SDM SYNCHRONOUS DETECTOR INSTRUCTION MANUAL
|
|
|
- Geoffrey Maxwell
- 6 years ago
- Views:
Transcription
1 Electro Optical Components, Inc Skylane Boulevard, Suite D, Santa Rosa, CA Toll Free: 855-EOC SDM SYNCHRONOUS DETECTOR INSTRUCTION MANUAL rev
2 TABLE OF CONTENTS General Information 3 Application 3 Features 3 Operation conditions 3 Precautions 4 Synchronous detector layout 4 Operating instruction 5-7 Technical characteristics 8 2
3 GENERAL INFORMATION Application SDM synchronous detector enables coordinated operation of the systems with drivers and preamplifiers, measures the voltage signal from the output of photodiode preamplifier and converts it to the DC voltage signal proportional to amplitude of voltage from input. SDM synchronous detector is optimized for work in a pulse mode, since in this mode the highest signal amplitude and STN ratio can be achieved. Features Three independent channels for detection. One can connect three systems with drivers and preamplifiers and run them through the synchronous detector simultaneously. Built-in power supply for preamplifiers. Possibility of input polarity inversion using the appropriate jumper. In case of wrong polarity connection from photodiode preamplifier one can simply switch the input polarity inversion jumper. Operation conditions Indoor operation only. Ingress Protection Rating IP00. Note! Please refer to your provider if you have any questions. 3
4 SYNCHRONOUS DETECTOR LAYOUT Channel 1: 1. Averaging time adjustment jumper: ( 1-100ms, 2-200ms, w/o jumper - 300ms). 2. Input polarity inversion jumper. 3. Signal input (from output of preamplifier) terminal block. 4. Power output terminal block (for preamplifier supply) (DC, unipolar, 5V). 5. Output signal gain adjustment jumper: ( 1 5x gain, 2 10x gain, w/o jumper 1x gain). 6. Signal output terminal block. 7. Synchronization input terminal block (from LED driver synchronization output). Channel 2. Independent channel with its own set of jumpers and terminal blocks. Channel 3. Independent channel with its own set of jumpers and terminal blocks. 8. Power input terminal block (DC, unipolar, +12V). 4
5 OPERATING INSTRUCTIONS 1. Connect preamplifier output wires with signal input terminal block (3) till tight fixation. If you use LMSNT photodiode with a built-in preamplifier (LmsXXPD-XX-RW-PA model), then make a connection in the following way: synchronous detector signal input terminal block photodiode with a built-in preamplifier green cord to the signal input + ; Yellow cord to the signal input 0 Note! The polarity of connections must be observed. In case of alternative polarity connection between photodiode and photodiode preamplifier one can simply switch the input polarity inversion jumper (2). Note! To minimize noise we recommend screening the wires from preamplifier. 2. Connect +5V power output terminal block (4) with preamplifier power input unless external power supply for preamplifier is used. If you use LMSNT photodiode with a built-in preamplifier (LmsXXPD-XX-RW-PA model), then make a connection in the following way: SDM synchronous detector SDM synchronous detector photodiode with a built-in preamplifier 5V power output terminal block White cord to the power output + ; Brown cord to the power output 0 Note! If you use a standalone version of the preamplifier (PAb board), make sure that the connection between the photodiode and the preamplifier is proper, safe and securely screened and take the abovementioned steps
