DMM8900 SERIES USERS MANUAL
|
|
- Maryann Cox
- 6 years ago
- Views:
Transcription
1 DMM8900 SERIES USERS MANUAL WARRANTY This instrument is warranted to be free from defects in material and workmanship for a period of one year. Any instrument found defective within one year from the delivery date and returned to the factory with transportation charges prepaid, will be repaired, adjusted, or replaced at no charge to the original purchaser. This warranty does not cover expandable items such as batteries or fuses. If the defect has been caused by a misuse or abnormal operation conditions, the repair will be billed at a nominal cost Read the Users Manual thoroughly before use. SAFETY INFORMATION 8900 series digital multimeters have been designed according to IEC-1010 concerning electronic measuring instruments with an overvoltage category (CAT I) and pollution2. ELECTRICAL SYMBOLS AC (Alternating Current) DC (Direct Current) Important safety information. Refer to the manual. Dangerous voltage may be present. Earth ground Fuse Conforms to European Union directives Double insulated WARNING To avoid possible electric shock or personal injury, follow these guidelines: Do not use the meter if it is damaged. Before you use the meter, inspect the case. Pay particular attention to the insulation surrounding the connectors Inspect the test leads for damaged insulation or exposed metal. Check the test leads for continuity. Replace damaged test leads before you use the meter. Do not use the meter if it operates abnormally. Protection may be impaired. When in doubt, have the meter serviced. Do not operate the meter around explosive gas, vapor, or dust. Do not apply more than the rated voltage, as marked on the meter, between terminals or between any terminal and earth ground. Before use, verify the meter s operation by measuring a known voltage
2 When servicing the meter, use only specified replacement parts. Use with caution when working above 30V ac rms, 42V peak, or 60V dc. Such voltages pose a shock hazard. When using the probes, keep your fingers behind the finger guards on the probes. Connect the common test lead before you connect the live test lead. When you disconnect test leads, disconnect the live test lead first. Remove the test leads from the meter before you open the battery door. Do not operate the meter with the battery door or portions of the cover removed or loosened. To avoid false readings, which could lead to possible electric shock or personal injury, replace the batteries as soon as the low battery indicator ( ) appears CAUTION To avoid possible damage to the meter or to the equipment under test, follow these guidelines: Disconnect circuit power and discharge all high-voltage capacitors before testing resistance, continuity, diodes, or capacitance. Use the proper terminals, function, and range for your measurements. Before measuring current, check the meter's fuses and turn power OFF to the circuit before connecting the meter to the circuit. Before rotating the range switch to change functions, disconnect test leads from the circuit under test. Before attempting to insert transistors for testing, always be sure that the test leads have been disconnected from any measurement circuits. Remove test leads from the Meter before opening the Meter case MAINTENANCE Before opening the case, always disconnect the test leads from all live circuits. For continue protection against fire, replace fuse only with the specified voltage and current ratings: F 250mA/250V (Fast Blown) 5 20 Periodically wipe the case with a damp cloth and mild detergent. Do not use abrasives or solvents. INTRODUCTION DMM8900 series multimeters are compact, rugged, battery-powered and handheld 3 1/2- digit LCD digital multimeters for measuring DC and AC voltage, DC and AC current, resistance and diode, capacitance, inductance, battery, frequency, temperature, transistor and continuity test. The Dual-slope A/D Converter uses C-MOS technology for autozeroing, polarity selection and over-range indication. They are ideal instruments for use in field, laboratory and at home. Following table shows the functions of the series multimeters: Model DCV ACV DCA ACA T Hz L BAT
3 UNFUSED V--- BATT FRONT PANEL DIGITAL MULTIMETER A ma COM BATTV DMM8900 V~ 1. FUNCTION AND RANGE SWITCH This switch is used to select the functions and desired ranges as well as to turn ON/OFF the meter. To extend the life of battery, the switch should be set to "OFF" range when the meter is not in use. 2. DISPLAY 3 1/2-digit LCD. 3. "BATT/V/ " JACK Plug-in connector for the red (positive) test lead for all battery, voltage and resistance measurements. 4. "COM" JACK Plug-in connector for black (ne gative) test lead. 5. " A ma" JACK Plug-in connector for the red (positive) test lead for current (less than 200mA) measurement. 6. "10A" JACK Plug-in connector for the red (positive) test lead for current (between 200mA and 10A) measurement There is no fuse in the built-in circuit for "10A" jack. To use safely, each measurement can not last for more than 10 seconds, and the interval between each measurement must be more than 15 minutes. GENERAL SPECIFICATION Maximum voltage between terminal and earth ground Fuse Power supply Display Sampling rate Measuring method Over-range indication CAT I 500V F 250mA/250V 9V battery, NEDA 1604 or 6F22 3 1/2-digit LCD, 1999 counts 2~3 times/sec. Dual-slope integration A/D converter Only figure "1" displayed on the LCD Polarity indication Operating temperature Storage temperature Low battery indication Size Weight "-" displayed for negative 0 ~40 (32 ~104 ) -10 ~50 (14 ~122 ) " " appears on the LCD 86mm(W) 186mm(D) 33mm(H) Approx. 230g (including a 9V battery) TECHNICAL SPECIFICATIONS is specified for a period of one year after calibration and at 18 ~28 (64 ~82 ) with relative humidity up to 75%. specifications take the form of: ([% of Reading]+[Number of Least Significant Digits])
