Technical Datasheet. D Series SMART Pressure Transmitter Model: DPC D-Series. Key Features. Series Overview. Product applications

Transcription

1 Technical Datasheet D Series SMART Pressure Transmitter Model: DPC-2000 Key Features ATEX - Flameproof and Intrinsically Safe IECEx - Flameproof and Intrinsically Safe SIL 2 certificate Compliant to NAMUR NE-43 High accuracy ±0.075% (better accuracy upon request) Fully HART compatible Static pressure limit up to 1200 bar 4-20mA, 0-20mA or 0-5mA analogue with digital communications Gold (Au) plated diaphragm option Hastelloy C276 wetted part option Programmable range, zero shift, characteristic and damping ratio with local panel keys Lighter weight Series Overview The pressure, differential pressure and temperature transmitters offer customers cost-effective and accurate solutions to their individual process requirements. Available with a wide range of process connections and easily configurable via the D-Soft software, the can be used for a variety of applications when pressure, differential pressure, temperature, level or flow measurements are needed. Other products in the series include: DPR-2200 SMART Differential Pressure Transmitter with 2 remote chemical seals DPR-2000G SMART Differential Pressure Transmitter for low range DPR-2000 SMART Differential Pressure Transmitter DPT-2000 SMART Temperature Transmitter Product applications The DPC-2000 is suitable for a wide range of applications in: Oil & Gas Chemical Petrochemical Power The choice of models available ensures that the DPC-2000 is suitable for use in: Corrosive atmospheres Resistant to chemical attack Model: DPC-2000ALW Page 1 of 5

2 Application & Construction TDS-DPC2000-C: MAY 2017 The DPC SMART Pressure Transmitters are suitable for measurement of pressure, under pressure, and absolute pressure of gases, vapours and liquids. The active sensing element is a piezoresistive silicon sensor separated from the medium by a diaphragm and by a specifically selected type of manometric liquid. The casing is made of cast aluminium alloy or 316 stainless steel with degree of protection IP66/67. The design of the casing enables the use of a local display, rotation of the display by 90, rotation of the casing by relative to the sensor, and a choice of cable direction. The communication standard for data interchange with the transmitter is the Hart protocol. Communication with the transmitter is carried out with: a KAP-03, KAP-03Ex communicator, some other Hart type communicators,(*) a PC using a HART/USB/Bluetooth converter and Raport 2 configuration software (*).eddl file available at The data interchange with the transmitter enables the users to: identify the transmitter; configure the output parameters: measurement units and the values of the start points and end points at the measurement range; damping time constant; conversion characteristic (inversion, user s non-linear characteristic); read the currently measured pressure value of the output current and the percentage output control level; force an output current with a set value; calibrate the transmitter in relation to a model pressure Installation The transmitter can be installed directly on the installation. A universal mounting bracket is provided to transmitter fitting on 2" pipe. When the pressure of steam or other hot media is measured, a siphon or impulse line should be used. The needle valve placed upstream the transmitter simplifies installation process and enables the zero point adjustment or the transmitter replacement. When the special process connections are required for the measurement of levels and pressures (e.g. at food and chemical industries), the transmitter is provided with a diaphragm seal. The transmitter s electrical