Item Number Description Price Pen style voltage detector light $ Min/Max recording Current 10A AC/DC Resistance 50M Frequency 100 K Hz.

Transcription

1 TEST EQUIPMENT Fluke Senses the steady state electrostatic field produced by a voltage through insulation without requiring contact to the bare conductor. Upon detection tip glows and beeper sounds High density red LED light Includes 2 AAA batteries 3115 Includes test leads 3115 Pen style voltage detector light $21.95 Wide 1000 Max Voltage True RMS for precise measurement of non linear signals Large easy to read display Up to a.09% basic DC accuracy Backlight for work in dimly lit areas Min/Max recording Current 10A AC/DC Resistance 50M Frequency 100 K Hz. Limited Manufacturer Lifetime Warranty 179 Includes test leads 179 True RMS digital multimeters, with built in Thermometer $ Large digit display with two level bright backlight Built in thermometer True RMS AC voltage and current for accurate measurements of non linear signals.05% DC accuracy 4-1/2 digit mode for precise measurements Measure up to 1000V AC and DC Limited Manufacturer Lifetime Warranty Measure up to 10A, 20A, for up to 30 seconds Frequency to 200 khz. and % duty cycle Resistance 50m AC/DC Min/Max Recording 87-5 Includes test leads 87-5 Industrial digital multimeter $

2 TEST EQUIPMENT Fluke VoltAlert technology for non contact voltage detection AutoVolt automatic AC/DC voltage selection LoZ helps prevent false reading due to ghost voltage True-RMS for accurate measurements on non linear loads Measures 10 A(20 A overload) for 30 seconds Cat III 600 V safety rated Includes holster, manual, and 9V battery Min/Max Recording 3 Year Manufacturer Warranty FLUKE 117 Includes test leads FLUKE 117 Electrician s multimeter with non contact voltage and true RMS $ True RMS AC voltage and current for accurate measurements on non-linear signals Integrated low pass filter and state of the art signal processing allows for use in noisy electrical environments while providing stable readings. AC and DC current via jaw: 600 A Proprietary inrush measurement technology to filter out noise and capture motor starting current exactly as the circuit protection sees it. Max measurable conductor diameter.13" or 34 mm 500 Hz. 3 year manufacturer warranty FLUKE-375 Includes test leads & Carrying Case FLUKE -375 True RMS AC/DC clamp meter $ True RMS AC voltage and current for accurate measurements on non-linear signals Built in thermometer Resistance, continuity, and diode test modes Low power wireless technology allows display to be carried up to 10 meters (33 ft.) away from the point of measurement for added flexibility. Frequency 5Hz. to 50kHz. resolution to.01hz. Radio transmitter automatically turns off when the display is connected to the meter Min/Max and Average recording to capture variations automatically Easy to ready display with large digits and bright backlight. DC Voltage range.1mv to 1000V accuracy of.25% AC Voltage.1mV to 1000V accuracy to 1.0% and DC Current 1mA to 10A accuracy to 1% and AC Current 1mA to 10A accuracy to 1.5% Safety rating Cat IV 600V, CAT III 1000V 3 Year Manufacturer Warranty FLUKE 233 Includes test leads FLUKE 233 DMM Meter with remote display $

3 TEST EQUIPMENT Fluke (continued) Battery powered Hall-effect probe measures 1A to 400A AC/DC 1 mv/ Amp output guarantees easy ready on your meter Takes accurate current reading without breaking the circuit Maximum conductor Ø 32 mm-1.18in Cat III 600 V safety rating 1 Year Manufacturer Warranty I410 Includes test leads I410 Accessory AC/DC Current Clamp $ Fluke Modular Clips and Probes Slide on style for test probes Jaws open to 8 mm For use with TL71 & TL75 test leads and probe sets CAT III 1000 V, 10 A; CAT IV 600V, 10 A AC72 AC72 Alligator Clips $14.95 Multi purpose tooth pattern grips anything from fine gauge wire to a 3/4" nut Nickel plated steel jaws CAT III 1000 V, CAT IV 600 V, 10 A AC285 AC285 SureGrip Alligator Clips $

