Software updates Check the website for the latest software releases for your product.

Transcription

1

2

3 Trademark and patents notice Autohelm, hsb 2, RayTech Navigator, Sail Pilot, SeaTalk, SeaTalk NG, SeaTalk HS and Sportpilot are registered trademarks of Raymarine UK Limited. RayTalk, Seahawk, Smartpilot, Pathfinder and Raymarine are registered trademarks of Raymarine Holdings Limited. FLIR is a registered trademark of FLIR Systems, Inc. and/or its subsidiaries. All other trademarks, trade names, or company names referenced herein are used for identification only and are the property of their respective owners. This product is protected by patents, design patents, patents pending, or design patents pending. Fair Use Statement You may print no more than three copies of this manual for your own use. You may not make any further copies or distribute or use the manual in any other way including without limitation exploiting the manual commercially or giving or selling copies to third parties. Software updates Check the website for the latest software releases for your product. Product handbooks The latest versions of all English and translated handbooks are available to download in PDF format from the website Please check the website to ensure you have the latest handbooks. Copyright 2013 Raymarine UK Ltd. All rights reserved. ENGLISH Document number: Date:

4

5 Contents Chapter 1 Important information... 7 Safety notices... 7 General Information... 7 Chapter 2 Handbook information Handbook information Chapter 3 Planning the installation Installation checklist System integration Typical systems Chapter 4 Cables and connections General cabling guidance Connections overview Power connection Grounding Dedicated drain wire Power cable extension Breakers, fuses and circuit protection Sharing a breaker Network cable connector types Network connection multifunction display with RayNet connector Network connection multifunction display with RJ45 SeaTalk hs connector Network connection via network switch Network hardware Network cables Audio connection Antenna connection Chapter 5 Installation General location requirements Antenna installation SiriusXM receiver installation Activating your SiriusXM receiver Setup and operation Chapter 6 Maintenance and support Service and maintenance Cleaning Raymarine customer support Appendix A LED indications...51 Appendix B Spares and accessories...53 Appendix C Technical specification

6 6 SR150

7 Chapter 1: Important information Safety notices Warning: Product installation and operation This product must be installed and operated in accordance with the instructions provided. Failure to do so could result in personal injury, damage to your vessel and/or poor product performance. Warning: Maintain a permanent watch Always maintain a permanent watch, this will allow you to respond to situations as they develop. Failure to maintain a permanent watch puts yourself, your vessel and others at serious risk of harm. Warning: Potential ignition source This product is NOT approved for use in hazardous/flammable atmospheres. Do NOT install in a hazardous/flammable atmosphere (such as in an engine room or near fuel tanks). Warning: Switch off power supply Ensure the vessel s power supply is switched OFF before starting to install this product. Do NOT connect or disconnect equipment with the power switched on, unless instructed in this document. Warning: Product grounding Before applying power to this product, ensure it has been correctly grounded, in accordance with the instructions in this guide. Warning: Positive ground systems Do not connect this unit to a system which has positive grounding. Caution: Power supply protection When installing this product ensure the power source is adequately protected by means of a suitably-rated fuse or automatic circuit breaker. Caution: Service and maintenance This product contains no user serviceable components. Please refer all maintenance and repair to authorized Raymarine dealers. Unauthorized repair may affect your warranty. General Information EMC installation guidelines Raymarine equipment and accessories conform to the appropriate Electromagnetic Compatibility (EMC) regulations, to minimize electromagnetic interference between equipment and minimize the effect such interference could have on the performance of your system Important information 7

