30mV LD03-10B12 3W 12V/250mA 330mA/60s W LD03-10B15 15V/200mA 250mA/60s W LD03-10B24. 24V/125mA 160mA/60s

Transcription

1 D0-05 SERIES -5W, AC-DC COVERTER Dseries ----is a compact size power converter offered by Mornsun for PCB mount installation applications. It features universal input voltage, taking both DC and AC input voltage, low power consumption, high efficiency, high reliability, safer isolation. It offers good EMC performance, meets IEC, U950and IEC950 standards, and is U & CE certified, and widely used in industrial,medical,electricity, instruments, telecommunication and civil applications. RoHS PRODUCT FEATURES. Universal Input: 85 ~ 4VAC, 50/Hz 2. AC and DC all in one (input from the same terminal). ow Ripple and oise 4. Over output voltage protection, short circuit protection and Over temperature 5. High efficiency, High power density 6. ow loss, green power 7. Multiple models available 8. industrial, medical level specifications 9. Three years warranty MODE SEECTIO D05-B24 Output Voltage Output Style Input Voltage Isolation Voltage Rated Power Package Style Product Series PRODUCT PROGRAM Approval Model Package Power Output (Vo/Io) U/CE950 U/CE Output (Iomax/T) Ripple and oise (Typ) Efficiency (%,Typ) Standby Power(Typ) D0-0B0 2.W.V/700mA 900mA/s W D0-0B05 5V/0mA 750mA/s 72 0.W D0-0B09 9V/0mA 450mA/s W 7.0X2.0X5.0mm 0mV D0-0B2 W 2V/250mA 0mA/s W D0-0B5 5V/0mA 250mA/s W D0-0B24 24V/25mA ma/s W D05-B0 4.2W.V/250mA 0mA/s 66 0.W D05-B05 5V/0mA 00mA/s 72 0.W D05-B09 9V/550mA 700mA/s 0mV W 50.8X25.4X5.6mm 5W D05-B2 2V/4mA 550mA/s W D05-B5 D05-B24 5V/mA 450mA/s W 5.5W 24V/20mA 00mA/s W. Ripple and oise were measured by the method of anear measure (The details see the anear measure); 2. Unless otherwise specified, all specifications above are measured at rated input voltage and rated output load, TA=25 C, humidity < 75%;. All specifications stated in this datasheet are subject to the above listed models only. For specifications of non-standard models, please contact our technical support team. 4.Product can not be operated continuously over current, or it will cause permanent damage to the device. ITPUT SPECIFICATIOS Input Voltage Range 85~4VAC, 0~70VDC Input Frequency Input Current Inrush Current eakage current External input fuse (Recommended) 47~4Hz 0VAC 65mA, typ 0mA,typ 0VAC 0A, typ 0A, typ one 0.5A/250V A/250V 20VAC 0mA, typ 70mA, typ 20VAC A, typ A, typ Slow blow Slow blow D0-05 A/- Page of 5

2 OUTPUT SPECIFICATIOS Voltage set accuracy ±2% (typ) output ) Input variation oad variation (0% to %) ±0.5% (typ) ±% (typ) Ripple& noise(p-p) MHz Bandwidth 0mV(typ) mv(max) Short circuit protection Over temperature protection Continuous, and auto resume 50 C (max) Over output voltage protection diode clamp COMMO SPECIFICATIOS Temperature ranges Operating Power derating Storage: Case temperature: (above 55 C): -25 C ~ 70 C 2% / C - C ~ 05 C 95 C max Hold-up time (Vin=20VAC) 50ms(typ) Humidity 95%(max) Temperature coefficient Switching frequency I/O-isolation voltage EMI/RFI conducted EMC compliance Safety standards Safety approvals Safety Class Case material Install MTBF Package 0.02%/ C khz(typ) 000VAC/Min 00VAC/Min E550, level A E550, level A Electrostatic discharge ESD IEC/E -4-2 level 4 8kV/5kV perf. Criteria B RF field susceptibility IEC/E -4- level 0V/m perf. Criteria A Electrical fast transients IEC/E -4-4 level 2kV perf. Criteria B /bursts on mainsline * IEC/E -4-4 level 4 4kV perf. Criteria B *Surge IEC/E -4-5 level kv/2kv perf. Criteria B IEC/E -4-5 level 4 2kV/4kV perf. Criteria B IEC950,E950,U950 IE,E E950,U950 E- CASS ΙΙ U94V-0 PCB C 7X2X5mm 50.8X25.4X5.2mm * External circuit is required to models at inrush and electrical fast transients experiment, refer to typical application. TEMPERATURE VS OAD IPUT VOTAGE VS OAD oad(%) Temperature( C) Input voltage (Vac) Input voltage (Vdc) D0-05 A/- Page 2 of 5

