All All legal legal rights rights in this in this document are are the the exclusive property of of and and no no part part of of it may it may be be reproduced or or communicated to to any any other other party party without our our authorization. All All data data in in this catalogue is for reference only and may be changed without notice, in line with our policy of continuous technical development. MOBISTAT Mobile Radio Stations h e l p i n g w o r d s t o f l y ISO 9001 SGS
MOBISTAT Flanged Pole Mobile stations with flanged pole are antenna supporting structures which are used mostly in temporary radio base stations for cellular networks. This type of solution allows fast and easy installation, also in restricted areas. GENERAL DESCRIPTION The SUPPORTING STRUCTURE consists of a trailer, approved for road use, onto which a frame with four telescopic stabilisers is fitted and, only for the compact version, a rectangular extension, supported by two additional feet. The pole, which is fixed to the frame, consists of cylindrical sections and is anchored to the support feet by means of two or three sets of guys. The structure, complete with ballast weights and working platform in metal grating, can be converted into a permanent station simply by replacing the end part of the four stabilisers. The CLIMBING LADDERS are of the type with T rail safety climb system, with top and bottom stops, complete with intermediate tiltable footrest every 8-9 m. An anti-climb device is supplied to prevent access by unauthorized persons. The VERTICAL CABLE TRAY consists of suitably shaped, L-section members, bolted to the pole sections at 500/1000 mm intervals and positioned next to the climbing ladder down the whole length of the pole. This system ensures excellent fixing of the cables and feeders. The GROUNDING PROTECTION consists of a set of copperplated ground plates, connected to each other, and a copper conductor running down the side of the pole. In addition, special busbars are supplied for connection to grounding kits (art. KTF...). The system ensures equipotentiality of the structure. The AIRCRAFT WARNING LIGHT SYSTEMS both conform to ICAO or FAA Standards. For day-time warning, the top third of the pole is painted red and white. The night-time warning system comprises a signalling unit with steady or flashing red beacons. The ANTENNA MOUNTS, in hot-dip galvanized steel, consists of a 3.0 m high pipe mount complete with brackets (art. TAPB.) for 3 panel antennas. The above poles can also, on request, be fitted with universal pipe brackets for dish antennas (art. TAMA...). TECHNICAL SPECIFICATIONS DESIGN AND STANDARDS Design follows the most modern measuring criteria, with the aid of advanced software systems. Structural analysis, static and dynamic tests conform to the most recent United States (EIA 222) and Italian (CNR-UNI) Standards. Tests to other International Standards (EURONORM, BS, NV65, etc.) can be carried out on request. WIND LOADS The radio base station with flanged pole can withstand a maximum equivalent surface area of antennas of 1.8 m 2 at the top, corresponding to 3 panel antennas (H = 2 m) and 2 dish antennas (Ø 60 cm). Tests are in accordance with the requirements of Standards EIA 222: basic wind speed equivalent to 100 mph (160 km/h). The structures are also tested in accordance with Italian Standards for the various wind zones specified in D.M. (Ministerial Decree) of 16/01/96, with the operating limits indicated in the installation, use and maintenance manual. TWIST & SWAY Maximum twist and sway at the top of the flanged pole, with a constant wind speed of 100 km/h, is less than 50'. GALVANIZATION All materials are protected by hot-dip galvanizing, in accordance with ASTM A123 and Euronorm EN 1461 Standards. MATERIALS The materials used comply with the requirements of European Standards (Euronorm): Structural parts: S355JR (Fe 510 B) EN 10025 S235JR (Fe 360 B) EN 10025 Nuts and bolts: type 6.8. EN 20898-1 STANDARD VERSION The mobile station with flanged pole is available in two different versions, having the following characteristics: version A ultra compact This version is for use in locations where space is very limited and where the equipment can be contained in cabinets or inside a mini-shelter. Dimensions: - maximum height from ground = 26.0 m - plan dimensions = 5.1 x 5.1 m (in working position) - weight of mobile station, excluding ballast = 4900 kg - weight of ballast = 6300 kg. version B compact This version is the best solution for replacing a fixed station since it can reach greater heights and allows equipment to be All legal rights in this document are the exclusive property of and no part of it may be reproduced or communicated to any other party without our authorization. All data in this catalogue is for reference only and may be changed without notice, in line with our policy of continuous technical development. - tel. +39 0432 84381 fax +39 0432 848997 www..it @.it - Catalogue 2004 - page 110