4 DC VOLTAGE DC CURRENT 200mV 2V 20V 200V 500V 100 V 1mV 10mV 100mV 1V Input impedance: 10M for all ranges (0.5% +1) (0.8% +2) 20 A 200 A 2mA 20mA 200mA 10A Maximum input current: 10A 0.01 A 0.1 A 1 A 10 A 100 A 10mA (0.8% +1) (1.0% +1) (1.2% +1) (2.0% +5) AC VOLTAGE AC CURRENT 200mV 2V 20V 200V 400V 100 V 1mV 10mV 100mV 1V (1.2% +3) (1.2% +3) 200 A 2mA 20mA 200mA 20A(10A) 0.1 A 1 A 10 A 100 A 10mA (1.0% +3) (1.8% +3) (3.0% +7) Input impedance: 10M, for all ranges Frequency : 40Hz ~400Hz Indication: Average (rms of sine wave) Frequency range: 40Hz~400Hz Maximum input current: 10A Indication: Average (rms of sine wave)
5 RESISTANCE 200 2k 20K 200K 2M 20 M 200 M K 10K 100K (0.8% +3) (0.8% +1) (1.0% +2) (5%(rdg-10digits) 10digits) Open circuit voltage: Less than 700mV (2.8V for range 200 M ). When the test leads are shorted together at range 200 M, the meter will display the number 101 on the LCD. The number has to be subtracted from measuring results. CAPACITANCE 2000pF 20nF 200nF F 20 F 200 F 1pF 10pF 100pF 1nF 10nF 100nF (2.5% +3) (5.0% +3) DIODE & CONTINUITY Description Test Condition If the resistance of the circuit under test The forward DC current is is less than 30, the built-in buzzer will approx. 1mA, the reversed DC sound. voltage is approx. 2.8V. The approx. forward voltage drop of the Open circuit voltage approx. 2. diode will be displayed on the LCD. 8V. TRANSISTOR hfe TEST PNP & NPN hfe 0~ Test Current 1b=10 A Test Voltage Vce=2.8V TEMPERATURE (K TYPE PROBE) T -40 ~ ~+1000 FREQUENCY 20KHz 10Hz (1.0% +3 ) (1.5% +15 ) (1.0% +5)
6 BATTERY 1.5V 9V INDUCTANCE Description The working current of the battery will be displayed on the LCD so the quality of the battery could be judged. 2mH 20mH 200mH 2H 20H 1 H 10 H 100 H 1mH 10mH Test Condition Working current is about 40mA. Working current is about 24mA. (3.0% +5) (5.0% +5) OPERATING INSTRUCTIONS- DC Voltage Measurement 1. Connect the red test lead to the "BATT/V/ " jack and the black test lead to the "COM" jack. 2. Set the rotary switch to the desired V range. If the voltage to be measured is not known beforehand, set the range switch to the highest range and then turn down range by range until satisfactory resolution is obtained. 3. Connect the test leads to the source or load to be measured. 4. Read the voltage value displayed on the LCD along with the polarity of the red test lead DC Current Measurement 1. Connect the black test lead to the "COM" jack and the red test lead to the " A ma" jack. (While the current to be measured is between 200mA and 10A, remove the red test lead to the "10A" jack.) 2. Set the rotary switch to the desired A range. If the current to be measured is not known beforehand, set the range switch to the highest range and then turn down range by range until satisfactory resolution is obtained. 3. Open the circuit in which the current is to be measured, and connect the test leads in series with the circuit. 4. Read the current value displayed on the LCD along with the polarity of the red test lead. AC Voltage Measurement 1. Connect the red test lead to the "BATT/V/ " jack and the black test lead to the "COM" jack. 2. Set the rotary switch to the desired V range. If the voltage to be measured is not known beforehand, set the range switch at the highest range and then turn down range by range until satisfactory resolution is obtained. 3. Connect the test leads to the source or load to be measured. 4. Read the voltage value displayed on the LCD. AC Current measurement 1. Connect the black test to the "COM" jack and the red test lead to the " A ma" ack. (While the current to be measured is between 200mA and 10A, remove the red test lead to the "10A" jack.)
7 2. Set the rotary switch to the desired A range. If the current to be measured is not known beforehand, set the range switch at the highest range and then turn down range by range until satisfactory resolution is obtained. 3. Open the circuit in which the current is to be measured, and connect the test leads in series with the circuit. 4. Read the current value displayed on the LCD. Resistance Measurement 1. Connect the red test lead to the "BATT/V/ " jack and the black test lead to the "COM" jack. 2. Set the rotary switch to the desired range. 3. Connect the test leads to the resistor to be measured and read the value displayed on the LCD. Note For resistance about 1M and above, the meter may take a few seconds to stabilize. This is normal for high resistance readings. Capacitance Measurement 1. Set the rotary switch to the desired C range. 2. Connect the capacitor to be measured to the input sockets. Note: Observe polarity when connecting polarized capacitors. When testing large capacitances, note that there will be a certain time lag before the indication Temperature Measurement 1. Connect the K type probe to the K probe jack. 2. Set the rotary switch to the "T " range. 3. Read the temperature value displayed on the LCD. Diode Test 1. Connect the red test lead to the "BATT/V/ " jack and the black test lead to the COM jack. (The polarity of the red test lead is positive "+".) 2. Set the rotary switch to " " range. 3. Connect the red test lead to the anode of the diode to be tested and the black test lead to the cathode of the diode. The approximate forward voltage drop of the diode will be displayed on the LCD. If the connection is reversed, only figure "1" will be shown Transistor Test 1. Set the rotary switch to "hfe" range. 2. Determine whether the transistor to be tested is NPN or PNP, and locate the E, B, C leads. Insert the leads into the proper holes of the hfe socket on the front panel. 3. Read the approximate hfe value at the test condition of base current 10 A and Vce 2.8V. Audible Continuity Test 1. Connect the red test lead to the "BATT/V/ " and the black test lead to the "COM" jack. 2. Set the rotary switch to "" range. 3. Connect the test leads to the two terminals of the circuit to be tested. If the resistance is less than about 30, the built-in buzzer will sound
