TEST REPORT SZEM CR

Transcription

1 No. 1 Workshop, M-10, Middle section, Science & Technology Park, Shenzhen, Guangdong, China Telephone: +86 (0) Fax: +86 (0) ee.shenzhen@sgs.com Application No.: Applicant: Address of Applicant: Manufacturer: Address of Manufacturer: Factory: Address of Factory: Equipment Under Test (EUT): EUT Name: Model No.: Trade mark: FCC ID: TEST REPORT SZEM CR Page: 1 of 31 Electrocelos - Sistemas Automatizados e Comunicacoes de Barcelos, S.A. Travessa do Sobreiro, no Rio Covo (Sta Eugenia) Barcelos, Portugal Electrocelos - Sistemas Automatizados e Comunicacoes de Barcelos, S.A. Travessa do Sobreiro, no Rio Covo (Sta Eugenia) Barcelos, Portugal Shanghai Baolu Technology Co., Ltd. 8/F,Xianglu Industry Park, No.3009 Gudai Road, Shanghai, China Transmitter FAIK MOTORLINE Professional 2ANXP-FALKMOTORLINE Standards: 47 CFR Part 15, Subpart C Date of Receipt: Date of Test: to Date of Issue: Test Result : Pass* * In the configuration tested, the EUT complied with the standards specified above. Jack Zhang EMC Laboratory Manager The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of SGS International Electrical Approvals or testing done by SGS International Electrical Approvals in connection with, distribution or use of the product described in this report must be approved by SGS International Electrical Approvals in writing.

2 Page: 2 of 31 Revision Record Version Chapter Date Modifier Remark Original Authorized for issue by: Leo Li /Project Engineer Eric Fu /Reviewer

3 Page: 3 of 31 2 Test Summary Radio Spectrum Technical Requirement Item Standard Method Requirement Result Antenna Requirement 47 CFR Part 15, Subpart C N/A 47 CFR Part 15, Subpart C Pass Radio Spectrum Matter Part Item Standard Method Requirement Result 20dB Bandwidth Dwell Time (15.231(a)) Field Strength of the Fundamental Signal (15.231(b)) Radiated Emissions 47 CFR Part 15, Subpart C CFR Part 15, Subpart C CFR Part 15, Subpart C CFR Part 15, Subpart C ANSI C63.10 (2013) Section 6.9 ANSI C63.10 (2013) Section ANSI C63.10 (2013) Section 6.5 ANSI C63.10 (2013) Section 6.4&6.5& CFR Part 15, Subpart C (c) 47 CFR Part 15, Subpart C (a) 47 CFR Part 15, Subpart C (b) 47 CFR Part 15, Subpart C (b) Pass Pass Pass Pass

4 3 Contents Page: 4 of 31 1 COVER PAGE TEST SUMMARY CONTENTS GENERAL INFORMATION DETAILS OF E.U.T DESCRIPTION OF SUPPORT UNITS MEASUREMENT UNCERTAINTY TEST LOCATION TEST FACILITY DEVIATION FROM STANDARDS ABNORMALITIES FROM STANDARD CONDITIONS EQUIPMENT LIST RADIO SPECTRUM TECHNICAL REQUIREMENT ANTENNA REQUIREMENT Test Requirement: Conclusion RADIO SPECTRUM MATTER TEST RESULTS DB BANDWIDTH E.U.T. Operation Test Setup Diagram Measurement Procedure and Data DWELL TIME E.U.T. Operation Test Setup Diagram Measurement Procedure and Data DUTY CYCLE Spurious Emissions RADIATED EMISSIONS E.U.T. Operation Test Setup Diagram Measurement Procedure and Data PHOTOGRAPHS FIELD STRENGTH OF THE FUNDAMENTAL SIGNAL (15.231(B)) TEST SETUP RADIATED EMISSIONS TEST SETUP EUT CONSTRUCTIONAL DETAILS Page

5 Page: 5 of 31 4 General Information 4.1 Details of E.U.T. Sample Type: Portable production Transmission type Manually operated Operation Frequency: MHz Channel Numbers: 1 Modulation Type: OOK Antenna Type: Loop Antenna Antenna Gain: 0dBi Power supply: DC 3.0V(1x3.0 "CR2" LITHIUM BATTERY) Test voltage DC 3V 4.2 Description of Support Units The EUT has been tested as an independent unit. 4.3 Measurement Uncertainty No. Item Measurement Uncertainty 1 Radio Frequency 7.25 x Duty cycle 0.37% 3 Occupied Bandwidth 3% 4 RF conducted power 0.75dB 5 RF power density 2.84dB 6 Conducted Spurious emissions 0.75dB 7 RF Radiated power 4.5dB (below 1GHz) 4.8dB (above 1GHz) 8 Radiated Spurious emission test 4.5dB (30MHz-1GHz) 4.8dB (1GHz-18GHz) 9 Temperature test 1 C 10 Humidity test 3% 11 Supply voltages 1.5% 12 Time 3%

