FCC PART 15C TEST REPORT FOR CERTIFICATION On Behalf of. Razer Inc. Notebook RZ FCC ID: RWO-RZ090196

Transcription

1 FCC ID:RWO-RZ FCC PART 15C TEST REPORT FOR CERTIFICATION On Behalf of Razer Inc. Notebook RZ FCC ID: RWO-RZ Prepared for : Razer Inc rd Street, Suite 900, San Francisco, CA Prepared By : No. 6, Kefeng Road, Science & Technology Park, Nanshan District, Shenzhen, Guangdong, China Tel: (0755) Report Number ACS-F16152 Date of Test Jul.05~18, 2016 Date of Report Aug.11, 2016

2 FCC ID:RWO-RZ Description TABLE OF CONTENTS Page 1. SUMMARY OF STANDARDS AND RESULTS Description of Standards and Results GENERAL INFORMATION Description of Device (EUT) Test Information Tested Supporting System Details Block diagram of connection between the EUT and simulators Test Facility Measurement Uncertainty (95% confidence levels, k=2) POWER LINE CONDUCTED EMISSION TEST Test Equipments Block Diagram of Test Setup Power Line Conducted Emission Test Limits Configuration of EUT on Test Operating Condition of EUT Test Procedure Power Line Conducted Emission Test Results RADIATED EMISSION TEST Test Equipment Block Diagram of Test Setup Radiated Emission Limit EUT Configuration on Test Operating Condition of EUT Test Procedure Radiated Emission Test Results CONDUCTED SPURIOUS EMISSIONS Test Equipment Limit Test Procedure Test result BAND EDGE COMPLIANCE TEST Test Equipment Limit Test Produce Test Results dB & 99% Bandwidth Test Test Equipment Limit Test Procedure Test Results OUTPUT POWER TEST Test Equipment Limit (FCC Part 15C b(3)) Test Procedure Test Results POWER SPECTRAL DENSITY TEST Test Equipment

3 FCC ID:RWO-RZ Limit Test Procedure Test Results ANTENNA REQUIREMENT Standard Applicable Antenna Connected Construction DEVIATION TO TEST SPECIFICATIONS

4

5 FCC ID:RWO-RZ Page SUMMARY OF STANDARDS AND RESULTS 1.1. Description of Standards and Results The EUT has been tested according to the applicable standards as referenced below. EMISSION Description of Test Item Standard Results Power Line Conducted Emission FCC Part 15: PASS Radiated Emission FCC Part 15: PASS Band Edge Compliance FCC Part 15: PASS Conducted spurious emissions FCC Part 15: PASS 6dB Bandwidth FCC Part 15: PASS Peak Output Power FCC Part 15: PASS Power Spectral Density FCC Part 15: PASS Antenna requirement FCC Part 15: PASS N/A is an abbreviation for Not Applicable.

6 FCC ID:RWO-RZ Page GENERAL INFORMATION 2.1. Description of Device (EUT) Product : Notebook Model No. FCC ID : RZ : RWO-RZ Radio : IEEE a/b/g/n/ac; Bluetooth V3.0+EDR; Bluetooth V4.1 Operation Frequency Modulation Technology Antenna Assembly Gain : IEEE a: 5180MHz 5240MHz; 5260MHz 5320MHz 5500MHz 5700MHz; 5745MHz 5825MHz IEEE ac VHT20: 5180MHz 5240MHz; 5260MHz 5320MHz 5500MHz 5700MHz; 5745MHz 5825MHz IEEE ac VHT40: 5190MHz 5230MHz; 5270MHz 5310MHz 5510MHz 5670MHz; 5755MHz 5795MHz IEEE ac VHT80: 5210MHz, 5290MHz; 5530MHz; 5775MHz IEEE b: 2412MHz 2462MHz IEEE g: 2412MHz 2462MHz IEEE802.11nHT20: 2412MHz 2462MHz; 5180MHz 5240MHz; 5260MHz 5320MHz 5500MHz 5700MHz; 5745MHz 5825MHz IEEE802.11nHT40: 2422MHz 2452MHz; 5190MHz 5230MHz; 5270MHz 5310MHz 5510MHz 5670MHz; 5755MHz 5795MHz Bluetooth : MHz : IEEE b: DSSS(CCK,DQPSK,DBPSK) IEEE a/g: OFDM(64QAM, 16QAM, QPSK, BPSK) IEEE ac VHT20, VHT40, VHT80: OFDM(16QAM, 64QAM, 256QAM, QPSK, BPSK) IEEE n HT20, HT40: OFDM (64QAM, 16QAM,QPSK,BPSK) Bluetooth V3.0+EDR: GFSK, π/4dqpsk,8-dpsk Bluetooth V4.1:GFSK : Antenna Type: PIFA Bluetooth: 2.91dBi WIFI 2.4GHz:ANT 0: 2.91dBi; ANT 1: 2.95dBi WIFI 5GHz: Band 1: ANT 0: 2.51dBi; ANT 1: 2.73dBi Band 2: ANT 0: 2.82dBi; ANT 1: 2.72dBi Band 3: ANT 0: 3.90dBi; ANT 1: 3.91dBi Band 4: ANT 0: 3.82dBi; ANT 1: 2.76dBi

