TEST REPORT COMMISSION REGULATION (EU)

Transcription

1 Test Report issued under the responsibility of: SGS-CSTC TEST REORT COMMISSION REGULATION (EU) No 1194/2012 of 12 December 2012 implementing Directive 2009/125/EC of the European arliament and of the Council with regard to ecodesign requirements for directional lamps, light emitting diode lamps and related equipment Report Reference No.... : Tested by (name + signature)... : Hugh Cao Approved by (name + signature)... : Karen Xie GZES Date of issue... : Total number of pages... : Testing Laboratory... : SGS-CSTC Standards Technical Services Co., Ltd. - E&E Lab Guangzhou Address... : 198 Kezhu Road, Scientech ark, Guangzhou Economic & Technology Development District, Guangzhou, Guangdong, China Applicant s name... : Dongguan City Tianhua hotoelectric Technology Co., Ltd. Address... : 2 nd Road, Jinqianling Industrial Zone, Jitigang Village, Huangjiang Town, Dongguan, Guangdong, China Manufacturer s name... : Dongguan City Tianhua hotoelectric Technology Co., Ltd. Address... : 2 nd Road, Jinqianling Industrial Zone, Jitigang Village, Huangjiang Town, Dongguan, Guangdong, China Test specification: Standard... : COMMISSION REGULATION (EU) No 1194/2012 Test procedure... : Er IM test Report Stage... : stage 1 stage 2 stage 3 Non-standard test method..: None Test Report Form No.... : _C Test Report Form(s) Originator... : SGS-CSTC Master TRF... : SGS-CSTC Standards Technical Services Co., Ltd. (SGS-CSTC), Guangzhou,. R. China. All rights reserved. This publication may be produced in whole or in part for non-commercial purposes as long as SGS-CSTC is acknowledged as copyright owner and source of the material. SGS-CSTC takes no responsibility for and will not assume liability for damages resulting from the reader s interpretation of the reproduced material due to its placement and context

2 age 2 of 24 Report No.: GZES Test item description... : Trade Mark... : Factory... : Model/Type reference... : Ratings... : Standard... : LED Touch Lamp (LED module) Dongguan City Tianhua hotoelectric Technology Co., Ltd. 2 nd Road, Jinqianling Industrial Zone, Jitigang Village, Huangjiang Town, Dongguan, Guangdong, China EH1622 Incandescent light bulbs EN DC 12 V; 550 ma; 5 W LED; 330 lm; h; Class III CIE 84 L2(A)005 CIE S 010 Halogen incandescent light bulbs EN CIE 84 L2(A)005 CIE S 010 Compact fluorescent lamps with integrated control gear EN at present 34A/ 1701/CDV CIE 84 L2(A)005 EN High intensity discharge lamps EN CIE 84 L2(A)005 EN EN Light emitting diode lamps EN CIE 84 L2(A)005 EN Light emitting diode modules IEC at present 34A/ 1659/CDV CIE 15 CIE 63 IEC/TR CIE 15 CIE 63 IEC/TR CIE 15 CIE 13.3 CIE 63 IEC/TR EN at present 34A/ 1624/CD CIE 15 CIE 13.3 CIE 63 IEC/TR pren CIE 63 EN CIE 63 EN L2(A)005 pren lighting transformers (halogen and LED) IEC , at present 34C/1019/CDV Fluorescent lamp controlgear EN replacing EN High intensity discharge lamp controlgear IEC , at present 34C/1016/CDV

3 age 3 of 24 Report No.: GZES Summary of testing: The sample(s) tested complies with the requirements of COMMISSION REGULATION (EU) No 1194/2012. The sample(s) also tested complies with the requirements of stage 6 of COMMISSION REGULATION (EC) No 244/ (EC) No 859/2009 for non-directional lamp. These tests were conducted by test lab that fulfils the requirements of standard ISO/IEC When determining the test conclusion, the Measurement Uncertainty of test has been considered. LED driver YHGD (input 100 V V; 50 Hz / 60 Hz; output 550 ma; 12 V DC; ta 35 C; tc 60 C) used for all tests. The LED module was test independently to the luminaire, during all tests luminaire keeping the temperature of tc point of LED module between 75 ºC 80 ºC. Copy of marking plate Rating label: Free access websites:

