Description. Order code Operating temp. range Package Packaging

Size: px

Start display at page:

Download "Description. Order code Operating temp. range Package Packaging"

Chad Roberts
6 years ago
Views:

1 00-watt + 00-watt dual BTL class-d audio amplifier Features 00-W + 00-W output power at THD = 0% with R L = 6 Ω and V CC = 36 V 80-W + 80-W output power at THD = 0% with R L = 8 Ω and V CC = 34 V Wide-range single-supply operation (4-39 V) High efficiency (η = 90%) Four selectable, fixed gain settings of nominally 5.6 db, 3.6 db, 35. db and 37.6 db Differential inputs minimize common-mode noise Standby and mute features Short-circuit protection Thermal overload protection Externally synchronizable Description PowerSSO36 with exposed pad up The is a dual BTL class-d audio amplifier with single power supply designed for home systems and active speaker applications. It comes in a 36-pin PowerSSO package with exposed pad up (EPU) to facilitate mounting a separate heatsink. Table. Device summary Order code Operating temp. range Package Packaging -40 to 85 C PowerSSO36 (EPU) Tube TR -40 to 85 C PowerSSO36 (EPU) Tape and reel September 0 Doc ID 607 Rev 8 /8 8

2 Contents Contents Pin description Pinout Pin list Electrical specifications Absolute maximum ratings Thermal data Recommended operating conditions Electrical specifications Characterizations Test circuit Characterization curves For R L = 6 Ω For R L = 8 Ω Applications information Applications circuit Mode selection Gain setting Input resistance and capacitance Internal and external clocks Master mode (internal clock) Slave mode (external clock) Output low-pass filter Protection functions Diagnostic output Package mechanical data Revision history /8 Doc ID 607 Rev 8

3 List of figures List of figures Figure. Internal block diagram (showing one channel only) Figure. Pin connections (top view, PCB view) Figure 3. Test circuit for characterizations Figure 4. Test board Figure 5. Output power (THD = 0%) vs. supply voltage Figure 6. THD vs. output power Figure 7. THD vs. frequency ( W) Figure 8. THD vs. frequency (00 mw) Figure 9. Frequency response Figure 0. FFT performance (0 dbfs) Figure. FFT performance (-60 dbfs) Figure. Output power (THD = 0%) vs. supply voltage Figure 3. THD vs. output power Figure 4. THD vs. frequency ( W) Figure 5. THD vs. frequency (00 mw) Figure 6. Frequency response Figure 7. FFT performance (0 db) Figure 8. FFT performance (-60 db) Figure 9. Applications circuit for 6- or 8-Ω speakers Figure 0. Standby and mute circuits Figure. Turn on/off sequence for minimizing speaker pop Figure. Input circuit and frequency response Figure 3. Master and slave connection Figure 4. Typical LC filter for a 8-Ω speaker Figure 5. Typical LC filter for a 6-Ω speaker Figure 6. Behavior of pin DIAG for various protection conditions Figure 7. PowerSSO36 EPU outline drawing Doc ID 607 Rev 8 3/8

4 List of tables List of tables Table. Device summary Table. Pin description list Table 3. Absolute maximum ratings Table 4. Thermal data Table 5. Recommended operating conditions Table 6. Electrical specifications Table 7. Mode settings Table 8. Gain settings Table 9. How to set up SYNCLK Table 0. PowerSSO36 EPU dimensions Table. Document revision history /8 Doc ID 607 Rev 8

5 Device block diagram Device block diagram Figure shows the block diagram of one of the two identical channels of the. Figure. Internal block diagram (showing one channel only) Doc ID 607 Rev 8 5/8

