep/numeric/alphanumeric Light LBB 694/xx VHF - FM bleep/speech/numeric/alphanumeric/vibrator Light LBB 696/xx VHF - FM bleep/numeric Dark LBB 697/xx VHF - FM bleep/speech/numeric/vibrator Dark LBB 698/xx VHF - FM bleep/numeric/alphanumeric Dark LBB 699/xx VHF - FM bleep/speech/numeric/alphanumeric/vibrator Dark ACCESSORIES LBB 534/5 Leather pouch for belt attachment n/a LBB 593/2 Rechargeable NiCAD batteries (set of 2) n/a LBB 593/28 Rechargeable NiMH batteries (set of 28) n/a NOTE: For ATEX approval please refer to Installation Instruction No. 96B. /xx denotes the selected frequency of the receiver and its EX approval. All receivers are available in EX-versions (class Eex ib IIc T6). EX versions have no vibrator functions. Light colours = Dark mushroom Dark colours= Charcoal

4 Octobery 23. Page 4 3. POWER SUPPLY INTRODUCTION The power to the receivers is supplied by two LRI sized rechargeable or non-rechargeable batteries (figure. (O)) or by a single 3 V (non-rechargeable) lithium type Sanyo CR26 SE battery. The choice between rechargeable and non-rechargeable batteries is made by a 3-position switch located inside the receivers battery compartment (figure. (P)). See Battery placement. WARNING: Never charge non-rechargeable batteries. Always place the programming switch in the middle position (2) (figure. (P)) for this type of batteries. Never leave dead batteries in the receiver RECOMMENDED BATTERY TYPES Rechargeable: LR NiCAD (LBB 593/2) or LR NiMH (LBB 593/28) or batteries with an identical specification. Non-rechargeable batteries: LR Alkaline or batteries with an identical specification. NOTE: When placed in a Bosch storage or charging rack type LBB 65/, /, /2 or LBB 652/ (single storage rack) the receiver is powered from the charging/storage rack and not from the batteries. REPLACEMENT 2 x LR. Opening the battery cover To open the battery cover, slide the battery cover lock (figure. (E)) in the direction of the clip. Use the special tool (EX versions only) delivered with the receiver to unscrew the locking screw (figure. (J)) located underneath the battery cover. Slide the battery cover (figure.(f)) downwards Remove the battery(s) 2. Battery type selection Remove the battery(s) (figure.(o)) Locate the 3-position utility slide switch inside the battery housing (figure.(p)). Upper Position = Programming/diagnostics mode only Middle Position 2 = Non rechargeable disposable batteries Lower Position 3 = Rechargeable batteries 3. Battery replacement Place the new battery(s) in the correct position (figure.(o)) If rechargeable batteries are used ensure the batteries are fully charged before using the receiver. Close and lock the battery cover. 2 3 Utility switch When discarding batteries follow local regulations for disposal instructions.

5 Octobery 23. Page 5 BATTERY CHARGING CONTACTS Charging contacts The receiver has three contacts (figure.(k)) used for charging and programming the receiver when placed in its charging/storage rack. One contact also provides Absent indication via the DP6 encoder(s). The charging current is approx. ma. While the receiver is in the storage rack, new messages will be stored in the memory stack. When taken out of the rack it will emit two attention bleeps to indicate to the user that new messages have been received. 4. RECEIVER BUILT-IN FUNCTIONS The following functions are available depending on the receiver type number. INTRODUCTION ADDRESSES Description Depending on the type number, the receivers provide the following basic functions:. To give an LED indication when paged. 2. To bleep, vibrate or both when paged. 3. To receive spoken messages when paged. 4. To receive and manage displayed numeric and/or alphanumeric messages. 5. To generate an absent signal if placed in a storage/charging rack. Each receiver has 8 addresses: normal, 5 group (fixed or dynamic), ALL-call (CCCC) and telemetry/normal address. All addresses with the exception of the ALLcall address can be included in a decimal group call. The installer can disable the ALLcall, telemetry and decimal group addresses (opcode ). Address = telemetry or normal call address (depending on opcode setting) Address = normal call address Address 2-6 = group call address Address CCCC = all call address (enable/disable by opcode setting) Address xfff = decimal group call addresses Addresses can be programmed for 4 or 7-digits (opcode S). In stand-by mode, the numeric display can display 4 address digits (max.). For receivers programmed with 7- digit addresses, the least significant digits only are displayed. If the telemetry address is not used (opcode, disabled) it can be used as an extra individual call address. See Telemetry function. The receiver can be programmed (opcode U) to display (during stand-by mode) its normal address on both the numeric and alphanumeric display. The installer can also determine the number of address digits to be displayed (opcode 2R). If 7-digit addresses are used the numeric display shows max. 4 least significant digits of the address. USER NAME The receiver can be programmed to incorporate a user name (e.g. John Smith) for alphanumeric display versions only. Once programmed the user name is displayed together with its address on the alphanumeric display (see section 6. Programming User Name) JOHN SMITH