MOBISTAT Flanged Pole All legal rights in this document are the exclusive property of and no part of it may be reproduced or communicated to any other party without our authorization. All data in this catalogue is for reference only and may be changed without notice, in line with our policy of continuous technical development. housed in a shelter the same size as those used for traditional sites. Dimensions: - maximum height from ground = 30.0 m - plan dimensions = 5.6 x 8.2 m (in working position) - weight of mobile station, excluding ballast = 5500 kg - weight of ballast = 6500 kg. CATALOGUE PRODUCTS STANDARD SUPPLY Provides the minimum configuration required for commissioning of the MOBISTAT flanged pole, excluding radiant systems and their mounts. Standard supply includes: trailer approved for road use antenna support pole consisting of steel tube, in sections, with a maximum length of 6 m each base frame consisting of steel section members with removable feet, fixed to the road trailer antenna pipe mount complete with brackets for 3 panel antennas platform in metal grating and shelter support climbing ladder with footrests safety parapets in hot-dip galvanized steel access ladder to working platform in hot-dip galvanized steel mains supply box (for electricity supply meter) vertical fixing system for feeders and service cables guys consisting of galvanized steel cables with relative tensioners ballast weights installation, use and maintenance manual. ACCESSORIES These parts are additional to those provided in the basic versions and must be ordered separately: grounding kit comprising 5 copper-plated steel rods, 1500 mm long and 40 m of bare copper conductor (cross sectional area 50 mm 2 ), complete with all necessary clamps and busbars (art. GRPI) mounts for dish antennas (art. TAMA...) aircraft warning lights, night-time obstruction light (art. S...) red/white paintwork for top third of tower, day-time obstruction warning - art. SOVD shelter for mobile radio equipment electrical control panel (art. MECP) mesh fencing generating set (art. MGES...) upgrade for permanent station. "ultra compact" art. MFUC... A Article MFUC 2051 MFUC 2351 MFUC 2651 MFCO 2456 MFCO 2756 MFCO 3056 H A Height H m 20.0 23.0 26.0 24.0 27.0 30.0 "compact" art. MFCO... A B shelter Base dimensions A B m m km/h 5.1 5.1 5.1 5.6 5.6 5.6 / / / 8.2 8.2 8.2 Max wind speed 160 160 160 160 160 160 - tel. +39 0432 84381 fax +39 0432 848997 www..it @.it - Catalogue 2004 - page 111
MOBISTAT Flanged Pole aircraft warning light system panel antennas dish antennas cable fixing every 500/1000 mm outdoor cabinet fencing stabilisers antenna mount FLANGED POLE ladder with safety climb system and footrests guys guy tensioner grounding All legal rights in this document are the exclusive property of and no part of it may be reproduced or communicated to any other party without our authorization. All data in this catalogue is for reference only and may be changed without notice, in line with our policy of continuous technical development. - tel. +39 0432 84381 fax +39 0432 848997 www..it @.it - Catalogue 2004 - page 112
All legal rights in this document are the exclusive property of and no part of it may be reproduced or communicated to any other party without our authorization. All data in this catalogue is for reference only and may be changed without notice, in line with our policy of continuous technical development.
MOBISTAT Self Mounting Pole Mobile stations with self mounting telescopic pole are antenna supporting structures which allow fast and easy installation and are used mostly for temporary radio base stations and for emergency networks where the use of cranes is difficult. GENERAL DESCRIPTION The two-axle TRAILER for transporting the equipment consists of a supporting frame with a flatbed, made up of tubular components and electro-welded sheet metal; the whole assembly is hot-dip galvanized. It is equipped with: automatic reverse parking brake with pushbutton release lighting equipment with rear lights conforming to the latest EEC directives independent suspension on each of the four wheels, with torsion bar. The trailer is approved for a total load of 3500 kg. The pole SUPPORTING STRUCTURE consists of tubular sections, sized to withstand the loads generated by wind acting on the pole. This structure, which is fixed to the trailer, is fitted with four telescopic stabiliser feet which are extended when the pole is installed. The guys and ballast weights are secured to the ends of these feet. The entire frame is made of steel, protected by hot-dip galvanizing. The TELESCOPIC ALUMINIUM POLE comprises three tubular sections which slide into each other. Installation can be carried out simply by using the manual winches supplied with the station. These winches are used both to raise the pole from the horizontal to the vertical position and to extend the individual segments to their maximum height. The UPGRADE KIT enables the mobile station to be converted into a fixed station because all the structural parts have been sized to withstand the design loads of a permanent station. The kit consists of four components designed to replace the adjusting screws on the structure feet. These supports are buried in a single block of concrete in order to secure the station to the ground. The GROUNDING PROTECTION consists of a set of copperplated ground plates, connected to each other, and a copper conductor running down the side of the pole. The system ensures equipotentiality of the structure. The AIRCRAFT WARNING LIGHT SYSTEMS both conform to ICAO or FAA Standards. For day-time warning, the top third of the pole is painted red and white. The night-time warning system comprises a signalling unit with steady or flashing red beacons. The ANTENNA MOUNTS, in