6 Pin description Pin description. Pinout Figure. Pin connections (top view, PCB view) 36 VSS SUB_GND 35 SVCC OUTPB 34 VREF OUTPB 3 33 INNB PGNDB 4 3 INPB PGNDB 5 3 GAIN PVCCB 6 30 GAIN0 PVCCB 7 9 SVR OUTNB 8 8 DIAG OUTNB 9 7 SGND OUTNA 0 6 VDDS OUTNA 5 SYNCLK PVCCA 4 ROSC PVCCA 3 3 INNA PGNDA 4 INPA MUTE EP, exposed pad Connect to ground PGNDA OUTPA STBY OUTPA 7 9 VDDPW PGND 8 6/8 Doc ID 607 Rev 8

7 Pin description. Pin list Table. Pin description list Number Name Type Description SUB_GND PWR Connect to the frame,3 OUTPB O Positive PWM for right channel 4,5 PGNDB PWR Power stage ground for right channel 6,7 PVCCB PWR Power supply for right channel 8,9 OUTNB O Negative PWM output for right channel 0, OUTNA O Negative PWM output for left channel,3 PVCCA PWR Power supply for left channel 4,5 PGNDA PWR Power stage ground for left channel 6,7 OUTPA O Positive PWM output for left channel 8 PGND PWR Power stage ground 9 VDDPW O 0 STBY I Standby mode control MUTE I Mute mode control 3.3-V (nominal) regulator output referred to ground for power stage INPA I Positive differential input of left channel 3 INNA I Negative differential input of left channel 4 ROSC O Master oscillator frequency-setting pin 5 SYNCLK I/O Clock in/out for external oscillator 6 VDDS O 7 SGND PWR Signal ground 8 DIAG O Open-drain diagnostic output 9 SVR O Supply voltage rejection 30 GAIN0 I Gain setting input 3 GAIN I Gain setting input 3.3-V (nominal) regulator output referred to ground for signal blocks 3 INPB I Positive differential input of right channel 33 INNB I Negative differential input of right channel 34 VREF O Half VDDS (nominal) referred to ground 35 SVCC PWR Signal power supply 36 VSS O 3.3-V (nominal) regulator output referred to power supply - EP - Exposed pad for heatsink, to be connected to ground Doc ID 607 Rev 8 7/8

8 Electrical specifications Electrical specifications. Absolute maximum ratings Table 3. Absolute maximum ratings Symbol Parameter Value Unit V CC DC supply voltage for pins PVCCA, PVCCB, SVCC 44 V VI Voltage limits for input pins STBY, MUTE, INNA, INPA, INNB, INPB, GAIN0, GAIN -0.3 to 3.6 V T j Operating junction temperature -40 to 50 C T stg Storage temperature -40 to 50 C. Thermal data Table 4. Thermal data Symbol Parameter Min Typ Max Unit R th j-case Thermal resistance, junction to case - 3 C/W.3 Recommended operating conditions Table 5. Recommended operating conditions Symbol Parameter Min Typ Max Unit V CC Supply voltage for pins PVCCA, PVCCB, SVCC 4-39 V Tamb Ambient operating temperature C.4 Electrical specifications Unless otherwise stated, the values in the table below are specified for the conditions: V CC =36V, R L = 6 Ω, R OSC = R3 = 39 kω, C8 = 00 nf, f = khz, G V = 5.6 db Tamb = 5 C. Table 6. Electrical specifications Symbol Parameter Condition Min Typ Max Unit I q Total quiescent current No LC filter, no load ma I qstby Quiescent current in standby µa V OS Output offset voltage Play mode Mute mode I OCP Overcurrent protection threshold R L = 0 Ω A mv 8/8 Doc ID 607 Rev 8