6 Octobery 23. Page 6 SYSTEM IDENTITY NORMAL CALL (including speech) Description System Identity The System identity (range HEX - HEX 3) is transmitted with the mode word in the DP6 code to separate two neighbouring systems which are operated on the same frequency. This feature can only be used in systems where this function has been implemented in the central desk. The system ID digit (opcode Q ) at present should be set to. This value is of no importance to the programming calls. Normal calls are calls addressed to a receiver with an assigned address. A Normal call to a receiver can include coded messages with different bleep patterns, vibration and/or light signals, or messages on a numeric and/or alpha-numeric display. One way speech messages are also possible between an encoder and the paging receiver. Normal calls therefore can comprise: Bleep/vibration/LED indication with 5-digit (-digit information is possible) and 24- character alphanumeric information (48-character messages are also possible). All calls can be accompanied with speech messages. GROUP CALL Paging call to a group of paging receivers (programmable) by Group call (fixed or dynamic) (e.g. 2222), or decimal group call (e.g where receiver 2 to 2999 are called). When the receiver is called by one of its group call addresses, it will emit a cricketed bleep tone corresponding to the number being entered (e.g. when entering bleep code No.3, the bleep pattern will be is call tone B (see Bleep Vibrator patterns)). The receiver will not generate an absence signal when housed in its storage rack and when called by one of its group call addresses. The programmable group call addresses (2-6) in the receiver can be fixed or dynamic. The address is fixed if, via address programming (see section 5.) an address has been programmed in one of the group call addresses. If the group call address is not programmed and contains address [CCC]CCCC, this address can be used as a dynamic group call address. The dynamic group call function enables the system to include or remove a pager holder from a specified group of pager holders, without having to put the receiver into the programming mode. This function is done by transmitting special calls and can be used for special applications to create flexible groups within a system (e.g different shift working patterns). To remove the dynamic group addresses proceed as follows: - placing the receiver in a rack (this function can be enabled/disabled (Opcode R). - switching the receiver OFF and ON again. - via a special call from a system encoder (e.g. alpha desk) It is also possible to program the receivers addresses to 6 (enabled/disabled by opcode setting and/or 3-position user switch) to respond to a decimal group call. The - key on the desk can then be used to call a group of receivers as follows: If the character - is entered in place of a call number digit, this will replace all numbers - 9 in that call number location. In 4-digit addresses, the character - can be entered in place of any of the last three digits of the call number. In 7-digit addresses, the character - can be entered in place of any of the last 6-digits.

7 DP 6 DIGITAL PAGING SYSTEM October 23. Page 7 Description GROUP CALL (contd.) Assuming that no call number digits have been pre-programmed in the desk and all 4 call number digits must be keyed in. A decimal group call can therefore be transmitted as follows: Key in - - -calls receiver numbers to 999 Key in 4 - -calls receiver numbers4 to 499 Key in 59 -calls receiver numbers59 to 599 Bearing in mind that all digits apart from the - are variable between and 9, you can see that any selected group of, or receivers can be called as a decimal group call. This must be born in mind when the installer is allocating receiver addresses and enabling or disabling the decimal group call facility. ALL-CALL TELEMETRY CALL DISPLAY MESSAGES NUMERIC DISPLAY 5-digit display This address is not programmable and is the same for all receivers in the system and it would normally be used in an emergency situation where every receiver holder would have to respond to a single call (The fixed value for this address is CCCC ). This call will be received even if the receiver is programmed for don t disturb The receiver will always enter the speech mode after an All Call. The use of this call can be enabled or disabled by programming (opcode S). Paging calls with telemetry information to a specific telemetry address. The message is stored in a specific location in the stack. Messages may consist of 5-digit numeric information, a 24 character alphanumeric message or both. The receiver will automatically show the message in the relevant display. If a message contains only a 5-digit numeric info the alphanumeric display will also display this information. If a call is received without 5-digit numeric information, the numeric display will show ( ). The Numeric display can display the receiver s address or 5-digit numeric information accompanying a paging call. A -digit numeric message can also accompany a paging call (i.e 2 x 5-digit messages are transmitted). In this case the message will be converted for display on the alphanumeric display (the numeric display shows ). For versions with numeric display only, the user should use the RESET/RECALL button to scroll the remainder of the message (see Message handling). If a receiver is paged without numeric information the displays shows: NOTE: The receiver can be programmed (opcode U) to display (during standby) its address or the last received information before or during standby.

8 Octobery 23. Page 8 ALPHANUMERIC DISPLAY Description The 24-character LC-display with back-lighting (see back-lighting) is intended for the following:. Displaying alphanumeric messages accompanying paging calls. A 48-character alphanumeric message can also accompany a paging call (i.e 2 x 24-character messages are transmitted). In this case the user should use the RESET/RECALL button to scroll the remainder of the message (see Message handling). 2. Displaying telemetry messages (if enabled via opcode T) (see Telemetry function) Alphanumeric 24-character display 3. To view opcodes and address (See viewing addresses and opcodes) 4. Display own address and user name Back-lighting Back-lighting for the alphanumeric display is incorporated for use in badly lit situations. If enabled for back-lighting (opcode U) the display will illuminate with every incoming call containing alphanumeric information and when scrolling through the message stack. The light will switch OFF approx. 8 seconds after the bleep or after seconds if the RESET/RECALL button has not been pressed again. VIEWING ADDRESSES AND OPCODES LED INDICATION To view the receiver s address and opcodes while the receiver is in its normal operation mode proceed as follows:. Remove the receiver from its rack or switch the receiver ON while keeping the RESET/RECALL button pressed. Both the receiver displays show the firmware/ release version. 2. Using the RESET/RECALL button the following can be viewed in order: - addresses - 6 (in the numeric display 7-digit addresses are shown as follows: alternating ( AA 6 A 5 A 4 to A 3 A 2 A A ) - opcodes and 2 (in the numeric display, only the last 5 opcode digits are shown (digit of opcode and 2 are not used)) - user name (receivers with alpha display only) 3. If no button is pressed within seconds the receiver automatically returns to it normal standby mode. The LED indicator (figure L) indicates an incoming call. The LED flashes during the bleep and for 8 seconds after the bleep. If the receiver is set to bleep/vibrate until RESET the LED will flash according to the same pattern until a RESET is given (max. 255 seconds). See also Bleep/Vibration patterns. LED indicator BLEEP/VIBRATOR PATTERNS Bleep/vibration patterns The following bleep patterns/bleeps are available:. Normal call patterns 2. Alert bleeps 3. Error bleeps 4. Out-of-range bleep 5. Low battery bleep 6. Shut-down bleep 7. Programming bleep