8 Battery Test 1. Set the rotary switch to the "BAT" range. 2. Connect the black test lead to the "COM" jack and the red test lead to the "BATT/V/ " jack. Connect the test leads separately to the two polar of the battery under test. Inductance Measurement 1. Set the rotary switch to the desired "L" range. 2. Connect the inductor to be measured into the input socket "LX". Battery & Fuse Replacement If " " appears on the LCD, it indicates that the battery should be replaced. To replace the battery, open the case, replace the exhausted battery with the ratings specified: 9V, NEDA 1604 or 6F22, and then close the case. The fuse rarely needs to be replaced and is blown as a result of the operator's error. To replace the fuse, open the case, replace the blown fuse with the ratings specified: F 250mA/250V, and then close the case. ACCESSORIES Users Manual Test Leads 9V Battery (NEDA 1604 or 6F22) 1 copy 1pair 1piece
EM420A/420B DIGITAL MULTIMETER OWNERS MANUAL Read this owners manual thoroughly before use
http://www.all-sun.com EM420A/420B DIGITAL MULTIMETER OWNERS MANUAL V Read this owners manual thoroughly before use WARRANTY This instrument is warranted to be free from defects in material and workmanship
More informationDVM98. True RMS Digital Multimeter. 1 Safety information. 1.1 Preliminary. 1.2 During use
True RMS Digital Multimeter DVM98 1 Safety information This multimeter has been designed according to IEC - 1010 concerning electronic measuring instruments with an overvoltage category (CAT II) and pollution
More informationOPERATOR S INSTRUCTION MANUAL DIGITAL MULTIMETER
OPERATOR S INSTRUCTION MANUAL DIGITAL MULTIMETER SAFETY INFORMATION This multimeter has been designed according to IEC 1010 concerning electronic measuring instruments with an overvoltage category (CATⅡ)
More informationOPERATOR S INSTRUCTION MANUAL
OPERATOR S INSTRUCTION MANUAL AUTO-RANGE DUAL DISPLAY CONFORMED IEC1010 DIGITAL MULTIMETER CONTENTS PAGE SAFETY INFORMATION..... DESCRIPTION.. OPERATING INSTRUCTION.. SPECIFICATIONS.... ACCESSORIES. BATTERY
More informationAMM-1022 Digital Multimeter USER`S MANUAL
Digital Multimeter USER`S MANUAL www.tmatlantic.com CONTENTS 1. SAFETY INFORMATION.3 2. DESCRIPTION..6 3. SPECIFICATIONS.8 4. OPERATING INSTRUCTION..11 4.1 Voltage measurement...11 4.2 Current measurement
More informationModel DIGITAL MULTIMETER
Model 57070 DIGITAL MULTIMETER INSTRUCTION MANUAL SAFETY INFORMATION To ensure safe operation, and in order to exploit to the full the functionality of the meter, please follow the directions in this section
More information1. SAFETY 1.1. SAFETY INFORMATION 1.2. SAFETY SYMBOLS
To all residents of the European Union Important environmental information about this product This symbol on the device or the package indicates that disposal of the device after its lifecycle could harm
More informationDIGIT & POINTER MULTIMETER
CONTENTS DIGIT & POINTER MULTIMETER OPERATOR S MANUAL 1. SAFETY INFORMATION 1 1.1 PRELIMINARY 1 1.2 DURING USE 2 1.3 SYMBOLS 3 1.4 MAINTENANCE 3 2. DESCRIPTION 4 2.1 NAMES OF COMPONENTS 4 2.2 FUNCTION
More informationINSTRUCTION MANUAL DIGITAL MULTIMETER
INSTRUCTION MANUAL DIGITAL MULTIMETER 600 OFF 600 20 2m 2 20m m m 2M 10A k 20k 2k O C NPN PNP hfe E B C E 10A DC 10A MAX UNFUSED MAX 600V COM V ma ma MAX FUSED CAT II 600V Thanks for buying our products,
More information1. SAFETY INFORMATION.1 2. DESCRIPTION SPECIFICATIONS.6 4. OPERATING INSTRUCTION Voltage measurement Current measurement 10
CONTENTS 1. SAFETY INFORMATION.1 2. DESCRIPTION..4 3. SPECIFICATIONS.6 4. OPERATING INSTRUCTION..9 4.1 Voltage measurement...10 4.2 Current measurement 10 4.3 Resistance measurement...12 4.4 Diode test.12
More informationDigital Multimeter with Backlight
MODEL: D03126 Digital Multimeter with Backlight 1 CONTENTS Page Number Description 3 Important Safety Information 3 What s Included? 4 Overview 4 Front Panel Description 5 General Specification 5 DC Voltage
More informationDIGITAL MULTIMETER INSTRUCTION MANUAL
DIGITAL MULTIMETER INSTRUCTION MANUAL 1 CONTENTS CONTENTS 1. SAFETY INFORMATION 1 1.1 PRELIMINARY 1 1.2 DURING USE 2 1.3 SYMBOLS 3 1.4 MAINTENANCE 4 2. DESCRIPTION 5 2.1 NAMES OF COMPONENTS 5 2.2 SWITCH,
More informationAUTO RANGING DIGITAL MULTIMETER
AUTO RANGING DIGITAL MULTIMETER 12 MONTH WARRANTY LARGE DIGITAL DISPLAY AC/DC VOLTAGE & CURRENT MEASUREMENT CAT II SAFETY RATING CAT III TEST LEAD SAFETY RATING K8315 ED1 May 17 Table of Contents Know
More informationHANDHELD DIGITAL MULTIMETER OPERATOR S INSTRUCTION MANUAL
HANDHELD DIGITAL MULTIMETER OPERATOR S INSTRUCTION MANUAL GENERAL INSTRUCTIONS This instrument complies with IEC 1010-1 (61010-1@IEC: 2001), CAT. II 1000V and CAT. III 600V overvoltage standards. See Specifications.