4 SUBHEAD TEST EQUIPMENT Fluke Modular Clips and Probes (continued) Profile narrows to.22" tip Hook opening.20" at front,.08" at base CAT III 1000 V, CAT IV 600 V, 3 A AC280 AC280 SureGrip Hook Clips $ Insulated, nickel plated jaws grip objects up to 3/8" Blunt tip grabs round screw heads CAT III 1000 V, CAT IV 600 V, 10 A AC220 AC220 SureGrip Alligator Clips $37.45 Fluke Test Leads Extremely hard alloy tips resist wear Distinctive comfort grip probes CAT III 1000 V, 10 A; CAT IV 600 V, 10 A TL75 Hard Point Test Lead Set $20.95 TL75 Recommended for use with AC220, AC280, and AC283 test clips Superior strain relief CAT III 1000 V, 10 A; CAT IV 600 V, 10 A TL222 SureGrip Silicone Insulated Test Leads $24.95 TL

5 TEST EQUIPMENT SUBHEAD Fluke Test Leads (continued) Retractable insulated sharp probe tip CAT II 300 V, 2 A TL40 TL40 Retractable Probe Assembly $39.95 Large, solid copper alligator clips with.5" opening Flexible silicone insulated lead are heat and cold resistant CAT I 30 V, 10 A TL28 TL28 Automotive Test Lead Set $44.95 DMM test leads (red, black) with safety shrouded, standard diameter banana plugs Right angle connector on one end and straight connector on the other 1.5 mm silicone-insulated wire resists heat & cold CAT III 1000 V, 10 A; CAT IV 600 V, 10 A Superior strain relief TL224 TL224 SureGrip Insulated Test Leads $24.95 TPAK Accessories TPAK Magnetic meter hanging solution $39.95 C25 Soft zippered carrying case ( 8.5 x 4.9 x 2.5 in.) $

6 SUBHEAD TEST EQUIPMENT Tripplett Fox and Hound Tone Generator includes overload protection (120 VAC Line), Overload Warning Beeper, High Output Tracer Tone, Selectable tracer tones, Red/Green telephone line polarity LEDS (also indicates AC/RING Signal) Hound 3 Probe Inductive Tracer features: streamline design for better access in hard to reach areas, bandpass filter suppresses 60 Hz. and hi-frequency noise, includes conductive duck bill tip and metal tips, LED indicator light gets brighter as the signal gets stronger *Note: The Fox & Hound Series is not intended for use on powered wires or cables. All wires or cables must be non-powered, non-grounded, and non-connected. Multimeter Large backlit display with bar graph Cat IV safety rating UL Listed 10A AC/DC current Lead storage and rubber molding for added protection Plug Bug For use on 110 or 125 VAC receptacles Detects common wiring problems in standard and GFCI outlets GFCI Test in Progress LED indicator TRP-3399 MM Fox and Hound TRIP-3399 Fox and Hound kit includes: Fox 2 Deluxe Tone Generator with True Trace and Hound 3 Probe Inductive Tracer $ Multimeter MM2000 True RMS low Impedence Electrician s/ HVAC Multimeter $ Plug Bug 9610 Plug-Bug2 GFCI / Polarity receptacle tester $

7 TEST EQUIPMENT SUBHEAD Inspection Cameras Tripplett 2.4" TFT LCD Screen 72" removable/replaceable snake camera; can be bent to access hidden locations Image can rotate 180 degree Camera 7/16" in diameter with 2 adjustable white LED for illumination Camera is waterproof Klein Video/audio & photo recording Bright LED work light IP67 gooseneck camera Screen rotation TV-out jack and SD card slot File playback Kit includes: Main Unit, 17mm gooseneck camera, 1850 Series 3.7V 2000mAh Rechargeable Li-Ion Battery, mirror camera attachment, magnet camera attachment, USB power adapter/charger, USB data/charger cable, RCA composite AIV to 3.5mm mini AIC cable, quick start guide, software instruction manual CD rom, and carrying case COBRA CAM ET500 Tripplett COBRACAM Portable Inspection Camera $ Klein ET500 Video Borescope $ Blue Seas Systems Multimeter True RMS AC measurement is accurate for normal sine wave and modified sine wave inverter output Simplify operation with Auto Range, selects the best range that fits the data Compact size for comfortable one hand operation, portability and access to confined areas. AC Amps-600 AC Volts-600 DC Amps-400 DC Volts-600 MINI CLAMP MULTIMETER Item Number AC Amps AC Volts DC Amps DC Volts Price Multimeter $

