HA1SV W DC/DC Power Modules

Transcription

1 HA1SV W DC/DC Power Modules FEATURES High efficiency : full load Size:61.0mm*57.9mm*12.7mm(2.4 *2.28 *0.5 ) Industry standard pin out and footprint Fixed frequency operation Input UVP/ OVP Hiccup output over current protection (OCP) Hiccup output over voltage protection (OVP) Output current limited protection(ocl) Auto recovery OTP Monotonic startup into normal 3000V isolation and reinforce insulation No minimum load required ISO 9001, TL 9000, ISO 14001, QS9000, OHSAS18001 certified manufacturing facility EN50155,EN61373 EN :2006,UL ,CSA-C22.2 Delphi Series HA1SV12, half Brick Family DC/DC Power Modules: 53~154V in, 12V/8.3A out, 100W The Delphi Module HA1SV12008PRFA, half brick, 53~154V input, single output, isolated DC/DC converter is the latest offering from a world leader in power system and technology and manufacturing Delta Electronics, Inc. This product provides up to 100 watts power in an industry standard footprint and pin out. With creative design technology and optimization of component placement, these converters possess outstanding electrical and thermal performances, as well as extremely high reliability under highly stressful operating conditions. The HA1SV12008PRFA offers more than 84% high efficiency at 5A load in all input voltage range. APPLICATIONS Railway /Transportation system DATASHEET P1

2 TECHNICAL SPECIFICATIONS PARAMETER NOTES and CONDITIONS HA1SV12008PRFA Min. Typ. Max. Units 1. ABSOLUTE MAXIMUM RATINGS 1.1 Input Voltage EN Vdc 1.2 Input surge withstand <100ms 250 Vdc 1.3 Operating Ambient Temperature C 1.4 Storage Temperature C 1.5 Input/Output Isolation Voltage reinforce 3000 Vrms 2. INPUT CHARACTERISTICS 2.1 Operating Input Voltage Vdc 2.2 Input Under-Voltage Lockout Turn-On Voltage Threshold Vdc Turn-Off Voltage Threshold Vdc 2.3 Input Over-Voltage Lockout Turn-On Voltage Threshold Vdc Turn-Off Voltage Threshold Vdc 2.4 Maximum Input Current Full Load, 53Vin A 2.5 No-Load Input Current Vin=110V, Io=0A ma 2.6 Off Converter Input Current Vin=110V ma 2.7 Input Reflected-Ripple Current(pk-pk) Vin=110V, Io=full load,cin=150uf/400v 35 ma 3. OUTPUT CHARACTERISTICS 3.1 Output Voltage Set Point Vin=110V, Io=0, Tc=25 C Vdc Load regulation Vin=110V, Io=Io min to Io max ±0.05 ±0.2 % Line regulation Vin=53V to154v, Io=full load ±0.01 ±0.2 % Temperature regulation Vin=110V, Tc= min to max case temperatrue ±0.004 ±0.007 %/ 3.2 Output Voltage Ripple and Noise 5Hz to 20MHz bandwidth Peak-to-Peak Full Load, mv rms Full Load, mv 3.3 Operating Output Current Range A 3.4 Output DC Current-Limit Inception A 4.DYNAMIC CHARACTERISTICS 4.1 Output Voltage Current Transient 110V, 0.1A/µs Positive Step Change in Output Current 50% Io.max to 75% mv Negative Step Change in Output Current 75% Io.max to 50% mv 4.2 Turn-On Transient Start-Up Time, From On/Off Control ms Start-Up Time, From Input ms Rise time(vout from 10% to 90%) ms 4.3 Maximum output capacitor 680 µf 5. EFFICIENCY % Load Vin=110V 86 % % Load Vin=110V 86.1 % 6.ISOLATION CHARACTERISTICS 6.1 Input to Output 3000 Vrms 6.2 Input to base 1500 Vrms 6.3 Output to base 500 Vrms 6.4 Isolation Resistance 10 MΩ 7. FEATURE CHARACTERISTICS 7.1 Switching Frequency 300 khz 7.2 ON/OFF Control, Negative Remote On/Off logic Logic High (Module On) 3 5 V Logic Low (Module Off) 0 1 V 7.3 Output Voltage Trim Range % 7.4 Output Over-Voltage Protection Over full temp range; % of nominal Vout % 8 GENERAL SPECIFICATIONS 8.1 MTBF 1,302 hours 8.2 Weight With heat spreader 80 grams 8.3.Over-Temperature Shutdown ( NTC resistor ) Refer to Figure 18 for NTC resistor location 118 C (T A=25 C, Natural convection, Vin=110Vdc, nominal Vout unless otherwise noted; P2