8 Correct installation is required to ensure that EMC performance is not compromised. For optimum EMC performance we recommend that wherever possible: Raymarine equipment and cables connected to it are: At least 1 m (3 ft) from any equipment transmitting or cables carrying radio signals e.g. VHF radios, cables and antennas. In the case of SSB radios, the distance should be increased to 7 ft (2 m). More than 2 m (7 ft) from the path of a radar beam. A radar beam can normally be assumed to spread 20 degrees above and below the radiating element. The product is supplied from a separate battery from that used for engine start. This is important to prevent erratic behavior and data loss which can occur if the engine start does not have a separate battery. Raymarine specified cables are used. Cables are not cut or extended, unless doing so is detailed in the installation manual. Note: Where constraints on the installation prevent any of the above recommendations, always ensure the maximum possible separation between different items of electrical equipment, to provide the best conditions for EMC performance throughout the installation Water ingress Water ingress disclaimer Although the waterproof rating capacity of this product meets the IPX6 & IPX7 standard, water intrusion and subsequent equipment failure may occur if the product is subjected to commercial high-pressure washing. Raymarine will not warrant products subjected to high-pressure washing. Suppression ferrites Raymarine cables may be fitted with suppression ferrites. These are important for correct EMC performance. If a ferrite has to be removed for any purpose (e.g. installation or maintenance), it must be replaced in the original position before the product is used. Use only ferrites of the correct type, supplied by Raymarine authorized dealers. Connections to other equipment Requirement for ferrites on non-raymarine cables If your Raymarine equipment is to be connected to other equipment using a cable not supplied by Raymarine, a suppression ferrite MUST always be attached to the cable near the Raymarine unit. Product disposal Dispose of this product in accordance with the WEEE Directive. The Waste Electrical and Electronic Equipment (WEEE) Directive requires the recycling of waste electrical and electronic equipment. Whilst the WEEE Directive does not apply to some Raymarine products, we support its policy and ask you to be aware of how to dispose of this product. Warranty registration To register your Raymarine product ownership, please visit and register online. It is important that you register your product to receive full warranty benefits. Your unit package includes a bar code label indicating the serial number of the unit. You will need this serial number when registering your product online. You should retain the label for future reference. 8 SR150

9 IMO and SOLAS The equipment described within this document is intended for use on leisure marine boats and workboats not covered by International Maritime Organization (IMO) and Safety of Life at Sea (SOLAS) Carriage Regulations. Technical accuracy To the best of our knowledge, the information in this document was correct at the time it was produced. However, Raymarine cannot accept liability for any inaccuracies or omissions it may contain. In addition, our policy of continuous product improvement may change specifications without notice. As a result, Raymarine cannot accept liability for any differences between the product and this document. Please check the Raymarine website ( to ensure you have the most up-to-date version(s) of the documentation for your product. Important information 9

10 10 SR150

11 Chapter 2: Handbook information Chapter contents 2.1 Handbook information on page 12 Handbook information 11

12 2.1 Handbook information This handbook describes installation of the SR150 SiriusXM receiver. The handbook includes information to help you: plan your installation and ensure you have all the necessary equipment, install and connect the SR150 as part of a wider system of connected marine electronics, troubleshoot problems and obtain technical support if required. This and other Raymarine product documentation is available to download in PDF format from Related products This document is applicable to the following product: Part number Name Description E70161 SR150 SiriusXM receiver. Product documentation Receiver for SiriusXM weather and satellite radio services. The following documentation is applicable to your product: Description SR150 Installation instructions Installation of an SR150 unit and connection to a wider system of marine electronics. SR150 Mounting template Mounting diagram for surface mounting an SR150 unit. Part number Description New a Series, c Series, e Series Installation and operation instructions Details the operation of the SiriusXM functions in the Weather and Sirius audio applications for New a Series, c Series, e Series multifunction displays. C-Series Widescreen User reference Details the operation of the SiriusXM functions in the Weather and Sirius audio applications for the Raymarine C90W, C120W, C140W multifunction displays. E-Series Widescreen User reference Details the operation of the SiriusXM functions in the Weather and Sirius audio applications for the Raymarine E90W, E120W, E140W multifunction displays. G-Series User reference Details the operation of the SiriusXM functions in the Weather and Sirius audio applications for the Raymarine G-Series GPM400 systems. E-Series Classic User reference Details the operation of the SiriusXM functions in the Weather and Sirius audio applications for the Raymarine E-Series Classic E80 and E120 multifunction displays. Part number SR150

13 Product overview The SR150 receiver enables you to receive SiriusXM marine weather and satellite radio services on your multifunction display. Select an audio channel from a list of hundreds of available satellite radio stations. Save presets (up to 5). Display all Advisory Messages, as determined by the Sirius specification. Control volume (including mute function). SiriusXM marine weather and satellite radio services are available on up to 6 compatible networked multifunction displays. Note: Networking features require that all multifunction displays are connected via a RayNet or an RJ45 SeaTalk hs connection. AUDIO ANTENNA NETWORK POWER The receiver has the following features when connected to a compatible Raymarine multifunction display: Receive and display SiriusXM marine weather data on your multifunction display, as provided by your SiriusXM service subscription. D Overlay historical, live and forecasted weather graphics on a world map in the Weather application on your multifunction display. Supports SiriusXM to Sirius Legacy translation. Receive and control SiriusXM satellite radio channels on your multifunction display, as provided by your SiriusXM service subscription: Handbook information 13