9 DP 6 DIGITAL PAGING SYSTEM October 23. Page 9 NORMAL CALL BLEEP PATTERNS Bleep LOUD Bleep SOFT No ICON = SILENT bleep The receiver can be called with 4 different bleep/vibration patterns (7 normal patterns and 7 cricketed patterns) or with a silent call. In vibrator types the cricketed pattern is treated as a normal pattern. Each bleep pattern is assigned a codinf (code information) digit for use in accompanying NORMAL calls ( - 4). The bleep tone can be enabled or disabled depending on the opcode programming (opcode 2U). When a call is made to a GROUP call address the receiver will always bleep with a cricketed tone. Bleep tones/vibration can be stopped by pressing the RESET/RECALL button, or on time-out. If a second call is received while the receiver is still bleeping the bleep will cease and the new incoming bleep will takeover. The volume of the bleep tones can be set by the installer (opcode 2U), its volume level indication shown in the Icon bar on the display (C(E)). Normal call bleep patterns /8 /9 Description 2/A 3/B 4/C 5/D 6/E 7/F Silent call Bleep pattern - 6 = normal tone Bleep pattern 8 - E = cricketed tone The levels of the above bleep patterns are dependent on the OPCODE set and the 3- position user switch (see 3-position user switch). During an urgent call or a call with manual request, the bleep volume will always be loud.

10 Octobery 23. Page ATTENTION BLEEP Description Attention bleep The attention bleep is emitted to alert the attention of the user. The bleep and LED patterns are shown below: Soft bleep 8 x 33 msec. LED The user is alerted with this pattern under the following conditions:. Switching the receiver ON/OFF 2. When set to silent bleep and a call is received 3. Placing and removing the receiver from its charging/storage rack 4. Change of user switch position 5. Acknowledge when deleting messages. 6. Reaching end of message stack when scrolling 7. Bring receiver back-in range when taken out-of-range (see out-of-range bleep) 8. Depending on the bleep pattern digit of the programming call for a dynamic group call address the attention bleep can be generated (bleep pattern digit does not equal F) When a receiver is removed from its storage rack and it has received new messages while in the rack, the receiver will emit a second attention bleep after the out-of-rack bleep. OUT-OF-RANGE DETECTION Out-of-range icon (figure C(B)) Out-of-range bleep The out-of-range bleep (programmable opcode U) is emitted when the receiver has been detected as out-of-range (see Out-of-range). See pattern and description below: 8 x 33 msec. until reset soft bleep Description Out-of-range All receivers incorporate an Out-of range function to alert the user when the receiver has been taken out-of-range of the system transmitters. An encoder in the DP6 system transmits an out-of-range signal every 3 seconds, if a receiver fails to receive any valid DP6 call within approx. 6 seconds, it will generate the out-of-range bleep to the receiver/user. Out-of-range is indicated as follows:. The receiver emits a bleep signal until RESET by the user. The bleep until RESET function is used with a time-out of 62.5 seconds. 2. Visual display: Alphanumeric display show out-of-range icon. Numeric display only version: shows ( - - ) alternating with (- - -). To RESET the receiver in Out-of-range state proceed as follows:. Bring the receiver back into range of the DP6 system transmitters. 2. If not brought back-in range within 3 minutes the receiver switches OFF automatically after first emitting a loud continuous warning bleep (approx second). Once the receiver has been automatically switched OFF, it can be switched ON by placing the 3-position switch to ON from OFF or by placing the receiver into its charging/storage rack (except single storage rack LBB 652/).

11 DP 6 DIGITAL PAGING SYSTEM October 23. Page LOW BATTERY Low battery icon (figure C(A)) BATTERY SAVING ERROR BLEEP Description Low battery bleep In low battery state (programmable opcode U) the following bleep pattern is emitted: x 8 x 33 msec. soft bleep : The receiver in low battery state will give an audible (low volume bleep) every 255 seconds and/or display warning by the low battery icon which will be on constantly during low battery state. In this state the batteries must be replaced or the receiver must be placed in its charging/storage rack. The low battery state warning bleep can be disabled/enabled via opcode programming (see programming opcodes). The display warning is dependent on the type of receiver (i.e alphanumeric display). In the alphanumeric display the Low battery icon is ON and the numeric display flashes. After hour of low battery the receiver switches off automatically after first emitting the shut-down bleep. In battery saving mode (programmable opcode S (5F-string)), the HF section of the receiver is switched ON/OFF periodically to reduce receiver current consumption. A preamble string is transmitted before each call to switch the HF section ON before a call is transmitted. The HF section remains ON for a set time to ensure that a second call is not missed. Error bleep The receiver emits an error bleep to indicate user input error. See pattern below: 8 x 33 msec. x soft bleep Error bleep: to indicate user input error (e.g. if the user tries to delete messages while this function is disabled by the installer). SHUTDOWN BLEEP Shutdown bleep The shut-down bleep is emitted when the receiver switches itself OFF automatically. See pattern below: x 8 x 33 msec. loud bleep The shut-down bleep is emitted after 3 seconds of continuous out-of-range or after hour of continuous low battery. BLEEP UNTIL RESET Reset/Recall button Bleep until RESET The receiver can be set by the installer to bleep until RESET (i.e the receiver bleeps until the RESET button is pressed. If a RESET is not given within 6 seconds the bleep pattern will be repeated after 3 seconds of silence. The procedure will be repeated until RESET for a maximum period of 255 seconds. When the receiver is called with an urgent call or with a call with a manual request (these functions are determined by the modeword in the DP6 call string) the receiver will respond with a bleep until reset independent of the opcode setting.

