DP800. Programmable Linear DC Power Supply RIGOL TECHNOLOGIES, INC.

Transcription

1 DP800 Programmable Linear DC Power Supply DP832A/832/83A:3 Outputs, CH CH2,CH3,Total Power up to 95W DP8A:40V/5A or 20V/0A,Single Channel,Dual Range with Remote Sense DP82A:60V/A 8V/0A,,Dual Channel with Remote Sense Low Ripple Noise: <350 uvrms/2mvpp Excellent Linear Regulation Rate and Load Regulation Rate Fast Transient Response Time: <50us Standard OVP/OCP/OTP protection functions Standard Timing function Built in V,A,W measurements and waveform display Support Output Delay, Analysis, Monitor, Preset functions Independent control for each channel 3.5 Inch TFT Display Connectivity: USB Host& Device, LAN, RS232, Digital IO, USB-GPIB(Opt.) RIGOL TECHNOLOGIES, INC.

2 DP800 Series Programmable DC Power Supply Larger LCD Display Intuitive User Intinterface Observable Clean Stable Reliable Affordable LCD Display Channel setting Parameter input Power button Output terminal Menu softkey Advanced function area Display Switching Complete Connectivity Product Dimension: Width Height Depth=239mm x 57mm x 48mm Weight: 9.75 kg Typical Applications R&D Iab General purpose testing Quality Assessment inspection Bias power for RF/MW circuits Automotive electronic test Production testing Device or circuit characterization and troubleshooting

3 Intuitive User Interface DP83A GUI DP832A GUI DP832 GUI Timing Output V/A/W Display Output Analysis Function Monitor Setup Trigger In/Out Output Delay LAN Setup

4 Specifications All the specifications are guaranteed when the instrument has been working for more than 30 minutes under the specified operation temperature. Unless otherwise noted, the specifications are applicable to all the channels of the specified model. DP832A/DP832/DP83A Specifications Model DP832A Channels DC Output (0 to 40 ) /current CH:0~30V/0~3A CH2:0~30V/0~3A CH3:0~5V/0~3A OVP/OCP CH:mV~33V/mA~3.3A CH2:mV~33V/mA~3.3A CH3:mV~5.5V/mA~3.3A Load Regulation Rate ±(Output Percentage + Offset) Linear Regulation Rate ±(Output ) Percentage + Offset) Ripples and Noise (20Hz to 20MHz) Normal Mode Normal Mode Annual Accuracy [] (25 ±5 ) ±(Output Percentage + Offset) Programming CH:0.05% + 20mV CH2:0.05% + 20mV CH3:0.% + 5mV CH:0.2% + 5mA CH2:0.2% + 5mA CH3:0.2% + 5mA Readback CH:0.05% + 0mV CH2:0.05% + 0mV CH3:0.% + 5mV CH:0.5%+ 5mA CH2:0.5%+ 5mA CH3:0.5%+ 5mA Resolution Programming mv 0mV With high-resolution option: mv ma ma 0mV Readback 0.mV With high-resolution option:0.mv ma 0.mA With high-resolution option:0.ma 0mV Display mv With high-resolution option:mv 0mA ma With high-resolution option:ma CH:0~8V/0~5A CH2:0~+30V/0~2A CH3:0~-30V/0~2A CH:mV~8.8V/0.mA~5.5A CH2:mV~33V/0.mA~2.2A CH3:-mV~-33V/0.mA~2.2A Transient Response Time Less than 50μs for output to recover to within 5mV following a change in output current from full load to half load or vice versa. Command Processing Time [2] <00ms Temperature Coefficient per (Output Percentage + Offset) CH/CH2:0.0%+5mV CH3:0.0%+2mV 0.0%+2mV 0.0%+2mA 0.02%+3mA Stability [3 ] ±(Output Percentage + Offset) <350μVrms/2mVpp <2mArms CH/CH2:0.02%+2mV CH3:0.0%+mV 0.05%+2mA Programming Control Speed (% within the total variation range) Rise Full Load CH/CH2:<50ms CH3:<ms No Load CH/CH2:<25ms CH3:<0ms DP832 3 CH:0mV~33V/mA~3.3A CH2:0mV~33V/mA~3.3A CH3:0mV~5.5V/mA~3.3A DP83A CH:0.%+5mV CH2:0.05%+20mV CH3:0.05%+20mV CH:0.2%+0mA CH2:0.2%+5mA CH3:0.2%+5mA CH:0.%+5mV CH2:0.05%+0mV CH3:0.05%+0mV CH:0.2%+0mA CH2:0.%+5mA CH3:0.%+5mA mv CH:0.3mA CH2/CH3:0.mA 0.mV 0.mA mv ma CH: 0.03%+mV CH2/CH3: 0.02% + 2mV CH: 0.%+3mA CH2/CH3: 0.05% + ma CH: <ms CH2/CH3: <50ms CH: <0ms CH2/CH3: <25ms