hot-dip galvanized steel, consist of a 3.5 m high pipe mount complete with brackets (art. TAPB.) for 3 panel antennas. The above pipe mounts can also, on request, be fitted with universal pipe brackets for dish antennas (art. TAMA). TECHNICAL SPECIFICATIONS GENERAL DATA Weight of the station in transport condition: 2650 kg Maximum weight which can be transported (cabinets and accessories): 850 kg Weight of ballast: 1600 kg Dimensions in transport condition (bxlxh): 5.0 x 2.4 x 3.9 m Surface area in operating condition: 5.2 x 5.2 m Maximum height from ground: 18.0 20.0 m Max. dimensions of equipment cabinet: 2.35 x 1.15 x 1.80 m Average installation time: 3 hours DESIGN AND STANDARDS Design follows the most modern measuring criteria, with the aid of advanced software systems. Structural analysis, static and dynamic tests conform to the most recent United States (EIA 222) and Italian (CNR-UNI) Standards. Tests to other International Standards (EURONORM, BS, NV65, etc.) can be carried out on request. WIND LOADS The radio base station with telescopic aluminium pole can withstand a maximum equivalent surface area of antennas of 1.3 m 2 at the top, corresponding to 3 panel antennas (H = 2.0 m) and 2 x Ø 30 cm dish antennas or to 3 panel antennas (H = 1.3 m) and 2 x Ø 60 cm dish antennas. Tests are in accordance with Eurocode requirements (Wind speed = 130 km/h). The structures are also tested in accordance with Italian Standards for the various wind zones specified in D.M. (Ministerial Decree) of 16/01/96, with the operating limits indicated in the installation, use and maintenance manual. TWIST & SWAY Maximum twist and sway, with a constant wind speed of 100 km/h, is less than 1 at the top of the pole and less than 0.5 at the upper attachment points for the guys (dish antenna fixing point). GALVANIZATION All materials are protected by hot-dip galvanizing in accordance with ASTM A123 and Euronorm EN 1461 Standards. MATERIALS The materials comply with the requirements of European All legal rights in this document are the exclusive property of and no part of it may be reproduced or communicated to any other party without our authorization. All data in this catalogue is for reference only and may be changed without notice, in line with our policy of continuous technical development. - tel. +39 0432 84381 fax +39 0432 848997 www..it @.it - Catalogue 2004 - page 114
MOBISTAT Self Mounting Pole All legal rights in this document are the exclusive property of and no part of it may be reproduced or communicated to any other party without our authorization. All data in this catalogue is for reference only and may be changed without notice, in line with our policy of continuous technical development. Standards (Euronorm). STEEL Frame and trailer: S235JR (Fe 360 B) EN 10025 Nuts and bolts: type 6.8. EN 20898-1 ALUMINIUM Telescopic pole: alloy P-AI Mg Si 6060 UNI 9006 NUTS AND BOLTS: CATALOGUE PRODUCTS Article MTUC 1852 MTUC 2052 Height H m 18.0 20.0 A m 5.2 5.2 type 6.8. EN 20898-1 or stainless steel class A2-70. STANDARD SUPPLY Provides the minimum configuration required for commissioning of the station, excluding radiant systems and their mounts. Standard supply includes: trailer approved for road use aluminium antenna support pole base frame with telescopic feet working platform in checkered plate antenna pipe mount complete with brackets for 3 panel antennas safety parapets access ladder to the trailer working platform ladder with safety climb system mains supply box (for electricity supply meter) guys consisting of galvanized steel cables with relative tensioners installation, use and maintenance manual. ACCESSORIES These parts are additional to those provided in the basic versions and must be ordered separately: grounding kit comprising 5 copper-plated steel rods, 1500 mm long and 40 m of bare copper conductor (cross sectional area 50 mm 2 ), complete with all necessary clamps and busbars (art. GRPI) brackets for dish antennas (art. TAMA...) aircraft warning lights, night-time obstruction light (art. S...) red/white paintwork for top third of pole, day-time obstruction warning (art. SOVD) electrical control panel (art. MECP) generating set (art. MGES...) outdoor cabinet upgrade for permanent station. Dimensions B m 2.4 2.4 C m 4.8 4.8 Max wind speed km/h 130 130 H A B Working position outdoor cabinet Lifting phase Transport position C A 3.9 m - tel. +39 0432 84381 fax +39 0432 848997 www..it @.it - Catalogue 2004 - page 115
MOBISTAT Self Mounting Pole aircraft warning light system panel antennas dish antennas ladder with safety climb system fencing guy tensioner stabilisers antenna mount SELF-MOUNTING TELESCOPIC POLE guys outdoor cabinet grounding All legal rights in this document are the exclusive property of and no part of it may be reproduced or communicated to any other party without our authorization. All data in this catalogue is for reference only and may be changed without notice, in line with our policy of continuous technical development. - tel. +39 0432 84381 fax +39 0432 848997 www..it @.it - Catalogue 2004 - page 116
All legal rights in this document are the exclusive property of and no part of it may be reproduced or communicated to any other party without our authorization. All data in this catalogue is for reference only and may be changed without notice, in line with our policy of continuous technical development.