12 Octobery 23. Page 2 VIBRATOR MESSAGE HANDLING Stack number of message being viewed Press the RECALL button to view the remaining part of the alphanumeric message Description Vibrator call patterns Receiver types with vibrator are able to vibrate in unison with 7 different patterns (depending on codinf ). Cricketed vibration patterns are identical to the normal vibration patterns. Message handling (numeric and alphanumeric) Each call to a receiver can contain 5-digit numeric and/or max. 48-character alphanumeric messages (see Numeric and alphanumeric display). The receiver contains a memory stack for messages and telemetry information (see Telemetry function). The number of messages stored in the message stack is + Telemetry message (if enabled). The memory stacks operate in a First-In-First-Out (FIFO) basis. If two identical messages/information are sent to a receiver, the last message only will remain in the stack. Dependent on the modeword of the paging call, messages will be stored or not stored in the message stack. The receiver can also handle 48 character messages which are sent as two calls (first call sent with codinf F) within 4 seconds. These two parts are then combined as a single message. In the display this is indicated with the icon blinking if the first 24 characters of the message are displayed and with the icon ( fig.c (J)) if the second 24 characters are displayed. If the message is not meant for storage in the stack it will be displayed until the RECALL button is pressed (depending on standby setting).when the receiver is programmed to display its own address during standby this message remains in the display until timeout (8 seconds after the bleep has ended). Such a message will not have an index number (i.e MESSAGE NUMBER icon blank). If a message contains both numeric and alphanumeric information while scrolling, the receiver gives a short flash of the LED to indicate that the message also contains alphanumeric information. Messages in the memory stack can be recalled/scrolled and deleted using the RESET/RECALL/DELETE button (figure M). REMARK: The DP6 callstring can contain the following sections:. address (5-digit HEX) (receiver call number) 2. Numeric information (5-digit HEX) displayed on the 5-digit numeric LC-display 3. Mode word (5-digit HEX) (function control) 4. Alphanumeric message displayed on the 24-character alphanumeric LC-display RECALLING/SCROLLING MESSAGES The Message handling icon indicates the stack number of the message being viewed.. To view the messages from the message stack, press the RECALL/RESET button to scroll. If back-lighting is enabled the RECALL/RESET button should be pressed twice to start scrolling (the first press switches the back-light ON). 2. A bleep is emitted when the end of the message stack is reached. If the button is not pressed for approx. 8 seconds the receiver returns to its standby mode displaying the last stored message (or if set the receiver s address).

13 DP 6 DIGITAL PAGING SYSTEM October 23. Page 3 MESSAGE HANDLING (contd.) Description DELETING MESSAGES IN STACK Deleting messages from the stack is an installer option (opcode 2T). If enabled messages can be deleted as follows:. Scroll using the RESET/RECALL button until the message to be deleted is displayed. Once displayed, press the RESET/RECALL button again for approx. 3 seconds to delete the displayed message. An alert bleep indicates the message has been deleted. DELETING ALL MESSAGES IN STACK Deleting ALL messages in the stack is an installer option (opcode 2T). If enabled ALL messages will be deleted as follows:. When the receiver is placed in the storage rack. 2. When the receiver is switched OFF NOTE: While the receiver is in the storage rack, new messages will be stored in the memory stack. When taken out of the rack it will emit two attention bleeps to indicate to the user that new messages have been received. ERRORS IN MESSAGES ERROR IN MESSAGE DETECTION The receiver can be programmed (opcode T) to accept or reject errors in alphanumeric or numeric messages. For versions with alphanumeric displays a max. of 3 errors in a message can be accepted (characters with errors are displayed as checkboard signs ) or rejected. Calls without numeric info are either accepted or rejected (programmable opcode T). REMARK: In older DP6 systems, encoders may be present, where the DP6 callstring consists of the receiver address only (i.e. IPA coupler LBB 594/3). For use of these receivers in these systems, calls without info should be accepted. TELEMETRY FUNCTION The telemetry function (Mailbox) is only available for version with alphanumeric display. This function is intended to provide users with continuous up-to-date information (e.g process control (max. 48-character)). To receive telemetry information the receiver must be programmed for a telemetry address (see addresses). If the telemetry function is enabled one memory stack place (first level) is reserved for receiving this message (address is used as the telemetry address). The user can be alerted or not alerted depending on the bleep pattern digit (codinf) of the telemetry call. If the telemetry call is sent as a silent call (codinf F ) the message is written directly to the top level of the message stack and not to the display. The user is informed by a flashing telemetry icon. To view the message press the RESET/RECALL button. If the telemetry call includes a bleep pattern ( HEX - HEX E) the message is written to the top level of the memory stack and also to the alphanumeric display. The telemetry icon is ON. Depending on the standby setting (opcode U) this message remains in the display or it will return to displaying the normal receiver address. The telemetry icon will be permanently ON while the telemetry message is in the display. The telemetry function can be enabled or disabled (opcode T).