8 SUBHEAD TEST EQUIPMENT Infrared Thermometer Klein K type thermocouple input F/C buttons 12:1 Spot ratio Dual laser targeting Max/Min/Avg./Diff Backlit Display Includes: Case, batteries, and K-type thermocouple Jewell 12:1 measurement ratio Laser pinpoints measurement area without making contact White, backlit LCD with selectable Fahrenheit or Celsius reading Compact, gun shaped case with SilkGrip for non slip comfort 1.5% accuracy.1f Resolution.95 Fixed Emissivity IR-2000 PT12 Item Number Range Price Klein IR F(-60 C) to 1022 F(550 C) $ Jewell Instruments PT12-26ºF (-32ºC) to 572ºF (300ºC) $85.00 Hull Testing Meters For optimum protection Steel Hulls.85, Aluminum Hulls.95, and Bronze fittings on Wood Hulls.55 Meter: 0 to 1.5V full scale 1% full scale accuracy Impendence 20,000 ohms to 30,000 ohms total Reference cell is silver-silver chloride type silver screen with deposited silver chloride. Half cell insulated cable length 75ft Portable Hull Pontential Meter $1,

9 TEST EQUIPMENT HEAT TOOLS Hull Testing Meters (continued) Determines effectiveness of Cathodic Protection Checks Bonding System Integrity Checks for AC shoreline interference Troubleshoots AC and DC electrical systems Kit Includes: Fluke model 110 digital multimeter with test leads, Zinc reference probe with 20' of test lead wire, 25' test lead extension, hardened steel test probe. 902TI 902TI Corrosion Test Instrument Kit $ Heat Guns PH-1100 Proheat Heat Gun: compact, lightweight, easy to use. Two heats: 430 F(221 C) & 840 F(449 C) 15 CFM air flow Built in Stand HG-751B Master Heat Guns: professional, heavy duty, industrial quality, multiple use heat gun High temperature rating 1000 F(540 C) 23 CFM and 3000 FPM Adjustable non slip stand Sturdy Die Cast Housing PH-1100 HG-751B Item Number Volt Hz. Amps Watts Price PH & & 1300 $ HG-751B $

10 HEAT TOOLS Torches and Irons Turbo Lite II Piezo Waterproof/ Windproof Ignition System Twist flame adjustment Refillable translucent fuel tank Pinpoint flame of 2400 F(1315 C) Industrial Torch Self igniting Piezo electric ignition Self contained, metal fuel tank Adjustable blue flame, temperature up to 2500 ºF(1300 ºC) Safety lock prevents unintentional ignition for storage Approximate run time 30 minutes Power Torch Brass and Steel construction Dual gas and air flame controls Up to 2500 F(1300 C) Torch output Safety Lock feature to prevent accidents Removable base for hands free operation in both vertical and horizontal position Approximately run time up to 220 minutes on one tank Soldering Irons Kit contains: unit, solder tip, heat tip, shrink attachment, spanner and open end wrench, sponge and stand packed in metal storage carrying case Built in fuel filter for consistent fuel ignition Built in window indicates fuel level 10.3" (260mm) long Operating time 120 minutes on 1 fl. oz tank Solder tip temperature: 482ºF(250ºC) to 932ºF(500ºC) Heat tip temperature: 1202ºF(650C) GT UT-100SIK Item Number Description Dimensions in " (mm) LxWxH Price Turbo Lite II 1.4(35) x.8(20) x 2.8(2.8) $21.80 GT-70 General Industrial Torch 6.5(165.1) x 5(127) x 1.8(45.72) $ Butane Power Torch 3.9(100) x 1.4(36) x 5.4(138) $ UT-100SIK Ultratorch professional soldering tool kit $

11 HEAT TOOLS Iron Accessories Iron tips feature leading edge combustion chamber exhaust port design Copper based iron tips are manufactured using patented process which produces a uniform iron and chrome plating thickness All tips are pre-tinned mm diameter chisel soldering tip (standard) $ mm diameter tapered needle soldering tip $ mm diameter 35 spade soldering tip $ O.D/ 4.9 I.D mm heat tip (standard) $ Hot knife tip $21.13 Torch Accessories Triple refined formula reduces clogging of filters Special vapor pressure promotes consistent ignition Contains no CFC s Recommended refill for all Ultratorch & Master butane powered products BUTANE Both sizes include canister with universal tip adapter Butane Ultratane butane 5-1/8 oz. $ Ultratane butane 15/16 oz. $5.85 Burners 80-04U Burner for UT 100 & UT100SI $

