ASSEMLY INSTRUTIONS ITEM NO. D435-60S MILO RETANGLE DINING TALE MILO DINING HAIR (SET INLUDES 4 HAIRS, ENH) This page lists all the contents included in the ox. Please take time to identify the hardware as well as the individual components to this product. As you unpack and prepare for assembly, place the contents on a carpeted or padded area to protect them from damage. l e a n i n g & a r e Treat the surface with care, clean it with a dry or damp soft cloth. Do not use abrasive cleaners. Hardware may be loosen over time. Periodically check that all connections are tight. A Phillips screwdriver is necessary for assembly.
GENERAL INFORMATION, TIPS & TRIKS. Please read the assembly instructions prior to assembling this product.. To avoid damages, assemble this product on a non-abrasive surface such as a carpet. 3. Make sure all bolts and nuts are tightly fastened before the product is used. 4. Not for commercial use. 5. are: Wipe with a damp cloth. Use furniture polish or lemon oil on the wood as needed. Avoid prolonged exposure to moisture. Please make sure you have all parts before beginning assembly. Please wait until all steps are completed before tightening bolts. We recommend two people to assemble. A Phillips screwdriver is necessary for assembly. Do not put hot pots or objects which are more than 80 degrees Fahrenheit directly on the table.
TALE PART LIST A. Table Top. Table Legs QTY: P QTY: 4 PS TALE HARDWARE LIST. FLAT WASHERS. SPRING WASHERS 3. NUTS 4. ALLEN WRENH QTY: P 3
STEP TALE ASSEMLY INSTRUTIONS Turn the Table Top (A) upside down on a non-abrasive surface such as a carpet (the underside of the Table Top (A) should be placed face up). Attach the Table Legs () to the corner of the apron of the Table Top (A) by using Flat Washers (), Spring Washers (), Nuts (3), and tighten with Allen Wrench (4) as per illustration below. 4 A 4
TALE ASSEMLY INSTRUTIONS STEP Turn the table to the upright position carefully. Make sure the table is level, and then securely tighten all nuts at this stage. Assembly is completed. The table is now ready for use. 5
HAIR PART LIST A. ack Legs. Seat Frames. Front Legs D. ushion Seats QTY: 4 PS QTY: 4 PS QTY: 4 PS HAIR HARDWARE LIST. FLAT WASHERS. SPRING WASHERS 3. NUTS 4. ALLEN WRENH QTY: 44 PS QTY: 44 PS QTY: 6 PS QTY: P 5. SHORT OLTS 6. LONG OLTS 7. WOOD SREWS SIZE: /4" x 3/4" SIZE: /4" x 3" SIZE: 5/3" x /" QT Y : P S QTY: 6 PS QT Y : 4 P S 6
STEP HAIR ASSEMLY INSTRUTIONS Attach the Front Legs () to the Seat Frame () by using Nuts (3), Spring Washers (), and Flat Washers (). Note: The Seat Frame () has two screw holes on each side, which are used for attaching the seat. These holes are wider on the bottom and narrower on the top. Ensure the wider holes face towards you. 4 3 3 PLASTI PLUG. 3 STEP Attach the Seat Frame () to the ack Leg (A) by using Short olts (5), Long olts (6), Spring Washers (), and Flat Washers (). Do not fully tighten. Turn the chair upright. Make sure the assembled unit is level and square. Tightly fasten all Nuts (3) and olts (5&6) with the Allen Wrench (4). A 4 6 5 7
HAIR ASSEMLY INSTRUTIONS STEP 3 Place the ushion Seat (D) upside down on a non-abrasive table surface. The rear (tapered end) of the ushion Seat (D) should be near the table edge. Hint: Protect the non-abrasive table surface and the ushion Seat (D) by laying a towel in-between the chair seat and table. Place the assembled chair frame on the ushion Seat (D). Attach with Wood Screws (7). Tighten the screws. 7 7 7 7 7 7 D A 8
HAIR ASSEMLY INSTRUTIONS STEP 4 The Dining hair is now ready for use. Repeat Steps to 3 to assemble the other chairs. Printed in Vietnam 9
ENH PART LIST A. ushion Seat. Front Legs. Seat Frame QTY: P QTY: 4 PS QTY: P ENH HARDWARE LIST. FLAT WASHERS. SPRING WASHERS 3. NUTS 4. ALLEN WRENH QTY: P 5. WOOD SREWS SIZE: #8 x /" L 0
STEP ENH ASSEMLY INSTRUTIONS Attach the Front Legs () to the Seat Frame () by using Nuts (3), Spring Washers (), and Flat Washers (). Note: The Seat Frame () has two screw holes on each side, which are used for attaching the seat. These holes are wider on the bottom and narrower on the top. Ensure the wider holes face towards you. 4 3 3 STEP Place the ushion seat (A) upside down on a non-abrasive table surface. The rear (tapered end) of the ushion Seat (A) should be near the table edge. Hint: Protect the non-abrasive table surface and the cushion seat (A) by laying a towel in-between the chair seat and table. Place the assembled bench frame on the ushion Seat (A). Attach with Wood Screws (5). Tighten the screws. 5 A
ENH ASSEMLY INSTRUTIONS STEP 4 The bench is now completed and ready for use. Printed in Vietnam