Are you ready to play with wool? It s too fun! First, you gather together everything you need. Your wool needs to be felted. To felt your wool, soak it in a sink of really hot water or run it thru a cycle of hot water in your washing machine, then rinse in cold water. Dry it in your dryer till it s good and dry. (Wash or soak like colors together so they don t bleed.) Felting makes your wool all soft and yummy and keeps it from fraying as you work with it. (If you don t know if your wool is felted, you can always felt it again to be sure. It won t hurt it to felt it again.) Then you need your paper backed fusible web. I ve used heat n bond, wonder under, steam a seam, and soft fuse. They all work fine, but soft fuse is my most favorite. It s lite, adheres really well, and I like it the best. But they all work fine. When you are ready to trace your pattern, make sure that the image has been reversed first. If it s been reversed already, the pattern usually says so. If it hasn t been reversed, then you need to use a window or a light box and trace from the back of the pattern. Place your fusible web, paper side up, over your pattern, and trace your pattern pieces. Leave 1/8 to 1/4 space between each traced shape. If any shapes on your pattern overlap, you need to trace them seperately don t overlap your tracing! Label all your
shapes. If you have pieces that are small and should all be one color of wool (like the sheep feet, ear, face, and tail), trace them close together. After you are done tracing, cut out each shape JUST OUTSIDE the drawn line. See how there is a little space around each shape? Do that. Since the little black sheep pieces are very small, I just cut them out all together in one big chunk.
Lay your traced shapes, paper side up, on the correct color of wool. Be frugal with your spacing. If you have many traced pieces on one color of wool (such as flower petals), place them close together. Press with your iron for 5 or so seconds. After it s cooled a bit, check the edges and press for another couple of seconds if you need to.
After you have fused all of your paper shapes onto the wool, cut out the shapes DIRECTLY ON the line. Cut out all of your wool shapes. (This is a good time to sit in front of a movie.)
When you re done cutting out your wool pieces you ll have little scraps like these. Unless they are incredibly teeny tiny, I save them. Wool is not cheap, and you d be surprised what you can do with little scraps.
After your wool has cooled, peel off the paper backing. I throw those away. (I m frugal, not crazy.) Following your pattern, diagram, or picture, lay out your pieces. I like to lay out everything all at once, even if there are layers. Some people like to press layer by layer, but I don t. There is nothing worse than pressing some pieces down, then realizing that
something should have been placed under something else. (Believe me.) But, if you like to layer, you go right ahead. Whatever makes you happy. Be sure to leave enough room around the outside of your block to allow for your 1/4 seam allowance. After you have placed all your pieces and you are happy with how they look, you can press them down. Very carefully, so as not to move anything, lay your iron down on the pieces and hold it there for 8-10 seconds. Gently move your iron around to fuse all the pieces.
Use lots of steam, baby, lots of steam. Just steam the heck out of it. Don t hold your iron down in one place for too long though, because it is possible to burn your wool! Better to do lots of little pressing motions than one big long burning pressing motion. See my steam?
When everything is fused, turn your block over and steam it from the back. (I just realized you can sort of see my reflection in the iron. Good thing I got out of my jammies.)
After your block has cooled, you can use your favorite marking tool to draw the flower stems.
And look at that! You have yourself a block!
Stitches: How To Do Blanket Stitch: Sewing In From The Edge Beginning Your Stitches: Photo A: Thread your needle and knot the tail end. Start by sending your needle up from the back (#1 in photo A) at the bottom edge of the piece you ll be sewing down. Start your first stitch by poking the needle down to the back (#2 in photo A) about 1/4" away from where the thread first came up and about 1/4" up from the edge. Photo B: To complete your first stitch, poke your needle from the back to the front (#3 in photo B). This should be straight down from #2 in the photo. It should also be right at the bottom edge of the piece you are sewing down. Before pulling this stitch tight, send your needle through the loop of thread, or as photos B and C show, make sure your thread stays under your needle.
Photo C: This photo shows you making the second stitch. #1 on this photo was #3 on photo B. Continue each stitch like this and you are on your way. Now you know how to do blanket stitch when sewing in from the edge. When You Run Out of Thread: Photo A: Poke the needle down as if you were starting another stitch. Pull the thread all the way through, but don't pull it tight yet. Leave enough of a loop, and only enough, so that later with your new piece of thread you can catch this loop and then pull that stitch tight into
place. So to determine how loose to leave this last stitch before the knot, just lay the loose loop of thread across as if you had properly finished the stitch. Cut your thread and knot it off with the knot tight against the felt so your loose loop of thread stays the length you want it. Photo B: Now thread your needle and knot the tail end. Now just like when you started your project, poke your needle up from the back (#3 in photo B) at the bottom edge. To complete this stitch, slide your needle under the loose loop you left and then pull your stitch tight into place. Photo C: This photo shows that your thread has been changed and you are on your way again.
To End Your Stitches: Photo A: Poke your needle down to the back, on the right side of your last stitch. Then knot off your thread. How To Do Blanket Stitch:
Sewing Corners Doing corners is pretty easy. To go around a corner, just poke your needle down diagonally across from the corner. These three stitches could all meet in the same hole in the felt, or they don't need to (as we have shown). It is just personal preference.