DBR based passively mode-locked 1.5m semiconductor laser with 9 nm tuning range Moskalenko, V.; Williams, K.A.; Bente, E.A.J.M.

Similar documents
Frequency Noise Reduction of Integrated Laser Source with On-Chip Optical Feedback

Slot waveguide microring modulator on InP membrane

Published in: Proceedings of the 20th Annual Symposium of the IEEE Photonics Benelux Chapter, November 2015, Brussels, Belgium

High-Resolution AWG-based fiber bragg grating interrogator Pustakhod, D.; Kleijn, E.; Williams, K.A.; Leijtens, X.J.M.

Reconfigurable optical backbone network architecture for indoor wireless communication Mekonnen, K.A.; Tangdiongga, E.; Koonen, A.M.J.

Mode-locking and frequency beating in. compact semiconductor lasers. Michael J. Strain

Mode-locked lasers in InP photonic integrated circuits

Testing with Femtosecond Pulses

Document Version Publisher s PDF, also known as Version of Record (includes final page, issue and volume numbers)

Wavelength switching using multicavity semiconductor laser diodes

Record bandwidth and sub-picosecond pulses from a monolithically integrated mode-locked quantum well ring laser

Published in: Proceedings of the 20th Annual Symposium of the IEEE Photonics Benelux Chapter, November 2015, Brussels, Belgium

Simulation of semiconductor modelocked ring lasers with monolithically integrated pulse shaping elements

Active mode-locking of miniature fiber Fabry-Perot laser (FFPL) in a ring cavity

PHOTONIC INTEGRATED CIRCUITS FOR PHASED-ARRAY BEAMFORMING

A new picosecond Laser pulse generation method.

Introduction Fundamental of optical amplifiers Types of optical amplifiers

Designing for Femtosecond Pulses

Optical Fibers p. 1 Basic Concepts p. 1 Step-Index Fibers p. 2 Graded-Index Fibers p. 4 Design and Fabrication p. 6 Silica Fibers p.

Multi-wavelength laser generation with Bismuthbased Erbium-doped fiber

Multiwavelength Single-Longitudinal-Mode Ytterbium-Doped Fiber Laser. Citation IEEE Photon. Technol. Lett., 2013, v. 25, p.

Low Phase Noise Laser Synthesizer with Simple Configuration Adopting Phase Modulator and Fiber Bragg Gratings

A broadband fiber ring laser technique with stable and tunable signal-frequency operation

Timing Noise Measurement of High-Repetition-Rate Optical Pulses

3550 Aberdeen Ave SE, Kirtland AFB, NM 87117, USA ABSTRACT 1. INTRODUCTION

SUPPLEMENTARY INFORMATION

High-frequency tuning of high-powered DFB MOPA system with diffraction limited power up to 1.5W

IST IP NOBEL "Next generation Optical network for Broadband European Leadership"

Leaky-wave slot array antenna fed by a dual reflector system Ettorre, M.; Neto, A.; Gerini, G.; Maci, S.

Laser Diode. Photonic Network By Dr. M H Zaidi

Putting PICs in Products A Practical Guideline. Katarzyna Ławniczuk

PERFORMANCE OF PHOTODIGM S DBR SEMICONDUCTOR LASERS FOR PICOSECOND AND NANOSECOND PULSING APPLICATIONS

Two octaves bandwidth passive balun for the eleven feed for reflector antennas Zamanifekri, A.; Yang, J.

A continuous-wave Raman silicon laser

Published in: Proceedings of the 36th European Conference and Exhibition on Optical Communication, ECOC 2010, September 19-23, 2010, Torino, Italy

All-Optical Clock Division Using Period-one Oscillation of Optically Injected Semiconductor Laser

CMOS based terahertz instrumentation for imaging and spectroscopy Matters - Kammerer, M.

On-chip antenna integration for single-chip millimeterwave FMCW radars Adela, B.B.; Pual, P.T.M; Smolders, A.B.

3 General Principles of Operation of the S7500 Laser

Mechanism of intrinsic wavelength tuning and sideband asymmetry in a passively mode-locked soliton fiber ring laser

Planar circularly symmetric EBG's to improve the isolation of array elements Llombart, N.; Neto, A.; Gerini, G.; de Maagt, P.J.I.