9 Electrical specifications Table 6. T j Junction temperature at thermal shutdown C R i Input resistance Differential input kω V OVP Overvoltage protection threshold V V UVP Undervoltage protection threshold V R dson P o Power transistor on resistance Output power High side Low side THD = 0% THD = % P o Output power R L = 8 Ω, THD = 0% W P P D Dissipated power o = 00 W + 00 W, W THD = 0% η Efficiency P o = 00 W + 00 W % THD Total harmonic distortion P o = W % G V Closed-loop gain GAIN0 = L, GAIN = L GAIN0 = L, GAIN = H GAIN0 = H, GAIN = L GAIN0 = H, GAIN = H ΔG V Gain matching db C T Crosstalk f = khz, P o = W db en Total input noise A Curve, G V = 0 db f = Hz to khz SVRR Supply voltage rejection ratio fr = 00 Hz, Vr = 0.5 Vpp, C SVR = 0 µf db T r, T f Rise and fall times ns f SW Switching frequency Internal oscillator khz f SWR Electrical specifications (continued) Symbol Parameter Condition Min Typ Max Unit Output switching frequency range With internal oscillator () With external oscillator () V inh Digital input high (H) V inl Digital input low (L) Ω W db µv khz V Doc ID 607 Rev 8 9/8

10 Electrical specifications Table 6. Electrical specifications (continued) Symbol Parameter Condition Min Typ Max Unit V STBY Pin STBY voltage high (H) Pin STBY voltage low (L) V V MUTE Pin MUTE voltage high (H) Pin MUTE voltage low (L) V A MUTE Mute attenuation V MUTE = L, V STBY = H db. f SW = 0 6 / ((6 R OSC + 8) 4) khz, f SYNCLK = f SW with R3 = 39 kω (see Figure 9.).. f SW = f SYNCLK / with the external oscillator. 0/8 Doc ID 607 Rev 8

11 3V3 Doc ID 607 Rev 8 /8 3 Characterizations 3. Test circuit Figure 3 shows the test circuit with which the characterization curves, shown in the next sections, were measured. Figure 4 shows the PCB layout. Figure 3. Test circuit for characterizations J INPUT 3 L- L+ 3V3 4 R- R+ J4 FS C uf C uf FREQUENCY SHIFT Q R9 KTC3875(S) 80K 3 R3 C8 FS 00nF 47k R4 00k For Single-Ended Input C uf C S uf MUTE 3 S STBY 3 3V3 POWER SUPPLY C5 00nF For R7 J7 Single-Ended R Input C6 00nF J8 OUT IC IN L493CZ33 3 C9 GND C9 00nF.uF VDDS R4 0k R 33k R8 VCC 6.8k D 8V C3 nf R3 39K SUB_GND INPA 3 INNA C4 nf 7 SGND VDDS 6 VDDS R 8 DIAG 00k DIAG 9 VDDPW 8 PGND 5 SYNCLK 4 ROSC J5 30 GAIN0 C0 3 GAIN J6 35 SVCC 00nF 36 VSS 3 INPB C3 nf 33 INNB C4 nf MUTE + C5.uF 6V 0 STBY + C7.uF 6V IC OUTPA 6 OUTPA 7 PGNDA PGNDA OUTNA 0 OUTPB PVCCB PGNDB OUTNB C5 00nF PVCCA OUTPB PVCCB PGNDB OUTNB SVR C9 00nF CLASS-D AMPLIFIER 4 5 PVCCA 3 OUTNA VREF R6 R C30 uf C7 330pF R5 R C3 uf C 330pF C7 0uF 0V C6 0uF 0V L4 uh L3 uh L uh L uh C6 680nF C0 680nF C8 0nF C4 0nF 00uF C3+ 50V C8 0nF C 0nF R5 8R C40 0nF C4 0nF R6 8R VCC GND J R7 8R C4 0nF C43 0nF R8 8R LC FILTER COMPONENTS Load L,L,L3,L4 C0,C6 C8,C,C4,C8 6 ohm uh 680 nf 0 nf 8 ohm uh 470 nf 0 nf J3 OUTPUT Load = 6 ohm L+ L- R- 3 R+ 4 Characterizations

12 Characterizations Figure 4. Test board /8 Doc ID 607 Rev 8

13 Characterizations 3. Characterization curves Unless otherwise stated the measurements were made under the following conditions: V CC = 36 V, f = khz, G V = 5.6 db, R OSC = 39 kω, C OSC = 00 nf, Tamb = 5 C 3.. For R L = 6 Ω Figure 5. Output power (THD = 0%) vs. supply voltage 0 0 Output power (W) Supply voltage (V) Figure 6. THD vs. output power 0 5 THD+N (%) f = khz 0.05 f = 00 Hz m 00m 500m Output power (W) Doc ID 607 Rev 8 3/8

