Product Brochure MS8911B. Digital Broadcast Field Analyzer 100 khz to 7.1 GHz MS8911B-030. ISDB-T Analysis Software

Transcription

1 Product Brochure MS8911B Digital Broadcast Field Analyzer 100 khz to 7.1 GHz MS8911B-030 ISDB-T Analysis Software

2 The Digital Broadcast Field Analyzer features a high-performance signal-analyzer function in a compact battery-operated unit. This instrument is very useful for survey and maintenance of digital broadcast signal waves in the field. Shift key Esc key Function Hard Keys Soft Keys Ethernet Connector USB Flash Drive Connector Compact Flash Memory Card Slot External Power USB Interface: To be connected to PC 2 External Trigger Fan Exhaust Port Input 10 MHz External RF In Headset Jack Reference Input

3 MS8911B Digital Broadcast Field Analyzer MS8911B-030 ISDB-T Analysis Software On/Off Button High-Performance Handheld Spectrum Analyzer This analyzer has a high performance spectrum analyzer from 100 khz to 7.1 GHz. Directional Buttons Rotary Knob Digital Broadcast Waveform Measurement Many functions, such as field strength measurement, modulation signal analysis (MER measurement/ Constellation monitor) and spectrum mask measurement, are incorporated in this instrument to support coverage area surveys and field maintenance of digital broadcast waves. Easy-of-Use Anritsu focused easy use by eliminating troublesome condition setting and operation settings so even beginners can operate this instrument simply and easily. Code (+/ ) Key Keypad Enter Key Back Key Joint development by NHK & NHK Integrated Technology Inc. 3

4 Compact High-Performance Spectrum Analyzer Function The MS8911B digital broadcast field analyzer features a high-performance spectrum analyzer function supporting 100 khz to 7.1 GHz as standard equipment in a compact battery-operated unit. For Measurement at R&D and Manufacturing This field analyzer has a full range of functions like sweep span, sweep trigger, resolution bandwidth and video bandwidth. It can be used as a high-performance spectrum analyzer for R&D and manufacturing. Also, because it is battery operated, the side-band noise of the power line can be measured (Figure 2). For Field Use Figure 2: Measurement of Side-band Noise of Power Line The MS8911B wide-range function shorten field measurement times, while covering a wide range of frequencies and signal level (Figure 1). Users can save measured data to internal memory. Figure 1: Simultaneous Measurement of Both Small Signals and Carriers Other Features High-speed sweeping (900 ms: full-band, 50 µs: Zero Span) Maximum input level: +43 dbm (20 W) Drawing standard line Multi-marker Noise marker counter marker (The frequency of the set marker point can be read with 1-Hz resolution) One-touch measurement function (channel power 1, field strength 1, occupied frequency bandwidth, adjacent channel leakage power, C/I: carrier vs. interference) AM/FM Demodulation function External control tool (external control software with Ethernet or USB) Local language support (English, Japanese, French, German, Italian, Korean, Chinese, Spanish) 1: Method with spectrum measurement 4

5 Digital Broadcast Wave Measurement MS8911B-030 ISDB-T Analysis Software MS8911B-030 ISDB-T analysis software analyzes various the signals in terrestrial digital broadcasts (ISDB-T). This is very useful for surveying terrestrial digital broadcast coverage and for installing and maintaining ISDB-T equipment. Measurement and Test Items Terminal voltage, channel power and field strength Delay profile MER, constellation monitor, frequency measurement Transmission spectrum mask adaptability test, occupied frequency bandwidth Spurious Phase-noise Detection of transmission parameter (Mode, GI, TMCC information) Delay Profile Measurement This function measures the difference in the timing and level of multi-path signals caused by reflection or diffraction. By measuring the in-channel frequency response, the impact of multi-path and frequency selective fading can be observed. This is useful for adjusting the delivery timing of the network relaying the broadcast wave. Terminal Voltage/ Power, Field Strength Measurement By using digital signal processing technique (DSP), the user can measure terminal voltage, CH power and field strength (dbµv/m) with accurately converted antenna factor. Values can be measured for 13 segment or for only 1 segment at the center of 13 segments. The measurement result is displayed as a bar graph and the high-visibility display is ideal for adjusting the optimum reception antenna angle. Delay Profile Measurement Field Strength Measurement 5

