PS9308L, PS9308L2. Preliminary Data Sheet DESCRIPTION FEATURES APPLICATIONS. R08DS0048EJ0200 Rev Sep 27, 2013

Transcription

1 . A OUTPUT CURRENT, HIGH CMR, IGBT GATE DRIVE, 6-PIN SDIP PHOTOCOUPLER DESCRIPTION Preliminary Data Sheet R8DS8EJ Rev.. The PS938L and PS938L are optical coupled isolators containing a GaAlAs LED on the input side and a photo diode, a signal processing circuit and a power output transistor on the output side on one chip. The PS938L and PS938L are in 6-pin plastic SDIP (Shrink Dual In-line Package). The PS938L has 8 mm creepage distance. The mount area of 6-pin plastic SDIP is half size of 8-pin DIP. The PS938L and PS938L are designed specifically for high common mode transient immunity (CMR) and high switching speed. It is suitable for driving IGBTs and MOS FETs. The PS938L is lead bending type (Gull-wing) for surface mounting. The PS938L is lead bending type for long creepage distance (Gull-wing) for surface mount. <R> FEATURES Long creepage distance (8 mm MIN.: PS938L) Half size of 8-pin DIP Peak output current (. A MAX.,. A MIN.) High speed switching (t PLH, t PHL =. μs MAX.) UVLO (Under Voltage Lock Out) protection with hysteresis High common mode transient immunity (CM H, CM L = ± kv/μs MIN.) Embossed tape product : PS938L-E3, PS938L-E3 : pcs/reel Pb-Free product Safety standards UL approved: No. E7 CSA approved: No. CA 39 (CAA, CAN/CSA-C. 66, 69) SEMKO approved (EN 66, EN 69) DIN EN677-- (VDE88-) approved (Option) PIN CONNECTION (Top View) 6 3 SHIELD. Anode. NC 3. Cathode. VEE. VO 6. VCC APPLICATIONS IGBT, Power MOS FET Gate Driver Industrial inverter IH (Induction Heating) The mark <R> shows major revised points. The revised points can be easily searched by copying an "<R>" in the PDF file and specifying it in the "Find what:" field. R8DS8EJ Rev.. Page of

2 PACKAGE DIMENSIONS (UNIT: mm) Lead Bending Type (Gull-wing) For Surface Mount PS938L (.8).8±.3 9.7± ±. 3.±..±..±. 6.8±..7.±.. M.8±. Lead Bending Type (Gull-wing) For Long Creepage Distance (Surface Mount) (.8).8±.3 PS938L.± ±. 3.±..±..±. 6.8±..7.±.. M.7±. R8DS8EJ Rev.. Page of

3 PHOTOCOUPLER CONSTRUCTION Parameter PS938L PS938L Air Distance (MIN.) 7 mm 8 mm Outer Creepage Distance (MIN.) 7 mm 8 mm Isolation Distance (MIN.). mm. mm <R> MARKING EXAMPLE R 938 N3 Company Initial Type Number Assembly Lot No. pin Mark N 3 Week Assembled Year Assembled (Last Digit) Rank Code R8DS8EJ Rev.. Page 3 of

4 <R> ORDERING INFORMATION Part Number Order Number Solder Plating Specification Packing Style Safety Standard Approval Application Part Number * PS938L PS938L-AX Pb-Free pcs (Tape pcs cut) Standard PS938L PS938L-E3 PS938L-E3-AX (Ni/Pd/Au) Embossed Tape products pcs/reel (UL, CSA, PS938L PS938L-AX pcs (Tape pcs cut) SEMKO PS938L PS938L-E3 PS938L-E3-AX Embossed Tape approved) pcs/reel PS938L-V PS938L-V-AX pcs (Tape pcs cut) DIN EN PS938L PS938L-V-E3 PS938L-V-E3-AX Embossed Tape (VDE 88-) pcs/reel approved (Option) PS938L-V PS938L-V-AX pcs (Tape pcs cut) PS938L PS938L-V-E3 PS938L-V-E3-AX Embossed Tape pcs/reel Note: *. For the application of the Safety Standard, following part number should be used. R8DS8EJ Rev.. Page of