14 Characterizations Figure 7. THD vs. frequency ( W) THD+N (%) k k 5k 0k 0k Frequency (Hz) Figure 8. THD vs. frequency (00 mw) THD+N (%) k k 5k 0k 0k Frequency (Hz) Figure 9. Frequency response Ampl (db) k k 5k 0k 0k Frequency (Hz) 4/8 Doc ID 607 Rev 8

15 Characterizations Figure 0. FFT performance (0 dbfs) FFT (db) k k 5k 0k 0k Frequency (Hz) Figure. FFT performance (-60 dbfs) FFT (db) k k 5k 0k 0k Frequency (Hz) Doc ID 607 Rev 8 5/8

16 Characterizations 3.. For R L = 8 Ω Figure. Output power (THD = 0%) vs. supply voltage 0 0 Output power (W) Supply voltage (V) Figure 3. THD vs. output power 0 5 THD+N (%) f = khz f = 00 Hz m 00m 500m Output power (W) 6/8 Doc ID 607 Rev 8

17 Characterizations Figure 4. THD vs. frequency ( W) THD+N (%) k k 5k 0k 0k Frequency (Hz) Figure 5. THD vs. frequency (00 mw) THD+N (%) k k 5k 0k 0k Frequency (Hz) Figure 6. Frequency response Ampl (db) k k 5k 0k 0k Frequency (Hz) Doc ID 607 Rev 8 7/8

18 Characterizations Figure 7. FFT performance (0 db) Figure 8. FFT performance (-60 db) FFT (db) k k 5k 0k 0k Frequency (Hz) 8/8 Doc ID 607 Rev 8

19 3V3 Doc ID 607 Rev 8 9/8 4 Applications information 4. Applications circuit Figure 9. J Applications circuit for 6- or 8-Ω speakers INPUT L- 3V3 3 4 L+ R- R+ J4 FS C uf C uf FREQUENCY SHIFT Q R9 KTC3875(S) 80K 3 R3 C8 FS 00nF 47k R4 00k For Single-Ended Input C uf C S uf MUTE 3 S STBY 3 3V3 POWER SUPPLY C5 00nF For R7 J7 Single-Ended R Input C6 00nF J8 OUT IC IN L493CZ33 3 C9 GND C9 00nF.uF VDDS R4 0k R 33k R8 VCC 6.8k D 8V C3 nf R3 39K 00nF 36 VSS C4 nf SUB_GND INPA 3 INNA C4 nf 7 SGND VDDS 6 VDDS R 8 DIAG 00k DIAG C0 C3 nf + C5.uF 6V + C7.uF 6V 9 VDDPW 8 PGND 5 SYNCLK 4 ROSC J5 30 GAIN0 3 GAIN J6 35 SVCC 3 INPB 33 INNB MUTE 0 STBY IC OUTPA 6 OUTPA 7 PGNDA PGNDA OUTNA 0 OUTPB PVCCB PGNDB OUTNB C5 00nF PVCCA OUTPB PVCCB PGNDB OUTNB SVR C9 00nF CLASS-D AMPLIFIER 4 5 PVCCA 3 OUTNA VREF R6 R C30 uf C7 330pF R5 R C3 uf C 330pF C7 0uF 0V C6 0uF 0V L4 uh L3 uh L uh L uh C6 680nF C0 680nF C8 0nF C4 0nF 00uF C3+ 50V C8 0nF C 0nF R5 8R C40 J3 0nF OUTPUT Load = 6 ohm L+ C4 L- 0nF R- R6 3 R+ 8R 4 VCC GND J R7 8R C4 0nF C43 0nF R8 8R LC FILTER COMPONENTS Load L,L,L3,L4 C0,C6 C8,C,C4,C8 6 ohm uh 680 nf 0 nf 8 ohm uh 470 nf 0 nf Applications information