14 14 SR150

15 Chapter 3: Planning the installation Chapter contents 3.1 Installation checklist on page System integration on page Typical systems on page 22 Planning the installation 15

16 AUDIO ANTENNA NETWORK POWER 3.1 Installation checklist Parts supplied Installation includes the following activities: Installation Task 2 1 Plan your system. 2 Obtain all required equipment and tools Site all equipment. 4 Route all cables. 4 5 Drill cable and mounting holes. 6 Make all connections into equipment. 7 Secure all equipment in place Power on and test the system. Schematic diagram 7 8 A schematic diagram is an essential part of planning any installation. It is also useful for any future additions or maintenance of the system. The diagram should include: D Location of all components. 1. SR150 SiriusXM receiver. Connectors, cable types, routes and lengths. 2. RayNet to RayNet cable (female) 2 m (6.5 ft). 3. Power cable 2 m (6.5 ft). 4. Audio cable 2 m (6.5 ft). 5. SMA to SMB antenna adapter. 6. Mounting bracket. 7. Documentation pack. 8. Mounting screws x3. 16 SR150

17 For a list of associated part numbers, refer to 4.13 Network cables and Appendix B Spares and accessories. Required additional components To benefit from the full range of features available with the SiriusXM receiver, a number of additional data services and system components are required. Component / Service Sirius SRA-40 type-approved antenna Compatible Raymarine multifunction display GPS receiver provides position information for your vessel in the weather, chart and radar applications. Some multifunction displays have an internal GPS receiver. If your display does not have an internal GPS, an external GPS receiver will be required. Third-party external audio system required if you want to listen to SiriusXM satellite radio stations. Required for SiriusXM satellite radio Required for SiriusXM marine weather Component / Service SiriusXM marine weather subscription SiriusXM satellite radio subscription Required for SiriusXM satellite radio Compatible multifunction displays Required for SiriusXM marine weather The product is compatible with a range of Raymarine multifunction displays. Multifunction display product series New a Series, New c Series, New e Series gs Series C-Series Widescreen, E-Series Widescreen G-Series E-Series Classic Models a65, a67, a65 WiFi, a67 WiFi, e7, e7d, c95, c97, c125, c127, e95, e97, e125, e127, e165 gs95, gs125, gs165 C90W, C120W, C140W, E90W, E120W, E140W GPM400 E80, E120 Planning the installation 17

18 Software requirements To use your product you must ensure your Raymarine multifunction display is running the latest version of software. Multifunction display product series New a Series, New c Series, New e Series, gs Series Models a65, a67, a65 WiFi, a67 WiFi, e7, e7d, c95, c97, c125, c127, e95, e97, e125, e127, e165, gs95, gs125, gs165 Software version required v6.0 or later. C-Series Widescreen C90W, C120W, C140W v2.0 or later. E-Series Widescreen E90W, E120W, E140W v2.0 or later. G-Series GPM400 v4.0 or later. E-Series Classic E80, E120 v5.0 or later. the SiriusXM weather and satellite radio services on your receiver. Refer to 5.4 Activating your SiriusXM receiver for the activation procedure and Sirius contact details. SR150 compatibility with SR6 The SR150 is not suitable for use with the SR6 Sirius receiver. When installing an SR150 in a system that includes an SR6, the SR6 should be removed or disconnected from the system. Sirius Electronic Serial Number (ESN) Each Sirius receiver has its own unique identifying number ( Electronic Serial Number, or ESN ). You will need this number when contacting Sirius to activate your receiver. Ensure that you make a note of this Electronic Serial Number (ESN) before connecting any cables or mounting the unit. The ESN is located on the label on the underside of the receiver. This number will be required once installation is complete, in order to activate 18 SR150

19 AUDIO ANTENNA NETWORK POWER 3.2 System integration The SR150 is compatible with a wide range of marine electronics devices Planning the installation 19

20 Item Device type Maximum quantity Suitable devices Connections 1 SiriusXM receiver. 1 SR150 RayNet 2 Multifunction displays. 6 New a, c, e Series: a65 / a67 / e7 / e7d / c95 / c97 / c125 / c127 / e95 / e97 / e125 / e127 / e GPS receiver. As determined by the SeaTalk ng bus bandwidth and power loading. gs Series: gs95 / gs125 / gs165 C90W / C120W / C140W. E90W / E120W / E140W. G-Series GPM400 E-Series Classic: E80, E120 GPS position data is usually received from a multifunction display. If your multifunction display does NOT include an internal GPS receiver, an external GPS receiver will be required on the network. Multifunction display with internal GPS receiver. RS125 GPS (via optional SeaTalk to SeaTalk ng converter. RS130 GPS. 4 Sirius antenna 1 Sirius SRA-40 type-approved antenna RJ45 SeaTalk hs RayNet RJ45 SeaTalk hs SeaTalk ng 20 SR150