14 Octobery 23. Page 4 SPEECH FUNCTION Description Speech (applicable for LBB 6X92, 6X94, 6X97 and 6x99 only) The functions that can be programmed for speech can be set in opcode 2. If always speech after a call is enabled (opcode 2T) the receiver will switch to speech after every call that doesn t have a mode word. If the call is sent with a mode word, the speech setting of the mode word has priority over this function. Speech coupled to codeinf (6 or 7) (opcode 2T) enables the receiver being switched to speech by calls without mode word depending on the bleep pattern digit. If the codeinf digit is 6 or 7 and this function is enabled the receiver will automatically switch to speech. If the call is sent with a mode word, the speech setting of the mode word has priority over this function. Maximum speech time can be set using opcode 2S (range to 4 seconds or infinite). Normally speech is reset by a speech reset call from the encoder. The speech icon in alphanumeric speech receivers will be visible if the programmed speech time does not equal. 3-POSITION USER SWITCH The function of the 3-position user switch (figure N) is programming dependent (opcode and 2) and dependent on the type of receiver (with or without vibrator). A combination of the following functions can be programmed:. Switch the receiver ON/OFF 2. Switch the volume of the bleep between silent, soft and loud 3. Enable/disable decimal group calls for this receiver User switch Table 3 shows the switch functions depending on the opcode settings (opcode T decimal group call enabled/disabled and opcode 2U user switch group or alert). Table 4. shows the functions for position of the 3-position user switch depending on the opcode setting S (power OFF enabled/disabled and if the receiver includes a vibrator). Bleep volume icon (figure C(E)) Table 5 and 6 shows the function for position I and II of the 3-position switch depending on the opcode setting 2U (bleep volume and user switch functions (group or alert)) and if the receiver includes a vibrator. See 5. USER SWITCH FUNCTION TABLES: NOTE: Fill-in the customer specific programming of the 3-position user switch in the user manual. Decimal group call icon (figure C(D))

15 DP 6 DIGITAL PAGING SYSTEM October 23. Page 5 5. USER SWITCH FUNCTION TABLES OPCODE Decimal group call (enable/disable) Opcode T Switch function setting (group or alert) Opcode 2U decimal group disabled (opcode bit = ) X (don t care) Alert decimal group enabled (opcode bit = ) (bleep) Alert decimal group enabled (opcode bit = ) (group) Group Switch function (pos. I & II) Opcode S Power OFF (enable/disable) Bleep volume Receiver without vibrator (Switch pos. ) disabled < >* silent bleep vibrator Receiver with vibrator (Switch pos. ) disabled * soft bleep vibrator + soft bleep enabled x (don t care) receiver OFF receiver OFF *bleep volume : = don t disturb is not possible, the receiver will always bleep. SWITCH POSITION I and II (OPCODE T and 2U) ( Switch set to ALERT) Switch OPCODE Receiver without vibrator Receiver with vibrator T Decimal group 2U Bleep Volume ALERT grp = disabled alert = silent ALERT grp = disabled alert = silent ALERT grp = disabled alert = soft ALERT grp = disabled alert = loud ALERT alert = silent ALERT alert = silent ALERT alert = soft ALERT alert = loud Position I Position II Position I Position II grp =disabled alert = soft grp = disabled alert = loud grp = disabled alert = loud grp = disabled alert = loud alert = soft alert = loud alert = loud alert = loud grp = disabled alert = vib grp = disabled alert = vib grp = disabled alert = vib grp = disabled alert =vib + loud alert = vib alert = vib alert = vib alert = vib + loud grp = vib alert = silent grp = disabled alert = soft grp = disabled alert = loud grp = disabled alert = vib + loud alert = silent alert = soft alert = loud alert = vib + loud

16 Octobery 23. Page 6 SWITCH POSITION I and II (OPCODE T and 2U) ( Switch set to GROUP) Switch OPCODE Receiver without vibrator Receiver with vibrator T Decimal group 2U Bleep Volume GROUP X grp = disabled alert = silent GROUP grp = disabled alert = soft GROUP grp = disabled alert = loud Position I Position II Position I Position II grp =enabled alert = silent alert = soft alert = loud grp = disabled alert = vib grp = disabled alert = vib + soft grp = disabled alert = vib + loud *Generally the decimal group call can be enabled or disabled when the switch function is set to alert alert = vib alert = vib + soft alert = vib + loud Bleep Volume with switch set to I or II OPCODE 2U (BIT and 2) Receiver without vibrator Receiver with vibrator silent/soft vib/silent silent/loud vib/soft soft/loud vib/loud loud/loud (vib+loud)/(vib/loud) REMARK: For ease of use refer to 6. Programmable Slide Switch Configuration, which give the possible user switch configurations and their relevant opcode settings:

17 DP 6 DIGITAL PAGING SYSTEM October 23. Page 7 6. PROGRAMMABLE SLIDE SWITCH CONFIGURATIONS Configuration Decimal Group Call DISABLED Opcode T: Bit 2 = Power OFF Switching ENABLED Opcode S: Bit 3 = Slide Switch DON T CARE Opcode 2U: Bit = / Switch Position Receiver without vibrator Receiver with vibrator II Loud Loud + vibrator I Loud Loud + vibrator Power OFF Power OFF II Loud Loud I Soft Vibrator Power OFF Power OFF II Loud Soft I Silent Vibrator Power OFF Power OFF II Soft Silent I Silent Vibrator Power OFF Power OFF Volume Setting Opcode 2U: Bit 2 = Opcode 2U: Bit = Opcode 2U: Bit 2 = Opcode 2U: Bit = Opcode 2U: Bit 2 = Opcode 2U: Bit = Opcode 2U: Bit 2 = Opcode 2U: Bit 2 = Configuration 2 Decimal Group Call DISABLED Opcode T: Bit 2 = Power OFF Switching DISABLED Opcode S: Bit 3 = Slide Switch DON T CARE Opcode 2U: Bit = / Switch Position Receiver without vibrator Receiver with vibrator II Loud Loud + vibrator I Loud Loud + vibrator Soft Soft + vibrator II Loud Loud I Soft Vibrator Silent Vibrator II Loud Soft I Silent Vibrator Silent Vibrator II Soft Silent I Silent Vibrator Silent Vibrator Volume Setting Opcode 2U: Bit 2 = Opcode 2U: Bit = Opcode 2U: Bit 2 = Opcode 2U: Bit = Opcode 2U: Bit 2 = Opcode 2U: Bit = Opcode 2U: Bit 2 = Opcode 2U: Bit =