Non resonant slots for wide band 1D scanning arrays

This is a paper submitted to and accepted for publication in:

Document Version Publisher s PDF, also known as Version of Record (includes final page, issue and volume numbers)

Heterogeneously Integrated Microwave Signal Generators with Narrow- Linewidth Lasers

Optical phase-locked loop for coherent transmission over 500 km using heterodyne detection with fiber lasers

High brightness semiconductor lasers M.L. Osowski, W. Hu, R.M. Lammert, T. Liu, Y. Ma, S.W. Oh, C. Panja, P.T. Rudy, T. Stakelon and J.E.

Vertical External Cavity Surface Emitting Laser

External-Cavity Tapered Semiconductor Ring Lasers

All-fiber, all-normal dispersion ytterbium ring oscillator

TIGER Femtosecond and Picosecond Ti:Sapphire Lasers. Customized systems with SESAM technology*

To generate a broadband light source by using mutually injection-locked Fabry-Perot laser diodes

Introduction Fundamentals of laser Types of lasers Semiconductor lasers

40 GHz Dual Mode-Locked Widely-Tunable Sampled-Grating DBR Laser

Yb-doped Mode-locked fiber laser based on NLPR Yan YOU

SUPPLEMENTARY INFORMATION

InP-based Waveguide Photodetector with Integrated Photon Multiplication

Cost-effective wavelength-tunable fiber laser using self-seeding Fabry-Perot laser diode

Optical Amplifiers (Chapter 6)

Optical Amplifiers Photonics and Integrated Optics (ELEC-E3240) Zhipei Sun Photonics Group Department of Micro- and Nanosciences Aalto University

Voltage dip detection with half cycle window RMS values and aggregation of short events Qin, Y.; Ye, G.; Cuk, V.; Cobben, J.F.G.

High bit-rate combined FSK/IM modulated optical signal generation by using GCSR tunable laser sources

Optical phase-coherent link between an optical atomic clock. and 1550 nm mode-locked lasers

The Development of a High Quality and a High Peak Power Pulsed Fiber Laser With a Flexible Tunability of the Pulse Width

R. J. Jones College of Optical Sciences OPTI 511L Fall 2017

Ring cavity tunable fiber laser with external transversely chirped Bragg grating

Suppression of Stimulated Brillouin Scattering

Novel Dual-mode locking semiconductor laser for millimetre-wave generation

S Optical Networks Course Lecture 2: Essential Building Blocks

Single mode EDF fiber laser using an ultra-narrow bandwidth tunable optical filter

Lecture 6 Fiber Optical Communication Lecture 6, Slide 1

Directional Sensing for Online PD Monitoring of MV Cables Wagenaars, P.; van der Wielen, P.C.J.M.; Wouters, P.A.A.F.; Steennis, E.F.

A 13.56MHz RFID system based on organic transponders

Single-longitudinal mode laser structure based on a very narrow filtering technique

Copyright 2014 Chinese Laser Press. Version: Published. Deposited on: 21 May 2015

Concepts for High Power Laser Diode Systems

DIAMOND-SHAPED SEMICONDUCTOR RING LASERS FOR ANALOG TO DIGITAL PHOTONIC CONVERTERS

RECENTLY, studies have begun that are designed to meet

taccor Optional features Overview Turn-key GHz femtosecond laser

Copyright 2006 Crosslight Software Inc. Analysis of Resonant-Cavity Light-Emitting Diodes

Basic concepts. Optical Sources (b) Optical Sources (a) Requirements for light sources (b) Requirements for light sources (a)

Calibration of current-steering D/A Converters

Spurious-Mode Suppression in Optoelectronic Oscillators

The Theta Laser A Low Noise Chirped Pulse Laser. Dimitrios Mandridis

A multi-band single-loop PLL frequency synthesizer with dynamically-controlled switched tuning VCO Samuel, A.M.; Pineda de Gyvez, J.