21 Item Device type Maximum quantity Suitable devices Connections 5 RayNet network switch, or RJ45 SeaTalk hs network switch. 6 HS5 network switch. RJ45 SeaTalk hs network switch. 6 Sonar module. 1 Multifunction display with internal sonar module. 7 Radar scanner. As determined by the SeaTalk hs system bandwidth. CP450C CHIRP sonar module. DSM30. DSM300. Non-HD Digital radome. HD Digital radome. HD Digital open array. SHD Digital open array. RayNet RJ45 SeaTalk hs RayNet RJ45 SeaTalk hs RayNet RJ45 SeaTalk hs Planning the installation 21

22 ANTENNA NETWORK POWER AUDIO ANTENNA NETWORK POWER 3.3 Typical systems Example: Expanded system Example: Basic system RayNet RayNet 4 7 Ethernet / RayNet SeaTalk hs / RayNet D RayNet network switch. 2. Multifunction display. 3. SiriusXM receiver. RayNet Digital radar scanner. D RayNet network switch. 2. Additional RayNet network switch. 22 SR150

23 3. Connection between 2 network switches. 4. Sonar module. 5. SiriusXM receiver. 6. Sirius antenna. 7. Multifunction display. 8. Digital radar scanner. 9. Thermal camera. Planning the installation 23

24 24 SR150

25 Chapter 4: Cables and connections Chapter contents 4.1 General cabling guidance on page Connections overview on page Power connection on page Grounding Dedicated drain wire on page Power cable extension on page Breakers, fuses and circuit protection on page Sharing a breaker on page Network cable connector types on page Network connection multifunction display with RayNet connector on page Network connection multifunction display with RJ45 SeaTalk hs connector on page Network connection via network switch on page Network hardware on page Network cables on page Audio connection on page Antenna connection on page 37 Cables and connections 25

26 4.1 General cabling guidance Cable types and length It is important to use cables of the appropriate type and length Unless otherwise stated use only standard cables of the correct type, supplied by Raymarine. Ensure that any non-raymarine cables are of the correct quality and gauge. For example, longer power cable runs may require larger wire gauges to minimize voltage drop along the run. Routing cables Cables must be routed correctly, to maximize performance and prolong cable life. Do NOT bend cables excessively. Wherever possible, ensure a minimum bend diameter of 200 mm (8 in) / minimum bend radius of 100 mm (4 in). Protect all cables from physical damage and exposure to heat. Use trunking or conduit where possible. Do NOT run cables through bilges or doorways, or close to moving or hot objects. Secure cables in place using tie-wraps or lacing twine. Coil any extra cable and tie it out of the way. Where a cable passes through an exposed bulkhead or deckhead, use a suitable watertight feed-through. Do NOT run cables near to engines or fluorescent lights. Always route data cables as far away as possible from: other equipment and cables, high current carrying ac and dc power lines, antennae. Strain relief Ensure adequate strain relief is provided. Protect connectors from strain and ensure they will not pull out under extreme sea conditions. Circuit isolation Appropriate circuit isolation is required for installations using both AC and DC current: Always use isolating transformers or a separate power-inverter to run PC s, processors, displays and other sensitive electronic instruments or devices. Always use an isolating transformer with Weather FAX audio cables. Always use an isolated power supply when using a 3rd party audio amplifier. Always use an RS232/NMEA converter with optical isolation on the signal lines. Always make sure that PC s or other sensitive electronic devices have a dedicated power circuit. Cable shielding Ensure that all data cables are properly shielded that the cable shielding is intact (e.g. hasn t been scraped off by being squeezed through a tight area). 26 SR150

27 4.2 Connections overview 4.3 Power connection The SiriusXM receiver must be connected to a 12 / 24 V power supply, as appropriate. 1 SXM D Antenna, for connection to Sirius SRA-40 type-approved antenna, via the supplied SMA to SMB adapter. 2. Audio, for connection to external audio system Network, for connection to a network switch or multifunction display. 4. Power, for connection to 12 V / 24 V power supply (as appropriate). Note: If the audio connection is not required, the attached protective cap should be placed securely on the connector to protect it. This protective cap is not shown in the illustration above. 1. SiriusXM receiver connections panel. 2. Power cable. 3. Connection to 12 V / 24 V power supply (as appropriate). 4. Red cable (positive). 5. Shield (drain) wire (thin black wire; must be connected to RF ground point). 6. Black cable (negative). D Power distribution Raymarine recommends that all power connections are made via a distribution panel. Cables and connections 27

