TEST REPORT. No. I18D00191-EMC01. For. Client : Shanghai Sunmi Technology Co.,Ltd. L1320/L1322 SUNMI 2AH25T2MINI

Transcription

1 TEST REPORT No. I18D00191-EMC01 For Client : Shanghai Sunmi Technology Co.,Ltd. Production: POS System Model Name : Brand Name: FCC ID: L1320/L1322 SUNMI 2AH25T2MINI Hardware Version: V1.03 Software Version: MST2MINI_EQ000_2EE0.123BBE _180824_100_V01_T15 Issued date: Note: The test results in this test report relate only to the devices specified in this report. This report shall not be reproduced except in full without the written approval of ECIT Shanghai. Test Laboratory: ECIT Shanghai, East China Institute of Telecommunications

2 Add: 7F, G Area, No.668, Beijing East Road, Huangpu District, Shanghai, P. R. China Tel: (+86) , welcome@ecit.org.cn Revision Version Report Number Revision Date Memo I18D00191-EMC Initial creation of test report East China Institute of Telecommunications Page Number : 2 of 22

3 CONTENTS 1. TEST LABORATORY TESTING LOCATION TESTING ENVIRONMENT PROJECT DATA SIGNATURE CLIENT INFORMATION APPLICANT INFORMATION MANUFACTURER INFORMATION EQUIPMENT UNDER TEST (EUT) AND ANCILLARY EQUIPMENT (AE) ABOUT EUT INTERNAL IDENTIFICATION OF EUT USED DURING THE TEST INTERNAL IDENTIFICATION OF AE USED DURING THE TEST REFERENCE DOCUMENTS REFERENCE DOCUMENTS FOR TESTING TEST RESULTS SUMMARY OF TEST RESULTS STATEMENTS TEST EQUIPMENTS UTILIZED RADIATED EMISSION EQUIPMENTS LIST AC CONDUCTED EMISSION EQUIPMENTS LIST SYSTEM CONFIGURATION DURING TEST TEST MODE CONNECTION DIAGRAM OF TEST SYSTEM MEASUREMENT RESULTS RADIATED EMISSION 30MHZ-18GHZ East China Institute of Telecommunications Page Number : 3 of 22

4 8.2 AC CONDUCTED EMISSION East China Institute of Telecommunications Page Number : 4 of 22

5 1. Test Laboratory 1.1. Testing Location Company Name: Address: ECIT Shanghai, East China Institute of Telecommunications 7F, G Area, No. 668, Beijing East Road, Huangpu District, Shanghai, P. R. China Postal Code: Telephone: Fax: FCC registration No: 1.2. Testing Environment Normal Temperature: Relative Humidity: 1.3. Project data Project Leader: 30-60%RH Zhou Yan Testing Start Date: Testing End Date: Signature Qin Yabin (Prepared this test report) You Jinjun (Reviewed this test report) Zheng Zhongbin (Approved this test report) East China Institute of Telecommunications Page Number : 5 of 22

6 2. Client Information 2.1. Applicant Information Company Name: Address : Telephone: Postcode: Manufacturer Information Company Name: Address : Shanghai Sunmi Technology Co.,Ltd. Room 505, KIC Plaza, No.388 Song Hu Road, Yang Pu District, Shanghai, China Shanghai Sunmi Technology Co.,Ltd. Room 505, KIC Plaza, No.388 Song Hu Road, Yang Pu District, Shanghai, China Telephone: Postcode: East China Institute of Telecommunications Page Number : 6 of 22

7 3. Equipment under Test (EUT) and Ancillary Equipment (AE) 3.1. About EUT ProductName POS System Model name L1320/L1322 GSM Frequency Band GSM850/GSM1900 UMTS Frequency Band WCDMA BandⅡ/Ⅴ CDMA Frequency Band BC0 LTE Frequency Band LTE 38/41 Additional Communication Function BT4.0,BLE;WIFI b,g,n; 3.2. Internal Identification of EUT used during the test EUT ID* SN or IMEI HW Version SW Version Date of receipt N02(L1320) / V1.03 N01(L1322) / V1.03 MST2MINI_EQ000_2EE0.123BB E _180824_100_V01_T 15 MST2MINI_EQ000_2EE0.123BB E _180824_100_V01_T *EUT ID: is used to identify the test sample in the lab internally Internal Identification of AE used during the test AE ID* Description Model SN CA04 Adapter TPA UU / UA01 AC Cable / / EA02 IOIOI Cable / / AE1 USB Cable / / AE2 LAN Cable / / AE3 Cash Box / / AE4 Keyboard / / AE5 Mouse / / AE6 Notebook PC DELL Latitude E6510 / AE7 SanDisk Ultra32GB MicroSDHC UHS-I / AE8 U disk DT101 G2 / AE9 Earphone / / AE10 USB Cable / / *AE ID: is used to identify the test sample in the lab internally. East China Institute of Telecommunications Page Number : 7 of 22

8 4. Reference Documents 4.1. Reference Documents for testing The following documents listed in this section are referred for testing. Reference Title Version FCC Part 15, Subpart B ANSI C63.4 Radio frequency devices Method of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and Electronic Equipment in the Range of 9 khz to 40 GHz Edition 2014 East China Institute of Telecommunications Page Number : 8 of 22