6 4.4 Test Location All tests were performed at:, Page: 6 of 31 No. 1 Workshop, M-10, Middle Section, Science & Technology Park, Shenzhen, Guangdong, China Tel: Fax: No tests were sub-contracted. 4.5 Test Facility The test facility is recognized, certified, or accredited by the following organizations: CNAS (No. CNAS L2929) CNAS has accredited EMC Lab to ISO/IEC 17025:2005 General Requirements for the Competence of Testing and Calibration Laboratories (CNAS-CL01 Accreditation Criteria for the Competence of Testing and Calibration Laboratories) for the competence in the field of testing. A2LA (Certificate No ), Shenzhen EMC Laboratory is accredited by the American Association for Laboratory Accreditation(A2LA). Certificate No VCCI The 10m Semi-anechoic chamber and Shielded Room of SGS-CSTC Standards Technical Services Co., Ltd. have been registered in accordance with the Regulations for Voluntary Control Measures with Registration No.: G-823, R-4188, T-1153 and C-2383 respectively. FCC Designation Number: CN1178, Shenzhen EMC Laboratory has been recognized as an accredited testing laboratory. Designation Number: CN1178. Test Firm Registration Number: Industry Canada (IC) Two 3m Semi-anechoic chambers and the 10m Semi-anechoic chamber of SGS-CSTC Standards Technical Services Co., Ltd. EMC Lab have been registered by Certification and Engineering Bureau of Industry Canada for radio equipment testing with Registration No.: 4620C-1, 4620C-2, 4620C Deviation from Standards None 4.7 Abnormalities from Standard Conditions None

7 Page: 7 of 31 5 Equipment List 20dB Bandwidth Equipment Manufacturer Model No Inventory No Cal Date Cal Due Date DC Power Supply ZhaoXin RXN-305D SEM Spectrum Analyzer Rohde & Schwarz FSP SEM Measurement Software JS Tonscend JS BT/WIFI V2. N/A N/A N/A Signal Generator Rohde & Schwarz SML03 SEM Power Meter Rohde & Schwarz NRVS SEM Coaxial Cable SGS N/A SEM Dwell Time Equipment Manufacturer Model No Inventory No Cal Date Cal Due Date DC Power Supply ZhaoXin RXN-305D SEM Spectrum Analyzer Rohde & Schwarz FSP SEM Measurement Software JS Tonscend JS BT/WIFI V2. N/A N/A N/A Signal Generator Rohde & Schwarz SML03 SEM Power Meter Rohde & Schwarz NRVS SEM Coaxial Cable SGS N/A SEM Field Strength of the Fundamental Signal (15.231(b)) Equipment Manufacturer Model No Inventory No Cal Date Cal Due Date 3m Semi-Anechoic Chamber Measurement Software EMI Test Receiver BiConiLog Antenna ( MHz) Double-ridged horn (1-18GHz) Horn Antenna (18-26GHz) ETS-LINDGREN N/A SEM AUDIX Agilent Technologies e3 V N/A N/A N/A N9038A SEM ETS-LINDGREN 3142C SEM ETS-LINDGREN 3117 SEM ETS-LINDGREN 3160 SEM Coaxial Cable SGS N/A SEM

8 Page: 8 of 31 Radiated Emissions Equipment Manufacturer Model No Inventory No Cal Date Cal Due Date 3m Semi-Anechoic Chamber ETS-LINDGREN N/A SEM Measurement Software AUDIX e3 V N/A N/A N/A EMI Test Receiver Agilent Technologies N9038A SEM BiConiLog Antenna ( MHz) Double-ridged horn (1-18GHz) Horn Antenna (18-26GHz) ETS-LINDGREN 3142C SEM ETS-LINDGREN 3117 SEM ETS-LINDGREN 3160 SEM Coaxial Cable SGS N/A SEM General used equipment Equipment Manufacturer Model No Inventory No Cal Date Cal Due Date Humidity/ Temperature Indicator Humidity/ Temperature Indicator Humidity/ Temperature Indicator Barometer Shanghai Meteorological Industry Factory Shanghai Meteorological Industry Factory ZJ1-2B SEM ZJ1-2B SEM Mingle N/A SEM Changchun Meteorological Industry Factory DYM3 SEM

9 Page: 9 of 31 6 Radio Spectrum Technical Requirement 6.1 Antenna Requirement Test Requirement: 47 CFR Part 15, Subpart C Conclusion Standard Requirement: An intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. The use of a antenna that uses a unique coupling to the intentional radiator, the manufacturer may design the unit permanently attached antenna or of an so that a broken antenna can be replaced by the user, but the use of a standard antenna jack or electrical connector is prohibited. EUT Antenna: The antenna is integrated on the main PCB and no consideration of replacement. The best case gain of the antenna is 0dBi.

