Digital Input Module. ST-1xxx. User Manual CREVIS Co.,Ltd. Version FnIO S-Series
|
|
|
- Gladys Merritt
- 5 years ago
- Views:
Transcription
1 1 FnIO S-Series Digital Input Module ST-1xxx User Manual Version CREVIS Co.,Ltd
2 2 FnIO S-Series DOCUMENT CHANGE SUMMARY REV PAGE REMARKS DATE EDITOR 1.0 New Document 2011/10/07 JE KANG , Add your experience Change : ST-1804, ST-1904 Off voltage ST-1804, ST-1904 Image 2012/1/13 JE KANG
3 3 FnIO S-Series Table of Contents 1. Important Notes Safety Instruction Symbols Safety Notes Certification DIGITAL INPUT MODULE LIST Specification The Interface ST ST-111F ST ST-112F ST ST ST-121F ST ST ST-122F ST ST-131F ST ST-132F... 23
4 4 FnIO S-Series ST ST Environment Specification Specification ST ST-111F ST ST-112F ST ST ST-121F ST ST ST-122F ST ST-131F ST ST-132F ST ST Dimension ST-1xx4, ST-1xx ST-1xxF... 44
5 5 FnIO S-Series 5. Mapping Data into the image Table ST-1xx ST-1xx ST-1xxF Trouble Shooting... 46
6 6 FnIO S-Series 1. Important Notes Solid state equipment has operational characteristics differing from those of electromechanical equipment. Safety Guidelines for the Application, Installation and Maintenance of Solid State Controls describes some important differences between solid state equipment and hard-wired electromechanical devices. Because of this difference, and also because of the wide variety of uses for solid state equipment, all persons responsible for applying this equipment must satisfy themselves that each intended application of this equipment is acceptable. In no event will CREVIS be responsible or liable for indirect or consequential damages resulting from the use or application of this equipment. The examples and diagrams in this manual are included solely for illustrative purposes. Because of the many variables and requirements associated with any particular installation, CREVIS cannot assume responsibility or liability for actual use based on the examples and diagrams. Warning! If you don t follow the directions, it could cause a personal injury, damage to the equipment or explosion Do not assemble the products and wire with power applied to the system. Else it may cause an electric arc, which can result into unexpected and potentially dangerous action by field devices. Arching is explosion risk in hazardous locations. Be sure that the area is non-hazardous or remove system power appropriately before assembling or wiring the modules. Do not touch any terminal blocks or IO modules when system is running. Else it may cause the unit to an electric shock or malfunction. Keep away from the strange metallic materials not related to the unit and wiring works should be controlled by the electric expert engineer. Else it may cause the unit to a fire, electric shock or malfunction.
7 7 FnIO S-Series Caution! If you disobey the instructions, there may be possibility of personal injury, damage to equipment or explosion. Please follow below Instructions. Check the rated voltage and terminal array before wiring. Avoid the circumstances over 50 of temperature. Avoid placing it directly in the sunlight. Avoid the place under circumstances over 85% of humidity. Do not place Modules near by the inflammable material. Else it may cause a fire. Do not permit any vibration approaching it directly. Go through module specification carefully, ensure inputs, output connections are made with the specifications. Use standard cables for wiring. Use Product under pollution degree 2 environment Safety Instruction Symbols Identifies information about practices or circumstances that can cause an explosion in a hazardous environment, which may lead to personal injury or death property damage, or economic loss Identifies information that is critical for successful application and understanding of the product Identifies information about practices or circumstances that can lead to personal injury, property damage, or economic loss. Attentions help you to identity a hazard, avoid a hazard, and recognize the consequences Safety Notes The modules are equipped with electronic components that may be destroyed by electrostatic discharge. When handling the modules, ensure that the environment (persons, workplace and packing) is well grounded. Avoid touching conductive components, e.g. FnBUS Pin.
8 8 FnIO S-Series Certification c-ul-us UL Listed Industrial Control Equipment, certified for U.S. and Canada See UL File E DNV CERTIFICATE No. A CE Certificate EN ; Industrial Immunity EN ; Industrial Emissions
9 9 FnIO S-Series 2. DIGITAL INPUT MODULE LIST ST-Number Description ID(hex) ST Points, Sink(Positive), 5Vdc, Terminal Active ST-111F 16 Points, Sink(Positive), 5Vdc, 20P Connector Active ST Points, Source(Negative), 5Vdc, Terminal Active ST-112F 16 Points, Source(Negative), 5Vdc, 20P Connector A Active ST Points, Sink(Positive), 12V/24Vdc, Terminal Active ST Points, Sink(Positive), 12V/24Vdc, Terminal Active ST-121F 16 Points, Sink(Positive), 12V/24Vdc, 20P Connector Active ST Points, Source(Negative), 12V/24Vdc, Terminal Active ST Points, Source(Negative), 12V/24Vdc, Terminal Active ST-122F 16 Points, Source(Negative), 12V/24Vdc, 20P Connector Active ST Points, Sink(Positive), 48Vdc, Terminal Active ST-131F 16 Points, Sink(Positive), 48Vdc, 20P Connector Active ST Points, Source(Negative), 48Vdc, Terminal Active ST-132F 16 Points, Source(Negative), 48Vdc, 20P Connector Active ST Points, 110Vac, Terminal Active Production Status ST Points, 220Vac, Terminal A Active
10 10 FnIO S-Series 3. Specification 3.1. The Interface ST-1114 Pin No. Description Pin No. Description 0 Input Channel 0 1 Input Channel 1 2 Input Channel 2 3 Input Channel 3 4 Field Ground (0V) 5 Field Ground (0V) 6 Field Power (+5Vdc) 7 Field Power (+5Vdc)
11 11 FnIO S-Series ST-111F Pin No. Description Pin No. Description 1 Input Channel 0 2 Input Channel 1 3 Input Channel 2 4 Input Channel 3 5 Input Channel 4 6 Input Channel 5 7 Input Channel 6 8 Input Channel 7 9 Input Channel 8 10 Input Channel 9 11 Input Channel Input Channel Input Channel Input Channel Input Channel Input Channel Field Ground(0V) 18 Field Ground(0V) 19 Field Power (+5Vdc) 20 Field Power (+5Vdc)
12 12 FnIO S-Series ST-1124 Pin No. Description Pin No. Description 0 Input Channel 0 1 Input Channel 1 2 Input Channel 2 3 Input Channel 3 4 Field Ground (0V) 5 Field Ground (0V) 6 Field Power (+5Vdc) 7 Field Power (+5Vdc)
13 13 FnIO S-Series ST-112F Pin No. Description Pin No. Description 1 Input Channel 0 2 Input Channel 1 3 Input Channel 2 4 Input Channel 3 5 Input Channel 4 6 Input Channel 5 7 Input Channel 6 8 Input Channel 7 9 Input Channel 8 10 Input Channel 9 11 Input Channel Input Channel Input Channel Input Channel Input Channel Input Channel Field Ground(0V) 18 Field Ground(0V) 19 Field Power (+5Vdc) 20 Field Power (+5Vdc)