6 MER/Constellation/ Measurement The MER measurement function, which evaluates the modulation signal quality of digital broadcast wave directly and quantitatively, is essential for managing signal margin, and equipment aging deterioration and for maintaining a stable broadcast service. The constellation monitor function is useful for analyzing the condition of the received signal by monitoring the modulation symbol movement. Moreover, this function measures the center frequency in the OFDM modulation status very accurately, using advanced DSP. Using these features, broadcast frequencies can be monitored while broadcasting is serviced. Spurious Measurement Using the spurious measurement function, spurious frequency, absolute level, and relative level can be displayed together. Spurious Measurement MER/ Constellation/ Measurement Transmission Spectrum Mask Adaptability Test/ Occupied Bandwidth Measurement The adaptability of the transmission spectrum mask ARIB STD B31-compliant can be tested. Together with this, the user can measure the occupied bandwidth and calculate the safety margin of the spectrum waveform for the standard line and its frequency position. Phase Noise Measurement/ Measurement of Deflection and CW Wave This instrument can measure the phase noise of the CW signal (no modulation), such as at a broadcast station oscillator. Also, the result of integrating the noise power can be output to the phase noise measurement graph. Additionally, the CW wave frequency and frequency deflection can be measured. Phase Noise Measurement Measurement of Transmission Spectrum Mask Adaptability Test 6

7 Easy-of-Use Field measurement is severely limited by time, place and the user s skill level. The MS8911B-030 ISDB-T Analysis Software makes operation easy even for beginners. This instrument has the following three operation modes, supporting every skill level. Easy External Control Control over Ethernet using an external controller is supported, permitting. Automatic measurement or data acquisition. Controller 10BASE-T Crossing cable Ethernet Connector Using presets the operator can analyze each signal just by specifying the broadcast channel to measure. Custom The following software must be installed in the controller. The user can optionally set each measurement condition and analyze each signal by specifying the broadcast channel to measure. Batch The user can specify multiple broadcast channels and measurement items that have been pre-registered. The results are saved to internal memory. Software NI-VISA Application Software Outline National Instruments VISA library. VISA is the measurement tool control communication library controlled by VXIplug & play Systems Allowance. Regardless of the communication media, this is the driver software to control the measurement tool. Get this software from National Instruments. This is the software for programming with Visual Basic and LabVIEW. Saving Measurement Data The measurement screen can be saved in JPEG format to the MS8911B internal memory. Using a compact flash card or USB flash drive, the user can save the data to external memory. By saving the measurement screen, the user can view the measurement conditions and waveform at a glance and also can paste the data into reports. Measurements can be saved in CSV format, too. Batch Measurement 7

8 Specifications MS8911B Digital Broadcast Field Analyzer Amplitude Range Tuning Range Tuning Resolution Reference Span Span Accuracy Sweep Time Sweep Time Accuracy Sweep Trigger 100 khz to 7.1 GHz 9 khz to 7.1 GHz 1 Hz 10 MHz Aging: ±0.1 ppm/ year Accuracy: ±0.1 ppm (25 C ±25 C) + long-term drift 10 Hz to 7.1 GHz + 0 Hz (zero span) Same as frequency reference accuracy Min. 100 ms, 10 µs in zero span ±2% in zero span Free Run, Single, Video, External Resolution Bandwidth ( 3 db width) 10 Hz to 3 MHz in 1-3 sequence ±10%, 8 MHz demodulation bandwidth Video Bandwidth ( 3 db) 1 Hz to 3 MHz in 1-3 sequence SSB Phase Noise 100 dbc/hz max. at 10, 20 and 30 khz offset from carrier 102 dbc/hz max. at 100 khz offset from carrier Measurement Range DANL to +30 dbm Absolute Amplitude Accuracy 100 khz to 10 MHz ±1.5 db Power Levels 50 dbm, <35 db >10 MHz to 4 GHz ±1.25 db Input Attenuation, Preamp Off >4 to 7.1 GHz ±1.75 db 50 db: 0.05 to 0.75 GHz Second Harmonic Distortion 40 db: >0.75 to 1.05 GHz (0 db input attenuation, 50 db: >1.05 to 1.4 GHz 30 dbm input) 70 db: >1.4 to 2 GHz 80 db: >2 GHz Typ. 50 to 300 MHz >8 dbm Third Order Intercept (TOI) >300 MHz to 2.2 GHz >10 dbm (Preamp Off) >2.2 to 2.8 GHz >15 dbm >2.8 to 4.0 GHz >10 dbm >4.0 to 7.1 GHz >13 dbm Preamp On Preamp Off Typ. Max. Typ. Max. Displayed Average Noise Level >10 MHz to 1 GHz DANL in 10 Hz RBW, 0 db >1 to 2.2 GHz Attenuation Reference Level >2.2 to 2.8 GHz dbm >2.8 to 4.0 GHz >4.0 to 7.1 GHz dbm Typ. Noise Figure (derived from DANL >10 MHz to 1 GHz 11 db measurement) 0 db Attenuation, >1 to 2.2 GHz 14 db Reference Level 50 dbm, 23 C, >2.2 to 2.8 GHz 18 db Preamp On >2.8 to 4.0 GHz 14 db >4.0 to 7.1 GHz 16 db Display Range 1 to 15 db/div in 1 db steps. Ten divisions Amplitude Units Attenuator Range Attenuator Resolution Input Related Spurious Exceptions: Input 1674 MHz >1674 to 1774 MHz Log-scale modes: dbm, dbv, dbmv, dbµv Linear-scale modes: nv, µv, mv, V, kv, nw, µw, mw, W, kw 0 to 65 db 5 db steps 60 dbc max., (< 70 dbc typ.), 30 dbm input, 0 db RF attenuation) Spurious level 46 dbc max. ( 56 dbc typ.), 0 to 2800 MHz 50 dbc max. ( 60 dbc typ.), at F input 1674 MHz 8