5 ABSOLUTE MAXIMUM RATINGS (T A = C, unless otherwise specified) Parameter Symbol Ratings Unit Diode Forward Current I F ma Peak Transient I F (TRAN). A Forward Current (Pulse Width < μs) Reverse Voltage V R V Detector High Level Peak I OH (PEAK). A Output Current * Low Level Peak I OL (PEAK). A Output Current * Supply Voltage (V CC V EE ) to 3 V Output Voltage V O to V CC V Power Dissipation * P C mw Isolation Voltage *3 BV Vr.m.s. Total Power Dissipation * P T 3 mw Operating Frequency * f khz Operating Ambient Temperature T A to + C Storage Temperature T stg to + C Notes: *. Maximum pulse width = μs, Maximum duty cycle =.% *. Reduced to.8 mw/ C at T A = 7 C or more. *3. AC voltage for minute at T A = C, RH = 6% between input and output. Pins -3 shorted together, -6 shorted together. *. Reduced to. mw/ C at T A = 7 C or more. *. I OH (PEAK). A (.3 μs), I OL (PEAK). A (.3 μs) RECOMMENDED OPERATING CONDITIONS Parameter Symbol MIN. TYP. MAX. Unit Supply Voltage (V CC V EE ) 3 V Forward Current (ON) I F (ON) 7 6 ma Forward Voltage (OFF) V F (OFF).8 V Operating Ambient Temperature T A C R8DS8EJ Rev.. Page of

6 ELECTRICAL CHARACTERISTICS (at RECOMMENDED OPERATING CONDITIONS, V EE = GND, unless otherwise specified) Parameter Symbol Conditions MIN. TYP. * MAX. Unit Diode Forward Voltage V F I F = ma, T A = C..6.8 V Reverse Current I R V R = 3 V, T A = C μa Input Capacitance C IN f = MHz, V F = V, T A = C 3 pf Detector High Level Output Current I OH V O = (V CC V) *.. A Coupled V O = (V CC V) *3. Low Level Output Current I OL V O = (V EE +. V) *.. A V O = (V EE + V) *3. High Level Output Voltage V OH I O = ma * V CC 3. V CC.3 V Low Level Output Voltage V OL I O = ma.. V High Level Supply Current I CCH I F = ma, V O = open.. ma Low Level Supply Current I CCL V F = to.8 V, V O = open.. ma UVLO Threshold V UVLO+ V o > V, I F = ma UVLO Hysteresis Threshold Input Current (L H) Threshold Input Voltage (H L) V UVLO UVLO HYS..3 I FLH I O = ma, V O > V.8. ma V FHL I O = ma, V O < V.8 V Notes: *. Typical values at T A = C. *. Maximum pulse width = μs, Maximum duty cycle =.%. *3. Maximum pulse width = μs, Maximum duty cycle =.%. *. V OH is measured with the DC load current in this testing. (Maximum pulse width = ms, Maximum duty cycle = %) V R8DS8EJ Rev.. Page 6 of

7 <R> SWITCHING CHARACTERISTICS (at RECOMMENDED OPERATING CONDITIONS, V EE = GND, unless otherwise specified) Parameter Symbol Conditions MIN. TYP. * MAX. Unit Propagation Delay Time (L H) t PLH R g = Ω, C g = nf,.8. μs Propagation Delay Time (H L) t PHL f = khz,.. μs Pulse Width Distortion (PWD) t PHL t PLH Duty Cycle = %,.. μs Propagation Delay Time t PHL t PLH I F = ma.. μs (Difference Between Any Two Products) Rise Time t r ns Fall Time t f ns Common Mode Transient Immunity at High Level Output CM H T A = C, I F = ma, V CC = 3 V, V CM =. kv, V O (MIN.) = 6 V kv/μs Common Mode Transient Immunity at Low Level Output Note: CM L *. Typical values at T A = C. T A = C, I F = ma, V CC = 3 V, V CM =. kv, V O (MAX.) = V kv/μs R8DS8EJ Rev.. Page 7 of