6 OPERATING INSTRUCTIONS Note! Pay your attention to the colours of the cords; actual colours may differ from ones pointed in the present manual, follow the instructions pointed in the technical data provided with the ordered LmsXXPD-XX-RW-PA. 3. Connect signal output terminal block with signal observing device (multimeter, oscilloscope or PC via ADC). signal output terminal block oscilloscope 4. Connect wires from LED driver s synchronization output with synchronization input terminal block (7). synchronisation input terminal block synchronisation output terminal block SDM synchronous detector D-51 LED driver 5. Choose the needed averaging time and signal amplification with the help of the averaging time (1) and signal gain (5) jumpers of the SDM synchronous detector. averaging time jumper signal gain jumper 6
7 OPERATING INSTRUCTIONS 6. If necessary, make all the connections of other boards (driver, thermocontroller etc.) following the appropriate instructions manuals. Before turning them on check the required connections and modes: Driver: Thermocontroller: LED connection Thermistor/D-51 temperature Synchronisation with sync. detector observation block input connection Pulse duration, frequency, current selection External connections (if necessary) Thermocooler output connection External connections (if necessary) 7. Turn on the SDM board connecting +12V power supply with power input terminal block (8). 7
8 TECHNICAL CHARACTERISTICS Power supply voltage +12 V, stabilized Voltage tolerance % Power supply current, max 0.1 A Board dimensions mm Preamplifier supply output voltage 5 V Output constant voltage signal, max 10 V Adjustable parameters Averaging time Signal gain 100/200/300 ms 1x/5x/10x Supported operation modes Pulse duration 2-20 µs Frequency khz Input voltage signal from preamplifier, max ±3 V 8
SDM SYNCHRONOUS DETECTOR INSTRUCTION MANUAL
SDM SYNCHRONOUS DETECTOR INSTRUCTION MANUAL rev. 300117 TABLE OF CONTENTS General Information 3 Application 3 Features 3 Operation conditions 3 Precautions 4 Synchronous detector layout 4 Operating instruction
D-41 UNIVERSAL LED DRIVER INSTRUCTION MANUAL
Electro Optical Components, Inc. 5464 Skylane Boulevard, Suite D, Santa Rosa, CA 95403 Toll Free: 855-EOC-6300 www.eoc-inc.com info@eoc-inc.com D-41 UNIVERSAL LED DRIVER INSTRUCTION MANUAL rev. 160415
D-51 UNIVERSAL LED DRIVER INSTRUCTION MANUAL
Electro Optical Components, Inc. 5464 Skylane Boulevard, Suite D, Santa Rosa, CA 95403 Toll Free: 855-EOC-6300 www.eoc-inc.com info@eoc-inc.com D-51 UNIVERSAL LED DRIVER INSTRUCTION MANUAL rev. 070415
MDS-4 ON-BOARD EVALUATION SYSTEM
Electro Optical Components, Inc. 5464 Skylane Boulevard, Suite D, Santa Rosa, CA 95403 Toll Free: 855-EOC-6300 www.eoc-inc.com info@eoc-inc.com MDS-4 ON-BOARD EVALUATION SYSTEM FOR METHANE DETECTION INSTRUCTION
D-51i UNIVERSAL LED DRIVER INSTRUCTION MANUAL
D-51i UNIVERSAL LED DRIVER INSTRUCTION MANUAL rev. 230317 TABLE OF CONTENTS General Information 3 Application 3 Features 3 Operation conditions 3 Precautions 4 Driver layout 5 Operating mode description
UDK UNIVERSAL EVALUATION KIT INSTRUCTION MANUAL. rev
UDK UNIVERSAL EVALUATION KIT INSTRUCTION MANUAL rev. 250516 TABLE OF CONTENTS General Information 3 Application 3 Packaging arrangement 3 Operation conditions 3 Brief overview of the components included
MCD MULTICHANNEL LED DRIVER INSTRUCTION MANUAL
MCD MULTICHANNEL LED DRIVER INSTRUCTION MANUAL rev. 100616 TABLE OF CONTENTS General Information 3 Application 3 Features 3 Operation conditions 3 Driver layout 4 Operating mode description 5 Operating
MDK EVALUATION KIT FOR METHANE DETECTION INSTRUCTION MANUAL. rev
MDK EVALUATION KIT FOR METHANE DETECTION INSTRUCTION MANUAL rev. 250516 TABLE OF CONTENTS General Information 3 Application 3 Packaging arrangement 3 Operation conditions 3 Brief overview of the components
MDS-3 EVALUATION SYSTEM FOR METHANE DETECTION INSTRUCTION MANUAL
MDS-3 EVALUATION SYSTEM FOR METHANE DETECTION INSTRUCTION MANUAL rev. 281014 TABLE OF CONTENTS General Information 3 Application 3 Packaging arrangement 3 Operation conditions 3 Brief Overview of the Components
Electro Optical Components, Inc.