20 Applications information 4. Mode selection The three operating modes of the are set by the two inputs, STBY (pin 0) and MUTE (pin ). Standby mode: all circuits are turned off, very low current consumption. Mute mode: inputs are connected to ground and the positive and negative PWM outputs are at 50% duty cycle. Play mode: the amplifiers are active. The protection functions of the are enabled by pulling down the voltages of the STBY and MUTE inputs shown in Figure 0. The input current of the corresponding pins must be limited to 00 µa. Table 7. Mode settings Mode STBY MUTE Standby L () Mute H () L Play H H. Drive levels defined in Table 6: Electrical specifications on page 8 X (don t care) Figure 0. Standby and mute circuits 0 V 0 V Standby 3.3 V R C7 30 kω. µf Mute 3.3 V R4 C5 30 kω. µf STBY MUTE Figure. Turn on/off sequence for minimizing speaker pop VCC 0 STBY 0 MUTE 0 Input 0 t t t t I q Output 0 t Standby Mute Play Mute Standby 0 t 0/8 Doc ID 607 Rev 8

21 Applications information 4.3 Gain setting The gain of the is set by the two inputs, GAIN0 (pin 30) and GAIN (pin3). Internally, the gain is set by changing the feedback resistors of the amplifier. Table 8. Gain settings GAIN0 GAIN Nominal gain, G v (db) L L 5.6 L H 3.6 H L 35.6 H H Input resistance and capacitance The input impedance is set by an internal resistor Ri = 60 kω (typical). An input capacitor (Ci) is required to couple the AC input signal. The equivalent circuit and frequency response of the input components are shown in Figure. For Ci = 470 nf the high-pass filter cutoff frequency is below 0 Hz: f C = / ( π Ri Ci) Figure. Input circuit and frequency response Rf Input signal Ci Input pin Ri Doc ID 607 Rev 8 /8

22 Applications information 4.5 Internal and external clocks The clock of the class-d amplifier can be generated internally or can be driven by an external source. If two or more class-d amplifiers are used in the same system, it is recommended that all devices operate at the same clock frequency. This can be implemented by using one as master clock, while the other devices are in slave mode, that is, externally clocked. The clock interconnect is via pin SYNCLK of each device. As explained below, SYNCLK is an output in master mode and an input in slave mode Master mode (internal clock) Using the internal oscillator, the output switching frequency, f SW, is controlled by the resistor, R OSC, connected to pin ROSC: f SW = 0 6 / ((R OSC 6 + 8) 4) khz where R OSC is in kω. In master mode, pin SYNCLK is used as a clock output pin whose frequency is: f SYNCLK = f SW For master mode to operate correctly then resistor R OSC must be less than 60 kω as given below in Table Slave mode (external clock) In order to accept an external clock input the pin ROSC must be left open, that is, floating. This forces pin SYNCLK to be internally configured as an input as given in Table 9. The output switching frequency of the slave devices is: f SW = f SYNCLK / Table 9. How to set up SYNCLK Mode ROSC SYNCLK Master R OSC < 60 kω Output Slave Floating (not connected) Input Figure 3. Master and slave connection Master Slave ROSC SYNCLK SYNCLK ROSC Output Input Cosc 00 nf Rosc 39 kω /8 Doc ID 607 Rev 8

23 Applications information 4.6 Output low-pass filter To avoid EMI problems, it may be necessary to use a low-pass filter before the speaker. The cutoff frequency should be larger than khz and much lower than the output switching frequency. It is necessary to choose the L and C component values depending on the loud-speaker impedance. Some typical values, which give a cutoff frequency of 7 khz, are shown in Figure 4 and Figure 5 below. Figure 4. Typical LC filter for a 8-Ω speaker Figure 5. Typical LC filter for a 6-Ω speaker Doc ID 607 Rev 8 3/8