28 All equipment must be powered from a breaker or switch, with appropriate circuit protection. All equipment should be wired to individual breakers if possible. Warning: Product grounding Before applying power to this product, ensure it has been correctly grounded, in accordance with the instructions in this guide. 4.4 Grounding Dedicated drain wire The power cable supplied with this product includes a dedicated shield (drain) wire for connection to a vessel's RF ground point. It is important that an effective RF ground is connected to the system. A single ground point should be used for all equipment. The unit can be grounded by connecting the shield (drain) wire of the power cable to the vessel's RF ground point. On vessels without an RF ground system the shield (drain) wire should be connected directly to the negative battery terminal. The dc power system should be either: Negative grounded, with the negative battery terminal connected to the vessel's ground. Floating, with neither battery terminal connected to the vessel's ground Warning: Positive ground systems Do not connect this unit to a system which has positive grounding. 28 SR150

29 4.5 Power cable extension The product is supplied with a power cable, which can be extended if required. The following restrictions apply to any extension to the power cable: Cable must be of a suitable gauge for the circuit load. Each unit should have its own dedicated power cable wired back to the distribution panel. Total length (max) Supply voltage Cable gauge (AWG) 0 5 m ( ft) 5 10 m ( ft) m ( ft) m ( ft) 12 V V V V V V V V Breakers, fuses and circuit protection It is recommended that you fit a thermal breaker or fuse at the distribution panel. Thermal breaker rating 5 A (if only connecting one device) Note: The suitable fuse rating for the thermal breaker is dependent on the number of devices you are connecting. If in doubt consult an authorized Raymarine dealer. Note: These distances are for a 2 wire power cable run from the battery to the product (approximate distance). To calculate the round trip length, double the figure stated here. Cables and connections 29

30 4.7 Sharing a breaker Where more than 1 piece of equipment shares a breaker you must provide protection for the individual circuits. E.g. by connecting an in-line fuse for each power circuit. 4.8 Network cable connector types There are 2 types of network cable connector RayNet, and RJ45 SeaTalk hs. RJ45 SeaTalk hs connector. RayNet connector. 1 Positive (+) bar 2 Negative (-) bar 3 Circuit breaker 4 Fuse Where possible, connect individual items of equipment to individual circuit breakers. Where this is not possible, use individual in-line fuses to provide the necessary protection. 30 SR150

31 4.9 Network connection multifunction display with RayNet connector The SiriusXM receiver can be connected directly to a multifunction display using the supplied RayNet cable. The following multifunction displays feature a RayNet connector: 1 New a Series New c Series New e Series gs Series a65 c95 e7 gs95 a67 a65 WiFi c97 c125 e7d e95 gs125 gs165 2 a67 WiFi c127 e97 e125 e127 e165 3 D Multifunction display with RayNet connector. 2. RayNet to RayNet cable (supplied with SiriusXM receiver). 3. SiriusXM receiver. Note: For a list of associated part numbers, refer to 4.13 Network cables. Cables and connections 31

32 4.10 Network connection multifunction display with RJ45 SeaTalk hs connector The SiriusXM receiver can be connected directly to a multifunction display with an RJ45 SeaTalk hs connector, using optional RayNet to RJ45 SeaTalk hs adapter cables. The following multifunction displays feature an RJ45 SeaTalk hs connection: C-Series Widescreen C90W C120W C140W E-Series Widescreen G-Series E-Series Classic E90W E120W E140W GPM400 E80 E Note: For a list of associated cable part numbers, refer to 4.13 Network cables Multifunction display with RJ45 SeaTalk hs connection. 2. RJ45 SeaTalk hs cable (available separately). 3. RJ45 SeaTalk hs crossover coupler (available separately). 4. RayNet to RJ45 SeaTalk hs adapter cable (available separately). 32 SR150 D

33 4.11 Network connection via network switch For larger systems, the SiriusXM receiver can be connected to a multifunction display via a network switch. RayNet network switch connection Note: For a list of associated part numbers, refer to 4.13 Network cables. RJ45 SeaTalk hs network switch connection SXM D RayNet network switch. 2. RayNet to RayNet cable (supplied). 3. SiriusXM receiver. D RJ45 SeaTalk hs network switch. 2. RJ45 SeaTalk hs cable (available separately). 3. RJ45 SeaTalk hs crossover coupler (available separately). 4. SiriusXM receiver. 5. RayNet to RJ45 SeaTalk hs adapter cable (available separately). Cables and connections 33