18 Octobery 23. Page 8 Configuration 3 Decimal Group Call ENABLED Opcode T: Bit 2 = Power OFF Switching ENABLED Opcode S: Bit 3 = Slide Switch ALERT Opcode 2U: Bit = Switch Position Receiver without vibrator Receiver with vibrator II Loud Loud + vibrator I Loud Loud + vibrator Power OFF Power OFF II Loud Loud I Soft Vibrator Power OFF Power OFF II Loud Soft I Silent Vibrator Power OFF Power OFF II Soft Silent I Silent Vibrator Power OFF Power OFF Volume Setting Opcode 2U: Bit 2 = Opcode 2U: Bit = Opcode 2U: Bit 2 = Opcode 2U: Bit = Opcode 2U: Bit 2 = Opcode 2U: Bit = Opcode 2U: Bit 2 = Opcode 2U: Bit = Configuration 4 Decimal Group Call ENABLED Opcode T: Bit 2 = Power OFF Switching DISABLED Opcode S: Bit 3 = Slide Switch ALERT Opcode 2U: Bit = Switch Position Receiver without vibrator Receiver with vibrator II Loud Loud + vibrator I Loud Loud + vibrator Soft Soft + vibrator II Loud Loud I Soft Vibrator Silent Vibrator II Loud Soft I Silent Vibrator Silent Vibrator II Soft Silent I Silent Vibrator Silent Vibrator Volume Setting Opcode 2U: Bit 2 = Opcode 2U: Bit = Opcode 2U: Bit 2 = Opcode 2U: Bit = Opcode 2U: Bit 2 = Opcode 2U: Bit = Opcode 2U: Bit 2 = Opcode 2U: Bit =

19 DP 6 DIGITAL PAGING SYSTEM October 23. Page 9 Configuration 5 Decimal Group Call ENABLED Opcode T: Bit 2 = Power OFF Switching ENABLED Opcode S: Bit 3 = Slide Switch GROUP Opcode 2U: Bit = Switch Position Group Bleep/Vibrator II Group ON Loud + (vibrator) I Group OFF Loud + (vibrator) Power OFF Power OFF II Group ON Soft (+vibrator) I Group OFF Soft (+vibrator) Power OFF Power OFF II Group ON Silent (or vibrator) I Group OFF Silent (or vibrator) Power OFF Power OFF Volume Setting Opcode 2U: Bit 2 = Opcode 2U: Bit = Opcode 2U: Bit 2 = Opcode 2U: Bit = Opcode 2U: Bit 2 = Opcode 2U: Bit = don t care Configuration 6 Decimal Group Call ENABLED Opcode T: Bit 2 = Power OFF Switching DISABLED Opcode S: Bit 3 = Slide Switch GROUP Opcode 2U: Bit = Switch Position Group Bleep/Vibrator II Group ON Loud (+ vibrator) I Group OFF Loud (+ vibrator) Group OFF Soft (+vibrator) II Group ON Soft (+vibrator) I Group OFF Soft (+vibrator) Group OFF Silent (or vibrator) II Group ON Silent (or vibrator) I Group OFF Silent (or vibrator) Group OFF Silent (or vibrator) Volume Setting Opcode 2U: Bit 2 = Opcode 2U: Bit = Opcode 2U: Bit 2 = Opcode 2U: Bit = Opcode 2U: Bit 2 = Opcode 2U: Bit = don t care

20 Octobery 23. Page 2 7. INSTALLER MONITOR AND TEST FUNCTIONS MONITOR / TEST FUNCTIONS II I MONITOR MODE II I 2 3 User switch Programming switch User switch (position I) To enter the Monitor and Test mode of the receiver proceed as follows:. Switch the receiver OFF (3-position user switch (fig. (N) in the lower position) 2. Open the battery compartment and remove the batteries. 3. Place the 3-position utility switch to its programming position (position (fig. P)). 4. Replace the batteries. 5. Switch the receiver ON (3-position user switch to position I or II. The receiver now enters the receiver diagnostic standby mode showing the receiver firmware version and type (e.g. N= numeric display, A = alphanumeric display, S= speech, V = vibrator, X = intrinsically safe). NOTE: While the 3-position utility switch is in the programming position the following is valid:. With the user switch in position the receiver is always switched OFF independent of the opcode setting 2. The functions low battery (bleep), Out-of-range and battery saving are disabled. 3. In diagnostic standby mode the receiver is able to receive and handle calls. After a call has been handled, the receiver returns to the diagnostic standby mode. MONITOR MODE With the User function switch (fig (N)) in the middle position the Monitor standby mode can be entered providing the following functions:. Address monitoring 2. Message monitoring 3. Speech monitoring 4. Call counter ADDRESS MONITORING While in the Monitor standby mode press the RESET/RECALL button once (<2.5 seconds), the receiver enters the receiver address monitoring mode. The numeric display shows AAAAA. The alphanumeric display shows CALL. In this mode each transmitted call in the system results in an attention bleep and the numeric display shows the received address plus codinf. The alphanumeric display shows the address plus codinf on the first line and the 5-digit numeric info and modeword on the second line. MESSAGE MONITORING While in the address monitoring mode press the RESET/RECALL button again (<2.5 seconds) to enter the MESSAGE monitoring mode. The numeric display shows , the alphanumeric displays shows MESSAGE. Each transmitted call in the system results in an attention bleep and the 5-digit numeric info part of the call is displayed in the numeric display and the alphanumeric message of each call is displayed in the alphanumeric display of the receiver. SPEECH MONITORING While in the MESSAGE monitoring mode press the RESET/RECALL button (<2.5 seconds), to enter the SPEECH monitoring mode. The numeric display shows: , and the alphanumeric display shows.speech. In this mode it is possible to switch the speech reproduction ON and OFF. To switch OFF speech press the RESET/RECALL button for longer than 2.5 seconds. To listen to the speech in the system press the RESET/RECALL button again for longer than 2.5 seconds.