Electro Optical Components, Inc. 5460 Skylane Boulevard, Santa Rosa, CA 95403 Toll Free: 855-EOC-6300 www.eoc-inc.com info@eoc-inc.com rev 1.01 / 2010 07 02 QBU-BT series Pockels cell driver User Manual
Mid-Infrared (MIR) Photodiode
Current, ma Capacitance, pf Sensitivity, a.u. Sensitivity, a.u. Lms24PD-05 series Device parameters Symbol Value Units Sensitive area diameter d 0.5 mm Storage temperature T stg -50..+60* C Operating temperature
Electro Optical Components, Inc. SUNSTAR 传感与控制 TEL: FAX: Skylane Boulev
Electro Optical Components, Inc. 5460 Skylane Boulevard, Santa Rosa, CA 95403 Toll Free: 855-EOC-6300 www.eoc-inc.com info@eoc-inc.com Features Transimpedance (Gain) Switchable from 1 x 10 3 to 1 x 10
Near-Infrared (NIR) Photodiode
Photosensitivity, A/W Photosensitivity, A/W Current, ma Near-Infrared (NIR) Photodiode Lms24PD-03 series Device parameters Symbol Value Units Sensitive area size Reverse voltage Operating/ storage temperature
Specifications Test Conditions Vs = ± 15 V, Ta = 25 C Gain Gain Values 40, 60, 80, 100 db indicated by four LEDs Gain Accuracy ± 0.1 % (between settin
Electro Optical Components, Inc. SUNSTAR 传感与控制 http://www.sensor-ic.com/ 5460 Skylane Boulevard, Santa Rosa, CA 95403 Toll Free: 855-EOC-6300 www.eoc-inc.com info@eoc-inc.com Features Variable Gain 40
Mid-Infrared (MIR) Photodiode
Photosensitivity, A/W Capacitance, pf Photosensitivity, A/W Current, ma Mid-Infrared (MIR) Photodiode Lms36PD-03 series Device parameters Symbol Value Units Sensitive area size Reverse voltage Operating/
The universal driver for LEDs with built-in cooler DLT-37M
The universal driver for LEDs with built-in cooler DLT-37M Operations manual IBSG Co., Ltd., 26 Polytechnicheskaya str., St-Petersburg, 194021 RUSSIA, ns@iropt6.ioffe.ru, www.ibsg-st-petersburg.com Contents
Mid-Infrared (MIR) Photodiode
Photosensitivity, A/W Photosensitivity, A/W Current, ma Mid-Infrared (MIR) Photodiode Lms41PD-3 series Device parameters Symbol Value Units Sensitive area size Reverse voltage Operating/ storage temperature
Near-Infrared (NIR) Photodiode
Photosensitivity, A/W Capacitance, pf Photosensitivity, A/W Current, ma Near-Infrared (NIR) Photodiode Lms25PD-10 series Device parameters Symbol Value Units Sensitive area diameter Reverse voltage V r
The universal driver for LEDs D-31M
The universal driver for LEDs D-31M Operations manual IBSG Co., Ltd., 26 Polytechnicheskaya str., St-Petersburg, 194021 RUSSIA, ns@iropt6.ioffe.ru, www.ibsg-st-petersburg.com Contents 1. Application 3
AMT-07. Amplifier for MID-IR PDs, with built-in cooler
AMT-07 OPERATION MANUAL Amplifier for MID-IR PDs, with built-in cooler 1. Application The driver AMT-07 is designed for signal extraction and detection from Mid-IR photodiodes with built-in cooler. 2.
Mid-Infrared (MIR) Light-Emitting Diode
Power, µw Current, ma Sensitivity, a.u. Sensitivity, a.u. Mid-Infrared (MIR) Light-Emitting Diode Lms34LEDhp series Device parameters Symbol Value Units Storage temperature Operating temperature Soldering
Electro Optical Components, Inc. SUNSTAR 传感与控制 TEL: FAX: Skylane Boulev
Electro Optical Components, Inc. 5464 Skylane Boulevard, Santa Rosa, CA 9543 Toll Free: 855-EOC-63 www.eoc-inc.com info@eoc-inc.com Application Note 2/9 technical description of JSIR45 The JSIR45 is a
NDR6110 Single Channel Dynamic Driver for Piezoelectric Actuators
NDR61 Driver Series NDR6110 Single Channel Dynamic Driver for Piezoelectric Actuators Features Bipolar and unipolar output load Galvanic separation of the output Adjustable input range and phase inversion
Near-Infrared (NIR) Light-Emitting Diode
Power, mw Current, ma Intensity, a.u. Intensity, a.u. Near-Infrared (NIR) Light-Emitting Diode.5 -.33 μm Lms3LED series Device parameters Symbol Value Units Operating/ storage temperature T stg -..+9*
Mid-Infrared (MIR) Light-Emitting Diode
Power, µw Current, ma Intensity, a.u. Intensity, a.u. Mid-Infrared (MIR) Light-Emitting Diode Lms34LEDhp series Device parameters Symbol Value Units Operating/ storage temperature -6..+9* C Soldering temperature
Mid-Infrared (MIR) Light-Emitting Diode
Intensity, a.u. Power, µw Intensity, a.u. Intensity, a.u. Mid-Infrared (MIR) Light-Emitting Diode.7 -.79 μm Lms7LED series Device parameters Symbol Value Units Operating/ storage temperature -6..+9* C
ELECTRONICS FOR PULSE PICKERS
Rev. 3.07 / 2014 04 10 ELECTRONICS FOR PULSE PICKERS TABLE OF CONTENTS Description... 2 High voltage switches... 3 Appearance / dimensions... 3 Power ratings... 3 Interfaces... 4 Specifications... 6 How
GFT1504 4/8/10 channel Delay Generator
Features 4 independent Delay Channels (10 in option) 100 ps resolution (1ps in option) 25 ps RMS jitter (channel to channel) 10 second range Channel Output pulse 6 V/50 Ω, 3 ns rise time Independent control
(T CASE=25 C) All parameters refer to LEDs in TO18 package with a cavity and operation at ambient temperature 25 C unless otherwise stated.