34 4.12 Network hardware Item Part number Notes HS5 RayNet network switch RJ45 SeaTalk hs network switch A80007 E port switch for network connection of multiple devices featuring RayNet connectors. Equipment with RJ45 SeaTalk hs connectors can also be connected via suitable adapter cables. 8 port switch for network connection of multiple SeaTalk hs devices featuring RJ45 connectors. Item Part number Notes RJ45 SeaTalk hs crossover coupler E55060 Enables direct connection of RJ45 SeaTalk hs devices to smaller systems where a switch is not required. Also enables the connection of RJ45 SeaTalk hs devices to an HS5 RayNet network switch (in conjunction with suitable adapter cables). Ethernet RJ45 coupler R32142 Enables direct connection of compatible thermal cameras to smaller systems where a network switch is not required. Also enables connection to larger systems via an RJ45 SeaTalk hs network switch or HS5 RayNet network switch (in conjunction with suitable adapter cables). 34 SR150

35 4.13 Network cables Cable Part number RayNet to RayNet cables Cable 400 mm (1.3 ft) RayNet to RayNet cable (female) Part number A m (32.8 ft) RayNet to RJ45 SeaTalk hs cable 400 mm (1.3 ft) RayNet to RJ45 SeaTalk hs (female) cable A80159 A m (6.56 ft) RayNet to RayNet cable (female) A m (16.4 ft) RayNet to RayNet cable (female) A m (32.8 ft) RayNet to RayNet cable (female) A m (65.6 ft) RayNet to RayNet cable (female) A mm (1.97 in) RayNet to RayNet cable (male) A80162 RayNet right angled coupler A80262 RayNet cable puller 5 pack R70014 RayNet to RJ45 SeaTalk hs adapter cables Cable 1 m (3.28 ft) RayNet to RJ45 SeaTalk hs cable 3 m (9.84 ft) RayNet to RJ45 SeaTalk hs cable Part number A62360 A80151 Cables and connections 35

36 4.14 Audio connection Use of the SiriusXM satellite radio service requires a connection to an external audio system, which must support an analog auxiliary audio input. A cable is supplied with the SiriusXM receiver which provides a female audio 3.5 mm socket connection. You will also need an additional cable that is suitable for connecting this supplied cable to a third-party external audio system. The type of cable required is dependent on the audio input connections available on the external audio system. If you do not have a suitable cable, a third-party adapter cable will be required. This is available separately from your local dealer or an electronics retailer. 2. Third-party external audio system. 3. Adapter cable with a male 3.5 mm plug and also a plug suitable for connection to the external audio system. 4. Audio cable, as supplied with SiriusXM receiver. Note: If the audio connection is not required, the attached protective cap should be placed securely on the connector to protect it. This protective cap is not shown in the illustration above D SiriusXM receiver. 36 SR150

37 4.15 Antenna connection The SiriusXM receiver requires the connection of an external third-party antenna, via the supplied SMA to SMB antenna adapter D Sirius-compatible SRA-40 type-approved antenna (available separately). 2. SMA to SMB Antenna adapter (supplied). 3. SiriusXM receiver. 4. Antenna cable 7.5 m (25 ft) (available separately). Note: For more information on cable and antenna requirements and associated part numbers, refer to 5.2 Antenna installation and Appendix B Spares and accessories. Cables and connections 37

38 38 SR150

39 Chapter 5: Installation Chapter contents 5.1 General location requirements on page Antenna installation on page SiriusXM receiver installation on page Activating your SiriusXM receiver on page Setup and operation on page 45 Installation 39

40 5.1 General location requirements When selecting a location for your product it is important to consider a number of factors. Key factors which can affect product performance are: Ventilation To ensure adequate airflow: Ensure that product is mounted in a compartment of suitable size. Ensure that ventilation holes are not obstructed. Allow adequate separation of all equipment. Any specific requirements for each system component are provided later in this chapter. Mounting surface Ensure product is adequately supported on a secure surface. Do not mount units or cut holes in places which may damage the structure of the vessel. Cable entry Ensure the product is mounted in a location which allows proper routing and connection of cables: Minimum bend radius of 100 mm (3.94 in) unless otherwise stated. Use cable supports to prevent stress on connectors. Water ingress The product is suitable for mounting both above and below decks. Although the unit is waterproof, it is good practice to locate it in a protected area away from prolonged and direct exposure to rain and salt spray. Electrical interference Select a location that is far enough away from devices that may cause interference, such as motors, generators and radio transmitters / receivers. Power supply Select a location that is as close as possible to the vessel s DC power source. This will help to keep cable runs to a minimum. 40 SR150

