Product Specification RoHS-6 Compliant 10Gb/s 850nm Multimode X2 Transponder FTLX8541E2/FTLX8541F2

Transcription

1 Product Specification RoHS-6 Compliant 10Gb/s 850nm Multimode X2 Transponder FTLX8541E2/FTLX8541F2 PRDUCT FEATURES Hot pluggable X2 MSA form factor Total power consumption: 2.2 W maximum RoHS-6 compliant (lead-free) Temperature range 0 C to 70 C Transmission distance of 300m Uncooled 850 nm VCSEL laser SC connector, multimode fiber Full duplex transmission mode Digital ptics Monitoring (DM) Power supply: +5.0 V, +3.3 V Adaptable Power Supply (APS: +1.2 V) XAU electrical interface 4x Gb/s Ethernet (FTLX8541E2) 4x Gb/s Fibre Channel (FTLX8541F2) Management and control via MD 2-wire bus 70-pin connector Separated signal/chassis ground Mid Pak module variance for front panel mounting De-latch mechanism with low extraction force APPLCATNS 10GBASE-SR 10G Ethernet (FTLX8541E2) 1200-Mx-SN- 10G Fibre Channel: (FTLX8541F2) PRDUCT SELECTN Part Number Applications FTLX8541E2 10G Ethernet FTLX8541F2 10G Fibre Channel Finisar Corporation August 2015 Rev. C Page 1

2 . Pin Descriptions Signal Name Level / Pin No. Description Management and Monitoring Ports MD pen Drain / 17 Management Data /. Requires external kω pull-up to the APS on host. MDC 1.2 V 18 Management Data Clock nput CMS PRTAD4 1.2 V 1 19 Port Address nput bit 4 CMS PRTAD3 1.2 V 20 Port Address nput bit 3 CMS PRTAD2 1.2 V 21 Port Address nput bit 2 CMS PRTAD1 1.2 V 22 Port Address nput bit 1 CMS PRTAD0 1.2 V 23 Port Address nput bit 0 CMS LAS pen Drain 9 Link Alarm Status nterrupt utput. pen Drain Compatible utput with kω pull-up on host. Logic high = Normal peration Logic low = Status Flag Triggered RESET pen Drain 10 Reset nput. pen Drain Compatible nput with 22 kω pull-up to APS internal to transponder. Logic high = Normal peration Logic low = RESET Vendor Specific 11,15,16,24 Vendor Specific Pins. Leave unconnected when not used. TX N/FF pen Drain 12 TX N/FF nput. pen Drain Compatible nput with 22 kω pull-up to APS internal to transponder. Logic high = Transmitter n Logic low = Transmitter ff MD DETECT 14 Pulled low inside transponder through a 1 kω resistor to Ground Transmit Functions Reserved Reserved TX LANE 3 TX LANE 3+ TX LANE 2 TX LANE 2+ TX LANE 1 TX LANE 1+ TX LANE 0 TX LANE 0+ AC-coupled, nternally biased differential XAU Reserved For Future Use Reserved For Future Use Module XAU nput Lane 3 Module XAU nput Lane 3+ Module XAU nput Lane 2 Module XAU nput Lane 2+ Module XAU nput Lane 1 Module XAU nput Lane 1+ Module XAU nput Lane 0 Module XAU nput Lane 0+ Finisar Corporation August 2015 Rev. C Page 2

3 Receive Functions Reserved Reserved RX LANE 0+ RX LANE 0 AC-coupled, nternally biased differential XAU RX LANE 1+ RX LANE 1 RX LANE 2+ RX LANE 2 RX LANE 3+ RX LANE 3 DC Power GND 0 V DC 1, 2, 3, 33, 34, 35, 36, 37, 40, 43, 46, 49, 52, 53, 54, 57, 60, 63, 66, 69, 70 Reserved For Future Use Reserved For Future Use Module XAU utput Lane 0+ Module XAU utput Lane 0 Module XAU utput Lane 1+ Module XAU utput Lane 1 Module XAU utput Lane 2+ Module XAU utput Lane 2 Module XAU utput Lane 3+ Module XAU utput Lane 3 Ground connection for signal ground on the module APS +1.2 V 7, 8, 28, 29 nput from Adaptive Power Supply APS SENSE +1.2 V 27 APS Sense utput. Connected to the APS input inside transponder. APS SET 25 Feedback input from APS. Connected to GND through a 1180Ω resistor inside the transponder. 3.3 V +3.3 V DC 5, 6, 30, 31 DC Power nput, +3.3 V DC, Nominal 5.0 V +5.0 V DC 4, 32 DC Power nput, +5.0 V DC, Nominal Reserved 26 Reserved for APD. Reserved 13 Reserved. Finisar Corporation August 2015 Rev. C Page 3