More informationItem ref: UK MTM01 DIGITAL MULTITESTER. User Manual
Item ref: 600.100UK MTM01 DIGITAL MULTITESTER User Manual Please read this manual thoroughly and ensure all contents are fully understood before using the apparatus. Warning To avoid possible electric
More informationDIGITAL MULTIMETER OPERATOR'S INSTRUCTION MANUAL HOLD 10A COM LIGHT MS8265 ON/OFF. 200M KHz 2K 20K μ μ μ n.
MS8265 DIGITAL MULTIMETER OPERATOR'S INSTRUCTION MANUAL HOLD ON/OFF LIGHT 1000V CAT II 600V CAT III MS8265 200K 2M 20M 20K 200M KHz 2K 20 200 2 20 200μ 200 20μ 750 2μ 1000 200n F 20n 10A 2m 200m 10 10
More informationM-1000D DIGITAL MULTIMETER
OPERATOR S INSTRUCTION MANUAL DIGITAL MULTIMETER M-1000D Elenco Electronics, Inc. 150 Carpenter Avenue Wheeling, IL 60090 (847) 541-3800 Website: www.elenco.com e-mail: elenco@elenco.com Copyright 2008
More informationThank you again for choosing AstroAI, if you have any questions or concerns regarding your product, please contact us at
ASTROAI USER MANUAL DT132A 4000 Count Auto-Ranging Multimeter Thank you for purchasing the AstroAI DT132A 4000 Count Auto-Ranging Multimeter. It is a 3 ¾ digit, 3999 counts, auto-ranging digital multimeter.
More informationOPERATOR S INSTRUCTION MANUAL M-2625 AUTO RANGING DIGITAL MULTIMETER
OPERATOR S INSTRUCTION MANUAL M-2625 AUTO RANGING DIGITAL MULTIMETER with Temperature Probe Copyright 2007 Elenco Electronics, Inc. Contents 1. Safety Information 3,4 2. Safety Symbols 5 3. Front Plate
More informationSales: Technical: Fax:
DATA SHEET Order code Manufacturer code Description 85-0733 n/a n/a The enclosed information is believed to be correct, Information may change without notice due to product improvement. Users should ensure
More informationMS2030 CAT III 600 V A V AUTO RS232
MS2030 AC Digital Clamp Meter User s Manual CAT III 600 V AUTO RS232 A V CONTENTS 1.Introduction...1 2.Safety Information...1 2.1 Precautions...1 2.2 Safety Symbols...3 3. Description...4 3.1 Front Panel...4
More informationDawson DDM181. Pocket-Size Autorange Digital Meter User s Manual
Dawson DDM181 Pocket-Size Autorange Digital Meter User s Manual 1 Table of Contents LIMITED WARRANTY AND LIMITATION OF LIABILITY... 3 Out of the Box... 3 Accessories... 4 Important Safety Information...
More informationDVM1190 DIGITAL MULTIMETER
DIGITAL MULTIMETER 1. Introduction Thank you for buying the. This digital multimeter has a large LCD, a data-hold function and a backlight. The device uses a very practical safety mechanism that keeps
More informationNOTE: Fully read and understand this manual before using this Digital Multimeter.
ASTROAI USER MANUAL AUTO RANGING DIGITAL CLAMP METER Thank you for purchasing the Auto Ranging Digital Clamp Meter from AstroAI. The AstroAI Auto Ranging Digital Clamp Meter is designed to be safely and
More informationMS8211 DIGITAL MULTIMETER INSTRUCTION MANUAL
MS8211 DIGITAL MULTIMETER INSTRUCTION MANUAL Ω CONTENTS CONTENTS 1. SAFETY INFORM...1 4.4 Range Transform...10 1.1 Preliminary...1 4.5 Auto Power Off...10 1.2 During use...2 4.6 Preparation For Measurement...11
More informationPEN TYPE DIGITAL MULTIMETER OPERATION MANUAL T8211D
PEN TYPE DIGITAL MULTIMETER OPERATION MANUAL T8211D T8211D 1 1. SAFETY INFORMATION BE EXTREMELY CAREFUL IN THE USE OF THIS METER. Improper use of this device can result in electric shock or destroy of
More informationContents 1. General instructions. 1.1 Precautions safety measures Protection mechanisms. 2. Description. 2.1 Instrument Familiarization. 2.