7 FCC ID:RWO-RZ Page 2-2 Applicant Manufacturer Factory Power Adapter : Razer Inc rd Street, Suite 900, San Francisco, CA : Razer Inc rd Street, Suite 900, San Francisco, CA : BYD Precision Manufacture Co., Ltd No.3001, Bao He Road, Baolong Industrial, Longgang Street, Longgang Zone, Shenzhen, , P.R., China : Manufacturer: Razer Inc. M/N: RC Input: Vac; 50/60Hz, 2.0A Output: 20V; 2.25A DC Cable: Shielded, Undetachable, 2.0m Date of Test : Jul.05~18, 2016 Date of Receipt : Jul.03, Test Information A special test software was used to control EUT work in Continuous TX mode(nearly 100% duty cycle), and select test channel, wireless mode and data rate. Tested mode, channel, and data rate information Mode data rate Channel Frequency (Mpbs)(see Note) (MHz) 1 Low :CH IEEE b 1 Middle: CH High: CH Low :CH IEEE g 6 Middle: CH High: CH MCS0 Low :CH IEEE n HT20 MCS0 Middle: CH MCS0 High: CH IEEE n HT40 MCS0 Low :CH MCS0 Middle: CH MCS0 High: CH Note: 1. According exploratory test, EUT will have maximum output power in those data rate, so those data rate were used for all test. Note: 2. 11b/g use SISO mode, choose ANT0 which has the worse case emission for the radiated emission and band edge measurement, 11n mode use MIMO Mode, test with two antenna transmit simultaneously in 11n mode, and comply with KDB662911D01 V02r01.

8 FCC ID:RWO-RZ Page Tested Supporting System Details No. Description ACS No. Manufacturer Model Serial Number 1. HDD#1 2. HDD#2 3. Headphone 4. Monitor ACS-EMC-HDD38 WD WD Elements WXA1E63CEME4 Data Cable: Shielded, Detachable, 1.0m ACS-EMC-HDD39 WD WD Elements WX61A Data Cable: Shielded, Detachable, 1.0m ACS-EMC-EP01 OVANN OV880V --- Data Cable: Shielded, Undetachable, 2.0m ACS-EMC-LM01R ViewSonic VLCDS W A210521A0131 Power Cord: Unshielded, Detachable, 1.8m 2.2. Block diagram of connection between the EUT and simulators HDD#1~#2 AC Mains Monitor EUT Headphone Adapter AC Mains (EUT: Notebook)

