Swing Arm TV Wall Mount Model Number: AWBS-0816-W INSTRUCTION MANUAL AUS 1300 886 649 Model: AWBS-0816-W Product Code: 54265 08/2017
Contents Warranty Details 3 Welcome 4 General Safety Instructions 5 Parts List 6 Getting Started 7 Installation 8 Repair and Refurbished Goods or Parts Notice 14 2 AUS 1300 886 649 Model: AWBS-0816-W Product Code: 54265 08/2017
Swing Arm TV Wall Mount Warranty Details The product is guaranteed to be free from defects in workmanship and parts for a period of 12 months from the date of purchase. Defects that occur within this warranty period, under normal use and care, will be repaired, replaced or refunded at our discretion, solely at our option with no charge for parts and labour. The benefits conferred by this warranty are in addition to all rights and remedies in respect of the product that the consumer has under the Competition and Consumer Act 2010 and similar state and territory laws. Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and to compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. AUS 1300 886 649 Model: AWBS-0816-W Product Code: 54265 08/2017 3
Welcome Congratulations on choosing to buy a BAUHN product. All products brought to you by BAUHN are manufactured to the highest standards of performance and safety and, as part of our philosophy of customer service and satisfaction, are backed by our comprehensive 1 Year Warranty. We hope you will enjoy using your purchase for many years to come. 4 AUS 1300 886 649 Model: AWBS-0816-W Product Code: 54265 08/2017
General Safety Instructions Read this manual thoroughly before installing the Swing Arm Wall Bracket to ensure your personal and other people s safety and to avoid any property loss. If you do not understand these directions, or have any questions in relation to the safety of the installation, we recommend you contact a qualified professional. For all other general inquiries, please contact the after sales support line on the number at the bottom of the page. Before installation, check carefully to ensure that there are no missing or defective parts. All parts are listed and illustrated on the following page. Never use defective parts. Our customer service representatives can quickly assist you with installation questions and replacement for missing or defective parts. Do not use this product for any purpose that is not explicitly specified in this manual. Handle and use the bracket strictly according to the instructions. Improper installation may cause damage or serious injury. We assume no liability for any eventual damage or injury caused by incorrect mounting, incorrect assembly or incorrect use. This product is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. This is not a toy. Keep the Swing Arm Wall Bracket away from infants and children. Young children should be supervised to ensure they do not play with the product. Mount the wall plate far away from any water source and direct sunlight. WARNING: Choose a structurally-sound wall area that is strong enough to hold the weight of the TV as well as the wall bracket. WARNING: DO NOT attach the wall mount to a hollow wall or decorative room divider. Only use this Swing Arm Wall Bracket in accordance with the technical specifications below: For TV screen size: 13 up to 55 (33cm - 139cm) Maximum weight load: 40kg Adjustable tilt angle: -8 to +8 up/down Adjustable pan angle: 90 left and 90 right Distance from wall: 65-438mm Supported VESA dimensions: 75x75, 100x100, 100x200, 200x200 and 400x400. AUS 1300 886 649 Model: AWBS-0816-W Product Code: 54265 08/2017 5
Parts List Assembly hardware The illustration below is to help you identify the parts; some parts are not shown at the same scale. Installation Pack A B C D* E 8 x 50mm x3 ø10 x ø8 x 50mm x3 D5 x4 D6 x12 D8 x4 F G* H I J M5 x 12mm x4 M6 x 12mm x12 M8 x 15mm x4 4mm Allen Key x1 M6 x8 D*/G*: Eight pieces each are for attaching the TV mounting plate arms. Wall plate Plastic cover TV mounting plate 2 UP marker Extension arm (K) Swing Arm Wall Bracket 1pc 1 TV Mounting Plate Arms 2pcs each of type (1) and (2) NOTE: Required to mount TVs with 400x400 VESA hole pattern. 6 AUS 1300 886 649 Model: AWBS-0816-W Product Code: 54265 08/2017