9 5. Test Results 5.1. Summary of Test Results Items Test List Clause in FCC rules Verdict 1 Radiated Emission (a) Pass 2 AC Conducted Emission (a) Pass 5.2. Statements TheL1320/L1322, supporting GSM/WCDMA/CDMA/LTE/BT/WLAN.etc, manufactured by Shanghai Sunmi Technology Co.,Ltd. is a variant product for testing. ECIT only performed test cases which identified with Pass/Fail/Inc result in section 5.1. ECIT has verified that the compliance of the tested device specified in section 3 of this test report is successfully evaluated according to the procedure and test methods as defined in type certification requirement listed in section 4 of this test report. Note: This project on the basis of the I18D00189-EMC01 original report. Test content for the original report of the worst mode, embodied in the report data is the worst mode. Other information reference original report. East China Institute of Telecommunications Page Number : 9 of 22

10 6. Test Equipments Utilized 6.1 Radiated Emission Equipments list No. Name Type Series Cal. Producer Cal. Date Number interval 1 Universal Radio Communication CMU R&S Year 2 Test Receiver ESU R&S Year 3 Trilog Antenna VULB9163 VULB Schwarzbeck Year 4 5 Double Ridged Guide EMI Test Software ETS ETS Year EMC32 V9.15 NA R&S NA NA 6.2 AC Conducted Emission Equipments list No. Name Type Series Number Producer Cal. Date Cal. interval 1 Universal Radio CMU R&S Year 2 Test Receiver ESCI R&S Year Line V-Network EMI Test Software ENV R&S Year EMC32 V NA R&S NA NA East China Institute of Telecommunications Page Number : 10 of 22

11 7. System Configuration during Test 7.1 Test Mode N02 Sample (L1320) Test Item AC Conducted Emission Mode 2: Data link mode<figure 2> Function Type Radiated Emission Mode 1: Working mode _Full system <Figure 1> Mode 2: Data link mode<figure 2> Remark: 1. All test modes are performed, only the worst cases test data are recorded in this report. 2. Data Link with PC means data application transferred mode between EUT and PC. N01 Sample (L1322) Test Item AC Conducted Emission Mode 2: Data link mode<figure 2> Function Type Radiated Emission Mode 1: Working mode _Full system <Figure 1> Mode 2: Data link mode<figure 2> Remark: 3. All test modes are performed, only the worst cases test data are recorded in this report. 4. Data Link with PC means data application transferred mode between EUT and PC. Note: The full system include LAN cable, cash box, keyboard, mouse, earphone, printer, U disk, POS and notebook PC. East China Institute of Telecommunications Page Number : 11 of 22

12 7.2 Connection Diagram of Test System IOIOI Cable LAN Cable USB Cable Cash Box Note PC EUT Adapter Keyboard Mouse U Disk <Figure 1>Mode 1 USB Cable Note PC EUT Adapter <Figure 2>Mode 2 East China Institute of Telecommunications Page Number : 12 of 22

13 8. Measurement Results Only the worst test result was shown in this report. 8.1 Radiated Emission 30MHz-18GHz Method of Measurement For 30MHz -1000MHz, the EUT was placed on the top of a rotating 0.8-m table above the ground at a semi-anechoic chamber. The distance between the EUT and the received antenna was 3 meters. The table was rotated 360 degree and the received antenna mounted on a variable-height antenna tower was varied from 1m to 4m to find the maximum value of the field strength. Both horizontal and vertical polarizations of the antenna were set during the measurement. Tested in accordance with the procedures of ANSI C , section 8.3. For 1000MHz MHz,The maximal emission value was acquired by adjusting the antenna height, The table was rotated 360 degree to determine the maximum value of the field strength. Both horizontal and vertical polarizations of the antenna were set during the measurement. Limits for Radiated Emission at a measuring distance of 3m Frequency Range (MHz) Quasi-Peak ) Above Frequency Range (MHz) Peak ) Average ) Above Test conditions Frequency Range (MHz) RBW/VBW Sweep Time (s) kHz/300kHz Auto MHz/3MHz Auto Uncertainty Measurement The measurement uncertainty is 4.98dB (30MHz -1000MHz) and 5.06dB(1GHz -18GHz)(k=2) East China Institute of Telecommunications Page Number : 13 of 22

14 Test Results N02 Sample Mode 2: Data link mode<figure 2> Frequency Range: 30MHz 1GHz Frequency QuasiPeak Limit Margin Meas. Bandw idth Height Pol Azimuth Corr. (MHz) (dbµv/m) (dbµv/m) Time (khz) (cm) (deg) (ms) V H H H H H Note: 1. Emission level(qp)=raw value by receiver + Corr(Antenna factor + cable loss - preamplifier gain) 2. The raw value is used to calculate by software which is not shown in the sheet. 3. Margin=limit value emission level. East China Institute of Telecommunications Page Number : 14 of 22