8 TEST CIRCUIT Fig. IOH Test Circuit Fig. IOL Test Circuit 6 6. μf V. μf IOL VCC = to 3 V 3 IF = 7 to 6 ma SHIELD IOH VCC = to 3 V 3 SHIELD. V Fig. 3 VOH Test Circuit Fig. VOL Test Circuit IF = 7 to 6 ma SHIELD. μf VOH VCC = to 3 V ma 3 SHIELD. μf VOL ma VCC = to 3 V Fig. UVLO Test Circuit Fig. 6 IFLH Test Circuit IF = ma μf VO > V VCC IF 3. μf VO > V VCC = to 3 V SHIELD SHIELD R8DS8EJ Rev.. Page 8 of

9 Fig. 7 tplh, tphl, tr, tf Test Circuit and Wave Forms 6 IF = ma khz % DUTY CYCLE 3 SHIELD. μf VO Ω nf VCC = to 3 V IF VOUT tplh tr tf tphl 9% % % Fig. 8 CMR Test Circuit and Wave Forms IF A 6 VCM B 3 SHIELD VCM =. kv. μf VO VCC = 3 V V VO (Switch A: IF = ma) VO (Switch B: IF = ma) Δt δ V δ t = VCM Δt VOH 6 V V VOL R8DS8EJ Rev.. Page 9 of

10 <R> TYPICAL CHARACTERISTICS (T A = C, unless otherwise specified) DETECTOR POWER DISSIPATION vs. AMBIENT TEMPERATURE TOTAL POWER DISSIPATION vs. AMBIENT TEMPERATURE 3 Detector Power Dissipation PC (mw) Total Power Dissipation PT (mw) Ambient Temperature TA ( C) Ambient Temperature TA ( C) Forward Current IF (ma). FORWARD CURRENT vs. FORWARD VOLTAGE TA = + C + C +8 C + C + C C C Threshold Input Current IFLH (ma) 3 THRESHOLD INPUT CURRENT vs. AMBIENT TEMPERATURE VCC = 3 V, VO > V, IO = ma Forward Voltage VF (V) 6 8 Ambient Temperature TA ( C) Output Voltage VO (V) 3 3 VCC = 3 V OUTPUT VOLTAGE vs. FORWARD CURRENT 3 Forward Current IF (ma) High Level Output Voltage Supply Voltage VOH VCC (V) HIGH LEVEL OUTPUT VOLTAGE SUPPLY VOLTAGE vs. AMBIENT TEMPERATURE. VCC = 3 V,. IF = ma, IO = ma Ambient Temperature TA ( C) Remark The graphs indicate nominal characteristics. R8DS8EJ Rev.. Page of

11 High Level Output Current IOH (A) 3 HIGH LEVEL OUTPUT CURRENT vs. AMBIENT TEMPERATURE VCC = 3 V, IF = ma VO = VCC V VO = VCC V Low Level Output Current IOL (A) 6 3 LOW LEVEL OUTPUT CURRENT vs. AMBIENT TEMPERATURE VO = VEE+ V VO = VEE+. V VCC = 3 V, IF = ma Ambient Temperature TA ( C) Ambient Temperature TA ( C) LOW LEVEL OUTPUT VOLTAGE vs. AMBIENT TEMPERATURE SUPPLY CURRENT vs. AMBIENT TEMPERATURE Low Level Output Voltage VOL (V) VCC = 3 V, IF = ma, IO = ma High Level Supply Current ICCH (ma) Low Level Supply Current ICCL (ma).... VCC = 3 V, VO = OPEN ICCH (IF = ma) ICCL (IF = ma) High Level Output Voltage Supply Voltage VOH VCC (V) VCC = 3 V, IF = ma Ambient Temperature TA ( C) HIGH LEVEL OUTPUT VOLTAGE SUPPLY VOLTAGE vs. HIGH LEVEL OUTPUT CURRENT TA = C TA = C TA = C High Level Output Current IOH (A) Low Level Output Voltage VOL (V) VCC = 3 V, IF = ma Ambient Temperature TA ( C) LOW LEVEL OUTPUT VOLTAGE vs. LOW LEVEL OUTPUT CURRENT TA = C TA = C TA = C Low Level Output Current IOL (A) Remark The graphs indicate nominal characteristics. R8DS8EJ Rev.. Page of