12 INSULATED HAND TOOLS CRIMPERS Klein Screwdrivers 1000V Rated Durable, two layer, molded insulation to meet or exceed all ASTM and IEC standards for insulated tools Cushion grip handle for greater torque and comfort for easy access Custom US made tool steel Cutting Pliers Exceeds the IEC and ASTM F1505 standards, for insulated tools Clearly marked for 1000 Volt Two Layers of insulation provides protection against electrical shock Thick, tough high dielectric white inner coating Flame retardant, impact resistant, outer coating Rivet is closer to the edge for 36% greater cutting power Integral guards help prevent hand contact with conductive parts INS INS D INS Item Number Tip Type Length In " Hand Style Price Screwdrivers INS #2 Phillips 7 Round Shank $ INS 5/16" Cabinet 7 Round Shank $30.92 Item Number Jaw Width In " Jaw Length In " Overall Length In " Price Cutting Pliers D INS 1-3/16 13/16 8-1/4 $90.50 Terminal Interchangeable dies change quickly and easily with screwdriver Built in locator Cushioned comfort grip handles Crimp Size 22AWG-18AWG (Insulated) Crimpmaster Insulated Terminal Crimp $ Crimp size 22 AWG -10 AWG For use with insulated terminals and splices Pro-crimper $

13 CRIMPERS SUBHEAD Terminal (Continued) Fits wire sizes 8 AWG to 4/0 AWG ROTO CRIMP hand tool for uninsulated terminals and splices Large rotocrimp $1, Two rotating crimping dies held together with spring loaded indexing pins Used to apply SOLISTRAND and CABLE MARKER terminals to stranded copper wire. Do not use these tools on aircraft applications or on aluminum wire terminations Can us on wire sizes 8AWG to 1/ Bantam rotocrimp $ AMP open barrel service tool for stamped contacts and D Sub contacts Includes opening for crimping insulated terminals and cutters for machine screws Crimps Double-D high density miniature contacts Crimper Service tool $

14 SUBHEAD CRIMPERS Terminal (Continued) 4 Crimp nests 8AWG, AWG, AWG, and AWG Mating Mechanism prevents the jaws from slipping or misalignment Long handles make it easier to crimp Easy to use and understand release mechanism Ergonomic design to initiate the crimp process T-R-50 T-R-50 Terminal crimper, 22-8 AWG range $60.05 Crimping die marked for insulated and non-insulated solderless terminals and connectors. Tapered nose design for working in confined spaces. Specially hardened wire cutter in nose. Hot-riveted joint for smooth action and no handle wobble Crimps size: AWG Overall length 9-3/4" (248 mm) Crimping/Cutting tool Non Insulated/ Insulated Terminals $39.42 Designed for crimping non-insulated solderless terminals and connectors. Specially hardened wire cutter in nose. Tapered nose for working in confined spaces. Plastic dipped cushioned handles for comfort. Crimps AWG Overall length 9-3/4" (248mm) Crimping/Cutting Tool Non Insulated Terminals $40.72 Ferrule Crimping tool with ratchet mechanism Insulated and uninsulated ferrules: 22AWG to 10 AWG Twin wire ferrules: 2 x 22AWG to 2 x 14AWG FD2410N FD2410N Trapezoidal Ferrule Crimper $

15 SUBHEAD CRIMPERS SUBHEAD CUTTERS Ferrule (continued) Crimping tool with ratcheting mechanism Insulated and uninsulated ferrules: 26AWG to 10AWG Twin wire ferrules: 2 x 22AWG to 2 x 14AWG FD2810SQ FD2810SQ Square Ferrule Crimper $ Deutsch Crimps a wide range of contact sizes with no need to change out dies or locators. Provides symmetrical four indent crimp. Compact and easy to use for field service. HDT HDT Hand crimping tool, for Deutsch connectors $ Cable Shear type hook jaws grab and hold cable while shear cutting action makes clean cuts. Beveled tips for positive mating. Hinge bolt with pin set nut for proper blade tension 350 copper, 350 aluminum MCM cable cutting capacity. 16-3/4" (425mm) Utility cable cutter $