21 DP 6 DIGITAL PAGING SYSTEM October 23. Page 2 CALL COUNTER While in the speech monitoring mode press the RESET/RECALL button (<2.5 seconds) to enter the CALL counting mode. The numeric display shows:, and the alphanumeric display shows CALL COUNTER. Every call to the normal call address of this receiver will be counted. Each time such a call is received the receiver emits an attention bleep and the number of received calls is shown in both the numeric and alphanumeric displays. To reset the counter press the RESET/RECALL button for longer than 2.5 seconds. RETURN TO DIAGNOSTIC STANDBY MODE While in the CALL COUNTING mode press the RESET/RECALL button (<2.5 seconds) to return to the diagnostic standby mode. TEST FUNCTIONS II I TEST MODE With the User switch (fig (N) in the upper position the TEST mode can be entered providing the following functions:. Testing bleep and vibrator functions 2. Test both numeric and alphanumeric display and LED indication 3. Show configuration (address and opcodes) 4. Adjusting the contrast of the alphanumeric display TESTING BLEEP and VIBRATOR FUNCTIONS While in the diagnostic standby mode press the RESET/RECALL button (<2.5 seconds to enter the testing bleep and vibrator function. The receiver will bleep and if present the vibrator will vibrate for approx. 4 seconds, or until the RESET/RECALL button is pressed. Numeric displays shows: bbbbb. The alphanumeric display shows: Alert Test. TESTING LED, NUMERIC AND ALPHANUMERIC DISPLAYS + BACKLIGHT LED While in the TESTING BLEEP AND VIBRATION mode press the RESET/ RECALL button (<2.5 seconds) to enter the Testing LED, numeric and alphanumeric displays. The numeric display shows (all segments ON), the alphanumeric shows test symbols from the character set. All icons are ON including three icons which are not used in this receiver but are present for use of this display in other products. After seconds time-out the LEDs are switched OFF automatically. SHOW CONFIGURATION (address, opcodes and user name) While in the TESTING LED, NUMERIC AND ALPHANUMERIC DISPLAYS mode press the RESET/RECALL button (<2.5 seconds) to enter the show configuration mode. To view the receiver s address and opcodes proceed as follows: Using the RESET/RECALL button the following can be viewed in order: - addresses - 6 (in the numeric display 7-digit addresses are shown as follows: alternating ( AA 6 A 5 A 4 to A 3 A 2 A A ) - opcodes and 2 (numeric display shows the last 5 opcode digits only (opcode digit is not used)). - user name

22 Octobery 23. Page 22 TEST FUNCTIONS (contd.) RETURN TO DIAGNOSTIC STANDBY MODE While the user name is displayed, press the RESET/RECALL button (<2.5 seconds) to return to the diagnostic standby mode. ADJUSTING THE CONTRAST OF THE ALPHANUMERIC DISPLAY While in the TEST mode (not the standby Test mode ) press the RESET/RECALL button for longer than 2.5 seconds to enter the CONTRAST adjustment mode. The first line of the alphanumeric display shows ADJUST VLCD and the second line shows value followed by two voltage values. The second voltage value (shown between brackets) gives the currently programmed voltage value of the contrast. The first voltage value is the value of the contrast being viewed. This contrast value can be adjusted by pressing the RESET/RECALL button repeatedly (<2.5 seconds). To store the newly adjusted contrast value, press the RECALL/RESET button for longer than 2.5 seconds. The value shown between brackets is overwritten with the newly set value. To leave this mode switch the 3-position user switch from position II to I and back again. The receiver returns to the diagnostic standby mode.