9 FCC ID:RWO-RZ Page Test Facility Site Description Name of Firm : 3m Anechoic Chamber : 3m & 10m Anechoic Chamber : EMC Lab. : : : No. 6, Ke Feng Rd., 52 Block, Shenzhen Science & Industrial Park,Nantou, Shenzhen, Guangdong, China Certificated by FCC, USA Registration Number: Valid Date: Jul.12, 2017 Certificated by FCC, USA Registration Number: Valid Date: Jul.12, 2017 Certificated by Industry Canada Registration Number: IC 5183A-1 Valid Date: May.14, 2017 Certificated by DAkkS, Germany Registration No: D-PL Valid Date: Dec.15, 2016 Accredited by NVLAP, USA NVLAP Code: Valid Date: Mar.31, Measurement Uncertainty (95% confidence levels, k=2) Test Item Uncertainty for Conduction emission test in No. 1 Conduction Uncertainty for Radiation Emission test in 3m chamber Uncertainty 3.2dB (150kHz to 30MHz) 2.8dB(30~200MHz, Polarization: H) 2.8dB(30~200MHz, Polarization: V) 2.8dB(200M~1GHz, Polarization: H) 2.8dB(200M~1GHz, Polarization: V) 5.8dB(1~6GHz, Distance: 3m) 5.8dB(6~18GHz, Distance: 3m) Uncertainty for Radiation Emission test in 3m chamber (1GHz-18GHz) Uncertainty for Radiated Spurious Emission test in RF chamber 3.6dB Uncertainty for Conduction Spurious emission test 2.0dB Uncertainty for Output power test 0.8dB Uncertainty for Bandwidth test 83kHz Uncertainty for DC power test 0.1 % Uncertainty for test site temperature and 0.6 humidity 3%

10 FCC ID:RWO-RZ Page POWER LINE CONDUCTED EMISSION TEST 3.1. Test Equipments Item Equipment Manufacturer Model No. Serial No. Last Cal. Cal. Interval 1. 1# Shielding Room AUDIX N/A N/A Apr.17,16 1 Year 2. Test Receiver Rohde & Schwarz ESCI Apr.24,16 1 Year 3. L.I.S.N.#1 Rohde & Schwarz ESH2-Z Oct.18,15 1 Year 4. L.I.S.N.#2 Kyoritsu K NW-403D Apr.24,16 1 Year 5. Terminator Hubersuhner 50Ω No.1 May Year 6. Terminator Hubersuhner 50Ω No.2 May Year 7. RF Cable MIYAZAKI 3D-2W No.1 Apr.24,16 1Year 8. Coaxial Switch Anritsu MP59B Apr.23,16 1 Year 9. Test Software AUDIX e a N/A N/A Note: N/A means Not applicable Block Diagram of Test Setup PC System Receiver EUT Peripheral 80cm 0.8m LISN#1 LISN#2 :50Ω Terminator 3.3. Power Line Conducted Emission Test Limits Maximum RF Line Voltage Frequency Quasi-Peak Level db(μv) Average Level db(μv) 150kHz ~ 500kHz 66 ~ 56* 56 ~ 46* 500kHz ~ 5MHz MHz ~ 30MHz Notes: 1. * Decreasing linearly with logarithm of frequency. 2. The lower limit shall apply at the transition frequencies.

11 FCC ID:RWO-RZ Page Configuration of EUT on Test The following equipment are installed on Power Line Conducted Emission Test to meet the commission requirement and operating regulations in a manner which tends to maximize its emission characteristics in a normal application Notebook (EUT) Model Number : RZ Serial Number : N/A Support Equipment: As Tested Supporting System Details, in Section Operating Condition of EUT Setup the EUT and simulator as shown as Section Turn on the power of all equipments PC run test software to control EUT work in Tx (WiFi 2.4GHz) mode Test Procedure The EUT was placed on a non-metallic table, 80cm above the ground plane. The EUT Power Via PC connected to the power mains through a line impedance stabilization network (L.I.S.N. 1#). This provides a 50 ohm coupling impedance for the EUT (Please refer the block diagram of the test setup and photographs). The AC line are checked to find out the maximum conducted emission. In order to find the maximum emission levels, the relative positions of equipment and all of the interface cables shall be changed according to ANSI C63.10: 2013 on Conducted Emission Test. The bandwidth of test receiver (R & S ESCI) is set at 9kHz. The frequency range from 150kHz to 30MHz is checked Power Line Conducted Emission Test Results PASS. (All emissions not reported below are too low against the prescribed limits.)