14 14 FnIO S-Series ST-1214 Pin No. Description Pin No. Description 0 Input Channel 0 1 Input Channel 1 2 Input Channel 2 3 Input Channel 3 4 Field Ground (0V) 5 Field Ground (0V) 6 Field Power (+24Vdc) 7 Field Power (+24Vdc)
15 15 FnIO S-Series ST-1218 Pin No. Description Pin No. Description 0 Input Channel 0 1 Input Channel 1 2 Input Channel 2 3 Input Channel 3 4 Input Channel 4 5 Input Channel 5 6 Input Channel 6 7 Input Channel 7
16 16 FnIO S-Series ST-121F Pin No. Description Pin No. Description 1 Input Channel 0 2 Input Channel 1 3 Input Channel 2 4 Input Channel 3 5 Input Channel 4 6 Input Channel 5 7 Input Channel 6 8 Input Channel 7 9 Input Channel 8 10 Input Channel 9 11 Input Channel Input Channel Input Channel Input Channel Input Channel Input Channel Field Ground(0V) 18 Field Ground(0V) 19 Field Power (+24Vdc) 20 Field Power (+24Vdc)
17 17 FnIO S-Series ST-1224 Pin No. Description Pin No. Description 0 Input Channel 0 1 Input Channel 1 2 Input Channel 2 3 Input Channel 3 4 Field Ground (0V) 5 Field Ground (0V) 6 Field Power (+24Vdc) 7 Field Power (+24Vdc)
18 18 FnIO S-Series ST-1228 Pin No. Description Pin No. Description 0 Input Channel 0 1 Input Channel 1 2 Input Channel 2 3 Input Channel 3 4 Input Channel 4 5 Input Channel 5 6 Input Channel 6 7 Input Channel 7
19 19 FnIO S-Series ST-122F Pin No. Description Pin No. Description 1 Input Channel 0 2 Input Channel 1 3 Input Channel 2 4 Input Channel 3 5 Input Channel 4 6 Input Channel 5 7 Input Channel 6 8 Input Channel 7 9 Input Channel 8 10 Input Channel 9 11 Input Channel Input Channel Input Channel Input Channel Input Channel Input Channel Field Ground(0V) 18 Field Ground(0V) 19 Field Power (+24Vdc) 20 Field Power (+24Vdc)
20 20 FnIO S-Series ST-1314 Pin No. Description Pin No. Description 0 Input Channel 0 1 Input Channel 1 2 Input Channel 2 3 Input Channel 3 4 Field Ground (0V) 5 Field Ground (0V) 6 Field Power (+48Vdc) 7 Field Power (+48Vdc)
21 21 FnIO S-Series ST-131F Pin No. Description Pin No. Description 1 Input Channel 0 2 Input Channel 1 3 Input Channel 2 4 Input Channel 3 5 Input Channel 4 6 Input Channel 5 7 Input Channel 6 8 Input Channel 7 9 Input Channel 8 10 Input Channel 9 11 Input Channel Input Channel Input Channel Input Channel Input Channel Input Channel Field Ground(0V) 18 Field Ground(0V) 19 Field Power (+48Vdc) 20 Field Power (+48Vdc)
22 22 FnIO S-Series ST-1324 Pin No. Description Pin No. Description 0 Input Channel 0 1 Input Channel 1 2 Input Channel 2 3 Input Channel 3 4 Field Ground (0V) 5 Field Ground (0V) 6 Field Power (+48Vdc) 7 Field Power (+48Vdc)
23 23 FnIO S-Series ST-132F Pin No. Description Pin No. Description 1 Input Channel 0 2 Input Channel 1 3 Input Channel 2 4 Input Channel 3 5 Input Channel 4 6 Input Channel 5 7 Input Channel 6 8 Input Channel 7 9 Input Channel 8 10 Input Channel 9 11 Input Channel Input Channel Input Channel Input Channel Input Channel Input Channel Field Ground(0V) 18 Field Ground(0V) 19 Field Power (+48Vdc) 20 Field Power (+48Vdc)
24 24 FnIO S-Series ST-1804 Pin No. Description Pin No. Description 0 Input Channel 0 1 Input Channel 1 2 Input Channel 2 3 Input Channel 3 4 L1 5 L1 6 L2 7 L2
25 25 FnIO S-Series ST-1904 Pin No. Description Pin No. Description 0 Input Channel 0 1 Input Channel 1 2 Input Channel 2 3 Input Channel 3 4 L1 5 L1 6 L2 7 L2
26 26 FnIO S-Series 3.2. Environment Specification Environmental Specifications Operating Temperature Non-Operating Temperature Relative Humidity Operating Altitude Mounting General Specifications Shock Operating Shock Non-Operating Vibration/Shock resistance -20 to 50 0 to to 85 5%~90% non-condensing 2000m DIN rail 10g 30g Displacement : 0.012Inch p-p from 10~57Hz Acceleration : 2G s from 57~500Hz Sweep Rate : 1 octave Per Minute Axes to test : x, y, z Frequency Sweeps Per Axis : 10 EMC resistance burst/esd EMI Installation Pos. /Protect. Class Product Certification Network Conformance Isolation Confirms to EN Confirms to EN Variable / IP20 UL / cul, CE NA-9111 : ODVA Conformance Test Completion NA-9122 : PTO Conformance Test Completion NA-9131 : CLPA Conformance Test Completion DC Module (Included Analog Module) : Terminal Block to F.G 500Vac/1min AC Module : Terminal Block to F.G 1500Vac/1min Relay Module : Terminal Block to F.G 2500Vac/1min
27 27 FnIO S-Series 3.3. Specification ST-1114 Items Specification Input Specification Inputs Per Module 4 Points Sink Type Indicators 4 Green Input States, 1 Green/Red FnBUS State ON-state Voltage 5Vdc nominal Min. 2.4Vdc ~ Max. 5.5Vdc Min. OFF-state Voltage Max. 0.8Vdc ON-state Current Max. 4.5mA / 5.5Vdc Input Signal Delay OFF to ON: Max. 0.5ms ON to OFF: Max. 0.5ms Nominal Input Impedance Typ. 1.3KΩ Filtering Time Typ. 1.5ms Common Type 4 Points / 2COM (Single Common) General Specification Power Dissipation Max. 5.0Vdc Isolation I/O to Logic : Photocoupler isolation Field Power Supply Voltage : 5Vdc nominal Voltage Range : 4.5~5.5Vdc Wiring I/O Cable Max. 2.0mm 2 (AWG 14) Weight 70g Module Size 12mm ⅹ 99mm ⅹ 70mm Environment Condition Refer to " Environment Specification"(page : 25)
28 28 FnIO S-Series ST-111F Items Input Specification Inputs Per Module Indicators ON-state Voltage Min. OFF-state Voltage ON-state Current Input Signal Delay Input Impedance Filtering Time Common Type General Specification Power Dissipation Isolation Field Power Wiring Weight Module Size Specification 16 Points Sink Type 16 Green Input States, 1 Green/Red FnBUS State 5Vdc nominal Min. 4.5Vdc ~ Max. 5.5Vdc Max. 0.8Vdc Max. 4.5mA / 5.5Vdc Max. 3.0ms Typ. 1KΩ Typ. 1.5ms 16 Points / 2COM Max. 5.0Vdc I/O to Logic : Photocoupler isolation Supply Voltage : 5Vdc nominal Voltage Range : 4.5~5.5Vdc Power Dissipation: Max. 70mA@5Vdc Connector Type, up to AWG22 Module Connector : HIF3BA-20D-2.54DSA 70g 12mm ⅹ 99mm ⅹ 70mm Environment Condition Refer to " Environment Specification"(page : 25)
29 29 FnIO S-Series ST-1124 Items Specification Input Specification Inputs Per Module 4 Points Source Type Indicators 4 Green Input States, 1 Green/Red FnBUS State ON-state Voltage 5Vdc nominal Min. 2.4Vdc ~ Max. 5.5Vdc Min. OFF-state Voltage Max. 0.8Vdc ON-state Current Max. 4.5mA / 5.5Vdc Input Signal Delay OFF to ON: Max. 0.5ms ON to OFF: Max. 0.5ms Nominal Input Impedance Typ. 1.3KΩ Filtering Time Typ. 1.5ms Common Type 4 Points / 2COM (Single Common) General Specification Power Dissipation Max. 5.0Vdc Isolation I/O to Logic : Photocoupler isolation Field Power Supply Voltage : 5Vdc nominal Voltage Range : 4.5~5.5Vdc Wiring I/O Cable Max. 2.0mm 2 (AWG 14) Weight 70g Module Size 12mm ⅹ 99mm ⅹ 70mm Environment Condition Refer to " Environment Specification"(page : 25)