4 age 4 of 24 Report No.: GZES ackaging:

5 age 5 of 24 Report No.: GZES Test item particulars... : Lamp cap... : Lamp type... : CFL / LED / Mains-voltage filament lamps / other filament lamps / High-intensity discharge lamps: / other lamps: Bulb type... : Non-directional Mass of the equipment... : Commission received from... Dongguan City Tianhua hotoelectric Technology Co., Ltd. Date... : ossible test case verdicts: - test case does not apply to the test object... : - test object does meet the requirement... : (ass) - test object does not meet the requirement... : F (Fail) Testing... : Date of receipt of test item... : Date (s) of performance of tests... : to General remarks: The test results presented in this report relate only to the object tested. This report shall not be reproduced, except in full, without the written approval of the Issuing testing laboratory. "(see Enclosure #)" refers to additional information appended to the report. "(see appended table)" refers to a table appended to the report. This document is issued by the Company subject to its General Conditions of Service, available on request or accessible at and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company s findings at the time of its intervention only and within the limits of Client s instructions, if any. The Company s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only. Throughout this report a comma (point) is used as the decimal separator. General product information: Non-directional LED modules incorporated in class III table luminaires.

6 age 6 of 24 Report No.: GZES Clause Requirement + Test Result - Remark Verdict ANNEX I roduct information requirements for special purpose products 1. If the chromaticity coordinates of a lamp always fall within the following range: x < 0,270 or x > 0,530 y < - 2,3172x 2 + 2,3653x 0,2199 or y > - 2,3172x 2 + 2,3653x 0,1595 x: y: The chromaticity coordinates shall be stated in the technical documentation file, which shall indicate that these coordinates make them a special purpose product. 2. For all special purpose products, the intended purpose shall be stated in all forms of product information, together with the warning that they are not intended for use in other applications. The technical documentation file shall list the technical parameters that make the product design specific for the stated intended purpose. If needed, the parameters shall be listed in such a way as to avoid disclosing commercially sensitive information linked to the manufacturer s intellectual property rights. If the product is placed on the market in a packaging containing to be visibly displayed to the end-user prior to purchase, the following information shall be clearly and prominently indicated on the packaging and in all other forms of product information: (a) the intended purpose; and (b) that it is not suitable for household room illumination. ANNEX III Ecodesign requirements 1 ENERGY EFFICIENCY REQUIREMENTS 1.1 Energy efficiency requirements for directional lamps Table 1 Lamps operating on external halogen lamp control gear Lamps operating on external LED lamp control gear Fluorescent lamps of 16 mm diameter (T5 lamps) and 4- pin single capped fluorescent lamps operating on external fluorescent lamp control gear Other lamps operating on external fluorescent lamp control gear Lamps operating on external high-intensity discharge lamp control gear

7 age 7 of 24 Report No.: GZES Clause Requirement + Test Result - Remark Verdict Compact fluorescent lamps with colour rendering index 90 Lamps with anti-glare shield Table 2 The maximum EEI of directional lamps (See Annex 1) Stage 3 For mains-voltage filament lamps shall apply only if no later than 30 September 2015, evidence is produced by the Commission through a detailed market assessment and communicated to the Consultation Forum that there are mainsvoltage lamps on the market that are: compliant with the maximum EEI requirement in stage 3; affordable in terms of not entailing excessive costs for the majority of end-users; broadly equivalent in terms of consumerrelevant functionality parameters to mainsvoltage filament lamps available on the date of entry into force of this Regulation, including in terms of luminous fluxes spanning the full range of reference luminous fluxes listed in Table 6; Compatible with equipment designed for installation between the mains and filament lamps available on the date of entry into force of this Regulation according to state-of-the-art requirements for compatibility. 1.2 Energy efficiency requirements for lamp control gear Stage 2 Stage 2 Stage 2 Stage 3 Stage 3 Stage 3 The no-load power of a lamp control gear intended for use between the mains and the switch for turning the lamp load on/off shall not exceed 1,0 W..: For lamp control gear with output power () over 250 W, the no-load power limits shall be multiplied by /250 W : The efficiency of a halogen lamp control gear shall be at least 0,91 at 100 % load : The no-load power of a lamp control gear intended for use between the mains and the switch for turning the lamp load on/off shall not exceed 0,50 W...: For lamp control gear with output power () over 250 W, the no-load power limits shall be multiplied by /250 W : The standby power of a lamp control gear shall not exceed 0,50 W.: Limit: Limit: 2 FUNCTIONALITY REQUIREMENTS 2.1 Functionality requirements for directional lamps other than LED lamps Table 3 Functionality requirements for directional compact (see Annex 2) fluorescent lamps If the lamp cap is a standardised type also used with filament lamps, then as from stage 2, the lamp shall comply with state-of-the-art requirements for compatibility with equipment designed for installation between the mains and filament lamps.