Contents 1. General instructions. 1.1 Precautions safety measures... 1.2 Protection mechanisms. 2. Description. 2.1 Instrument Familiarization. 2.2 LCD Display 2.3 Keypad. 3. Function description. 3.1
More information3B SCIENTIFIC PHYSICS
3B SCIENTIFIC PHYSICS Digital Multimeter E 1018832 Instruction sheet 12/16 SD/UD 1 probe 1a Finger guards 2 Measurement socket 10 A for current measurement in 10-A (positive) 3 Measurement socket COM (negative)
More informationKMD-S04 Multímetro de bolsillo
www.grupotemper.com KMD-S04 Multímetro de bolsillo Table of Contents Title Page Overview ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 3 Unpacking Inspection ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 4 Safety Information
More informationMS6231 DIGITAL ENGINE ANALYZER OPERATOR S MANUAL CONTENTS CONTENTS
CONTENTS MS6231 DIGITAL ENGINE ANALYZER OPERATOR S MANUAL CONTENTS 1. SAFETY INFORMATION 1 1.1 PRELIMINARY 2 1.2 DURING USE 3 1.3 SYMBOLS 5 1.4 MAINTENANCE 6 2. DESCRIPTION 8 2.1 NAMES OF COMPONENTS 9
More informationUser Manual Digital Multimeter
User Manual Digital Multimeter model no.: MSR-R500 Questions or Concerns? support@etekcity.com visit etekcity.com for more products Safe and Proper Usage Thank you for purchasing the Etekcity MSR-R500
More informationMS8216 DIGITAL MULTIMETER OPERATOR S MANUAL
MS8216 DIGITAL MULTIMETER OPERATOR S MANUAL CONTENTS 1. SAFETY INFORMATION 1 1.1 PRELIMINARY 1 1.2 DURING USE 2 1.3 SYMBOLS 4 1.4 MAINTENANCE 4 2. DESCRIPTION 5 2.1 NAMES OF COMPONENTS 5 2.2 FUNCTION AND
More informationTable of Contents Title Page
Table of Contents Title Page Overview Unpacking Inspection Safety Information Rules For Safe Operation International Electrical Symbols The Meter Structure Rotary Switch Functional Buttons Display Symbols
More informationUser s Guide. MultiView Series Digital MultiMeters Models: MV110 MV120 MV130
User s Guide MultiView Series Digital MultiMeters Models: MV110 MV120 MV130 WARRANTY EXTECH INSTRUMENTS CORPORATION warrants this instrument to be free of defects in parts and workmanship for one year
More informationHandheld Digital Multimeter PRO-50A
Handheld Digital Multimeter PRO-50A Safety Summary A statement calls attention to an operating procedure, practice, or condition, which, if not followed correctly, could result in injury or death to personnel.
More informationUser Manual Digital Multimeter. model no.: MSR-U1000
User Manual Digital Multimeter model no.: MSR-U1000 This Operating Manual covers information on safety and cautions. Please read the relevant information carefully and observe all the Warnings and Notes
More informationINSTRUCTION MANUAL MODEL 21 MULTI-TESTER
INSTRUCTION MANUAL MODEL 21 MULTI-TESTER 5 IN 1 SOUND LEVEL LIGHT HUMIDITY TEMPERATURE MULTIMETER .TABLET OF CONTENTS TITLE 1. INTRODUCTION 2 2. INFORMATION FOR SAFETY 2 3. FEATURES 4 4. SPECIFICATIONS
More informationModel : OPERATING MANUAL Table of Contents (1)
Table of Contents (1) Title Overview Unpacking Inspection Safety Information Rules For Safe Operation International Electrical Symbols The Meter Structure Functional Buttons Measurement Operation A. DC
More informationUSER'S MANUAL DMR-4300
USER'S MANUAL DIGITAL MULTIMETER DMR-4300 CIRCUIT-TEST ELECTRONICS www.circuittest.com TABLE OF CONTENTS SAFETY Safety Information...................................... 2 Safety Symbols........................................
More informationInternetowy sklep elektroniczny. Kontakt. Tel Tel. Kom Fax
DOKUMENT TEN JEST PRZEZNACZONY DLA KLIENTÓW FIRMY Internetowy sklep elektroniczny WWW.DIOLUT.PL Kontakt Tel. +48 0334866616 Tel. Kom. +48 0888139522 Fax. +48 0334866617 e-mail diolut@diolut.pl Table of
More informationModel UT39A/B/C: OPERATING MANUAL
TABLE OF CONTENTS TITLE PAGE Overview Unpacking Inspection Safety Information Rules For Safe Operation International Electrical Symbols The Meter Structure Functional Buttons Display Symbols Measurement
More informationAC/DC CLAMP METER USER S MANUAL
AC/DC CLAMP METER USER S MANUAL CONTENTS PAGE SAFETY INFORMATION SYMBOL EXPLANATION SAFETY PRECAUTIONS 1 1 2 MAINTENANCE 3 GENERAL DESCRIPTION 4 PANEL DESCRIPTION 4 OPERATING INSTRUCTIONS... 7 SPECIFICATIONS
More informationProfiScale MULTI Multimeter
1,5 V 9V 200 mv 600 V 200 ma 1/10 A ProfiScale MULTI Multimeter en Operating instructions BURG-WÄCHTER KG Altenhofer Weg 15 58300 Wetter Germany Introduction Want the reassurance of knowing whether current
More informationOWNER S MANUAL HH0308C. AUTO-RANGING DC/True RMS AC DIGITAL MULTIMETER
OWNER S MANUAL HH0308C AUTO-RANGING DC/True RMS AC DIGITAL MULTIMETER IMPORTANT! Read and understand this manual before using the tester. Failure to understand and comply with safety rules and operating
More informationModel UT50D: OPERATING MANUAL. Table of Contents
Table of Contents Overview Unpacking Inspection Safety Information Rules For Safe Operation International Electrical Symbols The Meter Structure Functional Buttons Display Symbols Measurement Operation
More informationDIGITAL MULTIMETER OPERATING INSTRUCTIONS MODEL CDM-35. Part No
DIGITAL MULTIMETER MODEL CDM-35 Part No.4500055 OPERATING INSTRUCTIONS 0304 The Meter may be hung on a wall, or supported as shown, depending upon which support is used. The probes may be located as shown,
More informationCONTENTS MS2033A. 1.Introduction Safety Information...01
MS2033A AC Digital Clamp Meter User s Manual CAT III 600 V CONTENTS 1.Introduction...01 2.Safety Information...01 2.1 Precautions...02 2.2 Safety Symbols...03 3. Description...04 3.1 Front Panel...04 3.2
More information1.General instructions Specifications Description...7
USER S Manual CONTENTS 1.General instructions...1 1.1 Precautions safety measures...1 1.1.1 Preliminary...1 1.1.2 During use...2 1.1.3 Symbols...4 1.1.4 Instructions...5 1.2 Protection mechanisms...6 2.