30 30 FnIO S-Series ST-112F Items Input Specification Inputs Per Module Indicators ON-state Voltage Min. OFF-state Voltage ON-state Current Input Signal Delay Filtering Time Common Type General Specification Power Dissipation Isolation Field Power Wiring Weight Module Size Specification 16 Points Source Type 16 Green Input States, 1 Green/Red FnBUS State 5Vdc nominal Min. 4.5Vdc ~ Max. 5.5Vdc Max. 0.8Vdc Max. 4.5mA / 5.5Vdc Max. 3.0ms Typ. 1.5ms 16 Points / 2COM Max. 5.0Vdc I/O to Logic : Photocoupler isolation Supply Voltage : 5Vdc nominal Voltage Range : 4.5~5.5Vdc Power Dissipation: Max. 70mA@5Vdc Connector Type, up to AWG22 Module Connector : HIF3BA-20D-2.54DSA 70g 12mm ⅹ 99mm ⅹ 70mm Environment Condition Refer to " Environment Specification"(page : 25)
31 31 FnIO S-Series ST-1214 Items Specification Input Specification Inputs Per Module 4 Points Sink Type Indicators 4 Green Input States, 1 Green/Red FnBUS State ON-state Voltage 24Vdc nominal Min. 10.2Vdc ~ Max. 28.8Vdc Min. OFF-state Voltage Max. 5Vdc ON-state Current Max. 6mA / 28.8Vdc Input Signal Delay OFF to ON: Max. 3ms ON to OFF: Max. 3ms Nominal Input Impedance Typ. 5.1KΩ Filtering Time Typ. 1.5ms Common Type 4 Points / 2COM (Single Common) General Specification Power Dissipation Max. 5.0Vdc Isolation I/O to Logic : Photocoupler isolation Field Power Supply Voltage : 24Vdc nominal Voltage Range : 11~28.8Vdc Wiring I/O Cable Max. 2.0mm 2 (AWG 14) Weight 70g Module Size 12mm ⅹ 99mm ⅹ 70mm Environment Condition Refer to " Environment Specification"(page : 25)
32 32 FnIO S-Series ST-1218 Items Specification Input Specification Inputs Per Module 8 Points Sink Type Indicators 8 Green Input States, 1 Green/Red FnBUS State ON-state Voltage 24Vdc nominal Min. 10.2Vdc ~ Max. 28.8Vdc Min. OFF-state Voltage Max. 5Vdc ON-state Current Max. 6mA / 28.8Vdc Input Signal Delay OFF to ON: Max. 3ms ON to OFF: Max. 3ms Nominal Input Impedance Typ. 5.1KΩ Filtering Time Typ. 1.5ms Common Type External Common General Specification Power Dissipation Max. 5.0Vdc Isolation I/O to Logic : Photocoupler isolation Field Power Supply Voltage : 24Vdc nominal Voltage Range : 11~28.8Vdc Wiring I/O Cable Max. 2.0mm 2 (AWG 14) Weight 70g Module Size 12mm ⅹ 99mm ⅹ 70mm Environment Condition Refer to " Environment Specification"(page : 25)
33 33 FnIO S-Series ST-121F Items Input Specification Inputs Per Module Indicators ON-state Voltage Min. OFF-state Voltage ON-state Current Input Signal Delay Nominal Input Impedance Filtering Time Common Type General Specification Power Dissipation Isolation Field Power Wiring Weight Module Size Specification 16 Points Sink Type 16 Green Input States, 1 Green/Red FnBUS State 24Vdc nominal Min. 10.2Vdc ~ Max. 28.8Vdc Max. 5Vdc Max. 6mA / 28.8Vdc OFF to ON: Max. 3ms ON to OFF: Max. 3ms Typ. 5.1KΩ Typ. 1.5ms 16 Points / 2COM Max. 5.0Vdc I/O to Logic : Photocoupler isolation Supply Voltage : 24Vdc nominal Voltage Range : 11~28.8Vdc Power Dissipation : 5mA@28.8Vdc Per Point Module Connector : HIF3BA-20D-2.54DSA 70g 12mm ⅹ 99mm ⅹ 70mm Environment Condition Refer to " Environment Specification"(page : 25)
34 34 FnIO S-Series ST-1224 Items Specification Input Specification Inputs Per Module 4 Points Source Type Indicators 4 Green Input States, 1 Green/Red FnBUS State ON-state Voltage 24Vdc nominal Min. 10.2Vdc ~ Max. 28.8Vdc Min. OFF-state Voltage Max. 5Vdc ON-state Current Max. 6mA / 28.8Vdc Input Signal Delay OFF to ON: Max. 3ms ON to OFF: Max. 3ms Nominal Input Impedance Typ. 5.1KΩ Common Type 4 Points / 2COM (Single Common) General Specification Power Dissipation Max. 5.0Vdc Isolation I/O to Logic : Photocoupler isolation Field Power Supply Voltage : 24Vdc nominal Voltage Range : 11~28.8Vdc Wiring I/O Cable Max. 2.0mm 2 (AWG 14) Weight 70g Module Size 12mm ⅹ 99mm ⅹ 70mm Environment Condition Refer to " Environment Specification"(page : 25)
35 35 FnIO S-Series ST-1228 Items Specification Input Specification Inputs Per Module 8 Points Source Type Indicators 8 Green Input States, 1 Green/Red FnBUS State ON-state Voltage 24Vdc nominal Min. 10.2Vdc ~ Max. 28.8Vdc Min. OFF-state Voltage Max. 5Vdc ON-state Current Max. 6mA / 28.8Vdc Input Signal Delay OFF to ON: Max. 3ms ON to OFF: Max. 3ms Nominal Input Impedance Typ. 5.1KΩ Filtering Time Typ. 1.5ms Common Type External Common General Specification Power Dissipation Max. 5.0Vdc Isolation I/O to Logic : Photocoupler isolation Field Power Supply Voltage : 24Vdc nominal Voltage Range : 11~28.8Vdc Wiring I/O Cable Max. 2.0mm 2 (AWG 14) Weight 70g Module Size 12mm ⅹ 99mm ⅹ 70mm Environment Condition Refer to " Environment Specification"(page : 25)
36 36 FnIO S-Series ST-122F Items Input Specification Inputs Per Module Indicators ON-state Voltage Min. OFF-state Voltage ON-state Current Input Signal Delay Filtering Time Common Type General Specification Power Dissipation Isolation Field Power Wiring Weight Module Size Specification 16 Points Source Type 16 Green Input States, 1 Green/Red FnBUS State 24Vdc nominal Min. 10.2Vdc ~ Max. 28.8Vdc Max. 5Vdc Max. 6mA / 28.8Vdc OFF to ON: Max. 3ms ON to OFF: Max. 3ms Typ. 1.5ms 16 Points / 2COM Max. 5.0Vdc I/O to Logic : Photocoupler isolation Supply Voltage : 24Vdc nominal Voltage Range : 11~28.8Vdc Power Dissipation : 5mA@28.8Vdc Per Point Module Connector : HIF3BA-20D-2.54DSA 70g 12mm ⅹ 99mm ⅹ 70mm Environment Condition Refer to " Environment Specification"(page : 25)
37 37 FnIO S-Series ST-1314 Items Specification Input Specification Inputs Per Module 4 Points Sink Type Indicators 4 Green Input States, 1 Green/Red FnBUS State ON-state Voltage 48Vdc nominal Min. 34Vdc ~ Max. 60Vdc Min. OFF-state Voltage Max. 10Vdc ON-state Current Max. 4mA / 48Vdc Input Signal Delay OFF to ON: Max. 3ms ON to OFF: Max. 3ms Nominal Input Impedance Typ. 12KΩ Common Type 4 Points / 2COM (Single Common) General Specification Power Dissipation Max. 5.0Vdc Isolation I/O to Logic : Photocoupler isolation Field Power Supply Voltage : 48Vdc nominal Voltage Range : 34~60Vdc Wiring I/O Cable Max. 2.0mm 2 (AWG 14) Weight 70g Module Size 12mm ⅹ 99mm ⅹ 70mm Environment Condition Refer to " Environment Specification"(page : 25)
38 38 FnIO S-Series ST-131F Items Input Specification Inputs Per Module Indicators ON-state Voltage Min. OFF-state Voltage ON-state Current Input Signal Delay Nominal Input Impedance Filtering Time Common Type General Specification Power Dissipation Isolation Field Power Wiring Weight Module Size Specification 16 Points Sink Type 16 Green Input States, 1 Green/Red FnBUS State 48Vdc nominal Min. 34Vdc ~ Max. 60Vdc Max. 20Vdc Max. 2.5mA / 60Vdc OFF to ON: Max. 3ms ON to OFF: Max. 3ms Typ. 27KΩ Typ. 1.5ms 16 Points / 2COM Max. 5.0Vdc I/O to Logic : Photocoupler isolation Supply Voltage : 48Vdc nominal Voltage Range : 34~60Vdc Power Dissipation : Max, 45mA@48Vdc Connector Type, up to AWG22 Module Connector : HIF3BA-20D-2.54DSA 70g 12mm ⅹ 99mm ⅹ 70mm Environment Condition Refer to " Environment Specification"(page : 25)