3 TYPICA EFFICIECY CURVE Efficiency (%) Efficiency D0-0B05 5VAC D0-0B05 25VAC D0-0B2 5VAC D0-0B2 20VAC D0-0B24 5VAC D0-0B24 20VAC Efficiency (%) D05-BXX Efficiency D05-B05 5VAC D05-B05 20VAC D05-B2 5VAC D05-B2 20VAC D05-B24 5VAC D05-B24 20VAC AEAR MEASURE FUSE Connect Oscillograph probe Copper sheet D05-BXX FUSE Connect Oscillograph Probe Copper sheet oad oad 25.4mm 25.4mm TYPICA APPICATIOS *FUSE *TC *FUSE *TC C6 C7 F C8 Vo Figure Vo TVS R TVS R D05-BXX *FUSE *TC Vo Figure 2 *FUSE *TC C7 F C6 C8 Vo R R CY Figure D0 EMC Application Figure 4 D05 EMC Application EXTERA CAPACITORS TYPICA VAUE(Unit: mf) Model TVS Model D0-0B /0V P4KE6.8A D05-B D0-0B /0V P4KE6.8A D05-B D0-0B /0V P4KE2A D05-B09 0. D0-0B /0V P4KEA D05-B2 0. D0-0B /0V P4KEA D05-B5 0. D0-0B /0V P4KE0A D05-B Output filtering capacitor and input filtering capacitors are electrolytic capacitors, It is recommended to use high frequency and low impedance electrolytic capacitors. For capacitance and current of capacitor please refer to manufacture s datasheet. Voltage derating of capacitor should be % or above. is ceramic capacitor, it is used to filter high frequency noise. TVS is a recommended component to protect post-circuits (if converter fails). 2. To protect the device from damage, external circuit is required to models at inrush and electrical fast transients experiment, is required to and, model: 47KD0; It is recommended to connect FUSE, the parameter for is 0.5A/250V slow blow, for isa/250v slow blow. External input TC is recommended to use 5D-4 or 0Ω/2W wire-round resistor. (see figure,2). If EMC performance is required, recommended to add EMC filter at the input end(see figure,4) C6: X capacitor, recommended parameter 0.µF/275V; C7,C8: Y capacitor, recommended parameter 20pF/0V; CY: Y capacitor, recommended parameter 02K/0V, recommended external, to meet EMC higher require. F: common model choke, recommended inductance is about 0mH-0mH. 4. : Terminals and are internal rectification and filtering terminals. To protect the models further, it is recommended to connect an electrolytic capacitor (it is recommended to be 4.7µF/0V). If operation voltage of the module is between ~4VAC, can be removed. D0-05 A/- Page of 5

4 OUTIE DIMESIOS & PI COECTIOS MECHAICA DIMESIOS RECOMMEDED FOOTPRIT(TOP VIEW) 7.00 [.457] 0.48 [.0] 5.08 [0.0]. [0.047] 0.6 [0.0] 5.24 [0.0] 5.08 [0.0] 2.00 [0.906] 7.78 [0.700] [0.906] 7.78 [0.700] [0.] 0.6 [0.0] 5.24 [0.0] 5.08 [0.0] 5.00 [0.59] 4.0 [0.6] 5.08 [0.0] 0.48 [.0] 7.00 [.457] TUBE OUTIE DIMESIOS 2.54 [0.].50 [.04] 0. [0.0] FOOTPRIT DETAIS Pin 4 6 Function C Vo V(cap) -V(cap) )C: o connection. 2)Terminals and are DC&AC input, Terminals and are internal rectification and filtering terminals First Angle Projection Unit:mm[inch] Pin section tolerances:±0.0mm[±0.004inch] General tolerances:±0.50mm[±0.0inch].50 [.04] 6.50 [0.650] 8.00 [0.5] Unit :mm[inch] General tolerances: ±0.50mm[±0.0inch] =50mm[.866inch] Devices per tube quantity: pcs =2mm[8.66inch] Devices per tube quantity: 5pcs Short tube inner packaging box dimensions: 255*70*mm Short tube outer packaging carton dimensions: 75*2*270mm ong tube inner packaging box dimensions: 5*0*mm ong tube outer packaging carton dimensions(with two inner packaging boxes): 0*25*2mm ong tube outer packaging carton dimensions(with three inner packaging boxes): 0*25*25mm D0-05 A/- Page 4 of 5

5 D05-BXX MECHAICA DIMESIOS RECOMMEDED FOOTPRIT(TOP VIEW) 25. [.000].2 [0.0] [.0] 50. [2.000] [0.0] 2.70 [0.500] 0.6 [0.0]. [0.047] [.0] [2.000 ] [0.0] [.000 ] [0.] 5.6[0.597] TUBE OUTIE DIMESIOS.00[0.09] [2.] FOOTPRIT DETAIS Pin 2 4 Function Vo First Angle Projection Unit:mm[inch] Pin section tolerances:±0.0mm[±0.004inch] General tolerances:±0.50mm[±0.0inch] 8.00 [0.709] Unit :mm[inch] General tolerances: ±0.50mm[±0.0inch] =50mm[.866inch] Devices per tube quantity: 9pcs =2mm[8.66inch] Devices per tube quantity: 7pcs Short tube inner packaging box dimensions: 255*70*mm Short tube outer packaging carton dimensions: 75*2*270mm ong tube inner packaging box dimensions: 5*0*mm ong tube outer packaging carton dimensions(with two inner packaging boxes): 0*25*2mm ong tube outer packaging carton dimensions(with three inner packaging boxes): 0*25*25mm 7.00 [0.669] [0.984] MORSU Science & Technology Co.,td. Address: o. 5, Kehui St., Kehui development center, Science Ave., Guangzhou Science City, uogang district, Guangzhou,P.R.China. Tel: Fax: D0-05 A/- Page 5 of 5