4 Electrical Pad Layout Fig 1-X2 Transponder Electrical Pad Layout. Absolute Maximum Ratings Symbol Limit Values min. max. Storage Ambient Temperature 1) T S C perating Case Temperature 1) T C 0 70 C Supply Voltage +5.0 V V V Supply Voltage +3.3 V V V Supply Voltage APS V aps V Static Discharge Voltage, All Pins 2) ST d 500 V Average Receive ptical Power Rx P max 1.5 dbm Notes: 1) Non-condensing. 2) HBM. Exceeding any one of these values may permanently destroy the device. Unit Finisar Corporation August 2015 Rev. C Page 4

5 . Electrical Characteristics Recommended perating Conditions Values Symbol min. typ. max. Unit perating Case Temperature 1) T C 0 70 C Transponder Total Power P 2.2 W Consumption Supply Voltage +5.0 V V CC V Supply Current +5.0 V CC ma Supply Voltage +3.3 V V CC V Supply Current +3.3 V CC ma Supply Voltage APS V CC aps V Supply Current APS CC aps ma 1) Measured at reference thermal location, see Figure 2. See also Environmental Performance. Electrical DC Characteristics (V CC5 = 4.75 V to 5.25 V, V CC3 = 3.14 V to 3.47 V, V CC aps = V to V, T C = 0 C to 70 C) Values Symbol min. typ. max. Unit 1.2 V CMS (1.8 V CMS Compatible 1) ) / DC Characteristics (PRTAD; LAS; RESET; TX_NFF) External Pull-up Resistor for pen Drain R pullup kω utput High Voltage 2) V oh 1 V utput Low Voltage 2) V ol 0.15 V nput High Voltage V ih V nput Low Voltage V il 0.36 V nput Pull-down Current 3) pd µa XAU / DC Characteristics (TXLANE[0..3]; RXLANE[0..3]) Differential nput Amplitude (pk-pk) 4) V in xaui mv Differential utput Amplitude (pk-pk) 4) V out xaui mv MD / DC Characteristics (MD; MDC) utput Low Voltage 5) V L V utput Low Current L 20 ma nput High Voltage V H V nput Low Voltage V L V Pull-up Supply Voltage V PU V nput Capacitance C N 10 pf Load Capacitance C LAD 470 pf External Pull-up Resistance R LAD 200 Ω 1) For 1.8 V CMS V oh = 1.65 V min., V ol = 0.15 V max., V ih = 1.17 V min., V il = 0.63 V max. 2) R pull-up = 10 kω to 1.8 V. 3) V in = 1.8 V. 4) AC coupled. 5) L = 100 µa. Finisar Corporation August 2015 Rev. C Page 5

6 Electrical AC Characteristics (V CC5 = 4.75 V to 5.25 V, V CC3 = 3.14 V to 3.47 V, V CC aps = V to V, T C = 0 C to 70 C) Values Symbol min. typ. max. Unit XAU nput AC Characteristics (TXLANE[0..3]) Baud Rate R XAUN Gbit/s Fibre Channel Ethernet Baud Rate Tolerance R TLXAU ppm Differential nput mpedance Z NXAU Ω Differential Return Loss 1) S db nput Differential Skew 2) t SKEWN 75 ps Jitter Amplitude Tolerance 3) J XAUTL 0.65 U p-p XAU utput AC Characteristics (RXLANE[0..3]) Baud Rate R XAUUT Gbit/s Fibre Channel Ethernet Baud Rate Variation R XAUVAR ppm XAU Eye Mask (far-end) According to EEE 802.3ae and 10G Fibre Channel utput Differential Skew t SKEWUT 15 ps utput Differential mpedance Z UTXAU Ω Differential utput Return Loss 1) S db Total Jitter 4) TJ XAU 0.35 U Deterministic Jitter 4) DJ XAU 0.37 U Power-n Reset AC Characteristics Power-n Reset and TX_NFF According to XENPAK MSA ssue 3.0, Characteristics MD / AC Characteristics (MD; MDC) MD Data Hold Time t HLD 10 ns MD Data Setup Time t SU 10 ns Delay from MDC Rising Edge to t DELAY 300 ns MD Data Change MDC Clock Rate ƒ MAX 2.5 MHz 1) 100 MHz to 2.5 GHz. 2) At crossing point. 3) Per EEE Std 802.3ae. 4) At near-end, No pre-equalization, 1 U = 320 ps. Finisar Corporation August 2015 Rev. C Page 6