More informationMS8268 HANDHELD DIGITAL MULTIMETER OPERATOR S INSTRUCTION MANUAL
MS8268 HANDHELD DIGITAL MULTIMETER OPERATOR S INSTRUCTION MANUAL Table of Contents TITLE PAGE 1. GENERAL INSTRUCTIONS 1 1.1 Precaution safety measures 1 1.1.1 Preliminary 1 1.1.2 During use 2 1.1.3 Symbols
More informationMS8223A. CAT.IIi 600 V
Pen-type Digital Multimeter Manual MS8223A CAT.IIi 600 V CONTENTS 1. Safety Information......1 1.1 Preparing for use...1 1.2 During Use......2 1.3 Safety Symbols...3 1.4 Maintenance...4 2. Description......4
More informationDVM645BI BENCH MULTIMETER TAFELMULTIMETER MULTIMETRE DE TABLE BANCO MULTÍMETRO TISCHMULTIMETER. User Manual. Gebruikershandleiding
BENCH MULTIMETER TAFELMULTIMETER MULTIMETRE DE TABLE BANCO MULTÍMETRO TISCHMULTIMETER User Manual Gebruikershandleiding Manuel d'utilisation Gebrauchsanleitung Introduction BENCH MULTIMETER This manual
More informationUT207A/208A/209A Operating Manual. Table of Contents
Table of Contents Title Overview Unpacking Inspection Safety Information Rules for Safe Operation International Electrical Symbols The Meter Structure Display Symbols Functional Buttons The Effectiveness
More informationDigital Clamp Meter Model: &
Digital Clamp Meter Model: 72-7224 & 72-7226 1 SAFETY INFORMATION Please read these instructions carefully before use and retain for future reference. This meter is designed to meet IEC61010-1, 61010-2-032,
More informationUSER'S MANUAL DMR-6700
USER'S MANUAL Multimeter True RMS DMR-6700 CIRCUIT-TEST ELECTRONICS www.circuittest.com Introduction This meter measures AC/DC Voltage, AC/DC Current, Resistance, Capacitance, Frequency (electrical & electronic),
More informationAC/DC DIGITAL CLAMP METER OPERATION MANUAL
AC/DC DIGITAL CLAMP METER OPERATION MANUAL HYS005661 A0 ACCESSORIES 6. ACCESSORIES 1) Test Leads: Electric Ratings 1000V 10A 1 pair (set) 2) Operating Manual 1 copy 3) 1.5V AAA Battery 3 piece - - 55 -
More informationDawson DDM190. Digital Multimeter User s Manual
Dawson DDM190 Digital Multimeter User s Manual TABLE OF CONTENTS LIMITED WARRANTY AND LIMITATION OF LIABILITY... 3 Out of the Box... 3 Accessories.. Error! Bookmark not defined. Safety Information... 7
More informationPocket Size Digital Multimeter Models: and
Pocket Size Digital Multimeter Models: 72-8150 and 72-8155 1 IMPORTANT SAFETY INFORMATION Please read these instructions carefully before use and retain for future reference. Please operate according to
More informationModel UT10A: OPERATING MANUAL Table of Contents (1)
Table of Contents (1) Table of Contents Title Page Overview Unpacking Inspection Safety Information Rules For Safe Operation International Electrical Symbols The Meter Structure Functional Buttons Measurement
More informationModel ST Instruction Manual. True RMS Autoranging Digital Multimeter. reedinstruments. www. com
Model ST-9933 True RMS Autoranging Digital Multimeter Instruction Manual reedinstruments com Table of Contents Safety... 3 Features... 4 Specifications...4-8 Technical...4-5 Accuracy...5-8 Display Description...
More informationDIGITAL MULTIMETER OPERATOR S MANUAL
DIGITAL MULTIMETER OPERATOR S MANUAL CONTENTS 1. SAFETY INFORMATION 1 1.1 PRELIMINARY 1 1.2 DURING USE 2 1.3 SYMBOLS 4 1.4 MAINTENANCE 4 2. DESCRIPTION 5 2.1 NAMES OF COMPONENTS 8 2.2 SWITCH AND BUTTONS
More informationTable of Contents GDM-356. Page
Table of Contents Title Overview Unpacking Inspection Safety Information Rules For Safe Operation International Electrical Symbols The multimeter Structure Functional Buttons Display Symbols Measurement
More informationAX-C Introduction. 2. Safety Information
AX-C708 1. Introduction Read Safety Information before using the meter. ProcessMeter ( referred to as the meter )is a handheld, battery-operated tool for measuring electrical parameters. It has all the
More informationUSER'S MANUAL ACDC-100 TRMS ACDC-100. Versatile AC/DC Clamp-on Multimeter Series
99 Washington Street Melrose, MA 02176 Fax 781-665-0780 TestEquipmentDepot.com USER'S MANUAL ACDC-100 TRMS ACDC-100 Versatile AC/DC Clamp-on Multimeter Series 1 1) SAFETY This manual contains information
More informationMultifunction Digital
MS2009A Multifunction Digital Clamp Meter User Manual 200/600 OFF 2/20 NCV SEL MAX V RAN HOLD OFF MS2009A AC CLAMP METER AUTO MAX C F kmω μmva CONTENTS Safety requirements...1 Safety signs...1 Notes...1
More informationMS8250A/B OPERATION MANUAL MS8250A. Hz% FUNC REL RANGE REL HOLD OFF 10A. Hz% A NCV. Hz% COM. A ma 10A FUSED 600V CAT IV.