9 Amplitude General Residual Spurious, Preamp Off 90 dbm max., 100 khz to <3200 MHz (RF Input Terminated, 0 db RF 84 dbm max., 3200 khz to 7100 MHz Attenuation) Exceptions Spurious level 250, 300 and 350 MHz 85 dbm max. to 4010 MHz 80 dbm max. ( 90 dbm typ.) to 5084 MHz 70 dbm max. ( 83 dbm typ.) to 5894 MHz 75 dbm max. ( 87 dbm typ.) to 7028 MHz 80 dbm max. ( 92 dbm typ.) Residual Spurious, Preamp On 100 dbm max. (RF input terminated, 0 db RF attenuation) RF Input VSWR 2.0:1 max., 1.5:1 typ. (10 db attenuation) Maximum Continuous Input Input Damage Level ESD Damage Level External Standard Display Languages Marker Modes Sweeps Detection Memory Traces Interfaces Size and Weight Environmental Safety Electromagnetic Compatibility 10 db attenuation, +30 dbm 10 db attenuation, >+43 dbm, ±50 Vdc <10 db attenuation, >+23 dbm, ±50 Vdc Input protection relay opens at >30 dbm with 10 db input attenuation and approx. 10 to 23 dbm with <10 db attenuation >10 kv 10 db attenuation 1, , 1.544, 2.048, , 4.8, , 5, , 10, 13, MHz, Input level: 10 to +10 dbm Bright, Color, Transmissive LCD, Full SVGA, 8.4 inches English, Spanish, French, German, Japanese, Chinese, Italian and Korean Six markers, seven modes: Normal, Delta, Marker to Center, Marker to Reference Level, Next Peak Left, Next Peak Right, All Makers Off, Noise Marker, Counter Marker (1 Hz resolution) Full span, Zero span, Span up/span down in increments Peak, Negative, Sample, RMS, Quasi peak The internal memory can save more than 1000 measurement setups and more than 1000 traces. The contents of internal memory can be copied to and from a removable compact flash (CF) card. Displayed traces: Three-trace-overlay. One trace is always live data; Two traces can be either stored data or traces that have been mathematically manipulated. Type-N female RF connector BNC Female connectors for external frequency reference and external trigger Mini-B USB 2.0 for data transfer to PC A-type USB flash drive connector to USB flash drive RJ45 Connector for Ethernet 10/100BASE-T 2.5 mm 3-wire headset connector 313 x 211 x 77 mm, <2.9 kg typ. MIL-PRF-28800F Class 2 Operating: 10 to +55 C, humidity 85% max. Storage: 51 to +71 C Conforms to EN for Class 1 portable equipment Meets European Community requirements for CE marking 9