8 age 8 of 24 Report No.: GZES Clause Requirement + Test Result - Remark Verdict Table 4 Functionality requirements for other directional lamps (excluding LED lamps, compact fluorescent lamps and high-intensity discharge lamps) (see Annex 3) 2.2 Functionality requirements for non-directional and directional LED lamps Table Stage 2 Functionality requirements for non-directional and (see Annex 4) directional LED lamps If the lamp cap is a standardised type also used with filament lamps, then as from stage 2 the lamp shall comply with state-of-the-art requirements for compatibility with equipment designed for installation between the mains and filament lamps. Functionality requirement for equipment designed for installation between the mains and the lamps Equipment designed for installation between the mains and the lamps shall comply with state-ofthe-art requirements for compatibility with lamps whose energy efficiency index is at most: 0,24 for non-directional lamps (assuming that Ф use = total rated luminous flux), 0,40 for directional lamps. A dimming control device is switched on at its lowest control setting for which the operated lamps consume power, the operated lamps shall emit at least 1 % of their luminous flux at full load.. : A luminaire is placed on the market and intended to be marketed to the end-users, and lamps that the end- user can replace are included with the luminaire, these lamps shall be of one of the two highest energy classes, according to Commission Delegated Regulation (EU) No 874/2012, with which the luminaire is labelled to be compatible. 3 RODUCT INFORMATION REQUIREMENTS 3.1 roduct information requirements for directional lamps Stage 1 The following information shall be provided as from stage 1, except where otherwise stipulated. These information requirements do not apply to: filament lamps not fulfilling the efficacy requirements of Stage 2, LED modules when marketed as part of a luminaire from which they are not intended to be removed by the end-user. In all forms of product information, the term energy-saving lamp or any similar product related promotional statement about lamp efficacy may be used only if the energy efficiency index of the lamp (calculated in accordance with the method set out in point 1.1 of this Annex) is 0,40 or below Information to be displayed on the lamp itself

9 age 9 of 24 Report No.: GZES Clause Requirement + Test Result - Remark Verdict Lamps other than high-intensity discharge lamps, the value and unit ( lm, K and ) of the nominal useful luminous flux, of the colour temperature and of the nominal beam angle shall be displayed in a legible font on the surface of the lamp. Information to be visibly displayed to end-users, prior to their purchase, on the packaging and on free access websites The information in paragraphs (a) to (o) below shall be displayed on free access websites and in any other form the manufacturer deems appropriate. If the product is placed on the market in a packaging containing information to be visibly displayed to the end- users, prior to their purchase, the information shall also be clearly and prominently indicated on the packaging. The information does not need to use the exact wording on the list below. It may be displayed in the form of graphs, drawings or symbols rather than text. (a) Nominal useful luminous flux displayed in a font at least twice as large as any display of the nominal lamp power; (b) Nominal life time of the lamp in hours (not longer than the rated life time); (c) Colour temperature, as a value in Kelvins and also expressed graphically or in words; (d) Number of switching cycles before premature failure; (e) Warm-up time up to 60 % of the full light output (may be indicated as instant full light if less than 1 second); (f) A warning if the lamp cannot be dimmed or can be dimmed only on specific dimmers; in the latter case a list of compatible dimmers shall be also provided on the manufacturer's website; (g) If designed for optimum use in non-standard conditions (such as ambient temperature Ta 25 C or specific thermal management is necessary), information on those conditions; (h) Lamp dimensions in millimetres (length and largest diameter); (i) Nominal beam angle in degrees; (j) If the lamp s beam angle is 90and its useful luminous flux as defined in point 1.1 of this Annex is to be measured in a 120cone, a warning that the lamp is not suitable for accent lighting; (k) If the lamp cap is a standardised type also used with filament lamps, but the lamp s dimensions are different from the dimensions of the filament lamp(s) that the lamp is meant to replace, a drawing comparing the lamp s dimensions to the dimensions of the filament lamp(s) it replaces;