39 39 FnIO S-Series ST-1324 Items Specification Input Specification Inputs Per Module 4 Points Source Type Indicators 4 Green Input States, 1 Green/Red FnBUS State ON-state Voltage 48Vdc nominal Min. 34Vdc ~ Max. 60Vdc Min. OFF-state Voltage Max. 10Vdc ON-state Current Max. 4mA / 48Vdc Input Signal Delay OFF to ON: Max. 3ms ON to OFF: Max. 3ms Nominal Input Impedance Typ. 12KΩ Common Type 4 Points / 2COM (Single Common) General Specification Power Dissipation Max. 5.0Vdc Isolation I/O to Logic : Photocoupler isolation Field Power Supply Voltage : 48Vdc nominal Voltage Range : 34~60Vdc Wiring I/O Cable Max. 2.0mm 2 (AWG 14) Weight 70g Module Size 12mm ⅹ 99mm ⅹ 70mm Environment Condition Refer to " Environment Specification"(page : 25)
40 40 FnIO S-Series ST-132F Items Input Specification Inputs Per Module Indicators ON-state Voltage Min. OFF-state Voltage ON-state Current Input Signal Delay Nominal Input Impedance Filtering Time Common Type General Specification Power Dissipation Isolation Field Power Wiring Weight Module Size Specification 16 Points Source Type 16 Green Input States, 1 Green/Red FnBUS State 48Vdc nominal Min. 34Vdc ~ Max. 60Vdc Max. 20Vdc Max. 2.5mA / 60Vdc OFF to ON: Max. 3ms ON to OFF: Max. 3ms Typ. 27KΩ Typ. 1.5ms 16 Points / 2COM Max. 5.0Vdc I/O to Logic : Photocoupler isolation Supply Voltage : 48Vdc nominal Voltage Range : 34~60Vdc Power Dissipation : Max, 45mA@48Vdc Connector Type, up to AWG22 Module Connector : HIF3BA-20D-2.54DSA 70g 12mm ⅹ 99mm ⅹ 70mm Environment Condition Refer to " Environment Specification"(page : 25)
41 41 FnIO S-Series ST-1804 Items Specification Input Specification Inputs Per Module 4 Points Indicators 4 Green Input States, 1 Green/Red FnBUS State ON-state Voltage 110Vac nominal Min. 85Vac ~ Max. 132Vdc Min. OFF-state Voltage Max. 60Vac ON-state Current Max. 8mA / 132Vdc Input Signal Delay OFF to ON: Max. 10ms ON to OFF: Max. 10ms Nominal Input Impedance Typ. 11KΩ Frequency Range 47-63Hz Common Type 4 Points / 2COM (Single Common) General Specification Power Dissipation Max. 5.0Vdc Isolation I/O to Logic : Photocoupler isolation Field Power Supply Voltage : 120Vac nominal Voltage Range: Min. 85Vac ~ Max. 132Vac Wiring I/O Cable Max. 2.0mm 2 (AWG 14) Weight 70g Module Size 12mm ⅹ 99mm ⅹ 70mm Environment Condition Refer to " Environment Specification"(page : 25)
42 42 FnIO S-Series ST-1904 Items Specification Input Specification Inputs Per Module 4 Points Indicators 4 Green Input States, 1 Green/Red FnBUS State ON-state Voltage 220Vac nominal Min. 170Vac ~ Max. 264Vdc Min. OFF-state Voltage Max. 130Vac ON-state Current Max. 12mA / 264Vdc Input Signal Delay OFF to ON: Max. 10ms ON to OFF: Max. 10ms Nominal Input Impedance Typ. 22KΩ Frequency Range 47-63Hz Common Type 4 Points / 2COM (Single Common) General Specification Power Dissipation Max. 5.0Vdc Isolation I/O to Logic : Photocoupler isolation Field Power Supply Voltage : 240Vac nominal Voltage Range: Min. 170Vac ~ Max. 264Vac Wiring I/O Cable Max. 2.0mm 2 (AWG 14) Weight 70g Module Size 12mm ⅹ 99mm ⅹ 70mm Environment Condition Refer to " Environment Specification"(page : 25)
43 43 FnIO S-Series 4. Dimension 4.1. ST-1xx4, ST-1xx8 (mm)
44 44 FnIO S-Series 4.2. ST-1xxF
45 45 FnIO S-Series 5. Mapping Data into the image Table 5.1. ST-1xx4 Input Module Data D3 D2 D1 D0 Input Image Value Bit No Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Byte 0 Reserved D3 D2 D1 D ST-1xx8 Input Module Data D7 D6 D5 D4 D3 D2 D1 D0 Input Image Value Bit No Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Byte 0 D7 D6 D5 D4 D3 D2 D1 D ST-1xxF Input Module Data D7 D6 D5 D4 D3 D2 D1 D0 D15 D14 D13 D12 D11 D10 D9 D8 Input Image Value Bit No Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Byte 0 D7 D6 D5 D4 D3 D2 D1 D0 Byte 1 D15 D14 D13 D12 D11 D10 D9 D8
46 46 FnIO S-Series 6. Trouble Shooting In this manual, it couldn t be described all variety case with Network Adapter of several protocols. So if you couldn t find any fault after investigating all below cases refer to NA user manual. LED Status Cause Action EXPANSION MODULE STATUS LED Off Green Flashing Green Flashing Red Red Not Power No Initialized Fn-Bus Connection Fn-Bus Ready Fn-Bus Fault Device Fault Device has no expansion Module or may not be powered The Parameter is not initialized yet. FnBus normal Operation FnBus ready FnBus Time Out, FnBus Failed Communication Device fault CHANNEL STATUS LED Off Not Signal Normal Operation Green On Signal Normal Operation
High Speed Counter. User Manual CREVIS Co.,Ltd. Version FnIO S-Series
1 FnIO S-Series High Speed Counter ST-5101 ST-5112 ST-5111 ST-5114 User Manual Version 1.04 2013 CREVIS Co.,Ltd 2 FnIO S-Series DOCUMENT CHANGE SUMMARY REV PAGE REMARKS DATE EDITOR 1.0 New Document Draft
02/11/2015
Smart range with Removable Terminal blocks XD26RBT Smart Part number 88974561 Designed for industrial, commercial, medical and paramedical machines Faster maintenance process which improves the machine
UniStream Uni-I/O Modules
UniStream Uni-I/O Modules UID-0808THS This guide provides specifications for Unitronics Uni-I/O module UID-0808THS. This module can be set with up to 2 Shaft Encoders at 250kHz, or up to 2 High Speed PWM
UniStream Uni-I/O Modules
UniStream Uni-I/O Modules Technical Specifications UIS-WCB1 This guide provides specifications for Unitronics Uni-I/O Wide module UIS-WCB1. This module comprises: 10 Digital inputs, 24VDC, sink/source,
08/07/2015
17.5 mm - 1 Solid State Relay 0.7A MUS2 Part number 88827004 Multi-function or mono-function Multi-range Multi-voltage Screw or spring terminals LED status indicator (relay version) Possibility of external
Installation Instructions Space Temperature Transmitter
Installation Instructions Space Temperature Transmitter Catalog Number(s) 1414-CTZ03PBRAA, 1414-CTD03PBRAA, 1414-CTO03PBRAA, 1414-CTS03PBRAA, 1414-CTT03PBRAA, 1414-ITS03PBRAA, 1414-ITT03SBRAA, 1414-ITZ02GBRAA,
ATSU01N232LT soft starter for asynchronous motor - ATSU01-32 A V KW
Characteristics soft starter for asynchronous motor - ATSU01-32 A - 200..480V - 7.5..15 KW Main Range of product Product or component type Product destination Product specific application Device short
ATSU01N222LT soft starter for asynchronous motor - ATSU01-22 A V KW
Characteristics soft starter for asynchronous motor - ATSU01-22 A - 200..480 V - 4..11 KW Price* : 195.00 GBP Main Range of product Product or component type Product destination Product specific application
UniStream Remote I/O
UniStream Remote I/O User Manual Revision 1.01 September, 2018 Unitronics 1 08/18 Contents Unitronics Remote I/O Models... 5 Adapter... 5 Input Models... 5 Output Models... 6 Power Models... 6 Environmental...