10 MS8911B-030 ISDB-T Analysis Software Electrical Characteristic Setting Field Strength, Terminal Voltage, Power These specifications are based on when the MS8911B-030 is installed in the MS8911B. For performance specifications, each value is assumed to be obtained from measurement after a 10-minute warmup at a constant ambient temperature. Range Map Mode Guard Interval Modulation System Combination of Mode and Guard Interval 35 to 800 MHz (signal frequency) UHF IF (37.15 MHz) None (optional frequency setting) Range: 13 to 62 channels N-channel center frequency = (N-13) x Mode 2, Mode 3 Manual setting, or setting by automatic detection 1/4, 1/8, 1/16 Manual setting, or setting by automatic detection QPSK, 16 QAM, 64 QAM Manual setting, or setting by automatic detection Mode, Guard Interval 1/4 1/8 1/16 Mode 2 OK OK None Mode 3 OK OK OK On, Off Spectrum Reverse Partial Reception Recognized when segment at A layer is 1 Can specify start position where data picked out for signal analysis Can pick up data for valid symbol length from position including guard interval for FFT Start position N/8 x guard interval length Originates from valid symbol start n: 0 to 8 Maximum Input Level Reference Level Range ISDB-T Signal, 1 Input Level Graph Correction Table for Field Strength Measurement +20 dbm (Preamp: Off) 10 dbm (Preamp: On) +20 to 25 dbm/5 db steps (Preamp: Off) 10 to 50 dbm/10 db steps (Preamp: On) Setting range: 13 to 62 channels Setting resolution: 1 Hz Setting range: 35 to 800 MHz Setting resolution: 1 Hz Input level range: +20 dbm to noise floor (Preamp: Off), 20 dbm to noise floor (Preamp: On) Measurement resolution: 0.1 db Measurement accuracy: 13 to 62 channels, Average count: 10, VSWR for measurement under 1.5, 50 W Preamp: Off ±2.0 db (+20 to 10 dbm, typ.) ±2.0 db ( 10 to 60 dbm) Preamp: On ±2.0 db ( 20 to 84 dbm) Display average noise level: 13 to 62 channels, 5.6 MHz width RF Input: 50 W terminal, Average count: 50, +20 to +30 C 70 dbm (Preamp: Off), 94 dbm (Preamp: On) 1 db Compression level 13 to 62 channels, built-in attenuator: 0 db, CW 15 dbm (Preamp: Off), 43 dbm (Preamp: On) Units: dbm, dbµv, dbµv[emf], dbµv/m Termination voltage [dbµv] displayed as bar chart Level correction data table for measuring field strength saved in instrument Impedance 50 Ω, 75 Ω (External impedance converter for 75 Ω) Measurement Mode Single, Continuous, Average, Moving average, Max hold Average count: 1 to

11 Constellation, MER, Delay Profile Response ISDB-T Signal, 1 Input Setting range: 13 to 62 channels, Setting resolution: 1 channel Setting range: 35 to 800 MHz, Setting resolution: 1 Hz Lock Range ± 90 khz Input level range: +20 dbm to noise floor +20 db (Preamp: Off) Level 20 dbm to noise floor +20 db (Preamp: On) Display item: Total, A layer, B layer, C layer, TMCC, AC1 Display resolution: 0.1 db Residual MER: Total, 13 to 62 channels, Mode 3 Guard Interval: 1/8, 64 QAM, average count 10 Internal attenuator: 0 db, typ. MER 42 db (Preamp: Off, Reference level: 20 dbm, 20 dbm input) 37 db (Preamp: On, Reference level: 50 dbm, 50 dbm input) Interference wave effect: Total, 13 to 62 channels, Mode 3, Guard Interval: 1/8, 64 QAM, average count 10 ±2 channels, 0 dbm interference wave for expected wave, typ.: 30 db (Preamp: Off, 35 dbm) Constellation Display items: A layer, B layer, C layer, TMCC Measures center frequency of modulation signal Units: Hz, ppm Display resolution: 0.1 Hz Accuracy: 20 dbm, MER >40 db, Preamp: Off, average count: 10, Mode 3, guard interval: 1/8, 64 QAM, ± (measurement frequency x reference frequency accuracy) ±0.3 Hz Single, Continuous, Average, Moving average, Overwrite (Constellation only) Measurement Mode Average count: 1 to 100 ISDB-T Signal, 1 Input Setting range: 13 to 62 channels, Setting resolution: 1 channel Setting range: 35 to 800 MHz, Setting resolution: 1 Hz Lock Range ±90 khz Input level range: +20 dbm to noise floor +20 db (Preamp: Off) Level 20 dbm to noise floor to +20 db (Preamp: On) Horizontal axis (Delay time): Max. level signal displayed as 0 µs Display range Whole graph: (1/24 of valid symbol length) to (7/24 of valid symbol length) Enlarged graph: 24.6 µs width of optional whole graph Valid Range: 0 µs to Guard Interval length Delay Profile Graph Resolution: 0.12 µs Vertical axis (level) Display range: 5, 10, 25, 50 db Display resolution: 0.1 db Marker: Delay time, Assumed distance and Relative level read with marker function Single, Continuous, Average, Moving Average (only numeric value) Measurement Mode Average count: 1 to 100 ISDB-T Compliant OFDM Wave, 1 Wave Input Setting range: 13 to 62 s, Setting resolution: 1 channel Setting range: 35 to 800 MHz, Setting resolution: 1 Hz Lock Range ± 90 khz Input level range: +20 dbm to noise floor + 20 db (Preamp: Off) Level 20 dbm to noise floor + 20 db (Preamp: On) Horizontal axis: Displays, centered around carrier frequency () (Carrier set to 0 Hz) Display range: ±2.785 MHz Valid range: ±2.74 MHz (Mode 2), ±2.76 MHz (Mode 3) Response Graph Display resolution: 1 khz Vertical axis (level): Displays average value of frequency response as 0 db Display range: 5, 10, 25, 50 db Display resolution: 0.1 db Marker: Can read offset frequency and relative level with marker function Measurement Mode Single, Continuous, Average, Moving average Average count: 1 to

