Wireless WIRELESS. DX70 page 341. DX80 page 336 DX91. 1 Watt Data Radio. Accessories page 344

Transcription

1 Wireless SureCross etworks page 335 Consists of a radio frequency network built around a ateway system controller, one or more remotely located odes and integrated Installs where conduit/wiring is not practical Integrates with existing process and control networks Communicates on secure Frequency Hopping Spread Spectrum (FHSS) protocol Delivers two-way Rx/Tx communications with full acknowledgement Ensures optimal device location and peak RF performance with embedded Site Survey Accommodates or 2.4 Hz ISM frequencies Rated IP67; EMA 6P for challenging environments and outdoor applications Available in models with Class I, Division 2 certification for hazardous locations Features 1 watt data radios for extended range of Modbus networks DX70 ACCESSORIES page 336 Includes a ateway and one or more odes that operate on the same frequency Accommodates any combination of odes and FlexPower odes Offers discrete, analog/discrete, temperature and M-AE odes Directly connects to Modbus RTU, Etheret/IP, Modbus TCP/IP and other industrial protocols DX70 page 341 Bridges one ateway and ode on the same frequency Provides plug-and-play installation with direct mapping between ateway and ode Offers discrete and analog in same unit Provides real-time feedback with built-in signal strength indicator DX91 Certified for use in Class I, Division 2, roup A, B, C, D Hazardous Locations when properly installed in accordance with the ational Electrical Code, the Canadian Electrical Code or applicable local code regulations 1 Watt Radio Wireless industrial device for extending the range of a Modbus network Multi-drop capabilities for connecting multiple devices Transceivers for reliable bidirectional communication between radios Accessories page 344 A wide selection of power supplies for ateways, odes and sensors Modbus RTU slave modules for expanding ateway capacity A complete selection of cables for easy hookup Antennas, cables and accessories for virtually every location challenge More information online at bannerengineering.com 335

2 ACCESSORIES DX70 BRACKETS PAE 374 QD CABLES 4- or 5-pin Euro PAES PAE 361 SureCross Wireless etwork To satisfy the performance demands for reliable sensing and actuation, Banner has reinvented wireless. The SureCross Wireless etwork is the first wireless platform built from the ground up for industry featuring proprietary RF design, power management with battery and solar options, and a host of low-power sensors designed to deliver robust remote monitoring and control capabilities. SureCross offers easy, reliable communication between disparate products and processes in a single scalable and unified platform. Access hard-to-reach locations; install where wiring and conduit are not practical Digital and analog in a single unit Easy to retrofit, expand and relocate as needed Reliable and secure Frequency Hopping Spread Spectrum (FHSS) protocol FlexPower supply options including battery and solar Easy plug-and-play deployment SureCross ateway and ode Possibilities can be tailored to accommodate up to 12 functions per device Open design supports inputs from sensors and devices from Banner and other manufacturers Multiple hard-wired network and protocol options at the ateway make it easy to link to industrial host systems FlexPower devices enable sensing solutions never before possible What types of sensors can be used on a SureCross wireless network? Photoelectric Ultrasonic Contact Closures Capacitive Inductive Thermocouple Pressure Thermistor Distance RTD Level Flow Which communication protocols are supported by SureCross ateways? Modbus RTU Modbus TCP/IP Etheret/IP Configured kits with everything needed to solve many common applications quickly and easily (see page 337). How much is provided by each SureCross ode? Up to 4 Analog I (current, voltage) Up to 4 Analog OUT (current, voltage) Up to 8 Discrete I (sinking, sourcing) Up to 8 Discrete OUT (sinking, sourcing) What types of power options are available? 10 to 30V dc AC options FlexPower supply options: FlexPower Battery Modules FlexPower Solar Modules 336 More information online at bannerengineering.com