LED34H series rev 2.0, 03.11.2017 LED34H series are fabricated from narrow band-gap InAs/InAsSbP heterostructures lattice matched to InAs substrate. This Mid-IR LEDs provide a typical peak wavelength of
GFT Channel Digital Delay Generator
Features 20 independent delay Channels 100 ps resolution 25 ps rms jitter 10 second range Output pulse up to 6 V/50 Ω Independent trigger for every channel Four triggers Three are repetitive from three
MTI 7601 PAM Modulation and Demodulation
Page 1 of 1 MTI 7601 PAM Modulation and Demodulation Contents Aims of the Exercise Learning about the functioning principle of the pulse-amplitude modulation (sampling, time division multiplex operation)
LA-T LED ANALYSER EVALUATION KIT INSTRUCTION MANUAL. rev
LA-T LED ANALYSER EVALUATION KIT INSTRUCTION MANUAL rev. 300117 TABLE OF CONTENTS General Information 3 Application 3 Design 3 Features 3 Operation conditions 3 Operation instructions 4-7 2 GENERAL INFORMATION
BINARY AMPLITUDE SHIFT KEYING
BINARY AMPLITUDE SHIFT KEYING AIM: To set up a circuit to generate Binary Amplitude Shift keying and to plot the output waveforms. COMPONENTS AND EQUIPMENTS REQUIRED: IC CD4016, IC 7474, Resistors, Zener
Q106A Oscillator. Aug The Q106A Oscillator module is a combination of the Q106 Oscillator and the Q141 Aid module, all on a single panel.
Aug 2017 The Q106A Oscillator module is a combination of the Q106 Oscillator and the Q141 Aid module, all on a single panel. The Q106A Oscillator is the foundation of any synthesizer providing the basic
SENSORS S62. Compact Sensors - S62. The most complete universal sensor in a compact 50x50 mm housing. Sensors with red, infrared LED or LASER emission
Compact Sensors - S6 S6 The most complete universal sensor in a compact x housing Sensors with red, infrared or LASER emission from 3 cm to m Polarized retroreflective up to 0 m Multivoltage 4-40Vac/4-60Vdc
Department of Electronics & Telecommunication Engg. LAB MANUAL. B.Tech V Semester [ ] (Branch: ETE)
![Department of Electronics & Telecommunication Engg. LAB MANUAL. B.Tech V Semester [ ] (Branch: ETE)](/thumbs/86/93078052.jpg "Department of Electronics & Telecommunication Engg. LAB MANUAL. B.Tech V Semester [ ] (Branch: ETE)")
Department of Electronics & Telecommunication Engg. LAB MANUAL SUBJECT:-DIGITAL COMMUNICATION SYSTEM [BTEC-501] B.Tech V Semester [2013-14] (Branch: ETE) KCT COLLEGE OF ENGG & TECH., FATEHGARH PUNJAB TECHNICAL
HF PA kit with built-in standalone raised cosine controller
AN005 HF PA kit with built-in standalone raised cosine controller 1. Introduction The standard QRP Labs HF PA kit has an 8-bit shift register (74HC595) whose outputs control an 8- bit Digital-to-Analogue
6. has units of bits/second. a. Throughput b. Propagation speed c. Propagation time d. (b)or(c)
King Saud University College of Computer and Information Sciences Information Technology Department First Semester 1436/1437 IT224: Networks 1 Sheet# 10 (chapter 3-4-5) Multiple-Choice Questions 1. Before
SinCosYzer 2 (OVERVIEW) Encoder Signal Analysis With Graphical Visualization
Rev B1, Page 1/5 FEATURES 8 differential input channels for ± 1 V to ± 10 V Fast simultaneous signal sampling up to 2 MS/s High ADC resolution of 30.5 µv at ± 1 V FS (16 bit) Base modes of operation: 8-channel
MODEL GB/S BROADBAND AMPLIFIER
Electro-Absorption Modulator driver or optical receiver amplifier khz - 43 GHz bandwidth 8 ps risetime.7 V amp eye amplitude 8.5 db gain MODEL 5881 4 GB/S BROADBAND AMPLIFIER The 5881 is extremely broadband,
Q106 Oscillator. Controls and Connectors. Jun 2014
The Q106 Oscillator is the foundation of any synthesizer providing the basic waveforms used to construct sounds. With a total range of.05hz to 20kHz+, the Q106 operates as a powerful audio oscillator and
OBSOLETE. High Performance, BiFET Operational Amplifiers AD542/AD544/AD547 REV. B
a FEATURES Ultralow Drift: 1 V/ C (AD547L) Low Offset Voltage: 0.25 mv (AD547L) Low Input Bias Currents: 25 pa max Low Quiescent Current: 1.5 ma Low Noise: 2 V p-p High Open Loop Gain: 110 db High Slew
Chapter 1 Line Code Encoder
Chapter 1 Line Code Encoder 1-1: Curriculum Objectives 1.To understand the theory and applications of line code encoder. 2.To understand the encode theory and circuit structure of NRZ. 3.To understand