10 age 10 of 24 Report No.: GZES Clause Requirement + Test Result - Remark Verdict (l) An indication that the lamp is of a type listed in the first column of Table 6 may be displayed only if the luminous flux of the lamp in a 90 cone (Ф90) is not lower than the reference luminous flux indicated in Table 6 for the smallest wattage among the lamps of the type concerned. (m) An equivalence claim involving the power of a replaced lamp type may be displayed only if the lamp type is listed in Table 6 and if the luminous flux of the lamp in a 90 cone (Ф90) is not lower than the corresponding reference luminous flux in Table 6. If the lamp contains mercury: (n) Lamp mercury content as X,X mg; (o) Indication of which website to consult in case of accidental lamp breakage to find instructions on how to clean up the lamp debris. Information to be made publicly available on free-access websites and in any other form the manufacturer deems appropriate As a minimum, the following information shall be expressed at least as values. (a) The information specified in point 3.1.2; (b) Rated power (0,1 W precision); (c) Rated useful luminous flux; (d) Rated lamp life time; (e) Lamp power factor; (f) Lumen maintenance factor at the end of the nominal life (except for filament lamps); (g) Starting time (as X,X seconds); (h) Colour rendering; (i) Colour consistency (only for LEDs); (j) Rated peak intensity in candela (cd); (k) Rated beam angle; (l) If intended for use in outdoor or industrial applications, an indication to this effect; (m) Spectral power distribution in the range nm; If the lamp contains mercury: (n) Instructions on how to clean up the lamp debris in case of accidental lamp breakage; (o) Recommendations on how to dispose of the lamp at the end of its life for recycling in line with Directive 2012/19/EU of the European arliament and of the Council ( 1 ). Additional product information requirements for LED lamps replacing fluorescent lamps without integrated ballast

11 age 11 of 24 Report No.: GZES Clause Requirement + Test Result - Remark Verdict Stage Stage 2 Manufacturers of LED lamps replacing fluorescent lamps without integrated ballast shall publish a warning on publicly available free-access websites and in any other form they deem appropriate that the overall energy efficiency and light distribution of any installation that uses such lamps are determined by the design of the installation. Claims that an LED lamp replaces a fluorescent lamp without integrated ballast of a particular wattage may be made only if: The luminous intensity in any direction around the tube axis does not deviate by more than 25 % from the average luminous intensity around the tube, and The luminous flux of the LED lamp is not lower than the luminous flux of the fluorescent lamp of the claimed wattage. The luminous flux of the fluorescent lamp shall be obtained by multiplying the claimed wattage with the minimum luminous efficacy value corresponding to the fluorescent lamp in Commission Regulation (EC) No 245/2009, and The wattage of the LED lamp is not higher than the wattage of the fluorescent lamp it is claimed to replace. The technical documentation file shall provide the data to support such claims. roduct information requirements for equipment other than luminaires, designed for installation between the mains and the lamps If the equipment provides no compatibility with any of the energy-saving lamps according to part 2.3 of this Annex, a warning that the equipment is not compatible with energy-saving lamps shall be published on publicly available free-access websites and in other forms the manufacturer deems appropriate. 3.4 roduct information requirements for lamp control gears Stage 2 the following information shall be published on publicly available free access websites and in other forms the manufacturer deems appropriate: Indication that the product is intended to be used as a lamp control gear, If applicable, the information that the product may be operated in no-load mode.