connections should be performed with twisted cable. The place for the communicator should be assigned before the communicator installation. No. Measuring Ranges Nominal measuring range (FSO) Minimum set range Rangeability Overpressure limit (without hysteresis)*** bar (0 100 MPa) 10 bar (1 MPa) 100: bar (120 MPa) bar ( MPa) 3 bar (300 kpa) 100:1 450 bar (45 MPa) bar (0 16 MPa) 1,6 bar (160 kpa) 100:1 450 bar (45 MPa) bar (0...7 MPa) 0,7 bar (70 kpa) 100:1 140 bar (14 MPa) bar (0...2,5 MPa) 0,25 bar (25 kpa) 100:1 50 bar (5 MPa) bar (0...0,7 MPa) 0,07 bar (7 kpa) 100:1 14 bar (1,4 MPa) 7-1 7bar ( kpa) 0.07 bar (7 kpa) 114:1 14 bar (1,4 MPa) bar ( kpa) 100 mbar (10 kpa) 20:1 4 bar (400 kpa) bar ( kpa) 50 mbar (5 kpa) 20:1 2 bar (200 kpa) 10-0,5...0,5 bar ( kpa) 50 mbar (5 kpa) 20:1 2 bar (200 kpa) ,25 bar ( kpa) 25 mbar (2.5 kpa) 10:1 1 bar (100 kpa) mbar ( kpa) 20 mbar (2 kpa) 10:1 1 bar (100 kpa) mbar * (-1,5...7 kpa) 5 mbar (0.5 kpa) 17:1 0.5 bar (50 kpa) bar abs ( kpa abs) 100 mbar abs (10 kpa abs) 13:1 2 bar (200 kpa) bar abs ( MPa abs) 100 mbar abs (10 kpa abs) 70:1 14 bar (1.4 MPa) bar abs ( MPa abs) 0.25 bar abs (25 kpa abs) 100:1 50 bar (5 MPa) bar abs (0...7 MPa abs) 0.7 bar abs (70 kpa abs) 100:1 140 bar (14 MPa) *only for transmitters without diaphragm seal Measurement of lower pressure ranges, possible using transmitter DPR-2000GALW with GP process connection Model: DPC-2000ALW Technical Data Accuracy ±0.075% of the calibrated range Long-term stability accuracy for 3 years (for the nominal measuring range) Thermal error < ±0.05% (FSO) / 10 C (0.1% for ranges 12, 13) max. ±0.25% (FSO) in the whole compensation range (0.4% for ranges 12, 13) Metrological Parameters Thermal compensation range Additional electronic damping Error due to supply voltage changes C C special version s 0.002% (FSO) / V Page 2 of 5

3 TDS-DPC2000-C: MAY 2017 Technical Data (cont.) Electrical parameters Power supply: Model DPC-2000ALW V DC (Ex ia 13, V) ( Ex d 13,5 45V) Model DPC-2000ALE V DC Additional voltage drop when display Illumination switched on Output signal Special Version: 3V ma, two wire transmission or 0...5, [ma] Load resistance Resistance required for communication * - 15 V when display illumination switched on W Materials Wetted parts and 316LSS, Hastelloy C 276, Au Diaphragms Casing Aluminium, 316SS Material of window Polycarbonate glass, hardened glass Operating conditions Accuracy depending on the set range Operating temperature range (ambient temp.) C Ex i version C Ex d version C Medium temperature range C over 120 C measurement with the use of impulse line or diaphragm seals CAUTION: the medium must not be allowed to freeze in the impulse line or close to the process connection of the transmitter Measurements in the hazardous areas For pressure measurements in the areas under explosion hazard the ATEX intrinsically safe transmitters, II 1/2G Ex ia IIB T5 G a/gb are available Technical data Metrological parameters, materials of process connection, diaphragms and casing, and operating conditions see the description on previous page. Electrical parameters Power supply (from DP/PA coupler ) V DC V DC - when display illumination switched on. Power supply from intrinsically-safe coupler according to FISCO requirements. Vi=15VDC Ii=0.38A for IIB Current consumption 14mA Electrical diagrams for transmitters Model: DPC-2000ALW Page 3 of 5

4 TDS-DPC2000-C: MAY 2017 Dimensions Model: DPC-2000ALW Page 4 of 5