A 40 GHz, 770 fs regeneratively mode-locked erbium fiber laser operating

High Power AlGaInAs/InP Widely Wavelength Tunable Laser

A novel tunable diode laser using volume holographic gratings

A tunable and switchable single-longitudinalmode dual-wavelength fiber laser with a simple linear cavity

Lasers à fibres ns et ps de forte puissance. Francois SALIN EOLITE systems

Chapter 1 Introduction

Microwave Radiometer Linearity Measured by Simple Means

Tunable single frequency fiber laser based on FP-LD injection locking

Synchronization in Chaotic Vertical-Cavity Surface-Emitting Semiconductor Lasers

- no emitters/amplifiers available. - complex process - no CMOS-compatible

S-band gain-clamped grating-based erbiumdoped fiber amplifier by forward optical feedback technique

OPTICAL generation and distribution of millimeter-wave

Supplementary Figures

Self-organizing laser diode cavities with photorefractive nonlinear crystals

Optoelectronic Oscillator Topologies based on Resonant Tunneling Diode Fiber Optic Links

Transcription:

DBR based passively mode-locked 1.5m semiconductor laser with 9 nm tuning range Moskalenko, V.; Williams, K.A.; Bente, E.A.J.M. Published in: Proceedings of the 20th Annual Symposium of the IEEE Photonics Benelux Chapter, 26-27 November 2015, Brussels, Belgium Published: 01/01/2015 Document Version Publisher s PDF, also known as Version of Record (includes final page, issue and volume numbers) Please check the document version of this publication: A submitted manuscript is the author's version of the article upon submission and before peer-review. There can be important differences between the submitted version and the official published version of record. People interested in the research are advised to contact the author for the final version of the publication, or visit the DOI to the publisher's website. The final author version and the galley proof are versions of the publication after peer review. The final published version features the final layout of the paper including the volume, issue and page numbers. Link to publication Citation for published version (APA): Moskalenko, V., Williams, K. A., & Bente, E. A. J. M. (2015). DBR based passively mode-locked 1.5m semiconductor laser with 9 nm tuning range. In P. Kockaert, P. Emplit, S-P. Gorza, & S. Massar (Eds.), Proceedings of the 20th Annual Symposium of the IEEE Photonics Benelux Chapter, 26-27 November 2015, Brussels, Belgium (pp. 15-18). [1.A.4.] Brussels: OPERA-photonics, Brussels School of Engineering. General rights Copyright and moral rights for the publications made accessible in the public portal are retained by the authors and/or other copyright owners and it is a condition of accessing publications that users recognise and abide by the legal requirements associated with these rights. Users may download and print one copy of any publication from the public portal for the purpose of private study or research. You may not further distribute the material or use it for any profit-making activity or commercial gain You may freely distribute the URL identifying the publication in the public portal? Take down policy If you believe that this document breaches copyright please contact us providing details, and we will remove access to the work immediately and investigate your claim. Download date: 03. Nov. 2018