12 ANNEX 1 age 12 of 24 Report No.: GZES Table 2: The maximum EEI of directional lamps TABLE 1 CORRECTION FACTORS cor = rated 1,06 cor = rated 1,10 cor = rated 0,80 cor = rated 0,85 cor = Sample Фuse (lm): rated (W): Energy efficiency index (EEI) Test voltage (V): Average Ф use (lm): Average rated (W): cor (W): Average EEI: Energy efficiency class ref (W): Ф use < 1300 lm: Ф use 1300 lm: ref = 0,07341Ф use

13 ANNEX 1 age 13 of 24 Report No.: GZES Table 2: The maximum EEI of directional lamps TABLE 2 Maximum energy efficiency index (EEI) Lamp type Mainsvoltage filament lamps: Other filament lamps: Highintensity discharge lamps: Other lamps: Application stage Limit for Stage 1 If Ф use > 450 lm: 1,75 Ф use = lm Limit for Stage 2 Limit for Stage 3 Calculated EEI Verdict 1,75 0,95 If Ф use 450 lm: 1,20; If Ф use > 450 lm: 0,95 0,95 0,95 Ф use = lm 0,50 0,50 0,36 0,50 0,50 0,20

14 ANNEX 2 age 14 of 24 Report No.: GZES Table 3: Functionality requirements for directional compact fluorescent lamps Type reference: Functionality parameter Limit for Stage 1 except where indicated otherwise Limit for Stage 3 Lamp survival factor at 6000 h From 1 March 2014: 0,50 0,70 Lumen maintenance At h: 80 % At h: 83 % At h: 70 % Number of switching cycles half the lamp lifetime expressed in hours: if lamp starting time > 0,3 s lamp lifetime expressed in hours: if lamp starting time > 0,3 s Starting time (s) < 2,0 < 1,5; if < 10 W < 1,0; if 10 W Lamp warm-up time to 60 % Ф (s) < 40 < 100 for lamps containing mercury in amalgam form < 40 < 100 for lamps containing mercury in amalgam form remature failure rate 5,0 % at 500 h 5,0 % at 1000 h Lamp power factor (F) 0,50 if < 25 W 0,90 if 25 W 0,55 if < 25 W 0,90 if 25 W Colour rendering (Ra) if the lamp is intended for outdoor or industrial applications according to point 3.1.3(l) of this Annex if the lamp is intended for outdoor or industrial applications according to point 3.1.3(l) of this Annex Average results Verdict

15 ANNEX 2 age 15 of 24 Report No.: GZES Table 3: Functionality requirements for directional compact fluorescent lamps Tests results for 20 samples: Sample Number of switching cycles before failure Starting time (s) Lamp warm-up time to 60% Ф (s) Colour rendering (Ra)

16 age 16 of 24 Report No.: GZES ANNEX 3 Table 4: Functionality requirements for other directional lamps (excluding LED lamps, compact fluorescent lamps and high-intensity discharge lamps) Type reference: Functionality parameter Rated lamp lifetime at 50 % lamp survival Lumen maintenance Number of switching cycles Starting time (s) Lamp warmup time to 60 % Ф (s) remature failure rate Lamp power factor (F) 1000 h Limit for Stage 1 and h in stage 2000 h for extra low voltage lamps not complying with the stage 3 filament lamp efficiency requirement in point 1.1 of this Annex 80 % at 75 % of rated average lifetime four times the rated lamp life expressed in hours: < 0,2 1,0 5,0 % at 100 h ower 25 W: 0,9 ower 25 W: 0,5 Limit for Stage h 4000 h for extra low voltage lamps 85 % at 75 % of rated average lifetime four times the rated lamp life expressed in hours: < 0,2 1,0 5,0 % at 200 h ower 25 W: 0,9 ower 25 W: 0,5 Average results Verdict

17 age 17 of 24 Report No.: GZES ANNEX 3 Table 4: Functionality requirements for other directional lamps (excluding LED lamps, compact fluorescent lamps and high-intensity discharge lamps) Tests results for 20 samples: Sample Number of switching cycles Starting time (s) Lamp warm-up time to 60% Ф (s)