5 TDS-DPC2000-C: MAY 2017 Model: DPC-2000ALW DPC-2000 Casing, output signal Model Code Description Versions, certificates* *more than one option is available Nominal measuring range **non-standard ranges available on request Process connections Electrical connection Accessories *more than one option is available Other specification How to Order ALW... ALE ALW/SS. /Exia /Exia (Da).. /Exd /Exd (2G)... /SA.. /Safety /HS.. /0,05%... /Tlen / C... /IP /0 1000bar**... /0 300bar... /0 160bar**... /0 70bar... /0 25bar... /0 7bar... /0 2bar... /0 1bar... /0 0,25bar... /-0,5 0,5bar... /-1 6bar... / mbar... /-15 70mbar... /0 1,3bar ABS... /0 7bar ABS... /0 25bar ABS... /0 70bar ABS... /M /M (Au) /G1/2.. /G1/2 (Au)... /G1/4. /P. /P (Hastelloy). /GP.. /GP (Hastelloy).. /CM30x2. /CM30x2(Hastelloy)... /CG1... /CG1/2... /1/2 NPTM... /1/2 NPTF... /code of diaphragm seal.. (without marking)... /US... /AL.. /AL..(SS) /ST.. /MT.. / Smart pressure transmitter Aluminum housing, IP66/IP67, with display, output 4-20mA + Hart Aluminum housing, IP66/IP67, with display, output 4-20mA + Hart 0 20mA+ Hart, 0 5mA+ Hart, Stainless steel housing, IP66/IP67, with display, output 4-20mA + Hart II 1/2G Ex ia IIC T5/T6 Ga/Gb II 1/2G Ex ia IIB T5/T6 Ga/Gb (version with Teflon-Shielded Cable) IECEx Ex ia IIC T4/T5 Ga/Gb IECEx Ex ia IIB T4/T5 Ga/Gb (version with Teflon-Shielded Cable) II 1/2G Ex ia IIC T5/T6 Ga/Gb II 1/2G Ex ia IIB T5/T6 Ga/Gb (version with Teflon-Shielded Cable) I M1 Ex ia I Ma (version with Enclosure SS316) II 1D Ex ia IIIC T105 C Da IECEx Ex ia IIC T4/T5 Ga/Gb IECEx Ex ia IIB T4/T5 Ga/Gb (version with Teflon-Shielded Cable) IECEx Ex ia I Ma (version with Enclosure SS316) IECEx Ex ia IIIC T105 C Da II 1/2G Ex ia/d IIC T6/T5 Ga/Gb II 1/2D Ex ia/t IIIC T85 C/T100 C Da/Db I M2 Ex db ia I Mb IECEx Ex ia/db IIC T6/T5 Ga/Gb IECEx Ex ia/t IIIC T85 C/T100 C Da/Db IECEx Ex db ia I Mb II 2G Ex ia/d IIC T6/T5 Gb II 2D Ex ia/t IIIC T85 C/T100 C Db IECEx Ex ia/db IIC T6/T5 Gb IECEx Ex ia/t IIIC T85 C/T100 C Db Packing gland available on request Packing gland available on request Surge arrester for Exia version SIL2 - Functional Safety certificate according to PN-EN :2010; PN-EN :2010; PN-EN :2010; PN-EN :2007; PN-EN 62061:2008+A1 not available for ranges no Ultra stable version (only ranges no. 13 to 16) Accuracy L ±0,05% For oxygen service (sensor filled with Fluorolube fluid), only M and G1/2 connection Extended thermal compensation range Protection class IP67 Range bar (0 100MPa) 0 300bar (0 30MPa) 0 160bar (0 16MPa) 0 70bar (0 7MPa) 0 0,25bar (0 2,5MPa) 0 7bar (0 700KPa) 0 2bar (0 200kPa) 0 1bar (0 100kPa) 0 0,25bar (0 25kPa) -0,5 0,5bar (-50 50kPa) -1 6bar ( kPa) mbar (-10 10kPa) mbar (-1,5 7kPa) 0 1,3bar absolute pressure (0 130kPa abs) 0 7bar absolute pressure (0 700kPa abs) 0 25bar absolute pressure (0 2.5MPa abs) 0 70bar absolute pressure (0 7MPa abs) Measuring set range / + (required units) Calibrated range in relation to 4mA and 20mA output Min. set range 10bar (1MPa) 3bar (300kPa) 1,6 bar (160kPa) 0,7bar (70kPa) 0,25bar (25kPa) 0,07bar(7kPa) 100mbar (10kPa) 50mbar (5kPa) 25mbar (2.5kPa) 50mbar (5kPa) 300mbar (30kPa) 20mbar (2kPa) 5mbar (0,5kPa) 50mbar abs (5kPa abs) 0,07bar abs (7kPa abs) 0,25bar abs (25kPa abs) 0,7bar abs (70kPa abs) Thread M20x1,5 (male) with Ø4 hole, wetted parts SS316L Thread M20x1,5 (male) with Ø4 hole, gold plated diaphragm (range no. 1, 2, 3, 4) Thread G1/2 (male) with Ø4 hole, wetted parts SS316L Thread G1/2 (male) with Ø4 hole, gold plated diaphragm (range no. 1, 2, 3, 4) Thread G1/4 (male), wetted parts SS316L (Pressure limits: min. 10 mbar / max 350 bar) Thread M20x1,5 (male) with Ø12 hole, wetted parts SS316L (N/A with range 1, 2) Thread M20x1,5 (male) with Ø12 hole, wetted parts Hastelloy C 276 (N/A with range 1, 2) Thread G1/2 (male) with Ø12 hole, wetted parts SS316L (N/A with range 1, 2) Thread G1/2 (male) with Ø12 hole, wetted parts Hastelloy C 276 (N/A with range 1, 2) Thread M30x2 with flush diaphragm, wetted parts SS316L (Pressure: min. 0,1bar / max. 70bar) Thread M30x2 with