Junior Digital circuit experiment board. Use for the experimentation of digital circuits both TTL IC and CMOS DC supply :
NX-100plus Junior Digital circuit experiment board Feature Use for the experimentation of digital circuits both TTL IC and CMOS DC supply : +5V and +V (+12V approx. depend on DC adaptor) 800mA buit-in
Setup of the four-wavelength Doppler lidar system with feedback controlled pulse shaping
Setup of the four-wavelength Doppler lidar system with feedback controlled pulse shaping Albert Töws and Alfred Kurtz Cologne University of Applied Sciences Steinmüllerallee 1, 51643 Gummersbach, Germany
Synchronization. EE442 Lecture 17. All digital receivers must be synchronized to the incoming signal s(t).
Synchronization EE442 Lecture 17 All digital receivers must be synchronized to the incoming signal s(t). This means we must have a way to perform (1) Bit or symbol synchronization (2) Frame synchronization
Variable-Gain High Speed Current Amplifier
Features Transimpedance (gain) switchable from 1 x 10 2 to 1 x 10 8 V/A Bandwidth from DC up to 200 MHz Upper cut-off frequency switchable to 1 MHz, 10 MHz or full bandwidth Switchable AC/DC coupling Adjustable
Exercise 5-1. The Bipolar Power Transistor EXERCISE OBJECTIVES
Exercise 5-1 EXERCISE OBJECTIVES At the completion of this exercise, you will be able to identify different ways of improving bipolar transistor switching. You will know the role of the various circuit
Development of utca Hardware for BAM system at FLASH and XFEL
Development of utca Hardware for BAM system at FLASH and XFEL Samer Bou Habib, Dominik Sikora Insitute of Electronic Systems Warsaw University of Technology Warsaw, Poland Jaroslaw Szewinski, Stefan Korolczuk
Atlantic. Industrial High Power Picosecond Lasers. features
Atlantic Industrial High Picosecond Lasers lasers have been designed as a versatile tool for a variety of industrial material processing applications. They are compact, OEM rugged, with up to 8 W output
Chapter 2 Line Code Decoder
Chapter 2 Line Code Decoder 2-1: Curriculum Objectives 1. To understand the theory and applications of line code decoder. 2. To understand the decode theory and circuit structure of NRZ. 3. To understand
Receiver for Optical Distance Measurement
19-47; Rev ; 7/9 EVALUATION KIT AVAILABLE Receiver for Optical Distance Measurement General Description The is a high-gain linear preamplifier for distance measurement applications using a laser beam.
MODEL 25D MANUAL PRODUCT OVERVIEW:
MODEL 25D MANUAL PRODUCT OVERVIEW: The Model 25D drive electronics is a high voltage push-pull power amplifier capable of output voltage swings in the order of 175v P-P, push-pull. The Model 25D provides
Reconfigurable Laser Servo
Reconfigurable Laser Servo, Inc. www.vescentphotonics.com 4865 E. 41st Ave Denver, CO 80216 Phone: (303)-296-6766 Fax: (303)-296-6783 info@vescent.com General Warnings and Cautions The following general
LED control gear Compact fixed output. Uconverter LCI 50 W 1050 ma N020 TOP series Ø4,5. Ordering data
Product description 1-channel ED control gear Independent ED control gear for indoor use Output current and output voltage adjustable output input channel ominal life of 50,000 h (at ta max. with a failure
AC LAB ECE-D ecestudy.wordpress.com
PART B EXPERIMENT NO: 1 AIM: PULSE AMPLITUDE MODULATION (PAM) & DEMODULATION DATE: To study Pulse Amplitude modulation and demodulation process with relevant waveforms. APPARATUS: 1. Pulse amplitude modulation
SRI SUKHMANI INSTITUTE OF ENGINEERING & TECHNOLOGY DERA BASSI DEPARTMENT: ELECTRONICS & COMM. LABORATORY MANUAL LAB: EMI SUBJECT CODE: SEMESTER: 4th
SRI SUKHMANI INSTITUTE OF ENGINEERING & TECHNOLOGY DERA BASSI DEPARTMENT: ELECTRONICS & COMM. LABORATORY MANUAL LAB: EMI SUBJECT CODE: SEMESTER: 4th EXPERIMENT NO-1 Aim:- Low Resistance Using Kelvin Double
THE BENEFITS OF DSP LOCK-IN AMPLIFIERS
THE BENEFITS OF DSP LOCK-IN AMPLIFIERS If you never heard of or don t understand the term lock-in amplifier, you re in good company. With the exception of the optics industry where virtually every major
Machine Vision Lyte-MV 2
Machine Vision Lyte-MV 2 The Lyte-MV 2 Range The Lyte-MV 2 provides a reliable industrial light source for a wide range of machine vision applications including triangulation, 3D inspection and alignment.