12 FCC ID:RWO-RZ Page 3-3

13 FCC ID: RWO-RZ page RADIATED EMISSION TEST 4.1. Test Equipment For frequency range 30MHz~1000MHz (In 3m Anechoic Chamber) Item Equipment Manufacturer Model No. Serial No. Last Cal. Cal. Interval 1. 3#Chamber AUDIX N/A N/A Mar.28,16 1 Year 2. EMI Spectrum Agilent E4407B MY Apr.24,16 1 Year 3. Test Receiver Rohde & Schwarz ESVS /011 Apr.24,16 1 Year 4. Amplifier HP 8447D 2648A04738 Apr.24,16 1 Year 5. Bi-log Antenna TESEQ CBL6111C 2598 Jun.03,16 1 Year 6. RF Cable MIYAZAKI CFD400-N W(3.5M) No.3 Apr.24,16 1 Year 7. RF Cable MIYAZAKI CFD400-L W(22M) No.7 Apr.24,16 1 Year 8. Coaxial Switch Anritsu MP59B Apr.23,16 1 Year 9. Test Software AUDIX e a(n) N/A N/A Note: N/A means Not applicable For frequency range 1GHz~40GHz (In 3m Anechoic Chamber) Item Equipment Manufacturer Model No. Serial No. Last Cal. Cal. Interval 1. Spectrum Analyzer Agilent E4446A US Apr.24,16 1 Year 2. Horn Antenna ETS Oct.15,15 1 Year 3. Amplifier Agilent 8449B 3008A02495 Apr.24,16 1 Year 4. RF Cable Hubersuhner SUCOFLEX /4 Apr.24,16 1 Year 5. Horn Antenna ETS Oct.15,15 1 Year 6. Test Software AUDIX e a(n) N/A N/A Note: N/A means Not applicable.

14 FCC ID: RWO-RZ page Block Diagram of Test Setup For frequency range 30MHz-1000MHz Semi-anechoic 3m Chamber ANTENNA ELEVATION VARIES FROM 1 TO 4 METERS 3m EUT 2.0m(L)*1.0m(W)*0.8m(H) TURN TABLE (FIBRE GLASS) 0.8m Combining Network AMP Spectrum AnalABSORBER Receiver PC System For frequency range 1GHz-25GHz Semi-anechoic 3m Chamber ANTENNA ELEVATION VARIES FROM 1 TO 4 METERS Remark: If necessary, The antenna rise and fall from 1 to 4 meters. 3m (Reference Point) EUT 1.0m(L)*1.0m(W)*1.5m(H) ABSORBER (30cm maximum) TURN TABLE (Styrene) 1.5m (30cm) AMP Spectrum Analyzer PC System

15 FCC ID: RWO-RZ page Radiated Emission Limit &209 limits FREQUENCY DISTANCE FIELD STRENGTHS LIMIT MHz Meters μv/m db(μv)/m 30 ~ ~ ~ ~ Above db(μv)/m (Peak) 54.0 db(μv)/m (Average) Remark (1) Emission level dbμv = 20 log Emission level μv/m (2) The smaller limit shall apply at the cross point between two frequency bands. (3) Distance is the distance in meters between the measuring instrument, antenna and the closest point of any part of the device or system Restricted bands of operation All the emissions appearing within restricted frequency bands shall not exceed the limits shown in , all the other emissions shall be at least 20dB below the fundamental emissions, or comply with limits EUT Configuration on Test The following equipment are installed on Power Line Conducted Emission Test to meet the commission requirement and operating regulations in a manner which tends to maximize its emission characteristics in a normal application Notebook (EUT) Model Number : RZ Serial Number : N/A Support Equipment: As Tested Supporting System Details, in Section 2.2.