5 OVP/OCP Accuracy ±(Output Percentage + Offset) Activation Time Mechanical Dimensions Weight Power AC Input (50Hz to 60Hz) I/O USB Device USB Host LAN RS232 Digital IO USB-GPIB Environment Working Temperature Cooling Method Full Load No Load CH/CH2:<30ms CH3:<3ms CH/CH2:<400ms CH3:<200ms 0.5%+0.5V/0.5%+0.5A.5ms(OVP 3V) <0ms(OVP<3V 和 OCP) 239mm(W) x 57mm(H) x 48mm(D) 0.5kg (DP832A/DP832) 9.75kg (DP83A) 00Vac+0%,5Vac+0%,230Vac+0%(maximum 250VAC) Full Rated Value Output: 0 to 40 Under Relatively Higher Temperature: the linearity of the output current reducesdecreases linearly to 50% at the highest temperature 55 Fan Cooling Note: [] The accuracy parameters are acquired via calibration under 25 after -hour warm-up. [2] The maximum time required for the output to change accordingly after receiving the APPLy and SOURce commands. [3] The variation of the output within 8 hours after 30-minute warm-up when the load circuit and environment temperature are constant. CH: <3ms CH2/CH3: <30ms CH: <200ms CH2/CH3: <400ms DP8A Specifications Model Channels Output Scale 20V/0A(Low Range) DC Output (0 to 40 ) 0~+20V 0~0A OVP 0.V~22V OCP 0.A~A Load Regulation Rate ±(Output Percentage + Offset) Linear Regulation Rate ±(Output Percentage + Offset) Ripples and Noise (20Hz to 20MHz) Normal Mode Normal Mode <350μVrms/2mVpp <2mArms DP8A (2 output scales) 40V/5A(High Range) 0~+40V 0~5A 0.V~44V 0.V~5.5A Annual Accuracy [] (25 ±5 ) ±(Output Percentage + Offset) Programming 0.05%+0mV 0.%+0mA Readback 0.05% + 0mV 0.% + 0mA Resolution Programming Readback Display mv 0.5mA 0.mV 0.mA mv ma

6 Transient Response Time Less than 50μs for output to recover to within 5mV following a change in output current from full load to half load or vice versa. Command Processing Time [2] <00ms Temperature Coefficient per (Output Percentage + Offset) 0.0%+3mV 0.02%+3mA Stability [3] ±(Output Percentage + Offset) 0.02% + mv 0.% + ma Programming Control Speed (% within the total variation range) Rise Full Load No Load < 20 ms < 20 ms Fall Full Load <50ms No Load <400ms OVP/OCP Accuracy ±(Output Percentage + Offset) Activation Time Mechanical Dimensions Weight Power AC Input (50Hz to 60Hz) I/O USB Device USB Host LAN RS232 Digital IO USB-GPIB Environment Working Temperature Cooling Method 0.5%+0.5V/0.5%+0.5A.5ms(OVP 3V) <0ms(OVP<3V 和 OCP) 239mm(W) x 57mm(H) x 48mm(D) 0.3kg 00Vac+0%,5Vac+0%,230Vac+0%(maximum 250VAC) Full Rated Value Output: 0 to 40 Under Relatively Higher Temperature: the output current decreases linearly to 50% at the highest temperature 55 Fan Cooling Note: [] The accuracy parameters are acquired via calibration under 25 after -hour warm-up. [2] The maximum time required for the output to change accordingly after receiving the APPLy and SOURce commands. [3] The variation of the output within 8 hours after 30-minute warm-up when the load circuit and environment temperature are constant. DP82A Specifications Model Channels DC Output (0 to 40 ) 0~+8V 0~0A OVP 0.V~8.8V OCP 0.A~0.5A Load Regulation Rate ±(Output Percentage + Offset) Linear Regulation Rate ±(Output Percentage + Offset) Ripples and Noise (20Hz to 20MHz) Normal Mode Normal Mode 8V/0A <350μVrms/2mVpp <2mArms DP82A 2 60V/A 0~+60V 0~A 0.V~66V 0.A~.A