EECS 318 Electronics Lab Laboratory #2 Electronic Test Equipment
EECS 318 Electronics Lab Laboratory #2 Electronic Test Equipment Objectives: The purpose of this laboratory is to acquaint you with the electronic sources and measuring equipment you will be using throughout
5MHz FUNCTION GENERATOR
5MHz FUNCTION GENERATOR MODEL GF-8056 99 Washington Street Melrose, MA 02176 Phone 781-665-1400 Toll Free 1-800-517-8431 Visit us at www.testequipmentdepot.com User s Manual Elenco TM Electronics, Inc.
High Efficiency AC Input 8A 19V Laser Driver
Figure 1. Front View of the Figure 2. Top View of the FEATURES High efficiency: 70% Maximum output current: 8A Wide output voltage: 0V ~ 19V Wide input voltage: 100VAC ~ 240VAC High speed digital modulation:
Understanding The HA2500's Dynamic METER Tests
Understanding The HA2500's Dynamic METER Tests The HA2500's METER Dynamic Tests are designed to analyze parameters of the horizontal output stage with the chassis powered on. Horizontal output stage measurements
Introduction to Basic Laboratory Instruments
Introduction to Contents: 1. Objectives... 2 2. Laboratory Safety... 2 3.... 2 4. Using a DC Power Supply... 2 5. Using a Function Generator... 3 5.1 Turn on the Instrument... 3 5.2 Setting Signal Type...
Lecture 20. Single-phase SPWM inverters
Lecture 20. Single-phase SPWM inverters 20.1 Sinusoidal Pulse Width Modulation (SPWM) In this scheme a sinusoidal modulating voltage ec of the desired output frequency f o is compared with a higher frequency
CALIBRATED IMPULSE GENERATOR MODEL CIG khz 1 GHz
INSTRUCTION MANUAL CALIBRATED IMPULSE GENERATOR MODEL CIG-25 10 khz 1 GHz INSTRUCTION MANUAL THIS INSTRUCTION MANUAL AND ITS ASSOCIATED INFORMATION IS PROPRIETARY. UNAUTHORIZED REPRODUCTION IS FORBIDDEN.
Component List L2, L3 2 Q1, Q2 2 J1, J3, J4 3
19-1061; Rev 1; 1/99 MAX3664 Evaluation Kit General Description The MAX3664 evaluation kit (EV kit) simplifies evaluation of the MAX3664 transimpedance preamplifier. The MAX3664 is optimized for hybrid
High Efficiency AC Input 12A 12V Laser Driver
Figure. Front View of the Figure 2. Top View of the FEATURES High efficiency: 70 % Maximum output current: 2A Wide output voltage: 0V ~ 2V Wide input voltage: 00VAC ~ 240VAC High speed digital modulation:
ModBox-FE-125ps-10mJ. Performance Highlights FEATURES APPLICATIONS. Electrical & Optical Pulse Diagrams
The System-FE-1064nm is set to generate short shaped pulses with high extinction ratio at 1064.1 nm. It allows dynamic extinction ratio up to 55 db with user adjustable pulse duration, repetition rate
Meeting Measurement Challenges For Low-Power, Pulsed, Or Modulated Light Sources
Meeting Measurement Challenges For Low-Power, Pulsed, Or Modulated Light Sources By Denise Ullery, Sylvia Tan, and Jay Jeong, Newport Corporation (www.newport.com) Traditionally, power meters have been
S D 1 Operating Instructions
S D 1 Operating Instructions Volutronic 1. SAFETY 3 2. DESCRIPTION 4 3. CONNECTING THE SD1 5 3.1 Connecting the voltage supply 5 3.2 Connecting SD1 with rectangular output. 5 3.3 Connecting the SD1 with
DESIGN OF AN ANALOG FIBER OPTIC TRANSMISSION SYSTEM
DESIGN OF AN ANALOG FIBER OPTIC TRANSMISSION SYSTEM OBJECTIVE To design and build a complete analog fiber optic transmission system, using light emitting diodes and photodiodes. INTRODUCTION A fiber optic
MPS Electrical Test Laboratory, Larsen & Toubro Limited, Mysore Campus, KIADB Industrial Area, Hebbal Hootagalli, Mysore, Karnataka
Last Amended on - Page 1 of 6 SOURCE 1. DC VOLTAGE $ 1mV to 10 mv 0.13 % to 0.014% Using Multifunction Calibrator 10 mv to 1 V 0.014% to 0.0016% By Direct Method 1 v to 10 V 0.0016% to 0.0017% 10 V to