DSA150 Series. xxx Series. 150 Watts. AC-DC Power Supplies. Models & Ratings. Mechanical Details 3.92 (99.8) 2.18 (55.5) 4.92 (125.
15 Watts xxx Series Ultra Slim Design 15% Peak Load for 3 seconds Ambient Operation from -1 C to +7 C High Efficiency Selectable Overload Characteristic Selectable Remote Inhibit or Enable 3 Year Warranty
RAD-IN/OUT-8D. Digital extension modules for the bidirectional wireless system. INTERFACE Data sheet _en_05. 1 Description
RAD-IN/OUT-D Digital extension modules for the bidirectional wireless system INTERFACE Data sheet 102122_en_0 PHOENIX CONTACT 2010-02-2 1 Description The RAD-ISM-...-SET-BD-BUS-ANT bidirectional wireless
Switching Power Supply Type SPP1 60W Enclosed type
Type SPP1 60W Enclosed type Universal AC input full range Short circuit protection Internal input filter High efficiency High average efficiency (meets ErP) Low stand-by power consumption CE, TUV, and
02/11/2015
Modem communication plug and play solutions GSM Part number 88970119 For remote control of your application Automatic notification of alarms via SMS (GSM Modem) / email or on a PC with M3 ALARM software.
05/09/2012
17.5 mm EMER8 Part number 88829198 Multifunction or mono-function Multi-range (7 ranges) Multi-voltage or single voltage Screw terminals LED status indicator (1 voltage present LED, 1 timer ON LED) Option
em4 local - Robust Specific characteristics Part number
em4 em4 local em4 local Very compact and easy to program nanoplc Save time in designing your application using the most intuitive graphical function block language of the market Measure accurately your
TPP 40 Series, 40 Watt. Order code Output voltage Output current max. Efficiency. max. screw terminal pin connector Vout 1 Vout 2 Vout 3
, Features High power density 40 W power supply (enclosed / open frame) 2 x MOPP Medical safety according to AAMI/ANSI ES 60601-1:2005(R) and IEC/EN 60601-1 3rd edition Ready to meet ErP directive, < 0.3
ATS22C21Q soft starter-ats22-control 220V-power 230V(55kW)/ V(110kW)
Characteristics soft starter-ats22-control 220V-power 230V(55kW)/400...440V(110kW) Product availability : Non-Stock - Not normally stocked in distribution facility Price* : 2383.00 USD Main Range of product
LDC240 Series is a single phase, ultra compact DIN Rail Switching Power Supply with active PFC, ideal for many applications.
LDC240 Series is a single phase, ultra compact DIN Rail Switching Power Supply with active PFC, ideal for many applications. Its compact size, high efficiency, excellent reliability together with easy
02/11/2015
17.5 mm - 1 Relay 5A EMER8 Part number 88829198 Multifunction or mono-function Multi-range (7 ranges) Multi-voltage or single voltage Screw terminals LED status indicator (1 voltage present LED, 1 timer
PLC-K506 Series FEATURES DESCRIPTION FEATURES
FEATURES Two High Speed Counters Two Pulse Train Outputs Two Pulse Width Modulation Outputs Inputs 10 Outputs 1 RS232 Port 2 RS485 Ports Supports Modbus RTU Protocol Communicate With Up to 32 Devices DESCRIPTION
02/11/2015
Modem communication plug and play solutions GSM Part number 88970119 For remote control of your application Automatic notification of alarms via SMS (GSM Modem) / email or on a PC with M3 ALARM software.
Select G3PA SSRs and G32A Cartridges to be Discontinued; Replace with G3PA-X or G3PJ Relays, G32A-A-X Cartridges
NO: RL-159 PRODUCT: G3PA SSRs, G32A Cartridges DATE: January 2017 TYPE: Partial Discontinuation Notice Select G3PA SSRs and G32A Cartridges to be Discontinued; Replace with G3PA-X or G3PJ Relays, G32A-A-X
02/11/2015
"Compact" range with display CD12 Part number 88970041 Green LCD with 4 lines of 18 characters and configurable backlighting More cost effective solution Industrial temperature range (-20 C +55 C) Analogue
ATS01N206QN soft starter for asynchronous motor - ATS01-6 A V KW
Characteristics soft starter for asynchronous motor - ATS01-6 A - 380..415V - 1.5..3 KW Main Range of product Altistart 01 Product or component type Product destination Product specific application Device
All specifications valid at normal input voltage, full load and +25 C after warm-up time unless otherwise stated.
KEY FEATURES Din Rail Switching Power Supply 180 Watt with 18CFM FAN for 12V to 48V Output Voltage 150 Watt with 30CFM FAN for 5V Output Voltage High Efficiency up to 93% Universal Input: 90-264 VAC Low
02/11/2015
Smart "Compact" range with display CD20 Smart Part number 88974053 Highly visible blue LCD with 4 lines of 18 characters and configurable backlighting Allow the use of the entire library of specific functions
em4 em4 alert em4 alert 2G
em4 em4 alert em4 alert 2G Connect your equipment to the GPRS 2G network and get alerted by SMS or email Control your application by SMS Receive data reports by SMS or datalogs by email or FTP in.csv (Excel)
KNC-PLC-K506 Series FEATURES DESCRIPTION FEATURES
FEATURES Two High Speed Counters Two Pulse Train Outputs Two Pulse Width Modulation Outputs Inputs 10 Outputs 1 RS232 Port 2 RS485 Ports Supports Modbus RTU Protocol Communicate with up to 32 devices DESCRIPTION
Installation and Operational Instructions for ROBA -switch Type 017._00.2
Manufacturer s Declaration This product is intended for installation in a machine or system, based on the machine directive 2006/42/EC. It is forbidden to start use of the product until the machine or
Installation and Operational Instructions for ROBA -switch Type 017._00.2
OBA -switch Type 017._00.2 Guidelines on the Declaration of Conformity A conformity evaluation has been carried out for the product in terms of the EC Low Voltage Directive 2014/35/ EC and the EMC Directive
ATS01N206QN soft starter for asynchronous motor - ATS01-6 A V KW
Product datasheet Characteristics ATS01N206QN soft starter for asynchronous motor - ATS01-6 A - 380..415V - 1.5..3 KW Complementary Assembly style Function available Supply voltage limits Main Range of
LDW240 Series are single, two or three phase DIN Rail Switching Power Supplies.
LDW240 Series are single, two or three phase DIN Rail Switching Power Supplies. Its compact size, high efficiency, excellent reliability together with easy installation due to pluggable connectors makes
ATS01N222LU soft starter for asynchronous motor - ATS01-22 A V KW
Characteristics soft starter for asynchronous motor - ATS01-22 A - 200..240 V - 4..5.5 KW Main Range of product Altistart 01 Product or component type Product destination Product specific application Device
Custom "Compact" range with display CD20 Custom Part number
Custom "Compact" range with display CD20 Custom Part number 88974051 "Modular" versions designed for Custom application-specific functions (Custom functions) LCD with 4 lines of 18 characters and configurable
SPECIFICATION SWITCHING POWER SUPPLY SINGLE POWER 250W BEST POWER SOLUTIONS, INC. 9F, NO.196-7, SEC.3, TA-TUNG RD SHI CHIH, TAIPEI, TAIWAN, R.O.C.