41 5.2 Antenna installation A separate antenna is required for the SiriusXM receiver. The antenna must be a Sirius-compatible SRA-40 type-approved antenna. A suitable antenna is available as an accessory from Raymarine. A suitable cable is required for connecting the antenna to the SiriusXM receiver. A 7.5 m (25 ft) antenna cable is available as an accessory from Raymarine. For installations where the distance between the antenna and the receiver is more than 7.5 m (25 ft), a range of third-party cable kits is available from your local dealer or other third-party distributor or retailer. Do NOT cut antenna cables or remove connectors. Note: For a list of associated part numbers, refer to Appendix B Spares and accessories. Location requirements antenna Important considerations when planning the installation location for the antenna. The antenna is waterproof and suitable for mounting above decks. Choose a location that provides the most unobstructed view of the sky in all directions: Ensure the antenna is installed on a flat horizontal surface. The antenna should be mounted at least 1 m (3 ft) away from devices that may cause interference, such as engines, generators, VHF radio units, or other transmitters / receivers. The antenna should be mounted away from any metal objects or other structures that could block line-of-sight reception of the satellite signal. Ensure the antenna is NOT mounted in the path of the beam emitted from any radar scanner units. If the Mounting the antenna pedestal mounting The antenna is supplied with fixing components. Installation 41

42 5. Insert the antenna cable through the mounting surface hole, mounting gasket, and mounting flange. 6. Insert the sealing ring into position on the mounting flange. 7. Connect the cable to the antenna. 8. Secure the antenna to the mounting flange. When screwing the antenna clockwise to secure it in place, rotate the cable counter-clockwise at the same time to prevent twisting the cable. Ensure the cable turns freely and does not bind. Note: Once the installation is complete and the cable is in position and connected to the antenna, Raymarine recommends that a suitable silicone sealant is used to seal the center hole, to prevent water ingress. Mounting the antenna - surface mounting The antenna is supplied with fixing components. 1. Use the supplied gasket as a guide to mark 3 positions in the mounting surface for the drill holes. 2. Using a drill bit suitable for the mounting surface material and the size of the supplied screws, drill the pilot holes for the fixing screws. 3. Drill the center hole, suitable for routing the cable through the mounting surface and the mounting gasket. 4. Using the supplied screws, secure the mounting gasket and mounting flange to the mounting surface. 1. Use the screw thread on the antenna as a guide to mark the mounting hole on the mounting surface. 42 SR150

43 AUDIO ANTENNA NETWORK 2. Using a drill bit suitable for the mounting surface material, drill the mounting hole. 3. Insert the antenna into position. Note: If the mounting surface thickness is 6 mm (0.25 in) to 25 mm (1 in), insert the supplied extension shaft in the mounting hole to support the antenna and cable. 4. Insert the lock washer over the antenna screw thread. 5. Using the supplied retaining nut, secure the antenna to the mounting surface. 6. Connect the cable to the antenna. Note: Once the installation is complete and the cable is in position and connected to the antenna, Raymarine recommends that a suitable silicone sealant is used to seal the mounting hole, to prevent water ingress. 5.3 SiriusXM receiver installation Warning: Potential ignition source This product is NOT approved for use in hazardous/flammable atmospheres. Do NOT install in a hazardous/flammable atmosphere (such as in an engine room or near fuel tanks). Product dimensions A B C POW ER D D A B C (including connectors) D (including mounting bracket) mm (5.28 in) mm (4.84 in) mm (5.11 in) 59.7 mm (2.35 in) Installation 43

44 Mounting the receiver 1. Using the supplied mounting template, drill 3 holes appropriate for the mounting bracket. 2. Secure the bracket to the mounting surface using the supplied screws. D Connect the cables to the unit as described in this document. D Align the grooves on the rear of the receiver with the mounting bracket and gently slide the receiver down into position until it clicks into place. 44 SR150