Proceedings Symposium IEEE Photonics Society Benelux, 2015, Brussels, Belgium DBR based passively mode-locked 1.5µm semiconductor laser with 9 nm tuning range V. Moskalenko, K. Williams, and E. Bente Technical University of Eindhoven, Dept. Electrical Engineering, Den Dolech 2, 5612 AZ Eindhoven, Netherlands We present the first tuneable DBR based extended cavity integrated passively modelocked laser realized in an anti-colliding design. The laser is realized as an InP based photonic integrated circuit. A detailed study of the laser performance under various operating conditions is presented. Tuning of the laser over 9nm using the DBR grating was achieved. We demonstrate that tuning of the optical spectrum towards increased absorption of the saturable absorber leads to an improvement of the mode-locked laser performance. A reduction of the fundamental RF linewidth and a reduction of the pulse length down to the Fourier-limit were observed. Introduction A semiconductor passively mode-locked laser (PML) is an attractive compact source for the generation of short optical pulses and coherent frequency combs. Especially an integrated semiconductor PML is of particular interest. It is a robust and small source which does not require either optical pumping or an RF source for producing periodic short pulses. Usually to achieve mode-locking a saturable absorber (SA) and semiconductor optical amplifier (SOA) should be combined in the laser cavity. In the case of an integrated PML the SA can be formed by reverse biasing a small section of the SOA. The SOA provides the optical gain which can be saturated when light of high intensity propagates through. Similarly the high intensity signal saturates the SA which recovers in the order of several ten of picoseconds. The combination of these two saturation processes leads to the appearance of a short time window of positive net gain, which causes pulsed operation of the laser. To obtain short optical pulses in a semiconductor laser an optimal spectral detuning between the SA and SOA spectra should be achieved. Both gain and absorption spectra vary with the operating conditions, which leads to the spectral variation of the output signal of a PML. Operating at different wavelength also influences the recovery processes in the SOA and SA. This also makes it difficult to accurately predict the operating wavelength. In order to solve this issue a distributed Bragg reflectors (DBR) can be used as a mirror in the linear PML. The use of a DBR grating in a PML allows for tuning of the optical spectrum by injecting current into DBR section. In this paper we present an integrated tuneable extended cavity PML operating at 1.55 µm. Moreover, we demonstrate an improvement of the performance in terms of RF linewidth and pulse duration when the PML is being tuned towards shorter wavelength. Device geometry The laser was designed using a library of predefined building blocks and layerstack in a multiproject wafer run of the Oclaro foundry for photonic integration. A DBR section of 50 % reflection centered at 1550 nm was used as an output coupler. A multimode 15

DBR based passively mode-locked 1.5 µm semiconductor laser with 9 nm tuning range interference reflector (MIR) served as an end mirror. The MIR was designed to provide 100 % reflection however fabrication imperfections cause a loss of less than 1 db [1]. Fig. 1. Sketch of the layout of the PML. As shown in Fig. 1 the cavity also includes three active sections (100 µm long SA1, 100 µm long SA2 and 2 mm long SOA) and 3 mm passive waveguide. The total length of the cavity is 5.5 mm. The laser configuration allows for repositioning of the SA either to the output coupler or to the end mirror depending on the bias applied on the SA1 and SA2. If the SA1 is reversely biased and SA2 is forward biased, the SA is placed next to the output coupler. Alternatively the SA is placed at the MIR by reversely biasing the SA2 and forwards biasing SA1. In both cases the long active section (SOA) has to be forward biased. Previously in [2] we used a laser layout very similar to the one presented here to show that positioning of the SA next to the low reflectance mirror leads to an improvement of the PML performance in terms of output power, stability and pulse duration. For this reason in this paper we will investigate the configuration where the SA is placed next to the DBR section. Tuneable mode-locked laser performance The chip with the PML was mounted on a copper chuck. Its temperature was stabilized at 18 C. Before going to the instruments the light was collected with an AR coated lensed fiber after which it went through an optical isolator. First, the DBR reflection spectrum was measured. It was obtained from measurements of the power of the signal from a tunable laser reflected from the DBR grating in the PML while SA1 and SOA were reversely biased. The reflection curve is shown in Fig. 2 (a). The maximum is scaled to 0.5. The DBR section was not contacted during this measurement. The reflection band is 4 nm wide and it is centered at 1551 nm, which is 1 nm higher than the design value. Even though the facet of the chip was AR coated, the raw experimental data had ripples with the period associated with the distance between the DBR and the facet at the end of the output waveguide. To obtain the reflection spectrum which is shown in Fig. 2 (a) the ripples were filtered out. The PML performance was characterized for a range of the SOA currents between 60 to 140 ma and applied voltages on the SA from -0.5 to -2.1 V. Fig. 2 (b) shows an optical spectrum of the PML measured using a 20 MHz spectrum analyzer at ISOA = 90 ma and USA=-1.3 V. The spectrum shows a frequency comb centered at 1554 nm with a mode separation of 7.4 GHz. It must be noted that the optical spectrum is asymmetrically shaped and its central wavelength is shifted from the top of the DBR reflection band towards longer wavelengths by 2.5 nm. We assume that a red shift of the PML optical spectrum is caused to the gain and absorption spectral dependency. Despite the fact, that the optical spectrum to a large extent is determined by the gain and absorption profile, tuning of the optical spectrum with the injecting current into DBR grating was achieved. 16