3 SureCross Wireless etworks etwork identity and device address rotary switches Menu and configuration push buttons RF link status and communications LEDs antenna that rotates for mounting and positioning versatility DI rail mountable or integral mounting holes for versatile mounting ½ inch PT conduit entrance 5-pin Euro-style quick-disconnect LCD display of device information SureCross Configured Kits Discrete Model Frequency** Icon* K9M6EP1 K9M6ED1 K9M6DP2 K9M6DP4 ateway Modbus Enabled 6 I 6 OUT 4 I 8 OUT 4 I 4 OUT 4 I 4 OUT ode 1 6 I 6 OUT 8 I 4 OUT 2 I 2 OUT 1 I 1 OUT ode mm ode mm mm ode 4 Detailed Dimensions I 2 OUT 1 I 1 OUT I 1 OUT 1 I 1 OUT DX70 ACCESSORIES SureCross Configured Kits Analog Discrete Model Frequency** Icon* K9M6EM1 K9M6MP2 Modbus Enabled ateway Discrete: 4 I 4 OUT Analog: 2 I 4 OUT Discrete: 2 I 2 OUT Analog: 2 I 2 OUT ode 1 Discrete: 4 I 4 OUT Analog: 2 I 2 OUT Discrete: 1 I 1 OUT Analog: 1 I 1 OUT ode Discrete: 1 I 1 OUT Analog: 1 I 1 OUT SureCross Configured Kits FlexPower Model Frequency** Icon* K9M3PE1 K9M3E1 Modbus Enabled ateway Discrete: 2 OUT (sourcing) Discrete: 2 OUT (sourcing) Analog: 2 OUT ode 1 Discrete: 1 I configured for MII-BEAM*** 1 I (sinking) (DX81 FlexPower supply included; provides power for ode and MII-BEAM) Discrete: 2 I (sinking) Analog: 2 I (0-20 ma) dc Switched Power Outputs: Switch Configurable (DX81 FlexPower supply included; provides power for ode and one analog sensor) * = ateway = ode ** For 2.4 Hz frequency, replace 9 with 2 in the model number (example, K2M6EM1). *** Low power MII-BEAM model SM ordered separately (see page 343). Discrete outputs are sourcing unless otherwise noted. Analog outputs are 0-20 ma. More information online at bannerengineering.com 337

4 SureCross ateways, 10 to 30V dc ACCESSORIES DX70 Model 9M6W4P4M2M2 9M6S4P4M2M2 9M6W4P4V2V2 9M6S4P4V2V2 9M6W8P4 9M6S8P4 9M6W4P8 9M6S4P8 9M6W6P6 9M6S6P6 Frequency* Modbus Enabled ateway Discrete: 4 I 4 OUT (sourcing) Analog: 2 I 2 OUT (0-20 ma) Discrete: 4 I 4 OUT (sourcing) Analog: 2 I 2 OUT (0-10V dc) Discrete: 8 I 4 OUT (sourcing) Discrete: 4 I 8 OUT (sourcing) Discrete: 6 I 6 OUT (sourcing) Antenna M6W0P0M4M4 9M6S0P0M4M4 Analog: 4 I 4 OUT (0-20 ma)** M6W6P6Z 9M6S6P6Z M-AE Baseline Function for up to 6 M-AE odes SureCross ateway Pro, 10 to 30V dc P9T6W P9T6S Model Frequency* Protocol Antenna Modbus/TCP (default) or Etheret/IP Expandable Remote Model Functionality Description Housing DX85M4P4M2M2 Discrete: 4 I 4 OUT(sourcing) Analog: 2 I 2 OUT(0-20 ma) Modbus RTU Slave Expansion Modules; used to expand ateway capacity IP67 DX85M6P6 Discrete: 6 I 6 OUT(sourcing) * For 2.4 Hz frequency, replace 9 with 2 in the model number (example, 2M6S4P4M2M2). ** For 0-10V dc analog models, replace M with V in the model number (example, 9M6W0P0V4V4). 338 More information online at bannerengineering.com

5 SureCross odes, 10 to 30V dc Model Frequency* Antenna 9X6W4P4M2M2 9X6S4P4M2M2 Discrete: 4 I 4 OUT (sourcing) Analog: 2 I 2 OUT (0-20 ma) X6W4P4V2V2 9X6S4P4V2V2 9X6W8P4 9X6S8P4 9X6W4P8 9X6S4P8 Discrete: 4 I 4 OUT (sourcing) Analog: 2 I 2 OUT (0-10V dc) Discrete: 8 I 4 OUT (sourcing) Discrete: 4 I 8 OUT (sourcing) DX70 ACCESSORIES 9X6W6P6 9X6S6P6 Discrete: 6 I 6 OUT (sourcing) X6W0P0M4M4 9X6S0P0M4M4 Analog: 4 I 4 OUT (0-20 ma)** SureCross FlexPower odes with Switched Power Outputs Model Frequency* Antenna 9X2W22M2X 9X2S22M2X Discrete: 2 I (sinking) 2 OUT (MOS) Analog: 2 I (0-20 ma) dc Switched Power Outputs: Switch Configurable SureCross FlexPower odes Model Frequency* Antenna 9X2W22T 9X2S22T 9X2W0P0R 9X2S0P0R Temperature: 3 I Thermocouple 1 Integrated Thermistor for cold junction compensation Discrete: 2 I (sinking) 2 OUT (MOS) Temperature: 4 I (3-wire RTD ) * For 2.4 Hz frequency, replace 9 with 2 in the model number (example, 2X6W4P4M2M2). ** For 0-10V dc analog models, replace M with V in the model number (example, 9X6W0P0V4V4). Thermocouple units default to J-type. Other types configurable. RTD units default to 3-wire 100 ohm platinum. Other types available. More information online at bannerengineering.com 339