45 5.4 Activating your SiriusXM receiver Once the installation is complete and the receiver is connected to the multifunction display and powered up, you must activate your receiver in order to start receiving SiriusXM weather and satellite radio services. Before completing the activation procedure, ensure that the receiver and multifunction display are powered up, and that you have the following information to hand: Electronic Serial Number (ESN), printed on the label on the underside of the SiriusXM receiver. Also available by selecting Menu > Sirius ESN in the Weather application on a New a, c or e Series multifunction display. Billing information (only required if you do not already subscribe to a SiriusXM weather or audio data package). Your choice of subscription package (only required if you do not already subscribe to a SiriusXM weather or audio data package). 1. Call Sirius on If you already subscribe to a SiriusXM weather or audio data package, ask the Sirius Customer Care representative to add your receiver s ESN to your existing Sirius account. 5.5 Setup and operation For setup and operation instructions for your Sirius receiver, refer to the handbook that accompanies your multifunction display. Note: Activation of your SiriusXM receiver is undertaken with a third party (Sirius). Raymarine has no involvement in or responsibility for this activation process. Installation 45

46 46 SR150

47 Chapter 6: Maintenance and support Chapter contents 6.1 Service and maintenance on page Cleaning on page Raymarine customer support on page 49 Maintenance and support 47

48 6.1 Service and maintenance This product contains no user serviceable components. Please refer all maintenance and repair to authorized Raymarine dealers. Unauthorized repair may affect your warranty. 6.2 Cleaning 1. Switch off the power to the unit. 2. Wipe the unit with a clean, damp cloth. 3. If necessary, use isopropyl alcohol (IPA) or a mild detergent to remove grease marks. Note: Do NOT use abrasive, or acid or ammonia based products. 48 SR150

49 6.3 Raymarine customer support Raymarine provides a comprehensive customer support service. You can contact customer support through the Raymarine website, telephone and . If you are unable to resolve a problem, please use any of these facilities to obtain additional help. Web support Please visit the customer support area of our website at: This contains Frequently Asked Questions, servicing information, access to the Raymarine Technical Support Department and details of worldwide Raymarine agents. Product identity. Serial number. Software application version. System diagrams. You can obtain this product information using the menus within your product. Telephone and support In the USA: Tel: Toll Free: support@raymarine.com In the UK, Europe, and the Middle East: Tel: +44 (0) ukproduct.support@raymarine.com In Southeast Asia and Australia: Tel: +61 (0) aus.support@raymarine.com Product information If you need to request service, please have the following information to hand: Product name. Maintenance and support 49

50 50 SR150

51 Appendix A LED indications LED name LED color Status Action required Audio Off Audio channel is silent (e.g. channel 0 or muted). Solid green Normal operation. None. Un-mute the channel in the Sirius audio application on your multifunction display if you want to hear audio. Antenna Fast flash green SiriusXM receiver failure. If problem persists contact Raymarine technical support. Off Antenna not connected. Connect the antenna to the receiver as described in this document and the installation instructions supplied with the antenna. If problem persists contact Raymarine technical support. Flash green No signal. Ensure there is no source of antenna interference. Solid green Antenna connected. None. Restart the SiriusXM receiver by disconnecting the power cable and then reconnecting. If problem persists contact Raymarine technical support. Fast flash green x2 Antenna short circuit. Check antenna connections at the receiver and the antenna, including any extension cables. If problem persists contact Raymarine technical support. LED indications 51

52 LED name LED color Status Action required Network Off No network connection. Check network connections at the receiver and the multifunction display or network switch (as appropriate), including any adapter cables. Solid green Data link active. None. Flash green Data activity. None. If problem persists contact Raymarine technical support. Power Off No power to receiver. Check power connection to receiver. Solid amber Receiver is switched on. None. If problem persists contact Raymarine technical support. 52 SR150

53 Appendix B Spares and accessories Spares Item Part number Notes Handbook / Mounting Bracket / Screw Kit Accessories A80237 Item Part number Notes Sirius SRA-40 type-approved antenna Antenna cable 7.5 m (25 ft) E03010 E03011 Appendix C Technical specification Dimensions Weight Nominal supply voltage Operating voltage range Power consumption (typical) Environmental Width: mm (5.28 in) Height (including connectors): mm (5.11 in) Depth (including mounting bracket): 59.7 mm (2.35 in) 0.40 kg (0.88 lbs) 12 or 24 V dc 10.8 V to 31.2 V dc < 3.0 W Installation environment Operating temperature: -15 ºC to +55 ºC (+5 ºF to +131 ºF) Storage temperature: -35 ºC to +85 ºC (-31 ºF to +185 ºF) Waterproof to IPX 7 Spares and accessories 53

54 54 SR150

55

56