flush diaphragm, wetted parts Hastelloy C 276 (Pressure limits: min. 0,1bar / max. 70bar) Thread G1 with flush diaphragm, wetted parts SS316L (Pressure limits: min. 0,1bar / max. 70bar) Thread G1/2 with flush diaphragm, wetted parts SS316L (Pressure limits: min. 2,5bar / max. 300bar) Thread 1/2 NPT Male, wetted parts SS316L Thread M20x1,5 with adapter to 1/2 NPT Female, wetted parts SS316L Diaphragm seal (see chapter of diaphragm seals) Packing gland M20x1.5 Thread 1/2NPT Female Mounting bracket type AL for 2 pipe, material zinced steel Mounting bracket type AL for 2 pipe, material stainless steel Stainless Steel plate riveted to the housing Stainless Steel Tag plate mounted on wire Description of required parameters (e.g. non-standard process connection G3/4, M22x1.5 The most typical specification is marked by mark. Example: Pressure transmitter with display, output 4..20mA + HART, version EExia, nominal measuring range 0..25bar, calibrated range 0..16bar, process connection G1/2, electrical connection 1/2NPT F, mounting bracket for 2 pipe DPC-2000ALW/EExia/0..25bar/0..16bar/G1/2/US/AL In the interest of development and improvement Delta Controls Ltd, reserves the right to amend, without notice, details contained in this publication. No legal liability will be accepted by Delta Controls Ltd for any errors, omissions or amendments. Delta Controls Limited Riverside Business Park, Dogflud Way, Farnham, Surrey GU9 7SS, UK. T+44 (0) F+44 (0) E sales@delta-controls.com W Page 5 of 5

6 Technical Datasheet D Series SMART Differential Pressure Transmitter Model: DPR-2000 Key Features ATEX - Flameproof and Intrinsically Safe IECEx - Flameproof and Intrinsically Safe SIL 2 certificate Compliant to NAMUR NE-43 High accuracy ±0.075% (better accuracy upon request) Fully HART compatible Static pressure limit up to 420 bar 4-20mA, 0-20mA or 0-5mA analogue with digital communications Gold (Au) plated diaphragm option Hastelloy C276 wetted parts option Programmable range, zero shift, characteristic and damping ratio with local panel keys Series Overview The pressure, differential pressure and temperature transmitters offer customers cost-effective and accurate solutions to their individual process requirements. Available with a wide range of process connections and easily configurable via the D-Soft software, the can be used for a variety of applications when pressure, differential pressure, temperature, level or flow measurements are needed. Product applications The DPR-2000 is suitable for a wide range of applications for measuring: Differential Pressure Level Flow The choice of models available ensures that the DPR-2000 is suitable for use in: Corrosive atmospheres Resistant to chemical attack Other products in the series include: DPR-2200 SMART Differential Pressure Transmitter with 2 remote chemical seals DPR-2000G SMART Differential Pressure Transmitter for low range DPC-2000 SMART Pressure Transmitter DPT-2000 SMART Temperature Transmitter Model: DPR-2000ALW Page 1 of 4

7 Application & Construction TDS-DPR2000-C: MAY 2017 The DPR SMART Differential Pressure Transmitters are suitable for measuring differential pressure of gases, vapours and liquids. The active sensing element is a piezoresistive silicon sensor separated from the medium by a diaphragm and by a specifically selected type of manometric liquid. The casing is made of cast aluminium alloy or 316 stainless steel with degree of protection IP66/67. The design of the casing enables the use of a local display, rotation of the display by 90, rotation of the casing by relative to the sensor, and a choice of cable direction. The communication standard for data interchange with the transmitter is the Hart protocol. Communication with the transmitter is