SPECIFICATION SWITCHING POWER SUPPLY BPS-250S 6-OUTPUT SINGLE POWER 250W BEST POWER SOLUTIONS, INC. 9F, NO.196-7, SEC.3, TA-TUNG RD SHI CHIH, TAIPEI, TAIWAN, R.O.C. Tel: 886-2-8647-1188 Fax: 886-2-8647-3322
"Modular" versions designed for application-specific functions LCD with 4 lines of 18 characters and configurable backlighting
Smart "Compact" range with display CD12 Smart Part number 88974043 "Modular" versions designed for application-specific functions LCD with 4 lines of 18 characters and configurable backlighting Type Input
ATSU01N209LT soft starter for asynchronous motor - ATSU01-9 A V KW
Characteristics soft starter for asynchronous motor - ATSU01-9 A - 200..480V - 1.5..4 KW Product availability : Stock - Normally stocked in distribution facility Price* : 152.00 USD Main Range of product
1715 Redundant I/O System Specifications
Technical Data 1715 Redundant I/O System Specifications System Module Catalog Numbers 1715-AENTR, 1715-IB16D, 1715-OB8DE,1715-IF16, 1715-OF8I Base Unit Catalog Numbers 1715-A2A, 1715-A3IO Termination Assembly
CompactLogix 5370 L3 Control System
CompactLogix 5370 Controllers CompactLogix 5370 L1 Control System CompactLogix 5370 L2 Control System CompactLogix 5370 L3 Control System CompactLogix 5370 controllers provide scalable controller solutions
Installation and Operational Instructions for ROBA -multiswitch Type 019._00.2
Guidelines on the Declaration of Conformity A conformity evaluation has been carried out for the product in terms of the EU Low Voltage Directive 2014/35/ EU and the Electromagnetic Compatibility (EMC)
ATS48D75Y soft starter for asynchronous motor - ATS48-65 A V KW
Characteristics soft starter for asynchronous motor - ATS48-65 A - 208..690 V - 15..55 KW Main Range of product Altistart 48 Product or component type Product destination Product specific application Device
12 Input/12 Output Discrete Embedded TTL I/O Module with Pulse Width Modulation and DeviceLogix
Installation Instructions 12 Input/12 Output Discrete Embedded TTL I/O Module with Pulse Width Modulation and DeviceLogix Cat. No. 1799-D12G12GL Inside... For See page About the Module 1 Important User
Installation and Operating Instructions for Phase Demodulator Type _.2
Guidelines on the Declaration of Conformity A conformity evaluation has been carried out for the product in terms of the EU Low Voltage Directive 2014/35/EU and the Electromagnetic Compatibility (EMC)
PRetrans Table of contents
HART TRANSPARENT REPEATER PRetrans 5106 Table of contents Warnings 16 Safety instructions 17 EC Declaration of Conformity 19 How to demount SYSTEM 5000 20 Application 21 Technical characteristics 21 Mounting
ATV12H037F1 variable speed drive ATV kW hp V - 1ph - with heat sink
Characteristics variable speed drive ATV12-0.37kW - 0.55hp - 100..120V - 1ph - with heat sink Main Range of product Altivar 12 Product or component type Product destination Product specific application
ATV12H018F1 variable speed drive ATV kW hp V - 1ph
Characteristics variable speed drive ATV12-0.18kW - 0.25hp - 100..120V - 1ph Main Range of product Altivar 12 Product or component type Product destination Product specific application Assembly style Component
Output Voltage* (nom.)(adjustable)
Industrial Power Supplies TIB Series, 80 480 W Slim profile, reduced module width High Power Factor up to 99% High efficiency up to 94% True back power immunity Low heat dissipation 150% peak current Automatic
LDC480 Series is a single phase, extremely compact Power Supply with active PFC specially designed for space sensitive and demanding applications.
LDC480 Series is a single phase, extremely compact Power Supply with active PFC specially designed for space sensitive and demanding applications. Its compact size, high efficiency, excellent reliability
ATS01N125FT soft starter for asynchronous motor - ATS01-25 A V KW
Characteristics soft starter for asynchronous motor - ATS01-25 A - 110..480V - 2.2..11 KW Main Range of product Altistart 01 Product or component type Product destination Product specific application Device
ATS01N112FT soft starter for asynchronous motor - ATS01-12 A V KW
Characteristics soft starter for asynchronous motor - ATS01-12 A - 110..480V - 1.5..5.5 KW Main Range of product Altistart 01 Product or component type Product destination Product specific application
08/07/2015
17.5 mm - 1 Relay 8A MUR1 Part number 88827105 Multi-function or mono-function Multi-range Multi-voltage Screw or spring terminals LED status indicator (relay version) Possibility of external load connection
Model Number Structure
Single-phase Voltage Relay CSM DS_E_3_1 Ideal for voltage monitoring for industrial facilities and equipment. Monitor for overvoltages or undervoltages. Manual resetting and automatically resetting supported
ATV12HU22M2. Main. Range of product Altivar 12. Component name Quantity per set Set of 1. Built-in fan. Motor power hp Communication port protocol
Product datasheet Characteristics ATV12HU22M2 Complementary Main Range of product Altivar 12 Product or component type Product destination Product specific application Assembly style Component name Variable
02/11/2015
35 mm - 1 Relay 8A OUR3 Part number 88867103 Multi-function or mono-function Multi-range Multi-voltage Relay output 1 or 2 : 8 A - 250 V (10 A UL) LED status indicator Option of connecting an external
LDW25-24 is a single or two phase AC or DC input DIN Rail Switching Power Supply.
LDW25-24 is a single or two phase AC or DC input DIN Rail Switching Power Supply. Its compact size, high efficiency, excellent reliability together with easy installation due to pluggable connectors makes
SPECIFICATION SWITCHING POWER SUPPLY BPS-300SP/2U 6-OUTPUT WITH ACTIVE PFC FUNCTION SINGLE POWER 300W BEST POWER SOLUTIONS, INC.