Getting Started Before you start installing the wall bracket Unpack the product but keep all packaging materials until you have made sure your new Swing Arm Wall Bracket is undamaged. (In case of damage, contact our After Sales Support line for advice on examination, repair or return of the damaged product). Plastic wrapping can be a suffocation hazard for babies and young children, so ensure all packaging materials are out of their reach. Read this manual to familiarise yourself with all the parts and installation instructions. Pay particular attention to the safety instructions on page 5. All the parts that are supplied for installation are pictured on page 6 with their respective part identification letter (A to J). Sort the items accordingly so you know which ones to use during installation. IMPORTANT! Only install this bracket on a structurally-sound wall area that is strong enough to hold the weight of the TV as well as the wall mount. Mount the bracket far away from any water source and direct sunlight. DO NOT attach the bracket to a hollow wall or decorative room divider. Consult your builder for advice if you want to install the bracket to a wood stud wall. The wall must be strong enough for the weight of the bracket and the TV. This Swing Arm Wall Bracket consists of a wall plate with a swing arm and a TV mounting plate at the end. You first affix the wall plate to the wall, then you will need help to attach your TV to the TV mounting plate. CAUTION! At least two people are required to install this Swing Arm Wall Bracket. Do not attempt to assemble it independently to avoid incorrect assembly or any possible injury this may cause. AUS 1300 886 649 Model: AWBS-0816-W Product Code: 54265 08/2017 7
Installation Before Starting Installation Tools Needed Pencil Phillips Screwdriver Socket Wrench Steel Measuring Tape 10mm Hammer Electric Drill Concrete Bit Ensure the TV mounting plate is detached from the swing arm. 1. Unscrew the bolt behind the TV mounting plate using a Phillips head screwdriver. See Fig. 1. 2. Pull the TV mounting plate upwards to detach it from the swing arm. Bolt TV Mounting Plate Fig. 1 Step 1: Attaching the wall plate a) Remove the plastic cover over the wall mount plate by placing your fingers on top and bottom edges and pulling it out. b) Using the wall plate and spirit level, outline the location of the three holes on the wall. Ensure the holes are aligned. NOTE: If you want to install the wall mount to a wood stud wall, consult your builder for advice. The wall must be strong enough for the weight of the wall mount and the TV. 8 AUS 1300 886 649 Model: AWBS-0816-W Product Code: 54265 08/2017
Installation (Cont.) c) Using the masonry bit, pre-drill three holes:10mm in diameter and 50mm deep at each marked spot on a concrete or brick wall (see Fig. 2 below). WARNING: Do not drill into mortar joints. 50mm 10mm Diameter masonry bit Fig. 2 d) Place the masonry plugs (B) into the holes and gently tap them with a hammer until they are flush with the wall (Fig. 3). (B) x 3 Fig. 3 e) Use the three screws (A) to affix the Swing Arm Wall Bracket (K) into the anchors in the wall, as illustrated below (Fig. 4), and then tighten the screws securely. (A) x 3 Fig. 4 AUS 1300 886 649 Model: AWBS-0816-W Product Code: 54265 08/2017 9
Installation (Cont.) Step 2: Attaching the TV to the TV mounting plate For TVs with 75x75, 100x100, 100x200 and 200x200 VESA patterns: a) When the wall plate is properly attached to the wall, pull the swing arm out as far out from the wall as possible. b) Lay your TV face down on something soft so as not to scratch the TV screen. Check the back of your TV to find the appropriate mounting pattern. c) On the rear of the TV, locate the screw holes used for attaching a wall bracket. Position the assembled TV mounting plate over these holes. Select the appropriate bolts (F/G/H) and washers (C/D/E) that fit the thread holes at the back of your TV monitor. NOTE: Due to the many varieties of television, you may need to visit your local hardware supplier to find the correct bolt and washer sizes. d) Insert the four selected bolts through the appropriate washers (C/D/E) and the corresponding holes on the TV mounting plate into the thread holes on the back of the TV, then tighten the bolts. e) Carefully lift TV and hook the TV mounting plate over the swing arm. Do not let go of the TV until the it is securely in place on the swing arm. f) Tighten the bolt to secure the TV using a Philips-head screwdriver. This will help ensure that your TV does not fall off the wall mount during use. NOTE: Ensure you have two people to perform steps (e) and (f) to avoid damaging the TV or causing injury. (F-H) Screws Fig. 5 (C-E) Washers TV 10 AUS 1300 886 649 Model: AWBS-0816-W Product Code: 54265 08/2017