16 SUBHEAD CUTTERS Cable (continued) Precise, one hand shearing action cuts 24 AWG copper, aluminum multi strand cable and wire. Special shear angle cuts cleanly without compression to cable geometry for telecom work. Heat treated high carbon steel shearing edges for long life. Not designed for cutting steel or ACSR Compact cable cutter $51.44 Cleanly cuts copper up to 400 MCM, as as aluminum and multi conductor cables up to 600 MCM. Unique ratchet action holds cable tight and allows rapid, straight cuts with minimum effort. Hold action spring speeds cutting action. Not designed for cutting steel or ACSR Ratchet cable cutter $ Cuts up to 4/0 aluminum AWG (no ACSR), 2/0 AWG soft copper and 100-pair 24 AWG communications cable. High leverage for greater cutting power. Precision, one hand shearing action. Overall length: 9-9/16"(243mm) Not designed for cutting steel or ACSR J63050 J63050 High leverage cutting pliers standard $49.46 Pliers Induction hardened cutting knives for long life. Hot riveted joint ensures smooth action and no handle wobble. Short jaws and beveled cutting edges permit close cutting of wire Overall length: 6-1/8"(156mm), Jaw length: 13/16"(21mm) Semi flush cutting knives D202-6 D202-6 Standard diagonal, with tapered nose $

17 CUTTERS Pliers (continued) Sharp pointed nose for precise tip cutting and trimming Spring loaded for self-opening action Jaw length: 11/16, jaw width 9/16 Overall length: 5-1/16 Semi flush cutting knives Plastic dipped handle D209-5C D209-5C 5" Electronics midget diagonal cutting pliers $37.26 Precisely cuts injection mold sprues, gates, and other plastics. Adjustable 1/16" hollow head screw keeps knife edge from damaging each other (not for use on metal) Spring loaded self opening action Overall length: 7-11/16"(195mm) Jaw length: 1"(25mm) Flush cutting knives Great for Ty Wraps D227-7C D227-7C Plastic cutting pliers $62.88 Rivet is closer to the cutting edge for 36% greater cutting and gripping power than other plier designs. Short jaws and beveled cutting edges permit close cutting of wire. Induction hardened cutting knives for long life. Hot riveted joint ensures smooth action and no handle wobble. Overall length 8-1/8"(206mm), Jaw length: 13/16"(21mm) J J High leverage diagonal cutting pliers $51.32 Angled head design for easy work in confined spaces. High leverage design. Rivet is closer to the cutting edge for 36% greater cutting and gripping power. Short jaws and beveled cutting edge permit close cutting of wire. Induction hardened cutting knives. Hot riveted joint ensures smooth action and no handle wobble. Overall length: 8-1/8"(206mm), Jaw length: 13/16"(21mm). J HDT J High leverage diagonal cutting pliers with angled head $

18 SUBHEAD STRIPPERS Strippers Wire looping and bending holes. Precision ground stripping holes. Black oxide finish resists corrosion. Easy to read wire gauge marking on both sides. Do not use for cutting steel wire or bolts. Overall length: 6-1/4"(159mm) Strips and cuts 8-18 AWG solid wire Klein Standard Wire Stripper/Cutter $18.36 Precision shear type blades for clean cuts on solid and stranded copper wire. Easy to read markings on both sides. Precision ground stripping holes. Screw shearing holes. Overall length: 7-1/8"(181mm) Can cut wire AWG solid & AWG stranded Klein Kurve Wire Stripper/Cutter $26.00 Form ground hardened knife type blades. Built in wire cutter & wire looping holes. Laser etched wire gauge markings. Corrosion resistant, black oxide finish. Can strip AWG solid wire & AWG stranded wire T Stripper Wire Stripper $14.66 Wire gripper holds wire centered in stripping hole. Cleanly strips wire up to full 7/8" (.22mm) Eliminates nicking, cutting, and fraying of commercial wire. Can strip AWG Stripmaster Wire Stripper $

19 EXTRACTION SUBHEAD MULTI SUBHEAD TOOLS Extraction Tools For use with Deutsch Terminals and Devices DEUTSCH Deutsch Removal tool size 20 red $ Removal tool size 14 green $ Removal tool size 16 blue $ Removal tool size 8 green $ Removal tool size 4 white $ Removal tool size 12 yellow $4.26 Multi Tools Crimp AWG insulated and non insulated terminals and coaxial connectors. Cut and strip 8-22 AWG solid and AWG stranded wire. Cut and rethread 4-40, 5-40, 6-32,8-32, 10-24, screws. Stainless steel blade resists corrosion and nicking. Precision ground plier nose Stainless Steel Cut/Strip/Crimp Tool $

