SECTION 10 57 23.13 (10670) - WIRE CLOSET AND UTILITY SHELVING PART 1 GENERAL 1.01 SUMMARY 1. Wire Closet Shelves B. Related Sections: 1.02 SUBMITTALS 1. Section 06 10 00 (06100) - Rough Carpentry A. Submit "Letter of Conformance" in accordance with Section 01 33 00 (01330) with the following supporting data: 1. Mark each copy to identify applicable products, characteristics, models, options and other supplemental data to clearly communicate information specific to this Project. 2. Color Chart: Each product specified. 1.03 QUALITY ASSURANCE A. Installer Qualifications: Manufacturer's authorized representative who is trained and approved for installation of units required for this Project. B. Source Limitations: Obtain metal storage shelving through one source from a single manufacturer. 1.04 DELIVERY, STORAGE, AND HANDLING A. Deliver storage shelving palleted, wrapped, or crated to provide protection during transit and Project-site storage. 1.05 PROJECT CONDITIONS A. Environmental Limitations: Do not deliver or install metal storage shelving until spaces are enclosed and weatherproof, wet work in spaces is completed and dry, and ambient temperature is being maintained at the levels indicated for Project when occupied for its intended use. PART 2 PRODUCTS 2.01 WIRE CLOSET SHELVES A. Avendra, LLC Preferred Manufacturers: 1. None B. Approved Manufacturers: 1. Lifetime Ventilated Series Shelf with Hanging Rod ; Organized Living (888-674-5484) C. Components: 1. Structural Performance: a. Structural Performance: Back clips spaced 11 inches with support braces at 3 feet 6 inches. b. Static Load: 75 lb/ft of shelf minimum. c. For heavy duty applications in pantry and garage applications space support brace on 2 feet. PAGE 1
d. Back Clips and Down Back Clips shall be Tri-Loc II Patented hollow wall anchoring system. 2. Material: Minimum requirements. a. Steel Rod: Grade C 1008 cold drawn steel rod. Tensile strength of 100 ksi. b. Front Rods and Studs: 0.306 inch diameter. c. Back Rods: 0.243 inch diameter. d. Cross Wire Spacing: 1 inch spacing. 0.120 inch diameter for one inch spaced standard 20 inches shelf. 0.105 inch diameter for one inch spaced standard mesh shelf. e. Cross Wire Spacing: 1/2 inch spacing. 0.0915 inch diameter for one-half inch spaced tight mesh shelf. 3. Shelving: a. Hanging Shelf with Open Slide: 12 inches deep by length as shown on Drawings. b. Storage Shelf: 12 inches deep by length as shown on Drawings. 4. Mounting Hardware: Manufacturer's standard components including anchor clips, end brackets, angled support braces and end caps, including the following: D. Finish: a. Side Wall Bracket: As required. Shelf side wall interface. b. Support Brace: Maximum 42 inches and every open end Anchor Back Clips. c. Fasteners, clips, caps and touch-up all as required. d. Down Back Clips. 1. Electrostatic applied oven cured epoxy at all surfaces to 3 to 5 mil thickness. a. Color: Pure White E. Configurations: Note: Descriptions below are based on the Closet configurations shown on the Drawings. Verify configurations and parts list below with actual Project room sizes and configurations. Contact the Organized Living company for any modifications required. 1. Standard King Guestroom Wire Shelves: (Drawing 420) PAGE 2 REVISED: 06/08/15 FILE: 10-105723_13-C-Wire Closet And Utility Shelving CFRST SPECMSTR-NEW BUILD 2015, Marriott International, Inc.
2. Accessible King Guestroom Wire Shelves: (Drawing 421) above finished floor. Hanging rod to be located under open section of Closet 1 (Up to 30 Wide) 3. Extended King Guestroom Wire Shelves: (Drawing 422) 4. King Suite A Guestroom Wire Shelves: (Drawing 426) PAGE 3
5. King Suite B Guestroom Wire Shelves: (Drawing 427) 6. Accessible King Suite B Guestroom Wire Shelves: (Drawing 428) above finished floor. Hanging rod to be located under open section of PAGE 4 REVISED: 06/08/15 FILE: 10-105723_13-C-Wire Closet And Utility Shelving CFRST SPECMSTR-NEW BUILD 2015, Marriott International, Inc.
7. King Inline Suite Guestroom Wire Shelves: (Drawing 429) 8. Accessible King Inline Suite Guestroom Wire Shelves: (Drawing 430) above finished floor. Hanging rod to be located under open section of PAGE 5
Closet 1 (Up to 30 Wide) 9. Standard Queen/Queen Guestroom Wire Shelves: (Drawing 431) 4 1430-6693-11 Medium End Cap White 4 1430-6694-11 Large End Cap White 10. Accessible Queen/Queen Guestroom Wire Shelves: (Drawing 432) above finished floor. Hanging rod to be located under open section of Closet 1 (Up to 30 Wide) PAGE 6 REVISED: 06/08/15 FILE: 10-105723_13-C-Wire Closet And Utility Shelving CFRST SPECMSTR-NEW BUILD 2015, Marriott International, Inc.
11. Extended Queen/Queen Guestroom Wire Shelves: (Drawing 433) 4 1430-6693-11 Medium End Cap White 4 1430-6694-11 Large End Cap White 12. Queen/Queen Suite B Guestroom Wire Shelves: (Drawing 434) 4 1430-6693-11 Medium End Cap White 4 1430-6694-11 Large End Cap White 4 1430-6693-11 Medium End Cap White 4 1430-6694-11 Large End Cap White 13. Accessible Queen/Queen Suite B Guestroom Wire Shelves: (Drawing 435) above finished floor. Hanging rod to be located under open section of PAGE 7
14. Queen/Queen Inline Suite Guestroom Wire Shelves: (Drawing 436) 15. Accessible Queen/Queen Inline Suite Guestroom Wire Shelves: (Drawing 437) above finished floor. Hanging rod to be located under open section of PAGE 8 REVISED: 06/08/15 FILE: 10-105723_13-C-Wire Closet And Utility Shelving CFRST SPECMSTR-NEW BUILD 2015, Marriott International, Inc.
PART 3 EXECUTION 3.01 INSTALLATION Closet 1 (Up to 30 Wide) A. Install in accordance with manufacturer's published instructions, square and plumb, secured rigidly in position. 1. Layout scheduled components prior to installation to verify wall to wall and floor to ceiling heights, widths, plumb and flatness of surfaces. 2. Prepare anchor locations and select anchor types using the methods recommended by the manufacturer for achieving the best result for the substrate under the project conditions. END OF SECTION PAGE 9