Proceedings Symposium IEEE Photonics Society Benelux, 2015, Brussels, Belgium Fig. 2. a) DBR reflection spectrum at IDBR = 0. b) Optical spectrum of the PML measured at ISOA = 90 ma and USA = -1.3 V. The tuning was investigated when the SOA current was set at 80 ma and a voltage of -1.1 V was applied on the SA. The performance of the PML under the tuning was evaluated through the measurements of output power, optical spectrum, beating signal generated in a fast photodetector and recording of autocorrelation traces. Since the laser output power was low, the signal was first amplified by a low noise erbium doped fiber amplifier (EDFA) and then sent through the polarization controller (PC) to the autocorrelator. Measurements of the output power showed that tuning of the DBR reflection band to shorter wavelength causes a decrease of the output power. The decrease of the output power can be explained by the increased small signal absorption in the SA at shorter wavelength. The change of the energy in SA and SOA section as well as spectral tuning are causing significant changes in PML performance. Fig. 3 shows the RF spectrum (a) and optical spectrum (b) for IDBR from 0 to 15 ma. As it can be noticed from these figures the current injection in the DBR section leads to a variation of the fundamental frequency in the order of 100 MHz and a 9 nm red shift of the optical spectrum. Fig. 3 (c) shows the dependency on IDBR of the wavelength of the maximum of optical spectrum. Moreover, an improvement of the PML performance was observed while the DBR was tuned. Fig. 3 (d) shows a decrease of the 10 db RF linewidth down to 200 khz, which is lower than the minimum RF linewidth value (290 khz) observed without applying current in the DBR. The tuning of the optical spectrum also leads to the narrowing of the AC trace width from 10 ps to 3.95 ps. The narrowest AC trace measured at IDBR = 19 ma and together with a fit to a Gaussian function is shown in Fig. 3 (f). The optical spectrum which corresponds to this AC trace is shown in Fig. 3 (g). At these conditions the pulse width is 2.55 ps and optical spectrum has a width of 1.7 nm. It means that a time bandwidth product of 0.46 is achieved. This improvement in the PML performance can be explained by a wavelength dependency of the dynamics of the absorption. When shifting towards the higher energy side the SA absorber exhibits higher absorption and a faster recovery time. This leads to the decrease of the temporal window of positive gain and reduces the noise at the trailing edge of the pulse. In summary, the first tuneable integrated passively mode-locked laser realized in anticolliding pulse mode-locking configuration was demonstrated. A tuning range of 9 nm was achieved, which to our knowledge the largest tuning range is observed in an integrated PML. A significant improvement of the PML performance in terms of pulse 17

DBR based passively mode-locked 1.5 µm semiconductor laser with 9 nm tuning range width and RF linewidth was observed when tuning the optical spectrum towards shorter wavelength. Fig. 3. a) RF spectra and b) optical spectra recorded for the range of IDBR from 0 to 15 ma. c) Dependency of the wavelength of optical spectrum maximum on IDBR. RF linewidth (d) and AC width (e) as a function of IDBR. f) AC trace fitted measured at IDBR =19 ma. The experimental data (blue circles) fitted by sech 2 (red line). g) Optical spectrum recorded at IDBR =19 ma. All the results were obtained at ISOA = 80 ma and USA = -1.1 V. The research leading to these results has received funding from European Community s Seventh Framework Program FP7/2007-2013 under grant agreement 257210 PARADIGM. References [1] E. Kleijn, M. K. Smit, and X. J. M. Leijtens, Multimode Interference Reflectors: A New Class of Components for Photonic Integrated Circuits, J. Light. Technol., vol. 31, no. 18, pp. 3055 3063, Sep. 2013. [2] V. Moskalenko, K. A. Williams, and E. A. J. M. Bente, Integrated extended-cavity 1.5 #x00b5;m semiconductor laser switchable between self and anti-colliding pulse passive mode-locking configuration, IEEE J. Sel. Top. Quantum Electron., vol. PP, no. 99, pp. 1 1, 2015. 18