carried out with: a KAP-03, KAP-03Ex communicator, some other Hart type communicators,(*) a PC using a HART/USB/Bluetooth converter and D-Soft configuration software (*).eddl file available at Installation Measuring Ranges The data interchange with the transmitter enables the users to: identify the transmitter; configure the output parameters: measurement units and the values of the start points and end points at the measurement range; damping time constant; conversion characteristic (inversion, user s non-linear characteristic); read the currently measured pressure value of the output current and the percentage output control level; force an output current with a set value; calibrate the transmitter in relation to a model pressure The transmitter with P or PN type process connection is not heavy, so it can be installed without an additional mounting bracket on application. For fitting in any desired position we recommend a universal Delta mounting bracket for 2" pipe (AL mounting bracket). The version with C type process connections can be fitted directly to a 3- or 5- valve manifold. We recommend factory-mounted transmitters with VM type valve manifold. A transmitter without a valve manifold can be fitted in any position on a 2 pipe or on a wall using the C-2" mounting bracket. When the special process connections are required for the measurement of specific media levels in closed tanks (e.g. in the sugar and chemical industries) the transmitter is fitted with a Delta diaphragm seal. No. Nominal measuring range (FSO) Minimum set range Rangeability bar (0...7 MPa) 7 bar (700 kpa) 10:1 Overpressure limit/ Static pressure limit bar* (0...1,6MPa) 1,6 bar (160 kpa) 10: ,5 bar ( kpa) 0,2 bar (20 kpa) 12,5: bar* ( kpa) 50 mbar (5 kpa) 20:1 C-type: 250/320/420 bar ,25 bar ( kpa) 10 mbar (1 kpa) 25:1 P-type: 40 bar (for range no. 1:70 bar 6-0,5...0,5 bar* ( kpa) 0,1 bar (10 kpa) 10: mbar * ( kpa) 10 mbar (1 kpa) 20: mbar* (-0,5...7 kpa) 4 mbar (0,4 kpa) 18: mbar* (-2,5...2,5 kpa) 2 mbar (0,2 kpa) 25:1 C-type : 200 bar P-type: 40 bar mbar** ( Pa) 1 mbar (0,1 kpa) 14:1 20 bar *available also in HS version **available only in HS version HS version with Exd certificate available from Q3/2016 Technical Data Accuracy Metrological parameters ±0.075% of the calibrated range ±0.1% of calibrated range ( range no. 9) Long-term stability (for the nominal measuring range) accuracy for 3 years Electrical parameters Power supply: Model DPR-2000ALW V DC (Ex ia 13, V) (Ex d 13,5 45V) Model DPR-2000ALE V DC Model: DPR-2000ALW Thermal error for ranges no 1-8 ±0.05% (FSO) / 10 C for ranges no 9 ±0.08% (FSO) / 10 C max. ±0.3% (FSO) in temperature range C special version for ranges no 1-8 ±0.03% (FSO) / 10 C max. ±0.1% (FSO) in temperature range C Thermal compensation range C Zero shift error for 0.01% (FSO) / 10 bar for range 3, 4, 5, 6 static pressure 0.03% (FSO) / 10 bar for range 1, 7, % (FSO) / 10 bar for ranges 2, 7 Zeroing the transmitter in conditions of static pressure can eliminate this error. Additional electronic damping 0 60 s Error due to supply voltage changes 0.002% (FSO) / V Additional voltage drop when display illumination switched on 3 V Output signal ma, two wire transmission DPR-2000ALE: 0 20 or 0 5, 4 20 [ma] Load resistance * -15V when display illumination switched on Resistance required for communication W Page 2 of 4