12 ISDB-T Compliant OFDM Wave, 1 Wave Input Setting range: s 13 to 62, Setting resolution: 1 channel Level Input level range: +20 to 15 dbm Measurement Mode Single Standard line RBW: 10 khz 0 VBW: 300 Hz Detect: Peak Relative level [db] Spectrum Mask Mask (Standard A) Mask (Standard B) Measurement point number: 4001 points Pass-fail judgment: Determines whether the measurement waveform is compliant with mask standard line and displays its result. When measurement waveform for each frequency is less than standard line, the result is judged to have passed. Safety margin: Displays frequency and the minimum value of the difference between the measured waveform and mask standard line among each break point of the mask standard line. Floor reduction function: Deducts the MS8911B floor noise from the measured spectrum waveform and displays its result. Marker function: Relative level and offset frequency of measurement waveform can be read. Occupied frequency bandwidth: Displays the frequency bandwidth, where 99% of the total power is within the range of ±10 MHz of the stay focus. Display resolution: 0.01 MHz Standard line RBW: 10 khz VBW: 300 Hz Detect: Peak Measurement point number: 6001 points Pass-fail judgment: Determines whether the measurement waveform is compliant with mask standard line and displays its result. When measurement waveform for each frequency is less than standard line, the result is judged to have passed. Safety margin: Displays frequency and the minimum value of the difference between the measured waveform and mask standard line among each break point of the mask standard line. Floor reduction function: Deducts the MS8911B floor noise from the measured spectrum waveform and displays its result. Antenna power: Can be set only when the standard line is greater than 0.25 W and less than or equal to 2.5 W. P: Antenna power When the standard line is less than or equal to 0.25 W, "P <= 0.25 W" is displayed. When the standard line is greater than 0.25 W and less than or equal to 2.5 W, "0.25 W < P 2.50 W" is displayed. When the standard line is greater than 2.5 W, "P > 2.50 W" is displayed. Marker function: Relative level and offset frequency of measurement waveform can be read. Occupied frequency bandwidth: Displays the frequency bandwidth, where 99% of the total power is within the range of ±10 MHz of the stay focus. Display resolution: 0.01 MHz 12 Attenuation [dbc/10 khz] Difference from center frequency of a channel [MHz] Line for P 0.25 W P: Antenna Power Line for 0.25 W<P 2.50 W Line for P >2.50 W Difference from center frequency of a channel [MHz]