16 FCC ID: RWO-RZ page Operating Condition of EUT Setup the EUT and simulator as shown as Section Turn on the power of all equipments Let EUT work in Tx(WiFi 2.4GHz) mode 4.6. Test Procedure EUT and its simulators are placed on a turn table, which is 0.8 meter high above ground for frequency 30MHz~1000MHz, 1.5 meter high above ground for frequency above 1GHz and put the absorbing with 2.4m(L)*2.4m(W)*0.3m(H) on the ground. The turn table can rotate 360 degrees to determine the position of the maximum emission level. Power on the EUT and let it working in test mode, then test it.eut is set 3 meters away from the receiving antenna, which is mounted on a antenna tower. The antenna can be moved up and down between 1 meter and 4 meters to find out the maximum emission level. Broadband antenna (calibrated bilog antenna) is used as receiving antenna for frequency 30MHz~1000MHz, and the Horm antenna is used as receiving antenna for frequency above 1GHz. Both horizontal and vertical polarization of the antenna are set on test. This test was performed with EUT in X, Y, Z position, and the worse case was found when EUT in X position as test photo indicated. The bandwidth of the EMI test receiver (R&S ESVS10) is set at 120kHz for frequency range from 30MHz to 1000 MHz. The bandwidth of the Spectrum s VBW is set at 3MHz and RBW is set at 1MHz for peak emissions measurement above 1GHz and 1MHz RBW, 10Hz VBW for average emissions measure above 1GHz The frequency range from 30MHz to 10 th harmonic (25GHz) are checked. and no any emissions were found from 18GHz to 25GHz, So the radiated emissions from 18GHz to 25GHz were not record Radiated Emission Test Results PASS. All the emissions from 30MHz to 25 GHz were comply with limits. Note: For emissions above 1GHz, if peak level comply with average limit, then the average level is deemed to comply with average limit.

17 FCC ID: RWO-RZ page 4-5 Duty cycle Note: The Duty Cycle is close to 100%.

18 FCC ID: RWO-RZ page 4-6 Frequency: 30MHz~1GHz

19 FCC ID: RWO-RZ page 4-7 Frequency: 1GHz~18GHz

20 FCC ID: RWO-RZ page 4-8

21 FCC ID: RWO-RZ page 4-9

22 FCC ID: RWO-RZ page 4-10

23 FCC ID: RWO-RZ page 4-11

24 FCC ID: RWO-RZ page 4-12

25 FCC ID: RWO-RZ page 4-13

26 FCC ID: RWO-RZ page 4-14

27 FCC ID: RWO-RZ page 4-15

28 FCC ID: RWO-RZ page 4-16

29 FCC ID: RWO-RZ page 4-17

30 FCC ID: RWO-RZ page 4-18

31 FCC ID: RWO-RZ page 4-19

32 FCC ID: RWO-RZ page 4-20

33 FCC ID: RWO-RZ page 4-21

34 FCC ID: RWO-RZ page 4-22

35 FCC ID: RWO-RZ page 4-23

36 FCC ID: RWO-RZ page 4-24

37 FCC ID: RWO-RZ page CONDUCTED SPURIOUS EMISSIONS 5.1. Test Equipment Item Equipment Manufacturer Model No. Serial No. Last Cal. Cal. Interval 1. Spectrum Agilent N9030A MY Oct.17,15 1Year 2. Attenuator (20dB) 3. RF Cable 5.2. Limit Agilent 8491B MY Apr.23,16 1 Year Marvelous Microwave Inc SFL402105FLEX NO.1 Oct.17,15 1 Year In any 100kHz bandwidth outside the frequency bands in which the spread spectrum intentional radiator in operating, the radio frequency power that is produced by the intentional radiator shall be at least 20dB below that in the 100kHz bandwidth within the band that contains the highest level of the desired power Test Procedure The transmitter output was connected to a spectrum analyzer, The resolution bandwidth is set to 100 khz, The video bandwidth is set to 300 khz and measure all the emissions with peak detector Test result PASS (The testing data was attached in the next pages.)