7 Annual Accuracy [] (25 ±5 ) ±(Output Percentage + Offset) Programming 8V/0A:<0.05%+0mV 60V/A:<0.%+25mV 0.2%+0mA Readback 8V/0A:0.05%+5mV 60V/A:<0.%+25mV 0.5%+0mA Resolution Programming Readback Display <00ms Temperature Coefficient per (Output Percentage + Offset) 0.0%+3mV 0.02%+3mA Stability [3] ±(Output Percentage + Offset) 0.02% + mv 0.% + ma Programming Control Speed (% within the total variation range) Rise Full Load No Load Fall Full Load No Load OVP/OCP Accuracy ±(Output Percentage + Offset) Activation Time Mechanical Dimensions Weight Power AC Input (50Hz to 60Hz) I/O USB Device USB Host LAN RS232 Environment Working Temperature Cooling Method 8V/0A:mV 60V/A:0mV 8V/0A:mA 60V/A:0.mA 60V/A:mV 8V/0A:mV 60V/A:0.mA 8V/0A:mA 60V/A:0mV 8V/0A:mV 60V/A:0.mA 8V/0A:mA Transient Response Time Less than 50μs for output to recover to within 5mV following a change in output current from full load to half load or vice versa. Command Processing Time [2] CH:<800ms CH2:<50ms <30ms <50ms CH:<800ms CH2:<400ms 0.5%+0.5V/0.5%+0.5A.5ms(OVP 3V) <0ms(OVP<3V 和 OCP) 239mm(W) x 57mm(H) x 48mm(D) 0kg 00Vac+0%,5Vac+0%,230Vac+0%(maximum 250VAC) Full Rated Value Output: 0 to 40 Under Relatively Higher Temperature: the output current decreases linearly to 50% at the highest temperature 55 or the input fuse is broken. Fan Cooling Note: [] The accuracy parameters are acquired via calibration under 25 after -hour warm-up. [2] The maximum time required for the output to change accordingly after receiving the APPLy and SOURce commands. [3] The variation of the output within 8 hours after 30-minute warm-up when the load circuit and environment temperature are constant.

8 Ordering Information Description Order Number Model Programmable DC Power (3 Channels) DP832A Programmable DC Power (3 Channels) DP832 Programmable DC Power (3 Channels) DP83A Programmable DC Power (2 Channels) DP82A Programmable DC Power ( Channel) DP8A Standard Accessories Power cord - USB data cable CB-USBA-USBB-FF-50 One shorted device - CD (including User s Guide and Programming Guide) - One fuse(50t-025h 250V 2.5A) - Quick Guide - al Accessories mv & ma High resolution option(dp832) HIRES-DP800 4 Lines Trigger In&Out(DP832) DIGITALIO-DP800 On-line Monitoring and analysis(dp832) AFK-DP800 RS232 and LAN interface(dp832) INTERFACE-DP800 USB to GPIB Converter USB-GPIB 2 Units Rack Mount Kit RM-2-DP800 Warranty Three -year warranty, excluding accessories. Headquarter RIGOL TECHNOLOGIES, INC. No.56,Cai He Village, Sha He Town, Chang Ping District, Beijing, P.R.China Tel: Fax: info@rigol.com USA RIGOL TECHNOLOGIES, USA INC. 740 First Place, Suite N Oakwood Village OH 4446, USA Toll free: RIGOL- Tel: Fax: beyondmeasure@ rigoltech.com Europe RIGOL TECHNOLOGIES EU, GmbH Lindbergh str Puchheim, Germany Tel: +49(0) info-europe@ rigoltech.com RIGOL is the registered trademark of RIGOL Technologies, Inc. Product information in this document subject to update without notice. For the latest information about RIGOL's products, applications and services, please contact local RIGOL office or access RIGOL official website: August,203