15 N01 Sample Mode 2: Data link mode<figure 2> Frequency Range: 30MHz 1GHz Frequency QuasiPeak Limit Margin Meas. Bandw idth Height Pol Azimut Corr. (MHz) (dbµv/m) (dbµv/m) Time (khz) (cm) h (ms) (deg) V V H H V V Note: 1. Emission level(qp)=raw value by receiver + Corr(Antenna factor + cable loss - preamplifier gain) 2. The raw value is used to calculate by software which is not shown in the sheet. 3. Margin=limit value emission level. East China Institute of Telecommunications Page Number : 15 of 22

16 N02 Sample Mode 1: Working mode _Full system <Figure 1> Frequency Range: 1GHz 18GHz, Horizontal Final Result Frequency MaxPeak Average Limit Margi Meas. Bandw idt Heigh Po Azim Corr. (MHz) n H H H H H H H H H H H H Note: 1. Emission level(peak or average)=raw value by receiver + Corr(Antenna factor+ cable loss - preamplifier gain) 2. The raw value is used to calculate by software which is not shown in the sheet. 3. Margin=limit value emission level. Time h t l uth East China Institute of Telecommunications Page Number : 16 of 22

17 Frequency Range: 1GHz 18GHz, Vertical Final Result Frequency MaxPeak Average Limit Margin Meas. Bandw idt Heigh Po Azim Corr. (MHz) V V V V V V V V V V V V Note: 1. Emission level(peak or average)=raw value by receiver + Corr(Antenna factor+ cable loss - preamplifier gain) 2. The raw value is used to calculate by software which is not shown in the sheet. 3. Margin=limit value emission level. Time h t l uth East China Institute of Telecommunications Page Number : 17 of 22

18 N01 Sample Mode 1: Working mode _Full system <Figure 1> Frequency Range: 1GHz 18GHz, Horizontal Final Result Frequency MaxPeak Average Limit Margin Meas. Bandw idt Heigh Po Azim Corr. (MHz) H H H H H H H H H H H H Note: 1. Emission level(peak or average)=raw value by receiver + Corr(Antenna factor+ cable loss - preamplifier gain) 2. The raw value is used to calculate by software which is not shown in the sheet. 3. Margin=limit value emission level. Time h t l uth East China Institute of Telecommunications Page Number : 18 of 22

19 Frequency Range: 1GHz 18GHz, Vertical Final Result Frequency MaxPeak Average Limit Margin Meas. Bandw idt Heigh Po Azim Corr. (MHz) V V V V V V V V V V V V Note: 1. Emission level(peak or average)=raw value by receiver + Corr(Antenna factor+ cable loss - preamplifier gain) 2. The raw value is used to calculate by software which is not shown in the sheet. 3. Margin=limit value emission level. Time h t l uth East China Institute of Telecommunications Page Number : 19 of 22

20 8.2 AC Conducted Emission Method of Measurement For equipment that is designed to be connected to the public utility (AC) power line, the radio frequency voltage that is conducted back onto the AC power line on any frequency or frequencies with the band 150 khz to 30MHz shall not exceed the limits. Both lines of the power mains connected to the EUT were checked for maximum conducted interference. Tested in accordance with the procedures of ANSI C , section 7.3 Limit of AC Conducted Emission Frequency Range (MHz) Conducted Limit (dbuv) Quasi-peak Average to 56* 56 to 46* *Decreases with the logarithm of the frequency Test Condition in Charging Mode Voltage (V) Frequency (Hz) RBW Sweep Time (s) khz Auto Uncertainty Measurement The measurement uncertainty is 3.66dB (k=2). Test Results N02 Sample Mode 2: Data link mode<figure 2> East China Institute of Telecommunications Page Number : 20 of 22

21 Frequency Range: 150kHz 30MHz Frequency QuasiPeak Average Limit Margin Meas. Bandw idth Line Filter Corr. Note: (MHz) (dbμ V) (dbμ V) (dbμ V) N ON N ON N ON N ON N ON N ON L1 ON L1 ON N ON N ON L1 ON L1 ON Emission level(quasi-peak or Average peak)=raw value by receiver + Corr(Insertion loss+ cable loss) Time (khz) 2. The raw value is used to calculate by software which is not shown in the sheet. 3. Margin=limit value emission level. 4. L1 and N line is all have been tested, the result of them is synthesized in the above data diagram. N01 Sample Mode 2: Data link mode<figure 2> East China Institute of Telecommunications Page Number : 21 of 22

22 Frequency Range: 150kHz 30MHz Frequency (MHz) QuasiPeak (dbμ V) Average (dbμ V) Limit (dbμ V) Margin Meas. Time Bandw idth (khz) Line Filter Corr N ON N ON N ON N ON L1 ON L1 ON L1 ON L1 ON L1 ON L1 ON N ON N ON 9.8 Note: 1. Emission level(quasi-peak or Average peak)=raw value by receiver + Corr(Insertion loss+ cable loss) 2. The raw value is used to calculate by software which is not shown in the sheet. 3. Margin=limit value emission level. 4. L1 and N line is all have been tested, the result of them is synthesized in the above data diagram. **********END OF REPORT********** East China Institute of Telecommunications Page Number : 22 of 22