13 Phase Noise Spurious Emissions Batch Others ISDB-T Signal, 1 Input Lock Range Level Graph Setting range: 13 to 62 channels, Setting resolution: 1 channel Setting range: 8 to 800 MHz, Setting resolution: 1 Hz ±2 khz Input level range: +20 to 10 dbm Horizontal axis range: 100 Hz to 6 MHz Vertical axis range: 40 to 140 dbc/hz Marker: Can read graph frequency, phase noise and value integrated with phase noise between two optional points Fixed point display: Displays phase noise of offset frequency 1, 10, 100 khz. Displays value integrated with phase noise of 100 Hz to 6 MHz 10 dbm, Average count: 10 Residual Phase Noise 100 dbc/hz (10 khz offset), 102 dbc/hz (100 khz offset) Measurement resolution: 0.01 Hz Measurement accuracy: 10 dbm, Average count: 10 ± (measurement frequency x reference frequency accuracy) ±0.20 Hz Measurement Mode ISDB-T Signal, 1 Input Level Spurious Searching Condition Result Display Single, Continuous, Average Average count: 1 to 100 Setting range: 13 to 62 channels, Setting resolution: 1 channel Input level range: +20 to 0 dbm Search range: 5 MHz to quintupled main signal frequency Without main signal frequency ±9 MHz RBW: 10 khz (5 to 30 MHz), 100 khz (30 MHz to 1 GHz), 1 MHz (1 to 4 GHz) Detection mode: RMS Two measurement methods: 5 MHz to 1 GHz, and 1 GHz or more (main signal frequency x 5) HPF required to drop main signal for measuring 1 GHz or more (Main signal frequency x 5) Displays frequency, Absolute level, Relative level, RBW, and Detection mode for five spurious with larger level Measurement Mode Single Specifies measurement item and several channels for continuous measurement, and saves each measurement result to JPEG file Setting range: 13 to 62 channels, Maximum channel number: 10 channels Measurement Items Reference Save the Measurement Results Save Recall of Setting Information Display Language Field strength, power, MER, error, Spectrum mask evaluation, Occupied frequency bandwidth : 10 MHz, Level: 10 to +10 dbm JPEG file for measurement screen and CSV file for numerical data (except graph data) saved to in internal memory and measurement results in memory copied to external memory Saves panel setting to internal memory Recalls saved panel setting English or Japanese 13

14 Ordering Information Please specify the model/order number, name and quantity when ordering. The following name of articles is an order name. The actual name may differ name from the product. Model/Order No. Name Main Frame MS8911B Digital Broadcast Field Analyzer Standard Accessories W2819AE MS8911B Operation Manual Soft Carrying Case Master Software Tools Program CD-ROM Rechargeable Battery, Li-Ion AC-DC Adapter Automotive Cigarette Lighter/12 Volt DC Adapter Tilt Bail Accessory USB Cable (A-mini B) Ethernet Cable 7 feet (213 cm) MB Compact Flash Memory Adapter, N (m) to SMA (f), 50 Ω Adapter, N (m) to BNC, 50 Ω Option (Hardware) MS8911B-057 DVB-T/H BER Unit MS8911B-157 DVB-T/H BER Unit Retrofit Option (Software) MS8911B-030 ISDB-T Analysis Software MS8911B-032 ISDB-T SFN Field Measurement Software MS8911B-132 ISDB-T SFN Field Measurement Software Retrofit MS8911B-050 DVB-T/H Analysis Software MS8911B-052 DVB-T/H SFN Field Measurement Software MS8911B-152 DVB-T/H SFN Field Measurement Software Retrofit Model/Order No. Name Optional Accessories W2834AE MS8911B-030 Operation Manual W2835AE MS8911B-030 Remote Control Manual W2903AW MS8911B-032 Operation Manual (Japanese) W2833AE MS8911B-050 Operation Manual W2904AE MS8911B-052 Operation Manual 42N50A-30 Attenuator [30 db, 50 W, Bi-directional, DC to 18 GHz, N (m)-n (f)] 15NNF50-1.5C Test Port Cable Armored 1.5 m [N (m)-n (f), 6 GHz] J0576D Coaxial Cord (N), 2 m J0127C Coaxial Cord (BNC), 0.5 m J0127A Coaxial Cord (BNC), 1 m MP640A Coaxial Cord (DC to 1700 MHz) MP721A Attenuator (3 db, DC to 12.4 GHz) MP721B Attenuator (6 db, DC to 12.4 GHz) MP721C Attenuator (10 db, DC to 12.4 GHz) MP721D Attenuator (20 db, DC to 12.4 GHz) MP721E Attenuator (30 db, DC to 12.4 GHz) MA1621A 50 Ω to 75 Ω Impedance Converter (Insertion loss: 1.9 db, 25 Ω resistance, I/O: N type) MA8994A 50 Ω to 75 Ω impedance converter (Insertion loss: 1.9 db, 25 Ω resistance, Input: F type, Output: N type) 12N50-75B Impedance Converter N to F [N (m) 50 Ω to N (f) 75 Ω Impedance Converter Insertion loss: 7.5 db, resistance-pad] R MS8911B Transit Case Charger (external charger) MP651A Dipole Antenna (470 to 1700 MHz, S-5DWPL, 5D-2W, S-5DWP, 10 m) MP651B Dipole Antenna (470 to 1700 MHz, N-LP-55U, RG-55/U, N-P-55U, 10 m) MP635A Log-Periodic Antenna (80 to 1000 MHz) MP666A Log-Periodic Antenna (200 to 2000 MHz) R USB Flash Drive Soft Carrying Case Soft Carrying Case (With Cover Open) Rechargeable Battery, Li-Ion Tilt Bail Accessory 14