38 FCC ID: RWO-RZ page 5-2 ANT0: Test Mode: IEEE b Test CH1: 2412MHz Test CH6: 2437MHz

39 FCC ID: RWO-RZ page 5-3 Test CH11: 2462MHz Test Mode: IEEE g Test CH1: 2412MHz

40 FCC ID: RWO-RZ page 5-4 Test CH6: 2437MHz

41 FCC ID: RWO-RZ page 5-5 Test CH11: 2462MHz Test Mode: IEEE n HT20 Test CH1: 2412MHz

42 FCC ID: RWO-RZ page 5-6 Test CH6: 2437MHz Test CH11: 2462MHz

43 FCC ID: RWO-RZ page 5-7 Test Mode: IEEE n HT40 Test CH3: 2422MHz

44 FCC ID: RWO-RZ page 5-8 Test CH6: 2437MHz Test CH9: 2452MHz

45 FCC ID: RWO-RZ page 5-9

46 FCC ID: RWO-RZ page 5-10 ANT1: Test Mode: IEEE b Test CH1: 2412MHz Test CH6: 2437MHz

47 FCC ID: RWO-RZ page 5-11 Test CH11: 2462MHz Test Mode: IEEE g Test CH1: 2412MHz

48 FCC ID: RWO-RZ page 5-12 Test CH6: 2437MHz

49 FCC ID: RWO-RZ page 5-13 Test CH11: 2462MHz Test Mode: IEEE n HT20 Test CH1: 2412MHz

50 FCC ID: RWO-RZ page 5-14 Test CH6: 2437MHz Test CH11: 2462MHz

51 FCC ID: RWO-RZ page 5-15 Test Mode: IEEE n HT40 Test CH3: 2422MHz

52 FCC ID: RWO-RZ page 5-16 Test CH6: 2437MHz Test CH9: 2452MHz

53 FCC ID: RWO-RZ page 5-17

54 FCC ID: RWO-RZ page BAND EDGE COMPLIANCE TEST 6.1. Test Equipment Item Equipment Manufacturer Model No. Serial No. Last Cal. Cal. Interval 1. Spectrum Agilent E4446A US Apr.24,16 1 Year 2. Amp HP 8449B 3008A02495 Apr.24,16 1 Year 3. Horn Antenna ETS Oct.15,15 1 Year 4. HF Cable Hubersuhner Sucoflex /4 Apr.24,16 1 Year 6.2. Limit All the lower and upper band-edges emissions appearing within 2310MHz to 2390MHz and MHz to 2500MHz restricted frequency bands shall not exceed the limits shown in , all the other emissions outside operation frequency band 2400MHz to MHz shall be at least 20dB below the fundamental emissions, or comply with limits Test Produce 1. The EUT is placed on a turntable, which is 1.5m above the ground plane and worked at highest radiated power. 2. The turntable was rotated for 360 degrees to determine the position of maximum emission level. 3. EUT is set 3m away from the receiving antenna, which is varied from 1m to 4m to find out the highest emission. 4. Set the spectrum analyzer in the following setting in order to capture the lower and upper band-edges of the emission: (a) PEAK: RBW=1MHz; VBW=3MHz; Sweep=AUTO (b) AVERAGE: RBW=1MHz; VBW=10Hz; Sweep=AUTO 6.4. Test Results Pass (The testing data was attached in the next pages.)

55 FCC ID: RWO-RZ page 6-2

56 FCC ID: RWO-RZ page 6-3

57 FCC ID: RWO-RZ page 6-4

58 FCC ID: RWO-RZ page 6-5

59 FCC ID: RWO-RZ page 6-6

60 FCC ID: RWO-RZ page 6-7

61 FCC ID: RWO-RZ page 6-8

62 FCC ID: RWO-RZ page 6-9

63 FCC ID: RWO-RZ page dB & 99% Bandwidth Test 7.1. Test Equipment Item Equipment Manufacturer Model No. Serial No. Last Cal. Cal. Interval 1. Spectrum Agilent N9030A MY Oct.18,15 1Year 2. Attenuator (20dB) Agilent 8491B MY Apr.23,16 1 Year Marvelous 3. RF Cable SFL402105FLEX NO.1 Oct Year Microwave Inc 7.2. Limit For direct sequence systems, the minimum 6dB bandwidth shall be at least 500kHz 7.3. Test Procedure The transmitter output was connected to a spectrum analyzer, The bandwidth of the fundamental frequency was measured by spectrum analyzer with 100kHz RBW and 300kHz VBW. The 6dB bandwidth is defined as the total spectrum the power of which is higher than peak power minus 6dB Test Results EUT: Notebook M/N: RZ Test date: Pressure: kpa Humidity: % Tested by: Alice-Yang Test site: RF site Temperature: Test Mode 11b 11g 11n HT20 11n HT40 Conclusion PASS CH ANT0 6dB bandwidth MHz ANT1 Limit (khz) CH CH CH CH CH CH CH CH CH CH CH CH