6 ACCESSORIES DX70 SureCross FlexPower odes Model Frequency* Antenna 9X2W22M4 9X2S22M4 Discrete: 2 I (sinking) 2 OUT (MOS) Analog: 4 I (0-20 ma) X1W0P0Z M-AE with internal battery * For 2.4 Hz frequency, replace 9 with 2 in the model number (example, 2X2S22M4). (cont d) Line-powered vehicle detection sensors are also available (see page 241). eneral SureCross Specifications Power: V dc or V dc low power option Power Consumption: Less than 1.4 W (60 ma) at 24V dc Mounting: #10 or M5 (M5 hardware included) M5 Fasteners Max. Tightening Torque: 0.56 m (5 in lbf) Case Material: Polycarbonate Weight: 0.26 kg (0.57 lb.) Indicators: Two LED, bi-color Switches: Two push buttons Display: Six character LCD Cable lands: Four P-7 type, one 1/2-inch PT type Cable lands Max. Tightening Torque: 0.56 m (5 in lbf) Radio 2.4 Hz Range, with Standard 2dB Antenna: Frequency: Transmit Power: Up to 4.8 kilometers (3 miles)* MHz ISM band 21 dbm conducted Spread Spectrum Technology: Antenna Connector: Antenna Max. Tightening Torque: FHSS (Frequency Hopping Spread Spectrum) Ext. reverse polarity SMA - 50 Ω 0.45 m (4 in lbf) Up to 3.2 kilometers (2 miles)* Hz ISM band 18 dbm conducted, 20 dbm EIRP FHSS (Frequency Hopping Spread Spectrum) Ext. reverse polarity SMA - 50 Ω 0.45 m (4 in lbf) * Depending on the environment and line-of-sight, high gain antennas are available to increase the range. Environmental Rating: EMA 6; IEC IP67** Operating Temperature: -40 to +85 C (electronics); -20 to +80 C (LCD) Operating Humidity: 95% max. relative (non-condensing) Shock and Vibration: IEC and IEC Shock: 30g, 11 milliseconds half sine wave, 18 shocks Vibration: 0.5 mm p-p, Hz ** Please refer to the SureCross Wireless etwork Product Manual, Banner part number , for installation and waterproofing instructions. Connection 5-pin Euro-style quick-disconnect fitting. QD cables included. See page 414. Compliance Models: FCC ID TU - This device complies with FCC Part 15, Subpart C, IC:7044-A Hz Models: FCC ID UE This device complies with FCC Part 15, Subpart C, ETSI/E: In accordance with E : V1.7.1 ( ) IC:7044-A-24 Hookup Diagrams See data sheet for hookup instructions 340 More information online at bannerengineering.com

7 SureCross DX70 Wireless etwork A network includes a ateway and one ode that operate in the same frequency band. or 2.4 Hz frequency models are available to accommodate worldwide communication standards. Models include discrete and analog. Input-to-output mapping is controlled by a configured ateway. Open design supports inputs from sensors and devices made by Banner and other manufacturers. Frequency Hopping Spread Spectrum (FHSS) and Time Division Multiple Access (TDMA) architecture combine to ensure reliable data delivery. Rotary switch for network identity is easy to set and change. ateways and odes require 10 to 30V dc line power. Models with internal or external antennas are available, depending on range. Wiring terminals are accessible without removal from mounting. DX70 ACCESSORIES BRACKETS PAE 374 QD CABLES 4- or 5-pin Euro PAES PAE mm Detailed Dimensions mm SureCross DX70 Wireless etworks or internal antenna that rotates for mounting and positioning versatility 1/2 inch PT conduit entrance etwork identity rotary switch Power indicator DI-rail mountable or integral mounting holes for versatile mounting RF link status LED 60.0 mm More information online at bannerengineering.com 341