3 ELECTRICAL CHARACTERISTICS CURVES ef f i ci ency % % % % % % % % % % 0. 00% Out put cur r ent ( A) 110V 53V 154V power l oss Out put cur r ent ( A) 53V 110V 154V Figure 1: Efficiency vs. load current for 66,110and 160 input voltage at 25 C. Figure 2: Power dissipation vs. load current for 36V, 48V, and 75V input voltage at 25 C. Figure 3: Turn-on transient at zero load current) (20ms/div). Top Trace: Vout; 5V/div; Bottom Trace: ON/OFF input: 2V/div. Figure 4: Turn-on transient at full load current (20ms/div). Top Trace: Vout: 5V/div; Bottom Trace: ON/OFF input: 2V/div. Figure 5: Turn-on transient at zero load current (10ms/div). Top Trace: Vout; 5V/div; Bottom Trace: input voltage: 50V/div. Figure 6: Turn-on transient at full load current (10ms/div). Top Trace: Vout; 1V/div; Bottom Trace: input voltage: 50V/div. P3

4 ELECTRICAL CHARACTERISTICS CURVES Figure 7: Output voltage response to step-change in load current (50%-75%-50% of full load; di/dt = 0.1A/µs). Bottom Trace: Vout;100mV/div; Time: 1ms/div Figure 8: Output voltage response to step-change in load current (50%-75%-50% of full load; di/dt = 2.5A/µs). Bottom Trace: Vout; 50mV/div; Time: 1ms/div Vo(+) scope r Resistor load Vo(-) Figure 9: Output voltage noise and ripple measurement test setu out put vol t age( V) OCL Out put cur r ent ( A) Figure 10: Output voltage ripple at nominal input voltage and max load current (10 mv/div, 2us/div) Bandwidth: 20 MHz. Figure 11: Output voltage vs. load current showing typical current limit curves and converter shutdown points. P4

5 DESIGN CONSIDERATIONS Input Source Impedance Test Result: At T = +25 C, Vin = 110V and full load blue line is peak mode; The impedance of the input source connecting to the DC/DC power modules will interact with the modules and affect the stability. A low ac-impedance input source is recommended. If the source inductance is more than a few μh, we advise 150μF electrolytic capacitor (ESR < 0.7 Ω at 100 khz) mounted close to the input of the module to improve the stability. dbμv Limits 55022MAV 55022MQP Layout and EMC Considerations 40.0 Transducer 8130 Delta s DC/DC power modules are designed to operate in a wide variety of systems and applications. For design assistance with EMC compliance and related PWB layout issues, please contact Delta s technical support team. Below is the reference design for an input filter tested with HA1SV12008PRFA to meet class A in CISSPR 22. Schematic and Components List C121=120Uf/400V Figure 12 EMC test schematic C123,C124,C127,C132 =220pF/275VAC C128,C129,C130,C131=2200pF/300VAC C122,C125,C126=0.47uF/250V T1=3.4mH, common choke R110,R111,R112,E113,R114=300kohm/ khz 1 MHz 10 MHz 30 MHz Safety Considerations Figure 13 EMI test positive line Traces PK+ AV The power module must be installed in compliance with the spacing and separation requirements of the end-user s safety agency standard, i.e., UL , CSA C22.2 NO nd and IEC nd : 2005 and EN nd: 2006+A11+A1: 2010, if the system in which the power module is to be used must meet safety agency requirements. Basic insulation based on 110 Vdc input is provided between the input and output of the module for the purpose of applying insulation requirements when the input to this DC-to-DC converter is identified as TNV-2 or SELV. An additional evaluation is needed if the source is other than TNV-2 or SELV. When the input source is SELV circuit, the power module meets SELV (safety extra-low voltage) requirements. If the input source is a hazardous voltage which is greater than 60 Vdc and less than or equal to 110 Vdc, for the module s output to meet SELV requirements, all of the following must be met: The input source must be insulated from the ac mains by reinforced or double insulation. The input terminals of the module are not operator accessible. A SELV reliability test is conducted on the system where the module is used, in combination with the module, to ensure that under a single fault, hazardous voltage does not appear at the module s output. P5