8 TDS-DPR2000-C: MAY 2017 Technical Data (cont.) Materials Wetted parts: type P, PN process connection: 316Lss type P(H) process connection: Hastelloy C276 type C process connection: 316ss Diaphragms: 316Lss, Hastelloy C 276, Au Casing : Aluminium Option : 316SS Material of window: polycarbonate glass, hardened glass Operating conditions Operating temperature range (ambient temp.) C Exi version C Exd version C Medium temperature range C over 120 C measurement with the use of impulse line or diaphragm seals CAUTION: the medium must not be allowed to freeze in the impulse line or close to the process connection of the transmitter Accuracy depending on the set range Electrical diagrams Electrical diagrams for transmitters with HART protocol Dimensions Model: DPR-2000ALW Page 3 of 4

9 TDS-DPR2000-C: MAY 2017 How to Order Model: DPR-2000ALW DPR-2000 Casing, output signal Model Code Description Versions, certificates* *more than one option is available Nominal measuring range ALW... ALE ALW/SS. /Exia /Exia (Da)... /Exd /Exd (2G)... /SA.. /Safety /HS.. /0,05%... /Tlen /320 bar..... /420 bar. /IP /0 70bar... /0 16bar... /0 2,5bar... /0 1bar... /0 0,25bar... /-0,5 0,5bar... /-0,1 0,1bar... /-5 70mbar... /-25 25mbar... /-7 7mbar... Smart differential pressure transmitter Aluminum housing, IP66, with display, output 4-20mA + Hart Aluminum housing, IP66, with display, 0-20mA, 0-5mA+ Hart, Exia and Exd version not available Stainless steel housing IP66, with display, output 4-20mA + Hart II 1/2G Ex ia IIC T5/T6 Ga/Gb II 1/2G Ex ia IIB T5/T6 Ga/Gb (version with Teflon-Shielded Cable) IECEx Ex ia IIC T4/T5 Ga/Gb IECEx Ex ia IIB T4/T5 Ga/Gb (version with Teflon-Shielded Cable) II 1/2G Ex ia IIC T5/T6 Ga/Gb II 1/2G Ex ia IIB T5/T6 Ga/Gb (version with Teflon-Shielded Cable) I M1 Ex ia I Ma (version with Enclosure SS316) II 1D Ex ia IIIC T105 C Da IECEx Ex ia IIC T4/T5 Ga/Gb IECEx Ex ia IIB T4/T5 Ga/Gb (version with Teflon-Shielded Cable) IECEx Ex ia I Ma (version with Enclosure SS316) IECEx Ex ia IIIC T105 C Da II 1/2G Ex ia/d IIC T6/T5 Ga/Gb II 1/2D Ex ia/t IIIC T85 C/T100 C Da/Db I M2 Ex ia I Mb IECEx Ex ia/db IIC T6/T5 Ga/Gb IECEx Ex ia/t IIIC T85 C/T100 C Da/Db IECEx Ex db ia I Mb II 1/2G Ex ia/d IIC T6/T5 Ga/Gb II 1/2D Ex ia/t IIIC T85 C/T100 C Da/Db I M2 Ex ia I Mb IECEx Ex ia/db IIC T6/T5 Gb IECEx Ex ia/t IIIC T85 C/T100 C Db Packing gland available on request Packing gland available on request Surge arrester for Exia version SIL2 - Functional Safety certificate according to PN-EN :2010; PN-EN :2010; PN-EN :2010; PN-EN :2003; PN-EN 62061:2005+A1 Ultra stable version (only ranges no. 2, 4 to 10) Accuracy L ±0,05% For oxygen service (sensor filled with Fluorolube fluid) Static pressure 320 bar, only for C process connection Static pressure 420 bar, only for C process connection Protection class IP67 Range Min. set range 0 70bar (0 7000kPa) 0 16bar (0 1600kPa) 0 2,5bar (0 250kPa) 0 1bar (0 100kPa) 0 0,25bar (0 25kPa) -0,5 0,5bar (-50 50kPa) -1 0,1bar (-10 10kPa) -5 70mbar (-0,5 7kPa) mbar (-2,5 2,5kPa) -7 7mbar (-0,7 0,7kPa) Measuring set range / + (required units) Calibrated range in relation to 4mA and 20mA output Process connections Process connection C available with NACE MR certificate Material of diaphragms (refers only to C, CR, P, PN process connection) Gasket (refers only to C, CR process connection) Electrical connection Accessories* *more than one options is available. /C /CR.. /P. /PN..... /code of diaphragm seal... (without marking)... /(H)... /(Au)..... (without marking)... /NBR... /PTFE (without marking)... /US... /C-2... /C-2 (SS)... /FI25.. /RedSpaw P. /RedSpaw C.. /Red d/p 1/2 /ST... /MT... 7bar (700kPa) 1,6bar (160kPa) 0,2bar (20kPa) 50mbar (5kPa) 10mbar (1kPa) 0,1bar (10kPa) 10mbar (1kPa) 4mbar (0,4kPa) 2mbar (0,2kPa) 1mbar (0,1kPa) Thread 1/4 NPT F on the cover flanges cover flanges material SS316. Allows mounting with a valve manifold. Process connection of cover flange: M10 (option /C(7/16) - 7/16 UNF acc. to IEC 61518) C-type process connection rotated 90 Thread M20x1,5 (male) Thread 1/4 NPT (female) Diaphragm seal (see chapter of diaphragm seals) mounted on Hi side of