12 High Level Supply Current ICCH (ma) Low Level Supply Current ICCL (ma).... VO = OPEN SUPPLY CURRENT vs. SUPPLY VOLTAGE ICCH (IF = ma) ICCL (IF = ma). 3 Supply Voltage VCC (V) Propagation Delay Time tphl, tplh (ns), Pulse Width Distortion tphl tplh (ns) PROPAGATION DELAY TIME, PULSE WIDTH DISTORTION vs. AMBIENT TEMPERATURE VCC = 3 V, IF = ma, Rg = Ω, Cg = nf, f = khz, Duty cycle = % tphl tplh PWD 6 8 Ambient Temperature TA ( C) Propagation Delay Time tphl, tplh (ns), Pulse Width Distortion tphl tplh (ns) Propagation Delay Time tphl, tplh (ns), Pulse Width Distortion tphl tplh (ns) PROPAGATION DELAY TIME, PULSE WIDTH DISTORTION vs. FORWARD CURRENT VCC = 3 V, Rg = Ω, Cg = nf, f = khz, Duty Cycle = % tplh tphl PWD Forward Current IF (ma) PROPAGATION DELAY TIME, PULSE WIDTH DISTORTION vs. LOAD CAPACITANCE VCC = 3 V, IF = ma, Rg = Ω, f = khz, Duty Cycle = % tphl tplh PWD 3 Load Capacitance Cg (nf) Propagation Delay Time tphl, tplh (ns), Pulse Width Distortion tphl tplh (ns) Propagation Delay Time tphl, tplh (ns), Pulse Width Distortion tphl tplh (ns) PROPAGATION DELAY TIME, PULSE WIDTH DISTORTION vs. SUPPLY VOLTAGE 3 IF = ma, Rg = Ω, Cg = nf, f = khz, Duty Cycle = % tphl VCC = 3 V, IF = ma, Cg = nf, f = khz, Duty Cycle = % tplh PWD Supply Voltage VCC (V) PROPAGATION DELAY TIME, PULSE WIDTH DISTORTION vs. LOAD RESISTANCE tphl tplh PWD 3 Load Resistance Rg (Ω) Remark The graphs indicate nominal characteristics. R8DS8EJ Rev.. Page of

13 Output Voltage VO (V) OUTPUT VOLTAGE vs. SUPPLY VOLTAGE POWER CONSUMPTION PER CYCLE vs. LOAD RESISTANCE IF = ma, VEE = GND 6 8 UVLOHYS Qg = nc 6 3 Qg = nc VUVLO VUVLO+ (. V) (.3 V) Qg = nc 3 Supply Voltage VCC VEE (V) Load Resistance Rg (Ω) Power Consumption Per Cycle ESW ( J) μ 8 7 Remark The graphs indicate nominal characteristics. R8DS8EJ Rev.. Page 3 of

14 <R> TAPING SPECIFICATIONS (UNIT: mm) Outline and Dimensions (Tape).±..± ±.. MAX. 7.±. 6.±.3.± ±..8±..3.±. Tape Direction PS938L-E3 Outline and Dimensions (Reel).±..±. 3.±. R..±.8 33±. ±. 7.±..±. Packing: pcs/reel R8DS8EJ Rev.. Page of

15 Outline and Dimensions (Tape).±..± ±.. MAX ±..8±..±..±..±.3.±..3 Tape Direction PS938L-E3 Outline and Dimensions (Reel).±..±. 3.±. R..±.8 33±. ±..±. 9.±. Packing: pcs/reel R8DS8EJ Rev.. Page of