10 Page: 10 of 31 7 Radio Spectrum Matter Test Results dB Bandwidth Test Requirement 47 CFR Part 15, Subpart C (c) Test Method: ANSI C63.10 (2013) Section 6.9 Limit: Frequency range(mhz) Limit No wider than 0.25% of the center frequency Above 900 No wider than 0.5% of the center frequency E.U.T. Operation Operating Environment: Temperature: 25 C Humidity: 55 % RH Atmospheric Pressure: 1005 mbar Test mode a:tx mode_keep the EUT in transmitting with modulation mode Test Setup Diagram Measurement Procedure and Data 20dB bandwidth (MHz) Limit (MHz) Results N/A Pass

11 Page: 11 of 31 Test plot as follows: * RBW 3 khz * VBW 10 khz Marker 1 [T1 ] dbm Ref 10 dbm *Att 20 db SWT 10 ms MHz 10 ndb [T1] db BW khz 1 PK MAXH Temp 1 [T1 ndb] dbm MHz Temp 2 [T1 ndb] dbm A MHz T1 T DB Center MHz 5 khz/ Span 50 khz

12 Page: 12 of Dwell Time Test Requirement 47 CFR Part 15, Subpart C (a) Test Method: ANSI C63.10 (2013) Section Limit: Device type Manually operated transmitter Automatically actived transmitter Periodic transmissions to determine system integrity of transmitters used in security or safety applications Limit The switch automatically deactivate the transmitter within not more than 5 seconds of being released Cease transmission within 5 seconds after activation The total transmission time does not exceed 2 seconds per hour E.U.T. Operation Operating Environment: Temperature: 25 C Humidity: 55 % RH Atmospheric Pressure: 1005 mbar Test mode a:tx mode_keep the EUT in transmitting with modulation mode Test Setup Diagram Measurement Procedure and Data Measurement Data Test item Limit Results Transmitting time:0.304s 5S Pass

13 Page: 13 of 31 Test plot as follows: Ref -20 dbm Att 5 db RBW 1 MHz *VBW 1 MHz SWT 10 s Delta 1 [T1 ] 0.70 db ms Marker 1 [T1 ] dbm s A 1 PK MAXH DB Center MHz 1 s/ 7.3 Duty Cycle Test Requirement: Test Method: Test Setup: 47 CFR Part 15C Section (c) ANSI C63.10:2013 Limit: Test Mode: Instruments Used: Test Results: N/A Transmitting mode Refer to section 5 for details Pass

14 Page: 14 of 31 Test plot as follows: Duty cycle numbers Ref -15 dbm Att 20 db RBW 1 MHz * VBW 1 MHz SWT 100 ms 1 PK* CLRWR A SGL DB Center MHz 10 ms/ Ref -15 dbm Att 20 db RBW 1 MHz * VBW 1 MHz SWT 5 ms Delta 1 [T1 ] db µs 1 PK* CLRWR Marker 1 [T1 ] dbm ms 1 1 A SGL DB Center MHz 500 µs/

15 Page: 15 of 31 Ref -15 dbm Att 20 db RBW 1 MHz * VBW 1 MHz SWT 5 ms Delta 1 [T1 ] db µs 1 PK* CLRWR Marker 1 [T1 ] dbm ms A SGL DB Center MHz 500 µs/

16 Page: 16 of Spurious Emissions Test Requirement: 47 CFR Part 15C Section (b) Test Method: ANSI C63.10: 2013 Test Site: Receiver Setup: Limit: Limit: (Field strength of the fundamental signal) Test Setup: Measurement Distance: 3m (Semi-Anechoic Chamber) 3m (Fully-Anechoic Chamber) Frequency Detector RBW VBW Remark 0.009MHz-0.015MHz Quasi-peak 200Hz 1KHz Quasi-peak 0.015MHz-30MHz Quasi-peak 9kHz 30KHz Quasi-peak 30MHz-1GHz Quasi-peak 120 khz 300KHz Quasi-peak Above 1GHz Frequency Peak 1MHz 3MHz Peak Peak 1MHz 10Hz Average Field strength (microvolt/meter ) Limit (dbuv/m ) Remark Measurement distance (m) 0.009MHz-0.490MHz 2400/F(kHz) - Quasi-peak MHz-1.705MHz 24000/F(kHz) - Quasi-peak MHz-30MHz 30 - Quasi-peak 30 30MHz-88MHz Quasi-peak 3 88MHz-216MHz Quasi-peak 3 216MHz-960MHz Quasi-peak 3 960MHz-1GHz Quasi-peak 3 Above 1GHz Average Peak 3 Frequency Limit Remark MHz Average Value Peak Value Figure 1. Below 30MHz Figure 2. 30MHz to 1GHz