transmitter, Lo side 1/4 NPT Female Diaphragms material SS316L Diaphragms material Hastelloy C276 (/P and /PN all wetted parts in Hastelloy C276 on request) (not available for transmitters in HS version) Gold plated diaphragms (not available for transmitters in HS version) FPM Viton NBR (for oxygen service) PTFE Packing gland M20x1.5 Thread 1/2NPT Female Mounting bracket for 2 pipe (to C process conn.), mat. zinced steel Mounting bracket for 2 pipe (to C process conn.), mat. Stainless Steel Mounting bracket for 2 pipe (to P process conn.), mat. Stainless Steel Connector to weld impulse pipes dia. 12 and 14 mm, material 15HM(SO) or SS316(S). Only process connection P type Connector to weld impulse pipes dia. 12 and 14 mm, material 15HM. Only process connection C type. Adapter for differential pressure transmitters with C type process connection, output thread 1/2NPT F. Material SS316L Stainless Steel plate riveted to the housing Stainless Steel Tag plate mounted on wire Other specification /. Description of required parameters (e.g. IP66/67) Example: Differential pressure transmitter with display, output 4..20mA + HART, version EExia, nominal measuring range 0..2,5bar, calibrated range 0..1,5bar, process connection G1/2, electrical connection 1/2NPT F, mounting bracket for 2 pipe DPR-2000ALW/EExia/0..2,5bar/0..1,5bar/G1/2/US/AL In the interest of development and improvement Delta Controls Ltd, reserves the right to amend, without notice, details contained in this publication. No legal liability will be accepted by Delta Controls Ltd for any errors, omissions or amendments. Delta Controls Limited Riverside Business Park, Dogflud Way, Farnham, Surrey GU9 7SS, UK. T+44 (0) F+44 (0) E sales@delta-controls.com W Page 4 of 4

10 Technical Datasheet SMART Temperature Transmitter Models: DPT-2000 Key Features Ÿ High accuracy ±0.075% Ÿ 4-20mA analogue with digital communications Ÿ Fully HART compatible Ÿ Programmable range, zero shift, characteristic and damping ratio with local panel keys Ÿ ATEX certified (Intrinsic Safety, Flameproof) Series Overview The pressure, differential pressure and temperature transmitters offer customers cost-effective and accurate solutions to their individual process requirements. Available with a wide range of process connections and easily configurable via the D-Soft software, the can be used for a variety of applications when pressure, differential pressure, temperature, level or flow measurements are needed. Product Applications The DPT-2000 is suitable for a wide range of applications in many industry sectors: Ÿ Oil & Gas Ÿ Petrochemical Other models in this series include: DPR-2000G SMART Differential Pressure Transmitter for low range Ÿ Water & Wastewater Ÿ Power DPR-2200 SMART Differential Pressure Transmitter with 2 remote chemical seals The choice of models available Ÿ DPC-2000 SMART Pressure Transmitter Ÿ DPR-2000 SMART Differential Pressure Transmitter Ÿ Suitable for use in corrosive atmospheres ensures that the DPT-2000 is: Ÿ Resistant to chemical attack Ÿ Models: DPT-2000ALW Ÿ

11 Technical Data Metrological parameters Error (digital value) ± ( % z t ) C for sensor Pt100 ± ( % z) C for sensor K i t L 375 C ± ( % z (t-375)) C for sensor K i t > 375 C Additional error for analog output ±0.04% z where: t absolute value of the measured temperature C t - value of the measured temperature C z transmitter setting range C Resistance required for communication (HART) min. 240W. U [ V ] - 12V * R[W] = Min set range Pt100 K 10 C 10 C 0,0225A 15 V when display illumination switched on Operating conditions Measuring range Sensor type ZAS Load resistance Nominal range C C Ambient temperature for version with Ex ia for version with Ex d C C ºC Min. immersion length L=100mm Materials