18 ANNEX 4 age 18 of 24 Report No.: GZES Table 5: Functionality requirements for non-directional and directional LED lamps Type reference: Functionalit y parameter Limit for Stage 1 except where indicated otherwise Lamp survival factor at 6000 h From 1 March 2014: 0,90 Lumen Maintenance at 6000 h From 1 March 2014: 0,80 Number of switching cycles if rated lamp life h otherwise half the rated lamp life expressed in hours: Starting time (s) EH1622 Lamp warmup time to 95 % Ф (s) < 0,5 < 2 rematur e failure rate 5,0 % at 1000 h Colour rendering (Ra) if the lamp is intended for outdoor or industrial applications in accordance with point 3.1.3(l) of this Annex Colour consistency Variation of chromaticity coordinates within a sixstep MacAdam ellipse or less Lamp power factor (F) 2 W: no requir ement 2 W < 5 W: F > 0,4 5 W < 25 W: F > 0,5 > 25 W: F > 0,9 Average results 1 0,83 > ,47 0, ,3 2,6 Verdict

19 ANNEX 4 age 19 of 24 Report No.: GZES Table 5: Functionality requirements for non-directional and directional LED lamps Tests results for 20 samples: Lumen Sample Maintenance at 6000 h (%) Number of switching cycles before failure Starting time (s) Lamp warm-up time to 95%Ф (s) Colour rendering (Ra) 1 84,0 > ,471 0,5 81,3 2 80,9 > ,445 0,5 82,1 3 86,4 > ,459 0,5 81,6 4 87,2 > ,458 0,5 82,3 5 85,0 > ,489 0,5 81,6 6 83,7 > ,476 0,5 81,7 7 81,7 > ,448 0,5 81,4 8 84,2 > ,454 0,5 81,4 9 86,1 > ,467 0,5 81, ,9 > ,478 0,5 81, ,9 > ,453 0,5 82, ,0 > ,475 0,5 82, ,2 > ,467 0,5 82, ,6 > ,481 0,5 81, ,4 > ,424 0,5 81, ,2 > ,436 0,5 81, ,9 > ,445 0,5 81, ,8 > ,464 0,5 81, ,1 > ,452 0,5 82, ,1 > ,471 0,5 81,3

20 ANNEX 5 Additional requirement of 244/2009/EU age 20 of 24 Report No.: GZES ANNEX II Ecodesign requirements for non-directional household lamps: 1 LAM EFFICACY REQUIREMENTS Table 1 Maximum rated power (max) for a given rated luminous flux (Ф) (W) Clear lamps Stages 1 to 5: 0,8 * (0,88 Ф+0,049Ф) Stage 6: 0,6 * (0,88 Ф+0,049Ф) Average Luminous flux (lm) Calculated max (W) Average wattage (W) Non-clear lamps Stages 1 to 5: 0,24 Ф+0,0103Ф Stages 6: 0,24 Ф+0,0103Ф Average Luminous flux (lm) 365,07 Calculated max (W) 8,35 Average wattage (W) 7,26 Table 2 Maximum rated power (max) for a given rated luminous flux (Ф) (W) Clear lamps 60 lm Ф 950 lm in Stage 1: max = 1,1 * (0,88 Ф+0,049Ф) Clear lamps 60 lm Ф 725 lm in Stage 2: max = 1,1 * (0,88 Ф+0,049Ф) Clear lamps 60 lm Ф 450 lm in Stage 3: max = 1,1 * (0,88 Ф+0,049Ф) Clear lamps with G9 or R7s cap in Stage 6: max = 0,8 * (0,88 Ф+0,049Ф) Average Luminous flux (lm) Calculated max (W) Average wattage (W) Table 3 Correction factors filament lamp requiring external power supply: max/1,06 discharge lamp with cap GX53: max/0,75 non-clear lamp with colour rendering index 90 and 0,5 * (0,88 Ф+0,049Ф): max/0,85 discharge lamp with colour rendering index 90 and Tc K: max/0,76 non-clear lamp with second envelope and 0,5 * (0,88 Ф+0,049Ф): max/0,95 LED lamp requiring external power supply: max/1,1 Average Luminous flux (lm) 365,07 Calculated max (W) 7,59 Average wattage (W) 7,26 3 RODUCT INFORMATION REQUIREMENTS ON LAMS 3.1 For non-directional household lamps, the following information shall be provided as from Stage 2, except where otherwise stipulated Information to be visibly displayed prior to purchase to end-users on the packaging and on free access websites