MS8250A/B DIGITAL MULTIMETER OPERATION MANUAL AUTO DC AC REL hfe PCLINK % C F kmωkz nµmfav MS8250A DIGITAL MULTIMETER Auto Power Off RANGE REL HOLD FUNC NCV A ma OFF 10A A ma 10A FUSED 600V CAT IV COM
More informationDigital Clamp Meter. User Manual
Digital Clamp Meter User Manual CM240 WWW.OWON.COM.CN Mar. 2016 edition V1.2 Copyright LILLIPUT Company. All rights reserved. The LILLIPUT's products are under the protection of the patent rights, including
More information312, 316, 318. Clamp Meter. Users Manual
312, 316, 318 Clamp Meter Users Manual PN 1989445 July 2002 Rev.2, 2/06 2002, 2006 Fluke Corporation. All rights reserved. Printed in China. All product names are trademarks of their respective companies.
More informationModel : OPERATING MANUAL
Table of Contents Title Page Overview Inspection Safety Information Rules For Safe Operation International Electrical Symbols The Meter Structure Functional Buttons Display Symbols Measurement Operation
More informationModel UT20B: OPERATING MANUAL Table of Contents (1)
Table of Contents (1) Title Overview Unpacking Inspection Safety Information Rules For Safe Operation International Electrical Symbols Rotary Switch Display Symbols Measurement Operation A. AC Voltage
More informationItem ref: UK MTTR01 TRUE RMS DIGITAL MULTITESTER WITH USB INTERFACE. User Manual
Item ref: 600.104UK MTTR01 TRUE RMS DIGITAL MULTITESTER WITH USB INTERFACE User Manual Please read this manual thoroughly and ensure all contents are fully understood before using the apparatus. WARNING
More informationAnalog Technologies VC99. Multimeter FEATURES
FEATURES LCD Display Max Display: 6000(3 6/7) Digits Automatic Polarity, Unit Symbol and 61 Section Analog Display Measurement Method: Double Integral A/D Conversion Sampling Rate: Approx.3 times/sec Over-Range
More informationUser Manual. All rights reserved. Specifications are subject to change without notice.
User Manual All rights reserved. Specifications are subject to change without notice. LIMITED WARRANTY AND LIMITATION OF LIABILITY Customers enjoy one-year warranty from the date of purchase. This warranty
More informationDIGITAL MULTIMETER AUTORANGING
MODEL: D03124 DIGITAL MULTIMETER AUTORANGING 1 CONTENTS Page Number Details 2 Introduction 2 What s Included 3 Important Safety Information 3 Symbol Guide 4 Overview 5 Buttons 5 Display Indicators 6 General
More informationUSER'S MANUAL DMR-2400
USER'S MANUAL DIGITAL MULTIMETER DMR-2400 CIRCUIT-TEST ELECTRONICS www.circuittest.com TABLE OF CONTENTS SAFETY Safety Information...................................... 2 Safety Symbols........................................
More informationMS8250D DUAL DISPLAY DIGITAL MULTIMETER User s Manual
DUAL DISPLAY DIGITAL MULTIMETER User s Manual MS8250D 1. Safety Information Warning Use caution and follow all safety guidelines to prevent electric shock or damage to the meter. Please ready carefully
More informationET-3888 True RMS Clamp Meter. User Manual
ET-3888 True RMS Clamp Meter User Manual Index Introduction... 3 Safety Notes... 4 Features... 5 Specifications... 6-8 Instrument Layout... 9 Measurement... 10 Maintenance... 11 Page 2 1. Introduction
More informationDIGITAL MULTIMETER CONTENTS DIGITAL MULTIMETER CONTENTS
CONTENTS CONTENTS CONTENTS 1. SAFETY INFORMATION...1 1.1 Preliminary...1 1.2 Dos and don ts...2 1.3 Symbols...3 1.4 Precautions...4 2. DESCRIPTION...5 2.1 Names of parts...6 2.2 Switches, buttons and input
More informationVC835 DIGTAL MULTIMETER Operation Manual
VC835 DIGTAL MULTIMETER Operation Manual CONTENTS GENERAL DESCRIPTION Safety Instructions FEATURES OPERATION MAINTENANCE TROUBLE SHOOTING 1. General Description This is a 3 1/2 digital multimeter with
More informationDIGITAL MULTIMETER AX-588B
DIGITAL MULTIMETER AX-588B OPERATION MANUAL 1. Sumary His series product is a stable and battery-driven 3 ½ digital multimeter with high reliability. It adopts LCD screen with character height of 28mm;
More informationDigital Multimeter AX-572. Instruction manual
Digital Multimeter AX-572 Instruction manual 1. SUMMARIZE The meter is a stable multimeter with 40mm LCD display, driven by battery. It's widely used on measuring DCV, ACV, DCA, ACA, resistance, capacitance,
More informationETHOS 5030 TRUE-RMS DIGITAL MULTIMETER OPERATION MANUAL
ETHOS 5030 TRUE-RMS DIGITAL MULTIMETER OPERATION MANUAL 1 1. SAFETY INFORMATION SAFETY SYMBOLS Warning! Dangerous Voltage (Risk of electric shock). Caution! Refer to the user s manual before using this
More information15B & 17B. Users Manual. Multimeters
15B & 17B Multimeters Users Manual PN 1991246 October 2002 Rev. 3, 3/04 2002-2004 Fluke Corporation. All rights reserved. Printed in China. All product names are trademarks of their respective companies.