64 FCC ID: RWO-RZ page 7-2 Test Mode 11b 11g 11n HT20 11n HT40 Conclusion PASS CH ANT0 99% Bandwidth MHz ANT1 Limit (khz) CH N/A CH N/A CH N/A CH N/A CH N/A CH N/A CH N/A CH N/A CH N/A CH N/A CH N/A CH N/A

65 FCC ID: RWO-RZ page 7-3 ANT0: Test Mode: IEEE b Test CH1: 2412MHz Test Mode: IEEE g Test CH1: 2412MHz Test CH6: 2437MHz Test CH6: 2437MHz Test CH11: 2462MHz Test CH11: 2462MHz

66 FCC ID: RWO-RZ page 7-4 Test Mode: IEEE n HT20 Test CH1: 2412MHz Test Mode: IEEE n HT40 Test CH3: 2422MHz Test CH6: 2437MHz Test CH6: 2437MHz Test CH11: 2462MHz Test CH9: 2452MHz

67 FCC ID: RWO-RZ page 7-5 ANT1: Test Mode: IEEE b Test CH1: 2412MHz Test Mode: IEEE g Test CH1: 2412MHz Test CH6: 2437MHz Test CH6: 2437MHz Test CH11: 2462MHz Test CH11: 2462MHz

68 FCC ID: RWO-RZ page 7-6 Test Mode: IEEE n HT20 Test CH1: 2412MHz Test Mode: IEEE n HT40 Test CH3: 2422MHz Test CH6: 2437MHz Test CH6: 2437MHz Test CH11: 2462MHz Test CH9: 2452MHz

69 FCC ID: RWO-RZ page OUTPUT POWER TEST 8.1. Test Equipment Item Equipment Manufacturer Model No. Serial No. Last Cal. Cal. Interval 1. Spectrum Agilent E4446A US Apr.24,16 1 Year 2. Spectrum Agilent N9030A MY Oct.18,15 1Year 3. Power meter Anritsu ML2487A 6K Apr.23,16 1Year 4. Power sensor Anritsu MA2491A Apr.23,16 1Year 5. Attenuator (20dB) Agilent 8491B MY Apr.23,16 1 Year 6. RF Cable Marvelous SFL402105FLEX Microwave Inc NO.1 Oct.17,15 1 Year 8.2. Limit (FCC Part 15C b(3)) For systems using digital modulation in the MHz, The Peak output Power shall not exceed 1W(30dBm), As an alternative to a peak power measurement, compliance with the one Watt limit can be based on a measurement of the maximum conducted output power. Maximum Conducted Output Power is defined as the total transmit power delivered to all antennas and antenna elements averaged across all symbols in the signaling alphabet when the transmitter is operating at its maximum power control level Test Procedure 1, Connected the EUT s antenna port to measure device by 26dB attenuator. 2, For IEEE b/g and IEEE802.11n HT20 modes, use a power meter which bandwidth is 20MHz, above the bandwidth of signals, to measure out output power in each mode. 3, For IEEE802.11n HT40 mode, since the signal bandwidth is nearly 40MHz, which is above 20MHz bandwidth of power sensor of ML2491A. use the test method descried in KDB clause ) Set the RBW=1MHz and VBW =3MHz 2) Set the span at least 1.5 times the OBW 3) Detector = RMS 4) Sweep time = auto couple 5) allow trace to fully stabilize 6) use the spectrum amalyser s integrated band power measurement function with band limits set equal to the EBW band edges. Note: The cable loss and attenuator loss were offset into measure device as an amplitude offset.