16 RECOMMENDED MOUNT PAD DIMENSIONS (UNIT: mm) D B C A Part Number Lead Bending A B C D PS938L lead bending type (Gull-wing) for surface mount PS938L lead bending type (Gull-wing) for long creepage distance (surface mount) R8DS8EJ Rev.. Page 6 of

17 NOTES ON HANDLING (UNIT: mm). Recommended soldering conditions () Infrared reflow soldering Peak reflow temperature 6 C or below (package surface temperature) Time of peak reflow temperature seconds or less Time of temperature higher than C 6 seconds or less Time to preheat temperature from to 8 C ± 3 s Number of reflows Three Flux Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of. Wt% is recommended.) Recommended Temperature Profile of Infrared Reflow Package Surface Temperature T ( C) C ±3 s (preheating) 8 C (heating) to s to 6 s 6 C MAX. C Time (s) () Wave soldering Temperature 6 C or below (molten solder temperature) Time seconds or less Preheating conditions C or below (package surface temperature) Number of times One (Allowed to be dipped in solder including plastic mold portion.) Flux Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of. Wt% is recommended.) (3) Soldering by Soldering Iron Peak Temperature (lead part temperature) 3 C or below Time (each pins) 3 seconds or less Flux Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of. Wt% is recommended.) (a) Soldering of leads should be made at the point. to. mm from the root of the lead () Cautions Fluxes Avoid removing the residual flux with freon-based and chlorine-based cleaning solvent. R8DS8EJ Rev.. Page 7 of

18 . Cautions regarding noise Be aware that when voltage is applied suddenly between the photocoupler s input and output at startup, the output transistor may enter the on state, even if the voltage is within the absolute maximum ratings. USAGE CAUTIONS. This product is weak for static electricity by designed with high-speed integrated circuit so protect against static electricity when handling.. Board designing () By-pass capacitor of more than. μf is used between V CC and GND near device. Also, ensure that the distance between the leads of the photocoupler and capacitor is no more than mm. () When designing the printed wiring board, ensure that the pattern of the IGBT collectors/emitters is not too close to the input block pattern of the photocoupler. If the pattern is too close to the input block and coupling occurs, a sudden fluctuation in the voltage on the IGBT output side might affect the photocoupler s LED input, leading to malfunction or degradation of characteristics. (If the pattern needs to be close to the input block, to prevent the LED from lighting during the off state due to the abovementioned coupling, design the input-side circuit so that the bias of the LED is reversed, within the range of the recommended operating conditions, and be sure to thoroughly evaluate operation.) (3) Pin (which is an NC * pin) can either be connected directly to the GND pin on the LED side or left open. Unconnected pins should not be used as a bypass for signals or for any other similar purpose because this may degrade the internal noise environment of the device. Note: *. NC: Non-Connection (No Connection). 3. Make sure the rise/fall time of the forward current is. μs or less.. In order to avoid malfunctions, make sure the rise/fall slope of the supply voltage is 3 V/μs or less.. Avoid storage at a high temperature and high humidity. R8DS8EJ Rev.. Page 8 of

19 <R> SPECIFICATION OF VDE MARKS LICENSE DOCUMENT Parameter Symbol Spec. Unit Climatic test class (IEC 668-/DIN EN 668-) // Dielectric strength maximum operating isolation voltage Test voltage (partial discharge test, procedure a for type test and random test) U pr =.6 U IORM., P d < pc Test voltage (partial discharge test, procedure b for all devices) U pr =.87 U IORM., P d < pc U IORM U pr 3 88 V peak V peak U pr 9 V peak Highest permissible overvoltage U TR 8 V peak Degree of pollution (DIN EN 666- VDE Part ) Comparative tracking index (IEC 6/DIN EN 6 (VDE 33 Part )) CTI 7 Material group (DIN EN 666- VDE Part ) III a Storage temperature range T stg to + C Operating temperature range T A to + C Isolation resistance, minimum value V IO = V dc at T A = C V IO = V dc at T A MAX. at least C Safety maximum ratings (maximum permissible in case of fault, see thermal derating curve) Package temperature Current (input current I F, Psi = ) Power (output or total power dissipation) Isolation resistance V IO = V dc at T A = Tsi Ris MIN. Ris MIN. Tsi Isi Psi Ris MIN. Ω Ω C ma mw Ω R8DS8EJ Rev.. Page 9 of