24 Applications information 4.7 Protection functions The is fully protected against overvoltages, undervoltages, overcurrents and thermal overloads as explained here. Overvoltage protection (OVP) If the supply voltage exceeds the value for V OVP given in Table 6: Electrical specifications on page 8 the overvoltage protection is activated which forces the outputs to the high-impedance state. When the supply voltage falls back to within the operating range the device restarts. Undervoltage protection (UVP) If the supply voltage drops below the value for V UVP given in Table 6: Electrical specifications on page 8 the undervoltage protection is activated which forces the outputs to the high-impedance state. When the supply voltage recovers to within the operating range the device restarts. Overcurrent protection (OCP) If the output current exceeds the value for I OCP given in Table 6: Electrical specifications on page 8 the overcurrent protection is activated which forces the outputs to the high-impedance state. Periodically, the device attempts to restart. If the overcurrent condition is still present then the OCP remains active. The restart time, T OC, is determined by the R-C components connected to pin STBY. Thermal protection (OTP) If the junction temperature, T j, reaches 45 C (nominally), the device goes to mute mode and the positive and negative PWM outputs are forced to 50% duty cycle. If the junction temperature reaches the value for T j given in Table 6: Electrical specifications on page 8 the device shuts down and the output is forced to the high-impedance state. When the device cools sufficiently the device restarts. 4.8 Diagnostic output The output pin DIAG is an open drain transistor. When any protection is activated it switches to the high-impedance state. The pin can be connected to a power supply (< 39 V) by a pull-up resistor whose value is limited by the maximum sinking current (00 µa) of the pin. Figure 6. Behavior of pin DIAG for various protection conditions VDD R DIAG Protection logic VDD Restart Restart Overcurrent protection OV, UV, OT protection 4/8 Doc ID 607 Rev 8

25 Package mechanical data 5 Package mechanical data The comes in a 36-pin PowerSSO package with exposed pad up. Figure 7 shows the package outline and Table 0 gives the dimensions. Table 0. Symbol PowerSSO36 EPU dimensions Dimensions in mm Dimensions in inches Min Typ Max Min Typ Max A A a b c D E e e F G H h k 0-8 degrees degrees L M N degrees degrees O Q S T U X Y In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK packages, depending on their level of environmental compliance. ECOPACK specifications, grade definitions and product status are available at: ECOPACK is an ST trademark. Doc ID 607 Rev 8 5/8

26 Package mechanical data h x 45 Figure 7. PowerSSO36 EPU outline drawing 6/8 Doc ID 607 Rev 8

27 Revision history 6 Revision history Table. Document revision history Date Revision Changes -Aug-009 Initial release. 7-Aug Oct Jun-00 4 Updated supply voltage range on page Updated package exposed pad dimension Y (Min) in Table 0 on page 5. Updated first feature on page Updated order code name in Table on page Updated Table 5: Electrical specifications on page 8 Updated Section 3.: Characterization curves on page 3 Removed tables for standby, mute and gain after Figure 9 on page 9. Removed datasheet preliminary status, updated features list and updated Device summary table on page Added Table 5: Recommended operating conditions on page 8 with updated minimum supply voltage. 7-Jan-0 5 Updated applications circuit in Figure 9 on page 9. -Feb-0 6 Updated test circuit for characterizations in Figure 3 on page. 9-Mar-0 7 Updated I OCP in Table 6: Electrical specifications. -Sep-0 8 Updated OUTNA in Table : Pin description list Doc ID 607 Rev 8 7/8

28 Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries ( ST ) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY TWO AUTHORIZED ST REPRESENTATIVES, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. 0 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan - Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America 8/8 Doc ID 607 Rev 8

Description. Order code Operating temp. range Package Packaging

Description. Order code Operating temp. range Package Packaging 100 watt + 100 watt dual BTL class-d audio amplifier Features 100 W + 100 W output power at THD = 10% with R L = 6 Ω and V CC = 36 V 80 W + 80 W output power at THD = 10% with R L = 8 Ω and V CC = 34 V