23 DP 6 DIGITAL PAGING SYSTEM October 23. Page INSTALLER PROGRAMMING INSTALLER PROGRAMMING Programming icon (figure (3)) INTRODUCTION The programming of opcodes and addresses is intended for system installers only. To program receiver opcodes (system/user settings) and receiver call addresses the receiver must be set into its programming mode (see Utility/programming switch in the following section). In its programming mode the receiver displays the programming icon (alphanumeric version only). The settings of the receiver can be programmed by an alphadesk PC or other compatible DP6 encoder. The receiver can be programmed wireless or when placed in a storage/ charging rack connected to the DP6 line. The receiver must be placed in the programming mode (see Utility/programming switch in the following section). The programmed data will remain stored in the receiver until it is overwritten or set to default. Programming should be carried out by the installer or system manager responsible for allocating receiver addresses, opcodes and user names. 3-position utility/ programming switch The utility/programming switch located in the battery compartment behind the batteries is used to place the receiver into its programming mode (See figure P). 2 3 Utility switch Position = Programming mode/disposable batteries (no charging current from rack) Position 2 = Disposable batteries Position 3 = Rechargeable batteries The receiver can be programmed wireless or via its charging/storage rack. To enter the programming mode proceed as follows:. Switch the receiver OFF (3-position user switch (fig. (N) in the lower position) 2. Open the battery compartment and remove the batteries. 3. Place the 3-position utility switch to its programming position (position (fig. P)). 4. Replace the batteries. 5. Switch the receiver ON (3-position user switch to position I or II. The receiver now enters the receiver diagnostic standby mode showing the receivers firmware version. The receiver is now ready for programming as long as it remains in the diagnostic standby mode. NOTE: Each time an address/opcode is programmed wireless an attention bleep is generated by the receiver and the opcode/address is displayed on the display. If the receiver is programmed in a rack the LED will emit a short flash after each programming call. Setting the receiver to Default. Ensure the 3-position utility switch is in its programming position (see above). 2. Switch the receiver OFF, (user switch position ) 3. While pressing the RESET/RECALL button switch the receiver ON (user position I or II). The receivers emits a programming bleep (similar to shut-down-bleep but cricketed) and all settings are set to default (see section 6.3 Total values of opcodes installed).

24 Octobery 23. Page 24 PROGRAMMING 4-digit ADDRESSES Programming 4-digit addresses via the Alphadesk. Enter the Edit menu in the user program 2. Select the Receiver menu item 3. Select program Addresses 4. Enter the receiver Address number ( - 6) and Address digits. Programming the addresses via the LBB 58x desk. Press the program key followed by the key. The desk is now in the programming mode. 2. The desk display shows RAD: 3. Enter the address as follows: N A 3 A 2 A A N = address number ( - 6) A 3.. = address digit PROGRAMMING 7-digit ADDRESSES Programming 7-digit addresses via the Alphadesk (only) The 7-digit address is programmed via a special alphanumeric call. To programme the address proceed as follows:. While in its programming mode send a call to the receiver with the following call string: Address CCC, codinf N (address No. - 6), numeric info EA 3 A 2 A A, alpha message XA 6 A 5 A 4 A 3,A 2 A A (X = don t care digit) Example: To program the address as address number send the following call via the group call menu: CCC E4567 X PROGRAMMING USER NAME JOHN SMITH The user name is programmed via a special alphanumeric call (e.g via the alphadesk). To enter a user name proceed as follows:. While in its programming mode send a call to the receiver with the following call string: Address CCC codinf E, numeric info X (don t care), alpha message user name (max.2 characters) Example: To program the name JOHN SMITH send the following call: CCC E JOHN SMITH

25 DP 6 DIGITAL PAGING SYSTEM October 23. Page 25 PROGRAMMING OPCODES Programming the Opcodes via the alphadesk To program the functions of the receiver, 2 different operation codes (Opcodes) are used. Each Opcode consists of 6 Hex digits where each digit determines one or a group of functions. Each digit of the operation code is represented by the letters P, Q, R, S, T, U, and the function or group of functions assigned to each digit is described further in this chapter.. Enter the Edit menu in the user program 2. Select the receiver menu item 3. Select program opcodes 4. Enter the opcode number M M = 5 if operation code is to be programmed in the receiver M = 6 if operation code 2 is to be programmed in the receiver 5. Enter the opcode (HEX value): P Q R S T U Programming Opcodes via the LBB 58x desk. Press the program key followed by the Opcode number M M = 5 if operation code is programmed in the receiver M = 6 if operation code 2 is programmed in the receiver 2. Enter the opcode hexadecimal value: P Q R S T U (for the description of the opcodes and their functions see below). Description of Opcode Settings The following describes how to read the Operation codes (opcodes) and 2 mentioned in sections 6.2 and 6.3. Both opcodes contains 6 programmable functions: P,Q,R,S,T,U. Below gives the structure of a 4_bit opcode function and an example of how to program Opcode IS. 4_bit opcode Example: Opcode IS value = 8 value = 4 Bit_3 (MSB) Bit_3: Enable Power OFF ( = enable, = disable) Bit_2 Bit_2: Enable battery saving ( = enable, = disable) value = 2 value = Bit_ Bit_ (LSB) Bit_: Enable ALL-Call ( = enable, = disable) Bit_: Enable extended address (=7digits, = 4 digits) Conclusion: Opcode IS = (HEX A)

26 Octobery 23. Page OPERATION CODE (Default: 8A4A) Bits_3 - : Not used = P = P Bits: 3 - : System identity (range HEX - HEX 3) = Q = Q Bit_3: Delete dynamic address when in rack ( = enabled, = disabled) Bit_2: Not used Bit_: Not used Bit_: Not used = 8 = R = R Options Bit_3: Enable Power OFF (=enable, =disable) Bit_2: Enable Battery saving (=enable, =disable) Bit_: Enable ALL-call (=enable, =disable) Bit_: Enable extended address (=7-digit, =4-digit) = HEX A A = S = S Options Bit_3: Enable telemetry address (=enable, =disable) Bit_2: Enable decimal group call (=enable, =disable) Bit_: Accept calls without numeric INFO (=accepted, =not accepted) Bit_: Accept calls with (max.3) error(s) in message (=accept, = not accepted) = 4 = T = T Options Bit_3: Standby mode (=address, =last received INFO) Bit_2: Back-light enable (=enable, =disable) Bit_: Low battery bleep enable (=enable, = disabled) Bit_: Out-of-range enable (=enable, =disable) = HEX A A = U = U Options