21 ANNEX 5 Additional requirement of 244/2009/EU age 21 of 24 Report No.: GZES (a) When the nominal lamp power is displayed outside the energy label in accordance with Directive 98/11/EC, the nominal luminous flux of the lamp shall also be separately displayed in a font at least twice as large as the nominal lamp power display outside the label (b) Nominal life time of the lamp in hours (not higher than the rated life time) (c) Number of switching cycles before premature lamp failure (d) Colour temperature (also expressed as a value in Kelvins) (e) Warm-up time up to 60 % of the full light output (may be indicated as instant full light if less than 1 second) (f) A warning if the lamp cannot be dimmed or can be dimmed only on specific dimmers (g) If designed for optimal use in non-standard conditions (such as ambient temperature Ta 25 C), information on those conditions; (h) Lamp dimensions in millimeters (length and diameter) (i) If equivalence with an incandescent lamp is claimed on the packaging, the claimed equivalent incandescent lamp power (rounded to 1 W) shall be that corresponding in Table 6 to the luminous flux of the lamp contained in the packaging. (j) The term energy saving lamp or any similar product related promotional statement about lamp efficacy may only be used if the lamp complies with the efficacy requirements applicable to non-clear lamps in Stage 1 according to Tables 1, 2 and 3. If the lamp contains mercury (k) Lamp mercury content as X,X mg (l) Indication which website to consult in case of accidental lamp breakage to find instructions on how to clean up the lamp debris 3.2 Information to be made publicly available on free-access websites (a) The information specified in point 3.1 (b) Rated wattage (0,1 W precision) (c) Rated luminous flux (d) Rated lamp life time (e) Lamp power factor (f) Lumen maintenance factor at the end of the nominal life (g) Starting time (as X,X seconds) (h) Colour rendering If the lamp contains mercury

22 ANNEX 5 Additional requirement of 244/2009/EU age 22 of 24 Report No.: GZES (i) Instructions on how to clean up the lamp debris in case of accidental lamp breakage (j) Recommendations on how to dispose of the lamp at its end of life ANNEX VI Energy efficiency classes The energy efficiency class of a lamp shall be determined as follows: Lamps operating on external halogen lamp control gear cor = rated 1,06 Lamps operating on external LED lamp control gear cor = rated 1,10 = 7,26 x 1,10 = 7,99 Fluorescent lamps of 16 mm diameter (T5 lamps) and 4-pin single capped fluorescent lamps cor = rated 1,10 operating on external fluorescent lamp control gear cor = Other lamps operating on external fluorescent lamp control gear Lamps operating on external high-intensity discharge lamp control gear cor = rated 1,10 Lamps operating on external low pressure sodium lamp control gear cor = rated 1,15 For models with Φ use < lumen: 365,07 lm ref = 0,88 Φ use + 0,049 use: 34,70 W For models with Φ use lumen: ref = 0,07341Φ use : EEI = cor / ref : 7,99 W / 34,70 W = 0,23 Energy efficiency class EEI for nondirectional lamps EEI for directional lamps A++ EEI 0,11 EEI 0,13 A+ 0,11 < EEI 0,17 0,13 < EEI 0,18 A 0,17 < EEI 0,24 0,18 < EEI 0,40 0,23 B 0,24 < EEI 0,60 0,40 < EEI 0,95 C 0,60 < EEI 0,80 0,95 < EEI 1,20 D 0,80 < EEI 0,95 1,20 < EEI 1,75 E EEI > 0,95 EEI > 1,75

23 ANNEX 6 hoto documentation age 23 of 24 Report No.: GZES Type of equipment, model: EH1622 Details of: General view View: [ ] general [ ] front [ ] rear [ ] right [ ] left [ ] top [ ] bottom Details of: LED lamp View: [ ] general [ ] front [ ] rear [ ] right [ ] left [ ] top [ ] bottom

24 ANNEX 6 hoto documentation age 24 of 24 Report No.: GZES Details of: LED modules View: [ ] general [ ] front [ ] rear [ ] right [ ] left [ ] top [ ] bottom End of Report - - -