More informationUser s Guide. Digital AC/DC Clamp Meter Model 38394
User s Guide Digital AC/DC Clamp Meter Model 38394 Introduction Congratulations on your purchase of Extech s 38394 AC/DC Clamp Meter. This clamp meter measures AC/DC Current to 600A, DC/AC Voltage, Resistance,
More informationUT132 Series Manual. UT132 Series. Palm Size Digital Multimeter. Operating Manual -1-
UT132 Series UT132 Series Manual Palm Size Digital Multimeter Operating Manual -1- Table of Contents 一 Overview 二 Unpacking Inspection 三 Safety Information 四 International Electrical Symbols 五 Overall
More informationDigital Multimeter, Pen Type
MODEL: D03127 Digital Multimeter, Pen Type 1 CONTENTS Page Number Description 3 Important Safety Information 3 Electrical Symbols 4 Overview 4 Measurement Operation 5 AC & DC Voltage Measurement 5 AC &
More informationUser Manual Digital Clamp Multimeter. model no.: MSR-C600
User Manual Digital Clamp Multimeter model no.: MSR-C600 Overview This Operating Manual covers information on safety and cautions. Please read the relevant information carefully and observe all the Warnings
More informationIDEAL INDUSTRIES, INC. TECHNICAL MANUAL MODEL: MODEL: Multimeter Service Information
IDEAL INDUSTRIES, INC. TECHNICAL MANUAL MODEL: 61-340 MODEL: 61-342 Multimeter Service Information The Service Information provides the following information: Precautions and safety information Specifications
More informationUSER'S MANUAL AM-100 AM-105 TRMS AM-110 TRMS. Digital Multimeters
USER'S MANUAL AM-100 AM-105 TRMS AM-110 TRMS Digital Multimeters 1 1) SAFETY This manual contains information and warnings that must be followed for operating the instrument safely and maintaining the
More informationINSTRUCTION MANUAL. Model Autoranging DMM ProbeMeter TM. Measures voltage, resistance, frequency, capacitance, temperature, and duty cycle.
INSTRUCTION MANUAL Model 403380 Autoranging DMM ProbeMeter TM Measures voltage, resistance, frequency, capacitance, temperature, and duty cycle. Back lit LCD with Autorange and full function displays Audible
More informationUSER S MANUAL DMR-1500
USER S MANUAL DIGITAL POCKET MULTIMETER DMR-1500 CIRCUIT-TEST ELECTRONICS www.circuittest.com TABLE OF CONTENTS SAFETY Safety Information............................... 2-3 Safety Symbols...................................
More informationUSER MANUAL 600A AC Clamp Meter + NCV Model MA610
USER MANUAL 600A AC Clamp Meter + NCV Model MA610 Additional User Manual Translations available at www.extech.com Introduction Thank you for selecting the Extech MA610 Clamp Meter. This meter measures
More informationPen-type DIGITAL MULTITESTER
BST-MT267 Pen-type DIGITAL MULTITESTER INSTRUCTION MANUAL Index 1. Introduction... 2. Safety Notes... 3. Features... 4. Specifications... 5. General... 6. Instrument Layout... 7. Measurement... 8. Maintenance...
More informationUSER'S MANUAL TBM061 TBM062 TBM063 TBM065
USER'S MANUAL TBM061 TBM062 TBM063 TBM065 Compact AC/DC Clamp-on Multimeter Series 1 1) SAFETY This manual contains information and warnings that must be followed for operating the instrument safely and
More informationDIGITAL DUAL DISPLAY AC/DC CLAMP METER MODEL-860A OPERATION MANUAL
DIGITAL DUAL DISPLAY AC/DC CLAMP METER MODEL-860A OPERATION MANUAL DIGITAL DUAL DISPLAY AC/DC CLAMP METER MODEL-860A TABLE OF CONTENTS TITLE PAGE Safety Information Safety Symbols... 1 Meter Description...
More informationIDEAL INDUSTRIES, INC. TECHNICAL MANUAL MODEL:
IDEAL INDUSTRIES, INC. TECHNICAL MANUAL MODEL: 61-352 The Service Information provides the following information: Precautions and safety information Specifications Basic maintenance (cleaning, replacing
More informationDigital Clamp Meter (TRMS) Model : 2727
Digital Clamp Meter (TRMS) Model : 2727 Instruction Manual 1. SPECIFICATIONS 1.1 General Specifications Display : 3 ¾ digit liquid crystal display (LCD) with a maximum reading of 3999. Polarity : Automatic,
More informationUser Guide. Digital AC/DC Clamp Meter Model 38394
User Guide Digital AC/DC Clamp Meter Model 38394 Introduction Congratulations on your purchase of Extech s 38394 AC/DC Clamp Meter. This clamp meter measures AC/DC Current to 600A, DC/AC Voltage, Resistance,
More informationAnalog Technologies. Multimeter 15B and17b
Figure 1. The Photo of Actual 17B Figure 2. The Photo of Actual 15B FEATURES Maximum Voltage between Any Terminal and Earth Ground: 1000V Temperature Coefficient: 0.1 (specified accuracy)/ (28
More informationRAGU 81D DIGITAL MULTIMETER OPERATION MANUAL
RAGU 81D DIGITAL MULTIMETER OPERATION MANUAL Contents I. General...- 1 - Ⅱ. Open-package Inspection...- 2 - III. Safety Considerations... - 3 - IV.Instrument Panel & Button Function Description...- 9 -
More informationAM-510 Commercial / Residential Multimeter. AM-510-EUR Digital Multimeter. Users Manual
AM-510 Commercial / Residential Multimeter AM-510-EUR Digital Multimeter Users Manual AM-510 Commercial / Residential Multimeter AM-510-EUR Digital Multimeter English Users Manual Limited Warranty and
More information