20 Caution GaAs Products This product uses gallium arsenide (GaAs). GaAs vapor and powder are hazardous to human health if inhaled or ingested, so please observe the following points. Follow related laws and ordinances when disposing of the product. If there are no applicable laws and/or ordinances, dispose of the product as recommended below.. Commission a disposal company able to (with a license to) collect, transport and dispose of materials that contain arsenic and other such industrial waste materials.. Exclude the product from general industrial waste and household garbage, and ensure that the product is controlled (as industrial waste subject to special control) up until final disposal. Do not burn, destroy, cut, crush, or chemically dissolve the product. Do not lick the product or in any way allow it to enter the mouth. R8DS8EJ Rev.. Page of

21 Revision History Data Sheet Description Rev. Date Page Summary. Aug 3, First edition issued. p. Modification of FEATURES p.3 Modification of MARKING EXAMPLE p. Modification of ORDERING INFORMATION p.7 Modification of SWITCHING CHARACTERISTICS pp. to 3 Addition of TYPICAL CHARACTERISTICS pp. to Modification of TAPING SPECIFICATIONS p.9 Modification of SPECIFICATION OF VDE MARKS LICENCE DOCUMENT All trademarks and registered trademarks are the property of their respective owners. C -

22 Notice. Descriptions of circuits, software and other related information in this document are provided only to illustrate the operation of semiconductor products and application examples. You are fully responsible for the incorporation of these circuits, software, and information in the design of your equipment. Renesas Electronics assumes no responsibility for any losses incurred by you or third parties arising from the use of these circuits, software, or information.. Renesas Electronics has used reasonable care in preparing the information included in this document, but Renesas Electronics does not warrant that such information is error free. Renesas Electronics assumes no liability whatsoever for any damages incurred by you resulting from errors in or omissions from the information included herein. 3. Renesas Electronics does not assume any liability for infringement of patents, copyrights, or other intellectual property rights of third parties by or arising from the use of Renesas Electronics products or technical information described in this document. No license, express, implied or otherwise, is granted hereby under any patents, copyrights or other intellectual property rights of Renesas Electronics or others.. You should not alter, modify, copy, or otherwise misappropriate any Renesas Electronics product, whether in whole or in part. Renesas Electronics assumes no responsibility for any losses incurred by you or third parties arising from such alteration, modification, copy or otherwise misappropriation of Renesas Electronics product.. Renesas Electronics products are classified according to the following two quality grades: "Standard" and "High Quality". The recommended applications for each Renesas Electronics product depends on the product's quality grade, as indicated below. "Standard": Computers; office equipment; communications equipment; test and measurement equipment; audio and visual equipment; home electronic appliances; machine tools; personal electronic equipment; and industrial robots etc. "High Quality": Transportation equipment (automobiles, trains, ships, etc.); traffic control systems; anti-disaster systems; anti-crime systems; and safety equipment etc. Renesas Electronics products are neither intended nor authorized for use in products or systems that may pose a direct threat to human life or bodily injury (artificial life support devices or systems, surgical implantations etc.), or may cause serious property damages (nuclear reactor control systems, military equipment etc.). You must check the quality grade of each Renesas Electronics product before using it in a particular application. You may not use any Renesas Electronics product for any application for which it is not intended. Renesas Electronics shall not be in any way liable for any damages or losses incurred by you or third parties arising from the use of any Renesas Electronics product for which the product is not intended by Renesas Electronics. 6. You should use the Renesas Electronics products described in this document within the range specified by Renesas Electronics, especially with respect to the maximum rating, operating supply voltage range, movement power voltage range, heat radiation characteristics, installation and other product characteristics. Renesas Electronics shall have no liability for malfunctions or damages arising out of the use of Renesas Electronics products beyond such specified ranges. 