17 Page: 17 of 31 Figure 3. Above 1 GHz Test Procedure: a. For below 1GHz test, the EUT was placed on the top of a rotating table 0.8 meters above the ground at a 3 meter semi-anechoic camber. The table was rotated 360 degrees to determine the position of the highest radiation. Test Mode: Instruments Used: Test Results: b. For above 1GHz test, the EUT was placed on the top of a rotating table 1.5 meters above the ground at a 3 meter fully-anechoic camber. The table was rotated 360 degrees to determine the position of the highest radiation. c. The EUT was set 3 meters away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna tower. d. The antenna height is varied from one meter to four meters above the ground to determine the maximum value of the field strength. Both horizontal and vertical polarizations of the antenna are set to make the measurement. e. For each suspected emission, the EUT was arranged to its worst case and then the antenna was tuned to heights from 1 meter to 4 meters (for the test frequency of below 30MHz, the antenna was tuned to heights 1 meter) and the rotatable table was turned from 0 degrees to 360 degrees to find the maximum reading. f. The test-receiver system was set to Peak Detect Function and Specified Bandwidth with Maximum Hold Mode. g. If the emission level of the EUT in peak mode was 10dB lower than the limit specified, then testing could be stopped and the peak values of the EUT would be reported. Otherwise the emissions that did not have 10dB margin would be re-tested one by one using peak, quasi-peak or average method as specified and then reported in a data sheet. h. The radiation measurements are performed in X, Y, Z axis positioning. And found the X axis positioning which it is worse case, Only the test worst case mode is recorded in the report. Transmitting mode Refer to section 5 for details Pass

18 Page: 18 of 31 Measurement Data Field Strength Of The Fundamental Signal Average value: Calculate Formula: Test data: Average value=peak value + PDCF PDCF=20 log(duty cycle)= 20 log(42.35/100)=-7.46 Duty cycle= T on time / T period Ton time =(30* *0.85)=42.35ms T period =100ms Peak value: Frequency (MHz) Cable Loss (db) Antenna Factor (db/m) Preamp Factor (db) Read Level (dbuv) Level (dbuv/m) Limit Line (dbuv/m) Over Limit (db) Polarization Horizontal Vertical Average Value: Frequency (MHz) PCDF Average Level (dbuv/m) Limit Line (dbuv/m) Over Limit (db) Polarization Horizontal Vertical

19 Page: 19 of Radiated Emissions Test Requirement 47 CFR Part 15C Section Test Method: ANSI C63.10: 2013 Measurement Distance: 3m Limit: Frequency(MHz) Field strength(microvolts/meter) Measurement distance(meters) /F(kHz) /F(kHz) Remark: The emission limits shown in the above table are based on measurements employing a CISPR quasi-peak detector except for the frequency bands 9-90kHz and kHz. Radiated emission limits in these two bands are based on measurements employing an average detector.

20 Page: 20 of E.U.T. Operation Operating Environment: Temperature: 23 C Humidity: 54 % RH Atmospheric Pressure: 1005 mbar Test mode a:tx mode_keep the EUT in transmitting with modulation mode Test Setup Diagram Measurement Procedure and Data For testing performed with the loop antenna, the center of the loop was positioned 1 m above the ground and positioned with its plane vertical at the specified distance from the EUT. During testing the loop was rotated about its vertical axis for maximum response at each azimuth and also investigated with the loop positioned in the horizontal plane. Only the worst position of vertical was shown in the report.

21 Page: 21 of 31 Below 1GHz Mode:a; Polarization:Horizontal

22 Page: 22 of 31 Mode:a; Polarization:Vertical

23 Page: 23 of 31 Above 1GHz Mode:a; Polarization:Horizontal

24 Page: 24 of 31 Mode:a; Polarization:Vertical

25 Page: 25 of 31 8 Photographs 8.1 Field Strength of the Fundamental Signal (15.231(b)) Test Setup

26 Page: 26 of Radiated Emissions Test Setup

27 8.3 EUT Constructional Details Page: 27 of 31

28 Page: 28 of 31

29 Page: 29 of 31

30 Page: 30 of 31

31 Page: 31 of 31