20 SUBHEAD MULTI TOOLS SUBHEAD CABLE TIE Multi Tools (Continued) Two wire cutters-one at tip a second one halfway back near stripping holes. Cleanly shears bolts size: 4-40, 6-32, 8-32, 10-24, Crimping dies color coded for easy identification. Crimps 7-8 mm insulated and non-insulated terminals, lugs, and splices. Pivot nut adjusts tension. Wire cutter in nose and below pivot. Strips and cuts AWG stranded & 8-22 AWG solid. Overall length: 8-1/2"(216mm) KL Klein Multi Purpose Electrician s Tool $32.86 Cable Tie Tools Consistent, positive tension. Flush cut-off leaves no projections to damage nearby wires or components. FD600A FD600A Standard Economy Model $38.00 Used with standard, light-heavy, heavy and extra-heavy cross section Pan-Steel type MLT ties, type MLTC/MLTFC coated ties, and type MLTDH double wrapped ties. Cable tie side entry for immediate positioning of tie. One hand operation, lightweight. Tool tension is controlled by installer, twist action cutters. Rugged, lightweight, easy to operate pliers type tool. ST2MT ST2MT Stainless Steel Model $

21 SCREWDRIVERS SUBHEAD Klein Patented Tip-Indent quickly identifies the type of screwdriver and screwdriver tip orientation. Premium chrome plated. Internal flanges inside handle provide solid, twist resistant blade anchor. Integrated screwdriver/nut driver shaft holds 8 popular tips and converts to 3 nut driver sizes. Interchangeable blade for quick and easy switch out. Industrial strength, heat tread bits in-1 Screwdriver/Nut Driver $23.00 General purpose selection of the most frequently used screwdrivers. Set includes: three cabinet tip, two phillips tip, and two keystone tip styles with case piece cushion grip set $ Patented Tip-Indent quickly identifies the type of screwdriver and tip orientation. Precision tip for an exact fit. Premium chrome plated shafts for corrosion resistance. Set includes Three cabinet sizes, and One Phillips size piece mini cushion grip set $32.06 Phoenix Also suitable for use as a screwdriver: Phillips.6 x 3.5 x 100 mm HxWxL Two component grip with non slip. SZF-1 SZF-1 Acuation tool for ST terminal blocks $

22 SUBHEAD SAWS AND BITS Hole Saw Kits Includes most frequently used sizes and an arbor extension for hard to reach spots All components are packed in a rust-proof, molded plastic carrying case Set contains: Hole Saws: 3/4" thru 2-1/2" (1/8" to 1/4" increments) Arbors: 1/4" & 7/16" Arbor Extender: 12" Journeyman s 13 piece set $ Unibit Step-Drill Bits Single fluted design eliminates skidding and makes for easier resharpening. Anti skid tip eliminates the need for center punching or pilot hold drilling for most sizes Drill multiple size holes in thin sections of metal, plastic, and wood using a single bit. Laser etched hole sizes are easy to read and permanent UNIBITS Item Number No. of hole Size Range Pilot Hole Required Electric Drill Size Depth Penetration Price sizes per bit (Hole Diameter in ") (per step in ") (in ") * No of hole sizes per bit in inch increments in 1/32" 1/8-1/2 no 1/4" and larger 1/8 $ in 1/16" 9/16-1 yes, 1/2" larger 1/2" and larger 1/8 $ in 1/16" 1/4-3/4 no 3/8" and larger 1/8 $ in 1/16" 13/16-1-3/8 yes, 3/4" or larger 1/2" and larger 1/8 $ in 1/16" 3/16-1/2 no 1/4" and larger 3/8 $

23 TOOL SUBHEAD BAGS Small Storage B 5139 Canvas zipper bag, 12-1/2" length $ B Ballistic nylon zipper bag, 12-1/2" length $13.14 Large Storage Electrician s Bag Tough durable molded bottom protects from the elements 1680d ballistic weave for durability includes removable pockets for easy access Back Pack Wide opening fits power drills, meters, flashlights, etc. Tough durable molded bottom protects from the elements Large front pocket easily fits fish tapes BP Item Number Exterior Pockets Interior Pockets Dimensions in "(mm) LxWxH Price Tradesman Pro Electrician s Bag (482.6) x 6.5(165.1) x 16(406.6) $ (444.5) x 10(254) x 14(355.6) $ Tradesman Pro Backpack BP (355.6) x 7(177.8) x 18(457.2) $