44.5 mm mm. Long-range Models. 2 m. 5-pin Mini QD. Q45UBB63DAQ6 20, 40, 160 or 640 ms Q45UBB63DAC Yes. 5-pin Euro QD.

Transcription

1 SENSORS ACCESSORIES LIGHT GAUGING ULTRASONIC MEASURING ARRAYS RADAR U-GAGE QU Flexible Ultrasonic Push-button TEACH programming makes it easy to set the near/far limits of the sensing window. Available ranges are to mm for the short-range models and. to. m for the long-range models. Bipolar discrete models have switches for ON/OFF presence detection and HIGH/LOW level control. - In ON/OFF mode, detects either when the target is within the set range or when it is outside the range. - In HIGH/LOW mode, detects when the target is outside the configured range, for fill level control, web tensioning control and similar applications. time is programmed with switches in discrete models and with a potentiometer in analog models. For remote programming, analog models can be wired directly to an external switch, controller or computer to set window limits ideal for inaccessible applications such as roll diameter detection for overhead cranes. 6. mm. mm Program storage cards After you set up window limits, you can store the limits on circuit cards with non-volatile memory for fast setup. Just store the settings from any QU sensor on the QUML card, and then transfer the settings to any QU sensor with the same available sensing range mm. mm 79. mm online AUTOCAD, STEP, IGES & PDF. mm 87.6 mm Short-range Long-range U-GAGE QU Discrete, -V dc Compensation Connection m QUBB6DA No QUBB6DAQ mm -. m Programmable for Bipolar QUBB6DAQ6,, 6 m NPN/PNP or 6 ms QUBB6DAC Yes QUBB6DACQ QUBB6DACQ6 Connection options: A model with a QD requires a mating cordset (see ). For 9 m cable, add suffix W/ to the m model number (example, QUBB6DA W/). Courtesy of Steven Engineering, Inc.- Ryan Way, South San Francisco, CA Main Office: (6) 88-9-Outside Local Area: (8) 8-9-

2 U-GAGE QU Discrete, -V dc Compensation mm - m Yes Connection m (cont d) Bipolar NPN/PNP Programmable for, 8, or 8 ms QUBB6BC QUBB6BCQ QUBB6BCQ6 Photoelectrics Special Purpose Measurement & Inspection Vision Wireless Lighting & Light Screens U-GAGE QU Analog, -V dc Laser Scanners Systems mm -. m Yes mm - m Yes Compensation Connection * m m Selectable to V dc or to ma Adjustable from to 8 ms Adjustable from 8 to 6 ms QULIU6ACR QULIU6ACRQ QULIU6ACRQ6 QULIU6BCR QULIU6BCRQ QULIU6BCRQ6 Controllers & Modules Two-Hand Control Modules Interlock Switches Emergency Stop & Stop Control ACCESSORIES Connection options: A model with a QD requires a mating cordset (see ). For 9 m cable, add suffix W/ to the m model number (example, QUBB6DA W/). The far limit may be extended as far as.9 m for good acoustical targetshard surfaces with area greater than cm. U-GAGE QU Specifications Sensing Short : Near limit: mm min. Long : Near limit: mm min. Short : Far limit:. m max. Long : Far limit:. m max. LIGHT GAUGING ULTRASONIC QTU S8U QS8U TU/TUX MU T8U QU QUR MEASURING ARRAYS RADAR NOTE: The far limit may be extended on long range units, as far as.9 m for good acoustical targets (hard surfaces with area greater than cm ) Supply Voltage and Current Discrete: to V dc (% max. ripple); ma (exclusive of load) Analog: to V dc (% max. ripple); ma (exclusive of load) Ultrasonic Frequency Long : 8 khz Short : khz Supply Protection Circuitry Protection Circuitry Configuration Ratings Protected against reverse polarity and transient voltages. Protected against false pulse on power-up and continuous overload or short-circuit of outputs. Discrete: Bipolar: One current sourcing (PNP) and one current sinking (NPN) open-collector transistor. Analog: One voltage sourcing and one current sourcing; one or the other output is enabled by internal programming switch #. Discrete: ma max. (each) OFF-state leakage current: less than µa at V dc ON-state saturation voltage: less than.v at ma; less than.v at ma Analog: Voltage sourcing: to V dc, ma max. Current sourcing: to ma, to Ω impedance Courtesy of Steven Engineering, Inc.- Ryan Way, South San Francisco, CA Main Office: (6) 88-9-Outside Local Area: (8) 8-9-