School of Engineering Mechatronics Engineering Department. Experim. ment no. 1
University of Jordan School of Engineering Mechatronics Engineering Department 2010 Mechatronics System Design Lab Experim ment no. 1 PRINCIPLES OF SWITCHING Copyrights' are held by : Eng. Ala' Bata &
LENORD. +BAUER... automates motion. GEL 2444K PG Configurable rotational speed and position sensor with operating hours counter
GEL 2444K PG Configurable rotational speed and position sensor with operating hours counter LENORD +BAUER... automates motion. Technical information Version 2015-03 General The measuring system comprises
Express Delivery. Axial. Connection
HIGH RESOLUTION INCREMENTAL SOLID SHAFT ENCODER FOR INDUSTRIAL APPLICATIONS Resolution up to 50.000 pulses per turn External diameter 58 mm Shaft from Ø 6 to 12 mm Protection class IP67 according to DIN
POSICHRON position sensor in a stainless steel pressure case. Voltage: V, 3 wire Current: ma, 3 wire
Rod Profile with Analog Specifications POSICHRON position sensor in a stainless steel pressure case Protection class IP68 Compression-proof up to 15 bar Measurement range 0... 100 to 0... 5750 mm Absolute
Agilent 33220A Function Generator Tutorial
Contents UNIVERSITY OF CALIFORNIA AT BERKELEY College of Engineering Department of Electrical Engineering and Computer Sciences EE105 Lab Experiments Agilent 33220A Function Generator Tutorial 1 Introduction
Pin # Pin Name Pin Type Description. 4 GND Signal ground Signal ground pin. Connect ADC and DAC grounds to here.
FEATURES High Efficiency: 90% Maximum Output Current: 2A No Heat Sink Required Current and Power Programming, Modulation & Monitoring Capabilities. Current Output Noise: 0.05% High Stability: 100ppm/ C
IR Antibunching Measurements with id201 InGaAs Gated SPAD Detectors
IR Antibunching Measurements with id201 GaAs Gated SPAD Detectors Abstract. Antibunching measurements with GaAs SPAD detectors are faced with the problems of high background count rate, afterpulsing, and
Chapter 3: DIFFERENTIAL ENCODING
Chapter 3: DIFFERENTIAL ENCODING Differential Encoding Eye Patterns Regenerative Receiver Bit Synchronizer Binary to Mary Conversion Huseyin Bilgekul Eeng360 Communication Systems I Department of Electrical
HAMEG Modular System Series 8000
HAMEG Modular System Series 8000 In many years of practical application the HAMEG Modular System Series 8000 has proven its value to the customer. The advantages of this Modular System have been demonstrated
AC800 FIBRE OPTIC NODE
Broadband Cable Networks / Kari Mäki January 11, 2007 1(6) AC800 FIBRE OPTIC NODE The AC800 is a single active output node. It is based on fixed receiver concept but new features can be added by flexible
GENERAL OPERATING INFORMATION
Fife Corporation P.O. Box 26508, Oklahoma City, OK 73126, USA Phone: 405.755.1600 / Fax: 405.755.8425 www.fife.com / E-mail: fife@fife.com OPERATING MANUAL GENERAL OPERATING INFORMATION General The SDE-30
MEMS Optical Scanner "ECO SCAN" Application Notes. Ver.0
MEMS Optical Scanner "ECO SCAN" Application Notes Ver.0 Micro Electro Mechanical Systems Promotion Dept., Visionary Business Center The Nippon Signal Co., Ltd. 1 Preface This document summarizes precautions
QCXXX-YYDC-ZZZ-AAV. Compact Low Power RF Driver: For Acousto-optic Q-Switch or Modulator. Description: Key Features: Applications:
ompact Low Power RF Driver: For cousto-optic Q-Switch or Modulator QXXX-YYD-ZZZ-V Former Model Numbers: R390XX-YYDMZZZ & MQ0XX-YYDZZZ-V Description: The QXXX-YYD-ZZZ-V module is a compact Low Power RF