8 SureCross DX70, 10 to 30V dc ACCESSORIES DX70 ateway Model ode Model Frequency* Antenna** DX709X6S4P4M2M2 DX709X6S4P8 DX709X6S4P4M2M2 DX709X6S8P4 * For 2.4 Hz frequency, replace 9 with 2 in the model number (example, DX702X6S4P4M2M2). ** For internal antennas, replace S with W in the model number (example, DX709X6W4P4M2M2). Discrete: 4 I 4 OUT (sourcing) Analog: 2 I 2 OUT (0-20 ma) ode Discrete: 8 I 4 OUT (sourcing) ateway Discrete: 4 I 8 OUT (sourcing) SureCross DX70 Specifications eneral Power: V dc or V dc low power option Power Consumption: Less than 1.4 W (60 ma) at 24V dc Mounting: #10 or M5 (M5 hardware included) M5 Fasteners Max. Tightening Torque: 0.56 m (5 in lbf) Case Material: Polycarbonate Weight: 0.26 kg (0.57 lb.) Indicators: Power LED reen/red Signal LED Yellow/Red Switches: Two push buttons Display: Six character LCD Cable lands: Two 1/2-inch PT type Cable lands Max. Tightening Torque: 0.56 m (5 in lbf) Radio 2.4 Hz Range, with Standard 2dB Antenna: Frequency: Transmit Power: Spread Spectrum Technology: Antenna Connector: Antenna Max. Tightening Torque: Up to 4.8 kilometers (3 miles)* MHz ISM band 21 dbm conducted FHSS (Frequency Hopping Spread Spectrum) Ext. reverse polarity SMA - 50 Ω 0.45 m (4 in lbf) Up to 3.2 kilometers (2 miles)* Hz ISM band 18 dbm conducted, 20 dbm EIRP FHSS (Frequency Hopping Spread Spectrum) Ext. reverse polarity SMA - 50 Ω 0.45 m (4 in lbf) * Depending on the environment and line-of-sight, high gain antennas are available to increase the range. Environmental Rating: IEC IP67; EMA 6** Operating Temperature: -40 to +85 C (electronics); -20 to +80 C (LCD) Operating Humidity: 95% max. relative (non-condensing) Shock and Vibration: IEC and IEC Shock: 30g, 11 milliseconds half sine wave, 18 shocks Vibration: 0.5 mm p-p, Hz ** Please refer to the SureCross DX70 data sheet, Banner part number for installation and waterproofing instructions. Compliance Models: FCC ID TU - This device complies with FCC Part 15, Subpart C, IC: 7044A Hz Models: FCC ID UE This device complies with FCC Part 15, Subpart C, ETSI/E: In accordance with E : V1.7.1 ( ) IC: 7044A-24 Hookup Diagram See data sheet for hookup instructions 342 More information online at bannerengineering.com

9 Sensors Optimized for use with FlexPower Systems Sensor Models QT50ULBQ Supply Sensing Voltage Description Mode U-AE Ultrasonic - Range 200 mm to 8 m SM312LPQD FlexPower Polar 3 m MII-BEAM Retro Photoelectric SM312DQD Diffuse 380 mm * sheet is for standard products, contact factory at for supporting literature. Mating cable required (see pages 412 and 415). Mounting Hardware Model BWA-HW-001 BWA-HW-002 Description Output Type Connection * 0 to 10V dc or 4 to 20 ma 5-pin Euro QD Bipolar P/PP Replacement mounting hardware packet Replacement access hardware pack (5 plugs 4 glands) 4-pin Euro QD DX70 ACCESSORIES Power Supplies AC Model PS24W Voltage Supplied Description Connection Housing 24V 500 ma Converts V ac to 24V dc orth America (wall plug) 5-pin Euro QD on-industrial (not sealed) /A FlexPower DX81 DX81P6 FlexPower Battery Module to supply FlexPower ode Module driven by one lithium primary battery** Module driven by six lithium primary batteries 5-pin Euro Pigtail QD IP **Replacement lithium primary battery model number is BWA-BATT-001 Antennas Antennas Description Frequency BWA-9Y6-A 6.5 dbd, Yagi, Female MHz BWA-9Y10-A 10.0 dbd, Yagi, Female MHz BWA-9O6-A 6.0 dbd, Fiberglass, Omni, Female MHz BWA-9O5-B 5.0 dbd/7.2 dbd Omni, with ground plate, Female MHz Cables Description Length BWC-1MRSM2 LMR200, RSMA to Male 2 m BWC-1MRSFRSB4 R58, RSMA to RSMAF Bulkhead 4 m BWC-4MF6 LMR400, Male to Female 6 m BWC-4MF15 LMR400, Male to Female 15 m Lightning Protectors Description Frequency BWC-LFBM Bulkhead Lightning Suppressor, type 2.4 Hz Reference uide More information online at bannerengineering.com 343

10 ACCESSORIES DX70 Wireless Accessories Cables page 412 Quick-disconnect cordsets for ateways, odes, Expandable Remote, FlexPower devices, sensors and indicators Single-ended and double-ended cordsets A variety of lengths with rightangle or straight connectors Cordsets available for interfacing antennas Power Supplies page 343 Power supplies for ateways, odes and sensors Models for converting ac voltage to dc FlexPower supplies with solar and battery options for FlexPower odes Brackets page 374 DI-mount bracket for SureCross models Hardware for mounting to housing Black ABS thermoplastic Antennas page 343 Omni and Yagi antenna models for increasing the range of SureCross wireless networks Antenna extension and adapter cables for remote mounting options 344 More information online at bannerengineering.com