Installation (Cont.) For TVs with 400x400 VESA pattern: a) When the wall plate is properly attached to the wall, pull the swing arm out as far out from the wall as possible. b) Lay your TV face down on something soft so as not to scratch the TV screen. Check the back of your TV to find the appropriate mounting pattern. c) Select Screws (G), Washers (D) and Nuts (J) to attach the TV mounting plate arms to the TV mounting plate as shown in the diagram below. (See Fig. 6 below). Use TV mounting plate arms type 1 on the top right and bottom left corners, and type 2 on the top left and bottom right corners. NOTE: Use a Phillips-head screwdriver and socket wrench to securely tighten the TV mounting plate arms to the TV mounting plate. d) On the rear of the TV, locate the screw holes used for attaching a wall bracket. Position the assembled TV mounting plate over these holes. Insert the four selected bolts through the appropriate washers (C/D/E) and the corresponding holes on the TV mounting plate and into the thread holes on the back of the TV, as shown in Fig. 5 on page 10. (The illustration shows the TV mounting plate without the attached swing arm and wall plate, for better visibility). Then tighten the bolts. e) Carefully lift TV and hook the TV mounting plate over the swing arm. Do not let go of the TV until the it is securely in place on the swing arm. f) Tighten the bolt to secure the TV using a Philips-head screwdriver. This will help ensure that your TV does not fall off the wall mount during use. NOTE: Ensure you have two people to perform steps (e) and (f) to avoid damaging the TV or causing injury. Fig. 6 (D) x Washer (G) x Screws 2 1 (J) Nuts 1 2 AUS 1300 886 649 Model: AWBS-0816-W Product Code: 54265 08/2017 11
Installation (Cont.) Step 3: Adjusting the viewing angle a) The illustration below shows all the parts of the completed Swing Arm Wall Bracket. b) To adjust the viewing angle upwards or downwards, loosen the adjustment bolts (see below) with the supplied Allen Key (I) and tilt the monitor on the mounting plate slightly. Tighten the adjustment bolts securely after you have found the correct viewing angle. Take care not to overtighten. c) To adjust the viewing distance and/or the viewing angle to the left or right, move the swing arm (illustrated on the next page). (adjustment bolts) TV Wall IMPORTANT! Attaching a flat panel TV to a wall mount requires specialist knowledge. We assume no liability for any injury or material damage incurred due to incorrect assembly or use. Make sure to follow all instructions in this manual, and if you require professional advice, please consult a relevant tradesperson. 12 AUS 1300 886 649 Model: AWBS-0816-W Product Code: 54265 08/2017
Installation (Cont.) WARNING! Tighten all bolts necessary for the installation of the Swing Arm Wall Bracket firmly to ensure the wall plate is securely attached to the wall and the mounting plate to the TV monitor. Do not overtighten them, or you could damage them and greatly reduce their holding power. Tighten all the screws securely with the supplied Allen key (I). Do no remove or loosen any screw or bolt until it is no longer engaged with the mount. Doing so may cause the screen to fall. Distance to the wall: 65-438mm 180 adjustable 8 8 AUS 1300 886 649 Model: AWBS-0816-W Product Code: 54265 08/2017 13
Swing Arm TV Wall Mount Repair and Refurbished Goods or Parts Notice REGISTER YOUR PURCHASE AT www.aldi.com.au/en/about-aldi/product-registration TO KEEP UPDATED WITH IMPORTANT PRODUCT INFORMATION Unfortunately, from time to time, faulty products are manufactured and may need to be returned to the supplier for repair. Please be aware that if your product is capable of retaining user-generated data (such as files stored on a computer hard drive, telephone numbers stored on a mobile telephone, songs stored on a portable media player, games saved on a games console or files stored on a USB memory stick) during the process of repair, some or all of your stored data may be lost. We recommend you save this data elsewhere prior to sending the product for repair. You should also be aware that rather than repairing goods, we may replace them with refurbished goods of the same type or use refurbished parts in the repair process. Please be assured though, refurbished parts or replacements are only used where they meet ALDI s stringent quality specifications. If at any time you feel your repair is being handled unsatisfactorily, you may escalate your complaint. Please telephone us on 1300 886 649 or write to us at: Tempo (Aust) Pty Ltd ABN 70 106 100 252 PO BOX 6056 Frenchs Forest, Sydney, Australia NSW 2086 Tempo Help Desk: 1300 886 649 (Aust) (Operating Hours: Mon-Fri 08:30AM to 06:00PM AEST) Email: info@tempo.org AUS 1300 886 649 Model: AWBS-0816-W Product Code: 54265 08/2017
AUS This page has been left blank intentionally. 1300 886 649 Model: AWBS-0816-W Product Code: 54265 08/2017 15
Warranty returns Should you for any reason need to return this product for a warranty claim, make sure to include all accessories with the product. Product does not work? If you encounter problems with this product, or if it fails to perform to your expectations, make sure to contact our After Sales Support Centre on 1300 886 649 before returning it to the store for a refund.