15 Note: 15

16 Specifications are subject to change without notice. Anritsu Corporation Onna, Atsugi-shi, Kanagawa, Japan Phone: Fax: U.S.A. Anritsu Company 1155 East Collins Blvd., Suite 100, Richardson, TX 75081, U.S.A. Toll Free: Phone: Fax: Canada Anritsu Electronics Ltd. 700 Silver Seven Road, Suite 120, Kanata, Ontario K2V 1C3, Canada Phone: Fax: Brazil Anritsu Eletrônica Ltda. Praca Amadeu Amaral, 27-1 Andar Paraiso-São Paulo-Brazil Phone: Fax: U.K. Anritsu EMEA Ltd. 200 Capability Green, Luton, Bedfordshire, LU1 3LU, U.K. Phone: Fax: France Anritsu S.A. 9 Avenue du Québec, Z.A. de Courtabœuf Les Ulis Cedex, France Phone: Fax: Germany Anritsu GmbH Nemetschek Haus, Konrad-Zuse-Platz München, Germany Phone: Fax: Italy Anritsu S.p.A. Via Elio Vittorini 129, Roma, Italy Phone: Fax: Sweden Anritsu AB Borgafjordsgatan 13, KISTA, Sweden Phone: Fax: Finland Anritsu AB Teknobulevardi 3-5, FI VANTAA, Finland Phone: Fax: Denmark Anritsu A/S Kirkebjerg Allé 90, DK-2605 Brøndby, Denmark Phone: Fax: Spain Anritsu EMEA Ltd. Oficina de Representación en España Edificio Veganova Avda de la Vega, n 1 (edf 8, pl 1, of 8) ALCOBENDAS - Madrid, Spain Phone: Fax: United Arab Emirates Anritsu EMEA Ltd. Dubai Liaison Office P O Box Dubai Internet City Al Thuraya Building, Tower 1, Suit 701, 7th Floor Dubai, United Arab Emirates Phone: Fax: Singapore Anritsu Pte. Ltd. 60 Alexandra Terrace, #02-08, The Comtech (Lobby A) Singapore Phone: Fax: India Anritsu Pte. Ltd. India Branch Office Unit No. S-3, Second Floor, Esteem Red Cross Bhavan, No. 26, Race Course Road, Bangalore , India Phone: Fax: P.R. China (Hong Kong) Anritsu Company Ltd. Units 4 & 5, 28th Floor, Greenfield Tower, Concordia Plaza, No. 1 Science Museum Road, Tsim Sha Tsui East, Kowloon, Hong Kong Phone: Fax: P.R. China (Beijing) Anritsu Company Ltd. Beijing Representative Office Room 1515, Beijing Fortune Building, No. 5, Dong-San-Huan Bei Road, Chao-Yang District, Beijing 10004, P.R. China Phone: Fax: Korea Anritsu Corporation, Ltd. 8F Hyunjuk Building, , Yeoksam Dong, Kangnam-ku, Seoul, , Korea Phone: Fax: Australia Anritsu Pty. Ltd. Unit 21/270 Ferntree Gully Road, Notting Hill, Victoria 3168, Australia Phone: Fax: Taiwan Anritsu Company Inc. 7F, No. 316, Sec. 1, Neihu Rd., Taipei 114, Taiwan Phone: Fax: Please Contact: Printed on 70% Recycled Paper Catalog No. MS8911B-030-E-A-1-(2.00) Printed in Japan ddc/cdt