Casing Sensor material Thermowell Aluminium, 316Lss- special version 321ss according to table page. Electrical parameters Communication and configuration Power supply V DC (Ex V) Additional voltage drop when display illumination switched on 3 V Output signal ATEX certificate The communication standard for data interchange with the transmitter is the Hart protocol. Communication with the transmitter is carried out with: a KAP-03, KAP-03Ex communicator, some other Hart type communicators, a PC using an Hart/RS/Bluetooth converter and Delta s D-Soft configuration software ma + Hart protocol Ex ia Coming Soon! not available Ex I M2 Ex d ia I Mb (steel enclosure only) Ex II 1/2G Ex ia/d IIC T* Ga/Gb Ex II 1/2D Ex ia/t IIIC T* Da/Db Exd The data interchange with the transmitter enables the users to: identify the transmitter; configure the output parameters: read the currently measured temperature value of the output current and the percentage output control level; force an output current with a set value; calibrate the transmitter in relation to a model temperature. for ALE Electrical diagram RS-HART converter or communicator Power supply Milliammeter 4 20 ma ma TEST TEST Jumper SIGNAL Transmitter 240 Ωhm Standard Thermowell Data Models: DPT-2000ALW Thermowell type Standard dimensions of thermowell OG2.9 Ø[mm] 9x1 OG x2 T1 11x2 SW1/SW2 18h7/24h7 L[mm] 100, 160, 250, , 160, 250, , 160, 250, , 200 SW1T/SW2T 18h7/24h7 100, 140, 200 I[mm] - Thermowell material Avaliable process connection 316Lss M20x1.5, M27x1 G½, G¾, ½ NPT M20x1.5, M27x1 G½, G¾, ½ NPT Flange according to DIN and ANSI Lss - 316Lss 65, 65 15HM, 10H2M 316Lss 15HM, 10H2M 316Lss 35, 65, 65 Flange according to DIN and ANSI

12 Dimensions Packing gland M20 1.5, cabel excision for key 24mm knurled nut connecting sensor and transmitter 165 M lub G1/2" M or G1/2" M or M DPT-2000ALW/WW DPT-2000ALW/GN Version M lub M M lub G1/2" M lub G1/2" Flange according to: PN, DIN, or ANSI Flange according to: PN, DIN, or ANSI M lub G1/2" M27 2 lub G1 F 6,9,11 L l 6,9,11 L DPT-2000ALW/GN version with spring loaded sensor to screwing in thermowell. - standard version - Exia version - Exd version Thermowell L DPT-2000ALW/GB version with spring loaded sensor to screwing in thermowell. - standard version - Exia version - Exd version - MID version DPT-2000ALW/NC l DPT-2000ALW/GB Ø3 or Ø6 L Ø3 or Ø6 L L M or G1/2" M or M DPT-2000ALW/WW - version with replaceable measuring sensor. T1 SW1 / SW2 SW1T / SW2T Models: DPT-2000ALW OG2.9 / OG2.11 DPT-2000ALW/WW - version suitable for mounting cable sensor.

13 How to Order DPT-2000ALW/ / / / / L =... mm / / C/ Special version: Ex ia - ATEX certificate Ex d - ATEX certificate Coming Soon! not available Ex I M2 Ex d ia I Mb (steel enclosure only) Ex II 1/2G Ex ia/d IIC T* Ga/Gb Ex II 1/2D Ex ia/t IIIC T* Da/Db for ALE SS - Housing material 316SS Ip67 Enclosure Version: GB, GN, WW, NC Thermowell type: according to table Type of thread of flange connection: M20 1,5; G1/2"; M27 2; G1" or flange Immersion length Type of measuring element: Pt100, K Set measuring range Alarm signal: 3,8 or 23 ma Example: Temperature transmitter DPT-2000ALW thermowell type T1, ATEX version Ex ia, immersion length 250mm, flange DN50 PN40, K type sensor, set range C, alarm signal 23 ma Models: DPT-2000ALW DPT-2000ALW/ Ex ia/gn/t1/dn50/l=250 mm / DN50 PN40 / K / C / 23 ma In the interest of development and improvement Delta Controls Ltd, reserves the right to amend, without notice, details contained in this publication. No legal liability will be accepted by Delta Controls Ltd for any errors, omissions or amendments. Delta Controls Limited Riverside Business Park, Dogflud Way, Farnham, Surrey GU9 7SS, UK. T+44 (0) F+44 (0) E sales@delta-controls.com W