3 LIGHT GAUGING ULTRASONIC MEASURING ARRAYS RADAR SENSORS U-GAGE QU Specifications (cont d) Performance Specifications Short Long Analog resolution or discrete repeatability: ±.% of sensing distance ±.% of sensing distance (±. mm min.) (±. mm min.) Analog Linearity: % of full scale % of full scale effect:.% of sensing distance/ C with temp. comp..% of sensing distance/ C.% of sensing distance/ C without temp. comp. Min. window size: mm mm Hysteresis (discrete output): mm mm Effective Beam See EBPC- to EBPC- on. Adjustments The following may be selected by a -position DIP switch. Discrete: Switch : normally open/normally closed (pump in/pump out) Switch : High/Low level control mode or on/off presence sensing mode Switch & : speed selection (digital filter) Analog: Switch : slope positive or output slope negative Switch : Current output mode or voltage output mode Switch : Loss of echo min/max mode or loss of echo Hold Mode Switch : Loss of echo min/max default output value Discrete: Three status LEDs: Green: power ON Yellow: outputs are conducting (Yellow LED also indicates programming status during setup mode) Red: indicates relative strength of received echo Analog: Three status LEDs: Green: power ON Yellow: target is sensed within the window limits (Yellow LED also indicates programming status during setup mode) Red flashing: indicates relative strength of received echo -segment moving dot LED indicates the position of the target within the sensing window. See data sheet for detailed information. Construction Environmental Rating Molded PBT polyester thermoplastic polyester housing, o-ring sealed transparent acrylic top cover, and stainless steel hardware. QU sensors are designed to withstand psi washdown. The base of cabled models has a ½"-NPS internal conduit thread. Leakproof design is rated IEC IP67; NEMA 6P Connections m or 9 m attached cable, or -pin Mini-style or -pin Euro-style QD fitting. QD cordsets are ordered separately. See s. Operating Conditions : - to 7 C Relative humidity: % Vibration and Mechanical Shock All models meet Mil. Std. F requirements. Method A (Vibration: to 6Hz max., double amplitude.6", maximum acceleration G). Method B conditions H & I (Shock: 7G with unit operating; G for non-operation). Also meets IEC 97-- requirements: G, milliseconds duration, half sine wave. Application Notes Short : Min. target size: x mm aluminum plate at mm x mm aluminum plate at. m Long : Min. target size: x mm aluminum plate at m Discrete: Enable/Disable; Connect yellow wire to to V dc to enable sensor and to V dc to disable sensor. When the sensor is disabled, the last output state is held until the sensor is re-enabled. The wire must be held to the appropriate voltage for at least milliseconds for the sensor to enable or disable. Certifications Hookup Diagrams MI8 (p. 76) Courtesy of Steven Engineering, Inc.- Ryan Way, South San Francisco, CA Main Office: (6) 88-9-Outside Local Area: (8) 8-9-

4 Cordsets Length Euro QD (With Shield) See 687 Threaded -Pin Straight Right-Angle m MQDEC-6 MQDEC-6RA m MQDEC- MQDEC-RA 9 m MQDEC- MQDEC-RA Additional cordset information available. See 679. Mini QD (With Shield) Length See 7 Threaded -Pin Straight m MBCC-6 m MBCC- m MBCC- Brackets QU pg. 69 pg. 6 pg. 6 SMBA SMBMM SMBSC Additional bracket information available. See 6. Photoelectrics Special Purpose Measurement & Inspection Vision Wireless Lighting & Light Screens Laser Scanners Systems Controllers & Modules Two-Hand Control Modules Interlock Switches Effective Beam Patterns Emergency Stop & Stop Control QU Short with Rod Target (Typical) QU Short with Plate Target (Typical) mm mm ø mm Rod mm ø mm Rod mm mm mm mm mm 6 mm 8 mm mm mm mm mm mm x mm Plate mm x mm Plate mm mm mm mm mm 6 mm 8 mm mm mm mm LIGHT GAUGING ULTRASONIC QTU S8U QS8U TU/TUX MU T8U QU QUR MEASURING ARRAYS RADAR EBPC- EBPC- QU Long with mm Rod Target (Typical) QU Long with x mm Plate Target (Typical) mm mm mm mm mm mm mm mm mm mm mm mm mm mm mm mm mm mm mm mm mm mm mm mm mm mm mm mm mm mm mm mm EBPC- EBPC- Courtesy of Steven Engineering, Inc.- Ryan Way, South San Francisco, CA Main Office: (6) 88-9-Outside Local Area: (8) 8-9-

5 HOOKUPS WIRING DIAGRAMS REFERENCE CHARTS GLOSSARY INTERNATIONAL REPS Measurement and Inspection Hookups MI7 MU Receiver MI8 QU & QUR with Discrete s REFERENCE -V dc High Speed (-V dc) Normal Speed (-V dc) * It is recommended that the shield wire be connected to either earth ground or DC common. = Brown = White = Blue = Black = Gray Shield** -V dc NOTE: Gray/Yellow wires on QU models used for enable. ** It is recommended that the shield wire be connected to either * Remote -V dc Programming earth ground or DC common. QU & QUR with Analog s * - ma -V Remote Teach -V dc -V dc NOTE: Gray/Yellow wires on QU models used for enable. ** It is recommended that the shield wire be connected to either earth ground or DC common. -Pin Euro = Brown = White = Blue = Black = Gray -Pin Mini = Brown = White = Blue = Black = Yellow* -Pin Euro QD Shield** -Pin Euro -Pin Mini MI9 T8U Current Sinking (NPN) NORMAL Resolution MI T8U Current Sourcing (PNP) NORMAL Resolution -V dc -V dc T8U Current Sinking (NPN) HIGH Resolution -V dc = Brown = White = Blue = Black T8U Current Sourcing (PNP) HIGH Resolution -V dc = Brown = White = Blue = Black -Pin Euro -Pin Euro Courtesy of Steven Engineering, Inc.- Ryan Way, South San Francisco, CA Main Office: (6) 88-9-Outside Local Area: (8)