7. Although Renesas Electronics endeavors to improve the quality and reliability of its products, semiconductor products have specific characteristics such as the occurrence of failure at a certain rate and malfunctions under certain use conditions. Further, Renesas Electronics products are not subject to radiation resistance design. Please be sure to implement safety measures to guard them against the possibility of physical injury, and injury or damage caused by fire in the event of the failure of a Renesas Electronics product, such as safety design for hardware and software including but not limited to redundancy, fire control and malfunction prevention, appropriate treatment for aging degradation or any other appropriate measures. Because the evaluation of microcomputer software alone is very difficult, please evaluate the safety of the final products or systems manufactured by you. 8. Please contact a Renesas Electronics sales office for details as to environmental matters such as the environmental compatibility of each Renesas Electronics product. Please use Renesas Electronics products in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances, including without limitation, the EU RoHS Directive. Renesas Electronics assumes no liability for damages or losses occurring as a result of your noncompliance with applicable laws and regulations. 9. Renesas Electronics products and technology may not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any applicable domestic or foreign laws or regulations. You should not use Renesas Electronics products or technology described in this document for any purpose relating to military applications or use by the military, including but not limited to the development of weapons of mass destruction. When exporting the Renesas Electronics products or technology described in this document, you should comply with the applicable export control laws and regulations and follow the procedures required by such laws and regulations.. It is the responsibility of the buyer or distributor of Renesas Electronics products, who distributes, disposes of, or otherwise places the product with a third party, to notify such third party in advance of the contents and conditions set forth in this document, Renesas Electronics assumes no responsibility for any losses incurred by you or third parties as a result of unauthorized use of Renesas Electronics products.. This document may not be reproduced or duplicated in any form, in whole or in part, without prior written consent of Renesas Electronics.. Please contact a Renesas Electronics sales office if you have any questions regarding the information contained in this document or Renesas Electronics products, or if you have any other inquiries. (Note ) "Renesas Electronics" as used in this document means Renesas Electronics Corporation and also includes its majority-owned subsidiaries. (Note ) "Renesas Electronics product(s)" means any product developed or manufactured by or for Renesas Electronics. SALES OFFICES Refer to " for the latest and detailed information. California Eastern Laboratories, Inc. 9 Patrick Henry Drive, Santa Clara, California 9, U.S.A. Tel: , Fax: Renesas Electronics Europe Limited Dukes Meadow, Millboard Road, Bourne End, Buckinghamshire, SL8 FH, U.K Tel: , Fax: Renesas Electronics Europe GmbH Arcadiastrasse, 7 Düsseldorf, Germany Tel: , Fax: Renesas Electronics (China) Co., Ltd. 7th Floor, Quantum Plaza, No.7 ZhiChunLu Haidian District, Beijing 83, P.R.China Tel: , Fax: Renesas Electronics (Shanghai) Co., Ltd. Unit,, AZIA Center, No.33 Lujiazui Ring Rd., Pudong District, Shanghai, China Tel: , Fax: / Renesas Electronics Hong Kong Limited Unit 6-63, 6/F., Tower, Grand Century Place, 93 Prince Edward Road West, Mongkok, Kowloon, Hong Kong Tel: , Fax: /9 Renesas Electronics Taiwan Co., Ltd. 3F, No. 363, Fu Shing North Road, Taipei, Taiwan Tel: , Fax: Renesas Electronics Singapore Pte. Ltd. 8 Bendemeer Road, Unit #6- Hyflux Innovation Centre Singapore Tel: , Fax: Renesas Electronics Malaysia Sdn.Bhd. Unit 96, Block B, Menara Amcorp, Amcorp Trade Centre, No. 8, Jln Persiaran Barat, 6 Petaling Jaya, Selangor Darul Ehsan, Malaysia Tel: , Fax: Renesas Electronics Korea Co., Ltd. F., Samik Lavied' or Bldg., 7- Yeoksam-Dong, Kangnam-Ku, Seoul 3-8, Korea Tel: , Fax: Renesas Electronics Corporation. All rights reserved. [Colophon.]