6 When installed into a Class II equipment (without grounding), spacing consideration should be given to the end-use installation, as the spacing between the module and mounting surface have not been evaluated. The power module has extra-low voltage (ELV) outputs when all inputs are ELV. This power module is not internally fused. To achieve optimum safety and system protection, an input line fuse is highly recommended. The safety agencies require a normal-blow fuse with 10A maximum rating to be installed in the ungrounded lead. A lower rated fuse can be used based on the maximum inrush transient energy and maximum input current. Remote On/Off The remote on/off feature on the module can be either negative or positive logic. Negative logic turns the module on during a logic low and off during a logic high. Positive logic turns the modules on during a logic high and off during a logic low. Remote on/off can be controlled by an external switch between the on/off terminal and the Vi (-) terminal. The switch can be an open collector or open drain. For negative logic if the remote on/off feature is not used, please short the on/off pin to Vi (-). For positive logic if the remote on/off feature is not used, please leave the on/off pin to floating. Soldering and Cleaning Considerations Post solder cleaning is usually the final board assembly process before the board or system undergoes electrical testing. Inadequate cleaning and/or drying may lower the reliability of a power module and severely affect the finished circuit board assembly test. Adequate cleaning and/or drying is especially important for un-encapsulated and/or open frame type power modules. For assistance on appropriate soldering and cleaning procedures, please contact Delta s technical support team. FEATURES DESCRIPTIONS Over-Current Protection The modules include an internal output over-current protection circuit, which will endure current limiting for an unlimited duration during output overload. If the output current exceeds the OCP set point, the modules will shut down, and will try to restart after shutdown(hiccup mode). If the overload condition still exists, the module will shut down again. This restart trial will continue until the overload condition is corrected. Over-Voltage Protection The modules include an internal output over-voltage protection circuit, which monitors the voltage on the output terminals. If this voltage exceeds the over-voltage set point, the protection circuit will constrain the max duty cycle to limit the output voltage, if the output voltage continuously increases the modules will shut down, and then restart after a hiccup-time (hiccup mode). Over-Temperature Protection The over-temperature protection consists of circuitry that provides protection from thermal damage. If the module will shut down.the module will restart after the temperature is within specification. Figure 14: Remote on/off implementation Output Voltage Adjustment (TRIM) To increase or decrease the output voltage set point, connect an external resistor between the TRIM pin and SENSE(+) pin or SENSE(-) pin. The TRIM pin should be left open if this feature is not used. For trim down, the external resistor value required to obtain a percentage of output voltage change % is defined as: 10 * Vnom *(1 ) Rtrim down K Vnom Vnom *(1 ) Ex. When Trim-down -10% (12V 0.9=10.8V) 10 *12* 0.9 Rtrim down K 90 K 12 12* 0.9 For trim up, the external resistor value required to obtain a percentage output voltage change % is defined as: Vnom ( 1 ) 2.5 *120 Rtrim up 10 K Vnom 2.5 Ex. When Trim-up +10% (12V 1.1=13.2V) 12 (1 0.1) 2.5 *120 Rtrim up K The output voltage can be increased by both the remote sense and the trim, however the maximum increase is the larger of either the remote sense or the trim, not the sum of both. P6