PR-E 3 -SMA. Super Low Noise Preamplifier. - Datasheet -
PR-E 3 -SMA Super Low Noise Preamplifier - Datasheet - Features: Low Voltage Noise (0.6nV/ Hz, @ 1MHz single channel mode) Low Current Noise (12fA/ Hz @ 10kHz) f = 0.5kHz to 4MHz, A = 250V/V (customizable)
Application Note (A12)
Application Note (A2) The Benefits of DSP Lock-in Amplifiers Revision: A September 996 Gooch & Housego 4632 36 th Street, Orlando, FL 328 Tel: 47 422 37 Fax: 47 648 542 Email: sales@goochandhousego.com
Variable-Gain High Speed Current Amplifier
Features Transimpedance (Gain) Switchable from 1 x 10 2 to 1 x 10 8 V/A Bandwidth from DC up to 200 MHz Upper Cut-Off Frequency Switchable to 1 MHz, 10 MHz or Full Bandwidth Switchable AC/DC Coupling Adjustable
DUAL DIMMING, EXTENDED TEMPERATURE CCFL INVERTER MODULE. Obsolete. utilizing standard lamp current
Dual Drive, Wide Range Dual Drive Dimming Control. The Dimming, Single Output Inverter. The inverters provide brightness adjustments utilizing standard lamp current LXMG1614E series of Direct Drive CCFL
QUASAR PP & PPR RECTIFIERS
1 9 is a line of switch-mode rectifiers for surface treatment processes, electro-winning and water treatment, that adopts pulse width modulation (PWM) technique for the controlling of current amplitude.
New type ADC using PWM intermediary conversion
ew type ADC using PW intermediary conversion Cristian Zet 1, Cătălin Damian 1, Cristian Foşalău 1 1 Technical University G. Asachi, Bd. D. angeron, 53, 700050, Iasi, ROAIA, phone:+40 232 278683, fa: +40
Software Module MDPP-16-QDC V0003
Software Module MDPP-16-QDC V0003 16 channel VME pulse processor The software module MDPP-16-QDC provides the functionality of a fast charge integrating ADC, a CFD+TDC and a pulse shape discrimination
QCXXX-YYDC-ZZZ-AAV. Compact Low Power RF Driver: For Acousto-optic Q-Switch or Modulator. Description: Key Features: Applications:
ompact Low Power RF Driver: For cousto-optic Q-Switch or Modulator QXXX-YYD-ZZZ-V Former Model Numbers: R0XX-YYDMZZZ & MQ0XX-YYDZZZ-V Description: The QXXX-YYD-ZZZ-V module is a compact Low Power RF Driver,
CAR - TEST - SYSTEM 14
CAR - TEST - SYSTEM 14 EMC-Test Equipment for electrical installation of vehicles Acc. to ISO 7637-2, ISO 16750-2 ISO 21848 Rise time variable 1-5µs Pulse Waveforms : #1 1-5/2000µs, 600 V, ISO 1-5/1000µs,
Chapter 6 Bandwidth Utilization: Multiplexing and Spreading 6.1
Chapter 6 Bandwidth Utilization: Multiplexing and Spreading 6.1 Copyright The McGraw-Hill Companies, Inc. Permission required for reproduction or display. 3-6 PERFORMANCE One important issue in networking
Cornerstone Electronics Technology and Robotics Week 21 Electricity & Electronics Section 10.5, Oscilloscope
Cornerstone Electronics Technology and Robotics Week 21 Electricity & Electronics Section 10.5, Oscilloscope Field trip to Deerhaven Generation Plant: Administration: o Prayer o Turn in quiz Electricity
DIGITAL UTILITY SUB- SYSTEMS
DIGITAL UTILITY SUB- SYSTEMS INTRODUCTION... 138 bandpass filters... 138 digital delay... 139 digital divide-by-1, 2, 4, or 8... 140 digital divide-by-2, 3, 4... 140 digital divide-by-4... 141 digital
PLL Synchronizer User s Manual / Version 1.0.6
PLL Synchronizer User s Manual / Version 1.0.6 AccTec B.V. Den Dolech 2 5612 AZ Eindhoven The Netherlands phone +31 (0) 40-2474321 / 4048 e-mail AccTecBV@tue.nl Contents 1 Introduction... 3 2 Technical
Electro-optic Spectral Decoding Measurements at FLASH
Electro-optic Spectral Decoding Measurements at FLASH, FLA Florian Loehl, Sebastian Schulz, Laurens Wißmann Motivation Development of a robust online bunch length monitor for FLASH and XFEL Transition