SPECIFICATION SWITCHING POWER SUPPLY BPS-300SP/2U 6-OUTPUT WITH ACTIVE PFC FUNCTION SINGLE POWER 300W BEST POWER SOLUTIONS, INC. 2F, NO.196-10, SEC.3, DA-TONG RD., XIZHI DIST., NEW TAIPEI CITY, TAIWAN
Notes: Note1: Efficiency is tested at nominal input and full load at +25 C ambient. Output Voltage 400VAC 400VAC
Features DIN-Rail Description 2 and 3-phase operation Input voltage range: 320 575VAC Output trim range: 22.5 29.5VDC High electrical strength; high reliability Permanent overload and short-circuit protection
ATS01N103FT soft starter for asynchronous motor - ATS01-3 A V KW
Characteristics soft starter for asynchronous motor - ATS01-3 A - 110..480V - 0.55..1.1 KW Main Range of product Altistart 01 Product or component type Product destination Product specific application
IC800SSD Hardware Manual Pub 348R5. for models. A publication of
IC800SSD Hardware Manual Pub 348R5 for models IC800SSD104S1A IC800SSD104RS1A IC800SSD107S1A IC800SSD107RS1A IC800SSD407RS1A IC800SSD216S1A IC800SSD216RS1A IC800SSD420RS1A IC800SSD228S1A IC800SSD228RS1A
Notes: Note1: Efficiency is tested at nominal input and full load at +25 C ambient. Output Voltage 400VAC 320VAC 360VAC 400VAC 400VAC
Features DIN-Rail 2 and 3-phase operation Input voltage range: 320 575VAC Output trim range: 22.5 29.5VDC High electrical strength; high reliability Permanent overload and short-circuit protection Parallel
ATV12HU40M3 variable speed drive ATV12-4kW - 5hp V - 3ph - with heat sink
Characteristics variable speed drive ATV12-4kW - 5hp - 200..240V - 3ph - with heat sink Main Range of product Altivar 12 Product or component type Product destination Product specific application Assembly
Phase-sequence Phase-loss Relay
Phase-sequence Phase-loss Relay K8AB-PH Three-phase Phase-sequence Phase-loss Relay Using Voltage Detection Method Prevents reverse motor rotation due to incorrect wiring. Distinguishes between positive
SPECIFICATION REDUNDANT POWER SUPPLY HOT-SWAPPABLE 370W+370W
SPECIFICATION REDUNDANT POWER SUPPLY HOT-SWAPPABLE BPS-370RDX 6-OUTPUT 370W+370W 1.0 General 1.1 Parameter Specifications 2.0 Input Characteristics 2.1 Input Voltage 2.2 Input Waveform 2.3 Input Frequency
NEW Series STH Output to 75A, 600 Vac High Industrial Performance (HIPpak) Solid-State Relays
FEATURES/BENEFITS Zero-cross models for resistive loads Low zero-cross turn-on voltage Input protection and control LED standard IP20 touch-proof flaps optional Connectors for power wiring and heat sinks
TRC ELECTRONICS, INC
Bauart gepruft Sicherheit egelma ge od o s be wac g www. tuv.com ID 2000000000 SPECIFICATION MODEL DRC-100A DRC-100B OUTPUT NUMBER DC VOLTAGE CH1 13.8V CH2 13.8V CH1 27.6V CH2 27.6V RATED CURRENT CURRENT
Analog Universal Module HART for Zone 2 Series 9468/33
> 8 channels can be adjusted individually as analog inputs or outputs > Intrinsically safe inputs/outputs Ex ia > For 0/4 20 ma + HART signals > Line fault monitoring per channel > Diagnostics based on
DRC-100 series. 100W Single Output with Battery Charger (UPS Function) File Name:DRC-100-SPEC Sicherheit ID
Bauartgepruft Sicherheit egelma ge od o s be wac g www. tuv.com ID 2000000000 SPECIFICATION MODEL OUTPUT INPUT PROTECTION OUTPUT NUMBER DC VOLTAGE LINE REGULATION LOAD REGULATION SETUP, RISE TIME Note.4
Trusted 20 Channel Isolated AI/DI FTA Loop Powered
ICSTT-RM294E-EN-P (PD-T8833) Trusted Trusted 20 Channel Isolated AI/DI FTA Loop Powered Product Overview The Trusted 20 Channel Isolated Analogue Input/Digital Input (AI/DI) Field Termination Assembly
02/11/2015
35 mm - 2 Relays 8A PL2R1 Part number 88867455 Multi-function or mono-function Multi-range Multi-voltage Relay output 1 or 2 : 8 A - 250 V (10 A UL) LED status indicator Option of connecting an external
18V 35V 65V 40A 60A 1.5W 1.2W ms 40ms. 20ms 20ms
Features DIN Rail Description Universal AC Input (85264VAC) Protections: SCP, OVP, OLP, OTP DC OK Indicator LED with Relay Contacts 5% (8W) peak load capacity Builtin active PFC,PF>,95 High effciency up
HVG-65 SERIES 65 Watt LED Power Supply Measures: 7.44 x 4.42 x 1.45
IP65 IP67 Mean Well SPECIFICATION MODEL DC VOLTAGE HVG-65-12 12V HVG-65-15 15V HVG-65- V HVG-65-24 24V HVG-65-30 30V HVG-65-36 36V HVG-65-42 42V HVG-65-48 48V HVG-65-54 54V CONSTANT CURRENT REGION Note.4
MODEL: M2SES SEN TRONIC AG [3] OUTPUT
![MODEL: M2SES SEN TRONIC AG [3] OUTPUT](/thumbs/86/93838653.jpg "MODEL: M2SES SEN TRONIC AG [3] OUTPUT")
Super-mini Signal Conditioners Mini-M Series HIGH/LOW SELECTOR Functions & Features Monitors two DC input signals and transmits an output signal proportional to the higher or lower input CE marking UL
LPS TRC ELECTRONICS, INC
LPS Bauart gepruft Sicherheit egelma ge od o s be wac g www. tuv.com ID 2000000000 SPECIFICATION MODEL DRC-60A DRC-60B OUTPUT NUMBER DC VOLTAGE CH1 13.8V CH2 13.8V CH1 27.6V CH2 27.6V RATED CURRENT CURRENT
DQM601 / DQM SEP 2003 Page Digital Outputs HE550DQM601 / HE559DQM601 24VDC Out, Negative Logic HE559DQM606 24VDC Out, Positive Logic
DQM601 / DQM606 29 SEP 2003 Page 1 16 Digital Outputs HE550DQM601 / HE559DQM601 24VDC Out, Negative Logic HE559DQM606 24VDC Out, Positive Logic SmartStix For electronic information, see www.hornerocs.com.
HLN-40H SERIES 40 Watt LED Power Supply Measures: 6.34 x 2.42 x 1.38
IP64 SPECIFICATION MODEL HLN-40H-12 HLN-40H-15 HLN-40H- HLN-40H-24 HLN-40H-30 HLN-40H-36 HLN-40H-42 HLN-40H-48 HLN-40H-54 DC VOLTAGE 12V 15V V 24V 30V 36V 42V 48V 54V CONSTANT CURRENT REGION Note.4 7.2
50W Constant Current (700mA) Dimming LED Driver
50W Constant Current (700mA) Dimming LED Driver IZC070-050A-9267C-SA Product Overview The IZC070-050A-9267C-SA operate from a 90-305 Vac input range. This unit will provide up to a 700mA of output current
24V 14.4 ~ 24V 20V 12 ~ 20V. 48V 28.8 ~ 48V 3.33A 2.67A 2A 1.67A 1.34A 1.12A 0.96A 0.84A 39.96W 40.05W 40W 40.08W 40.2W 40.32W 40.32W 40.
IP65 IP67 SPECIFICATION MODEL OUTPUT INPUT PROTECTION ENVIRONMENT SAFETY & EMC OTHERS NOTE DC VOLTAGE CONSTANT CURRENT REGION Note.4 7.2 ~12V RATED CURRENT RATED POWER RIPPLE & NOISE (max.) Note.2 150mVp-p
LPS. DRC-60 SERIES 60 Watt Battery Charger Power Supply Measures: 3.94 x 3.54 x 1.57 (866) MEAN WELL
Bauar t gepruft Sicherheit egelma ge od o s be wac g www. tuv.com ID 2000000000 MEAN WELL LPS File Name:DRC-60-SPEC 2014-1122 /mean-well-drc-60-power-supply.html SPECIFICATION MODEL DRC-60A DRC-60B MEAN
HLG-60H-15 HLG-60H-20 HLG-60H-24 HLG-60H-30 HLG-60H-36 HLG-60H-42 HLG-60H-48 HLG-60H-54 DC VOLTAGE CONSTANT CURRENT REGION Note.