7 The output voltage can be increased by both the remote sense and the trim, however the maximum increase is the larger of either the remote sense or the trim, not the sum of both. When using remote sense and trim, the output voltage of the module is usually increased, which increases the power output of the module with the same output current. Care should be taken to ensure that the maximum output power of the module remains at or below the maximum rated power. Pin function The pin was difine as follow in figure 20,we will explain the pin function: +IN, -IN. DC voltage inputs. Gate IN. The Gate IN pin on a driver module may be used as a logic enable/disable input.when Gate IN is pull low (<1V,referenced to Vin ),the module is turned off. when Gate IN is floating (open collector),the module is turned on.the open circuit voltage of Gate in PIN is less than 5V. Gate OUT. The pulsed signal at the Gate OUT pin of a regulating driver module is used to synchronously drive the surge circuit in order to meet the RIA12 surge needed. If you don t used this function, please floating it. +OUT, -OUT. DC voltage outputs. T(TRIM). Provides fixed or variable adjustment of the module output. Trimming down. Allows output voltage of the module to be trimmed down, with a decrease in efficiency.ripple as a percent of output voltage goes up and input range widens since input voltage dropout(loss of regulation) moves down Trimming up. Reverses the above effects. -Sense,+Sense. Provides for locating the point of optimal voltage regulation external to the converter. THERMAL CONSIDERATIONS Thermal management is an important part of the system design. To ensure proper, reliable operation, sufficient cooling of the power module is needed over the entire temperature range of the module. Convection cooling is usually the dominant mode of heat transfer. Hence, the choice of equipment to characterize the thermal performance of the power module is a wind tunnel. Thermal Testing Setup Delta s DC/DC power modules are characterized in heated vertical wind tunnels that simulate the thermal environments encountered in most electronics equipment. This type of equipment commonly uses vertically mounted circuit cards in cabinet racks in which the power modules are mounted. The following figure shows the wind tunnel characterization setup. The power module is mounted on a test PWB and is vertically positioned within the wind tunnel. The space between the neighboring PWB and the top of the power module is constantly kept at 6.35mm (0.25 ). FANCING PWB AIR VELOCITY AND AMBIENT TEMPERATURE SURED BELOW THE MODULE AIR FLOW PWB MODULE 50.8(2.00") Note: Wind Tunnel Test Setup Figure Dimensions are in millimeters and (Inches) Thermal Derating Figure 15: Wind tunnel test setup Heat can be removed by increasing airflow over the module. To enhance system reliability, the power module should always be operated below the maximum operating temperature. If the temperature exceeds the maximum module temperature, reliability of the unit may be affected. P7

8 THERMAL CURVES THERMAL CURVES Figure 16: * temperature measured point Figure 17: Output current vs. ambient temperature and air Orientation, airflow from input to output,with heat spreader) THERMAL CURVES Figure 18: NTC resistor location P8

9 LEAD FREE (SAC) PROCESS RECOMMEND TEMP. PROFILE Figure 19 recommended temperature profile for lead-free wave soldering MECHANICAL DRAWING(BASEPLATE) Figure 20 the pin function and mechanical drawing P9

10 MECHANICAL DRAWING(WITHOUT MOUNTING HOLE) Figure 20 the pin function and mechanical drawing DIMENSIONAL TOLERANCE X ±0.3mm x.x ±0.2mm x.xx ±0.1mm P10

11 PART NUMBERING SYSTEM H A1 S V N N F A Form Input Number of Product Output Output ON/OFF Pin Option Code Factor Voltage Outputs Series Voltage Current Logic Length H - Half Brick V~154V S Single V- Series 12-12V A N Negative N R M - SMD pin F - RoHS 6/6 (Lead Free) A Baseplate H without mounting hole Number P - Space - RoHS5/6 Positive MODEL LIST MODEL NAME INPUT OUTPUT 100% LOAD HA1SV12008PRFA 53V~154V 2.2A 12V 8.3A 86% HA1SV12008PRFH 53V~154V 2.2A 12V 8.3A 86% Default remote on/off logic is negative and pin length is For different remote on/off logic and pin length, please refer to part numbering system above or contact your local sales office. For modules with through-hole pins and the optional heatspreader, they are intended for wave soldering assembly onto system boards; please do not subject such modules through reflow temperature profile. CONTACT: USA: Telephone: East Coast: West Coast: Fax: (978) dcdc@deltaww.com Europe: Phone: Fax: Asia & the rest of world: Telephone: ext 6220~6224 Fax: WARRANTY Delta offers a five (5) year limited warranty. Complete warranty information is listed on our web site or is available upon request from Delta. Information furnished by Delta is believed to be accurate and reliable. However, no responsibility is assumed by Delta for its use, nor for any infringements of patents or other rights of third parties, which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Delta. Delta reserves the right to revise these specifications at any time, without notice. P11