7 V. ptical Characteristics (V CC5 = 4.75 V to 5.25 V, V CC3 = 3.14 V to 3.47 V, V CC aps = V to V, T C = 0 C to 70 C, BER 1E-12, Bit Rate ) Values Symbol min. typ. max. Unit Transmitter Launch Power in MA 1) P -MA dbm Average Launch Power P -Avg 5 1 dbm TDP TDP 3.9 db Center Wavelength Range 1) λ C-Tx nm RMS Spectral Width 1) σ nm Extinction Ratio ER db Relative ntensity Noise 12 MA RN 128 db/hz Eye Mask Definition According to EEE and Fibre Channel Encircled Flux EF at 19 µm 86%, at 4.5 µm 30% ptical Return Loss Tolerance RL T 12 db Average Launch Power of FF P -FF 30 dbm Transmitter Receiver Stressed Receiver Sensitivity in MA P N-S 7.5 dbm Receiver Sensitivity in MA 2) P N 11.1 dbm Average Receive Power P N-max -1 dbm Signal Detect Deassert Level P SDL 14.5 dbm Signal Detect Assert Level P SD 18.0 dbm Signal Detect Hysteresis P SD db Receiver Reflectance REF RX 12 db Center Wavelength Range λ C-RX nm 1) Conforms to EEE triple trade-off between center wavelength, RMS spectral width and minimum MA. 2) Receiver sensitivity, which is defined for an ideal input signal is informative only. V. General Specifications ptical nterface Standard Specifications Standard Fiber Type Minimum Modal Bandwidth at 850 nm (MHz*km) perating Range 1) (meters) EEE 62.5 µm MMF to µm MMF to 66 Fibre 62.5 µm MMF to 33 Channel 50 µm MMF to µm MMF to 300 Notes: 1) perating range as defined by EEE and Fibre Channel standards. Longer reach possible depending upon link implementation. Finisar Corporation August 2015 Rev. C Page 7

8 Environmental Performance perating case temperature: perating humidity: 0 C to +70 C 0% -95% RH non-condensing Fibers and Connectors The transponder has SC receptacles for both Tx and Rx. The transponder is designed for multimode SC cables, 0 polished endface (PC). 70-pin Connector The module interface connector is a 70-pin, printed circuit board edge connection with a 0.5 mm pitch. The appropriate mating connector for the customer PCB is a 70-pin SMT, dual row, right angled, edge connector, 0.5 mm pitch (Tyco Electronics part number , Molex part number or equivalent). Rail and Mechanical Mounting Requirements The X2 rail system required to mount the X2 module is fully defined by the MSA. (Tyco Electronics part number : designed for belly to belly applications; and , designed for single sided board mount to fit into the standard host PCB footprint; or equivalent). For further details please refer to vendor-supplied information. Aqueous Wash Finisar X2 transponders are neither solderable nor aqueous washable and are not intended for these processes. V. Regulatory Compliance Feature Standard Comments ESD: Electrostatic Discharge to the Electrical Pins (HBM) EA/JESD22-A114-B (ML-STD 883D Method ) Class 1a (> 500 V) mmunity: Against Electrostatic Discharge (ESD) to the Module Receptacle mmunity: Against Radio Frequency Electromagnetic Field Emission: Electromagnetic nterference (EM) EN EC EN EC FCC 47 CFR Part 15, Class B EN Class B CSPR 22 Discharges ranging from ±2 kv to ±25 kv to the front end / faceplate / receptacle cause no damage to module (under recommended conditions). With a field strength of 10 V/m, noise frequency ranges from 10 MHz to 2 GHz. No effect on module performance between the specification limits. Noise frequency range: 30 MHz to 40 GHz Radiated emission does not exceed specified limits when measured with module inside a shielding enclosure with a MSA conforming cutout. Finisar Corporation August 2015 Rev. C Page 8

9 Eye Safety Finisar FTLX8541 transponders are Class 1 Laser Products. They are certified per the following standards: Feature Agency Standard Certificate Number Laser Eye FDA/CDRH CDRH 21 CFR 1040 and Laser Notice Safety Laser Eye TÜV EN : 1994+A11:1996+A2:2001 R Safety EC : 1993+A1:1997+A2:2001 EC : 2000, Edition 2 Electrical TÜV EN R Safety Electrical Safety UL/CSA CLASS CLASS Copies of the referenced certificates will be available at Finisar Corporation upon request. V. DM s Values min. typ. max. Unit Transponder Temperature Monitor Accuracy 1) C Laser Bias Current Monitor Accuracy 2) % Transmit Power Monitor Accuracy 3) db Receive Power Monitor Accuracy 3) db 1) 0 to 70 C case temperature. 2) 0 to 12.5 ma. 3) -8.2 dbm to +0.5 dbm. V. Mechanical Specifications Symbol Values Unit min. typ. max. Module Retention Force (latch strength) F RET 200 N Module nsertion Force F N 40 N Module Extraction Force (with kick-out) F EXT-K 16 N Module Extraction Force (without kick-out) F EXT 25 N Pull Sleeve front face color is beige. Finisar Corporation August 2015 Rev. C Page 9

10 Package utline Figure 2 - X2 Mechanical Dimensions X. References ptical nterface Standard Specifications References EEE Std 802.3ae-2002 clause 52, 10GBASE-SR Fibre Channel 10GFC Draft 4.0, 1200-M5-SN- Fibre Channel 10GFC Draft 4.0, 1200-M5E-SN- Fibre Channel 10GFC Draft 4.0, 1200-M6-SN- X2 MSA ssue 2.0b Electrical nterface Standard Specifications References EEE Std 802.3ae-2002 clause 45 & 47 X2 MSA ssue 2.0b X. For More nformation Finisar Corporation 1389 Moffett Park Drive Sunnyvale, CA Tel Fax sales@finisar.com Finisar Corporation August 2015 Rev. C Page 10