IP65 IP67 SPECIFICATION MODEL -15 - -24-30 -36-42 -48-54 DC VOLTAGE CONSTANT CURRENT REGION Note.4 15V 9 ~ 15V V 12 ~ V 24V 14.4 ~ 24V 30V 18 ~ 30V 36V 21.6 ~ 36V 42V 25.2 ~ 42V 48V 28.8 ~ 48V 54V.4 ~
IP65 IP mVp-p 13.5 ~ 17V. 150mVp-p 17 ~ 22V 22 ~ 27V. Can be adjusted by internal potentiometer or through output cable
IP65 IP67 SPECIFICATION MODEL OUTPUT INPUT PROTECTION ENVIRONMENT SAFETY & EMC OTHERS NOTE DC VOLTAGE RATED CURRENT RATED POWER RIPPLE & NOISE (max.) Note.2 150mVp-p VOLTAGE ADJ. RANGE Note.5 10.8 ~ 13.5V
IP65 IP67 42V 5A 4.8A 4A 3.2A 2.65A 2.28A 2A. 150mVp-p. 200mVp-p 27 ~ 33V 22 ~ 27V. Can be adjusted by internal potentiometer or through output cable
IP65 IP67 SPECIFICATION MODEL OUTPUT INPUT PROTECTION ENVIRONMENT SAFETY & EMC OTHERS NOTE DC VOLTAGE RATED CURRENT RATED POWER RIPPLE & NOISE (max.) Note.2 150mVp-p VOLTAGE ADJ. RANGE Note.5 13.5 ~ 17V
1715 Redundant I/O System Specifications
Technical Data 1715 Redundant I/O System Specifications System Module Catalog Numbers 1715-AENTR, 1715-IB16D, 1715-OB8DE,1715-IF16, 1715-OF8I Base Unit Catalog Numbers 1715-A2A, 1715-A3IO Termination Assembly
D.C. BRUSHLESS MOTORS DRIVE. BLD07-IT Service Manual
D.C. BRUSHLESS MOTORS DRIVE BLD07-IT Service Manual INTECNO s.r.l. Via Caduti di Sabbiuno n. 9/E 40011 Anzola Emilia (BO) - Italy tel. 051.19985350 fax 051.19985360 www.intecno-srl.com INDEX Description
IP65 IP mVp-p 13.5 ~ 17V. 150mVp-p 17 ~ 22V 22 ~ 27V 4.65 ~ 9.3A 1.0% 3.9 ~ 7.8A 1.0%
IP65 IP67 SPECIFICATION MODEL OUTPUT INPUT PROTECTION ENVIRONMENT SAFETY & EMC OTHERS NOTE DC VOLTAGE RATED CURRENT RATED POWER RIPPLE & NOISE (max.) Note.2 150mVp-p VOLTAGE ADJ. RANGE Note.5 10.8 ~ 13.5V
MINI MCR-SL-UI-I-LP-NC
2-way isolation amplifier Data sheet 105263_en_02 PHOENIX CONTACT 2013-12-13 1 Description The configurable 2-way isolation amplifiers are used to electrically isolate, convert and filter standard signals.
CB Scheme UL508 UL ATEX II3G
Industrial Power Supplies UL Hazloc Class I, division 2 approval and ATEX certification SEMI F47 compliant for voltage sag immunity Rugged metal case with optional side-mounting Very high efficiency up
High precision measurement system for current and voltage IHC-A/B-RM01/03
Measurement Offset-free and low-noise 16 bit data acquisition system ISA-ASIC Internal sample rate 3,500 Hz Communication Standard RS232- or RS485 interface Advantages Direct measurement on the bus bar
DSR120 Series. xxx Series. 120 Watts. AC-DC Power Supplies. Models & Ratings. Mechanical Details
120 Watts xxx Series Ultra Slim Design - 32 mm 150% Peak Load for 3 seconds Ambient Operation from -25 C to +70 C Full Load at 60 C (24V/48V) High Efficiency - Up to 92% Volt-Free Contact for OK Selectable
MCR-SL-CUC Universal current transducer. Data sheet _en_05. 1 Description
Universal current transducer Data sheet 104059_en_05 PHOENIX CONTACT 2011-03-09 1 Description MCR-SL-CUC-...-I and MCR-SL-CUC-...-U active current transducers convert DC, AC, and distorted currents into
Data Acquisition Modules/ Distributed IO Modules
User Manual Data Acquisition Modules/ Distributed IO Modules Future Design Controls, Inc. 7524 West 98 th Place / P.O. Box 1196 Bridgeview, IL 60455 888.751.5444 - Office: 888.307.8014 - Fax 866.342.5332
ADC5000 SERIES. AC/DC Switch Mode Power Supplies and Rectifiers for Industrial and Telecom Applications. 60W, 125W and 250 W
ADC5000 SERIES AC/DC Switch Mode Power Supplies and Rectifiers for Industrial and Telecom Applications 60W, 125W and 250 W Input voltage 230/115 VAC voltages 12, 24, 36 or 48 VDC Statistical MTBF >3 000
Digital Panel Meter K3TE. Model Number Structure. Model Number Legend. Easy-to-use, Low-cost Digital Panel Meter that Accepts DC Input K3TE
Digital Panel Meter K3TE Easy-to-use, Low-cost Digital Panel Meter that Accepts DC Input Compact DIN-size (96 x 48 (W x H)) body. Mounting thickness of only 3.5 mm required. Highly visible display with
36V 21.6 ~ 36V 5A 5A 4A 3.4A 2.7A 2.3A 1.95A 1.7A 24V 14.4 ~ 24V 20V 12 ~ 20V. 60W 75W 80W 81.6W 81W 82.8W 81.9W 81.6W 150mVp-p.
IP65 IP67 SPECIFICATION MODEL OUTPUT INPUT PROTECTION ENVIRONMENT SAFETY & EMC OTHERS NOTE DC VOLTAGE RATED CURRENT RATED POWER RIPPLE & NOISE (max.) Note.2 150mVp-p CURRENT ADJ. RANGE VOLTAGE TOLERANCE
24V 30V 60W 60W 60W 60W 61.2W 60.9W 62.4W 62.1W
IP64 SPECIFICATION MODEL HLN-H-15 HLN-H- HLN-H-24 HLN-H-30 HLN-H-36 HLN-H-42 HLN-H-48 HLN-H-54 DC VOLTAGE 15V V 24V 30V 36V 42V 48V 54V CONSTANT CURRENT REGION Note.4 9 ~ 15V 12 ~ V 14.4 ~ 24V 18 ~ 30V
E E E E E E E E E E E E IP65 IP67
½ IP65 IP67 series SPECIFICATION MODEL OUTPUT INPUT PROTECTION ENVIRONMENT SAFETY & EMC OTHERS NOTE DC VOLTAGE RATED CURRENT RATED POWER RIPPLE & NOISE (max.) Note.2 150mVp-p VOLTAGE ADJ. RANGE Note.5
Safety Precautions. Copyright / Trademarks
Safety Precautions Observe the following notices to ensure personal safety or to prevent accidents. To ensure that you use this product correctly, read this User s Manual thoroughly before use. Make sure
DIN 22.5/17.5 Size Lineup of A Wide Range of Measuring and Monitoring Relays. Model Number Structure
New Product News Measuring & Monitoring Relays K8AK/K8DS Series DIN 22.5/17.5 Size Lineup of A Wide Range of Measuring and Monitoring Relays Compact 22.5 mm and 17.5 mm housings Resistant to high-frequency
IP65 IP67. Can be adjusted by internal potentiometer A type only
IP65 IP67 SPECIFICATION MODEL HVGC-65-350 HVGC-65-500 HVGC-65-700 HVGC-65-1050 RATED CURRENT 350mA 500mA 700mA 1050mA CONSTANT CURRENT REGION Note.4 112 ~ 186V 78 ~ 130V 56 ~ 93V 37 ~ 62V CURRENT ACCURACY
24V 30V 90% 90% 90.5% 90.5% COLD START 55A(twidth=265μs measured at 50% Ipeak) at 230VAC
IP65 IP67 MEAN WELL SPECIFICATION MODEL DC VOLTAGE -15 15V - V -24 24V -30 30V -36 36V -42 42V -48 48V -54 54V CONSTANT CURRENT REGION Note.4 9 ~ 15V 12 ~ V 14.4 ~ 24V 18 ~ 30V 21.6 ~ 36V 25.2 ~ 42V 28.8
IP65 IP mVp-p. 150mVp-p 17 ~ 22V 22 ~ 27V. Can be adjusted by internal potentiometer or through output cable 5 ~ 10A 3 ~ 6A 1.0% 2.5 ~ 5A 1.
IP65 IP67 SPECIFICATION MODEL OUTPUT INPUT PROTECTION ENVIRONMENT SAFETY & EMC OTHERS NOTE DC VOLTAGE RATED CURRENT RATED POWER RIPPLE & NOISE (max.) Note.2 150mVp-p VOLTAGE ADJ. RANGE Note.5 10.8 ~ 13.5V