70 FCC ID: RWO-RZ page Test Results EUT: Notebook M/N: RZ Test date: Pressure: 102.6±1.0 kpa Humidity: 52.3±3.0% Tested by: Alice-Yang Test site: RF site Temperature:23.4±0.6 Test Mode 11b 11g 11n HT20 11n HT40 Conclusion: PASS CH Output Power dbm Limit (dbm) ANT 0 ANT 1 Total CH N/A 30 CH N/A 30 CH N/A 30 CH N/A 30 CH N/A 30 CH N/A 30 CH CH CH CH CH CH

71 FCC ID: RWO-RZ page 8-3 ANT0: Test Mode: IEEE n HT40 Test CH3: 2422MHz ANT1: Test Mode: IEEE n HT40 Test CH3: 2422MHz Test CH6: 2437MHz Test CH6: 2437MHz Test CH9: 2452MHz Test CH9: 2452MHz

72 FCC ID: RWO-RZ page POWER SPECTRAL DENSITY TEST 9.1. Test Equipment Item Equipment Manufacturer Model No. Serial No. Last Cal. Cal. Interval 1. Spectrum Agilent N9030A MY Oct.18,15 1Year 2. Attenuator (20dB) Agilent 8491B MY Apr.23,16 1 Year Marvelous 3. RF Cable SFL402105FLEX NO.1 Oct.17,15 1 Year Microwave Inc 9.2. Limit For digitally modulated systems, the power spectral density conducted from the intentional radiator to the antenna shall not be greater than 8dBm in any 3kHz band during any time interval of continuous transmission Test Procedure 1. Connected the EUT s antenna port to spectrum analyzer device by 20dB attenuator. 2. Set span to 1.5 times the DTS Bandwidth. 3. Set the RBW=3KHz, VBW=10KHz. 4. Detector=peak, Sweep time=auto, Trace mode=max Hold 5. All the trace to fully stabilize. 6. Use the peak marker function to determine the maximum amplitude level with in the RBW. Note: The cable loss and attenuator loss were offset into measure device as an amplitude

73 FCC ID: RWO-RZ page Test Results EUT: Notebook M/N: RZ Test date: Pressure: 102.5±1.0 kpa Humidity: 52.6±3.0% Tested by: Alice-Yang Test site: RF site Temperature:23.1±0.6 Test Mode 11b 11g 11n HT20 11n HT40 Conclusion: PASS CH Power Density dbm/3khz Limit (dbm/3khz) ANT 0 ANT 1 Total CH N/A 8 CH N/A 8 CH N/A 8 CH N/A 8 CH N/A 8 CH N/A 8 CH CH CH CH CH CH Note: For 11n mode, the direction gain less than 6dBi.

74 FCC ID: RWO-RZ page 9-3 ANT0: Test Mode: IEEE b Test CH1: 2412MHz Test Mode: IEEE g Test CH1: 2412MHz Test CH6: 2437MHz Test CH6: 2437MHz Test CH11: 2462MHz Test CH11: 2462MHz

75 FCC ID: RWO-RZ page 9-4 Test Mode: IEEE n HT20 Test CH1: 2412MHz Test Mode: IEEE n HT40 Test CH3: 2422MHz Test CH6: 2437MHz Test CH6: 2437MHz Test CH11: 2462MHz Test CH9: 2452MHz

76 FCC ID: RWO-RZ page 9-5 ANT1: Test Mode: IEEE b Test CH1: 2412MHz Test Mode: IEEE g Test CH1: 2412MHz Test CH6: 2437MHz Test CH6: 2437MHz Test CH11: 2462MHz Test CH11: 2462MHz

77 FCC ID: RWO-RZ page 9-6 Test Mode: IEEE n HT20 Test CH1: 2412MHz Test Mode: IEEE n HT40 Test CH3: 2422MHz Test CH6: 2437MHz Test CH6: 2437MHz Test CH11: 2462MHz Test CH9: 2452MHz

78 FCC ID: RWO-RZ page ANTENNA REQUIREMENT Standard Applicable For intentional device, according to FCC 47 CFR Section , an intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. And according to FCC 47 CFR Section (b), if transmitting antennas of directional gain greater than 6dBi are used, the power shall be reduced by the amount in db that the directional gain of the antenna exceeds 6dBi Antenna Connected Construction The antennas used for this product are PIFA antenna that no antenna other than that furnished by the responsible party shall be used with the device, the maximum peak gain of the transmit antenna is 3.91dBi.

79 FCC ID: RWO-RZ page DEVIATION TO TEST SPECIFICATIONS [ NONE]