MOBISTAT Self Mounting Towers Self mounting mobile towers are antenna supporting structures, used mostly in temporary radio base stations for cellular networks. This type of solution allows fast and easy installation, also in restricted areas. The BORA 1750 self mounting tower is available in three versions to satisfy various needs, according to the required antenna loads. GENERAL DESCRIPTION The SUPPORTING STRUCTURE consists of a base onto which is mounted a self mounting square section lattice tower, which can pivot from the horizontal rest position to the vertical position and then be fully extended. A rotating support, to which the antenna pipe mount is secured, is fitted at the top of the tower. All versions are equipped with attachment points for guys and with four reinforcing struts. The structure of the mobile lattice tower is made entirely of steel, protected by hot-dip galvanizing. The tower bears the CE mark, indicating conformity with Directive 89/392/EEC and subsequent modifications. The VERTICAL CABLE TRAY is made of Ø 20 mm galvanized rungs (art. FPZ...) which are fitted to the tower during the lifting phase, at 500 mm intervals. This system firmly secures the cables and feeders. The GROUNDING PROTECTION consists of a set of copperplated ground plates, connected to each other, and a copper conductor running down the side of the tower. In addition, special busbars are supplied for connection to grounding kits (art. KTF..). The system ensures equipotentiality of the structure. The AIRCRAFT WARNING LIGHT SYSTEMS both conform to ICAO or FAA Standards. For day-time warning, the top third of the tower is painted red and white. The night-time warning system comprises a signalling unit with steady or flashing red beacons. The ANTENNA MOUNTS, in hot-dip galvanized steel, are designed to support different radiant systems. Two different types of antenna mount can be installed on BORA 1750 self mounting towers: pipe mount, 3.5 m high, complete with brackets (art. TAPB.) for 3 panel antennas pipe mount, 6.0 m high, complete with brackets (art. TAPB.) for 3 panel antennas. The above pipe mounts can also, on request, be fitted with universal pipe brackets for dish antennas (art. TAMA...). TECHNICAL SPECIFICATIONS GENERAL DATA Weight of tower in transport position (1) : 3800 kg Total weight of standard ballast weights for guys: 5200 kg Dimensions of tower in transport position: 5.8 x 1.5 x 1.9 m Supply voltage: 220 V 50 Hz Lifting hoist motor power: Maximum power drawn: Installation time: 1.7 kw 6.0 kw 2.0 h DESIGN AND STANDARDS Design follows the most modern measuring criteria, with the aid of advanced software systems. Structural analysis and static tests conform to the most recent European (Eurocodes 1 and 3) and Italian (CNR-UNI) Standards. Tests to other International Standards (EIA, BS, etc.) can be carried out on request. WIND LOADS The BORA 1750 self mounting tower can withstand a maximum equivalent surface area of antennas of 1.8 m 2 at the top. Tests are in accordance with Eurocode requirements (Wind speed = 130-160 km/h). The structures are also tested in accordance with Italian Standards for the various wind zones specified in D.M. (Ministerial Decree) of 16/01/96, with the operating limits indicated in the installation, use and maintenance manual. TWIST & SWAY Maximum twist and sway at the top of the self mounting tower, with a constant wind speed of 100 km/h, is less than 0.5 (30'). MATERIALS The materials comply with the requirements of European Standards (Euronorm): Structural parts: S235JR (Fe 360 B) EN 10025 Nuts and bolts: type 6.8. EN 20898-1 GALVANIZATION All materials are protected by hot-dip galvanizing in accordance with ASTM A123 and Euronorm EN 1461 Standards. STANDARD VERSIONS The BORA 1750 self mounting tower is available in three different versions, with the following characteristics: version A without guys maximum height from ground = 20.5 m maximum wind speed in working position (2) = 130 km/h plan dimensions = 3.9 x 3.9 m (in working position) version B with guys maximum height from ground = 20.5 m maximum wind speed in working position (2) = 160 km/h plan dimensions = 7.3 x 7.3 m (in working position) All legal rights in this document are the exclusive property of and no part of it may be reproduced or communicated to any other party without our authorization. All data in this catalogue is for reference only and may be changed without notice, in line with our policy of continuous technical development. - tel. +39 0432 84381 fax +39 0432 848997 www..it @.it - Catalogue 2004 - page 118
MOBISTAT Self Mounting Towers All legal rights in this document are the exclusive property of and no part of it may be reproduced or communicated to any other party without our authorization. All data in this catalogue is for reference only and may be changed without notice, in line with our policy of continuous technical development. version C with guys maximum height from ground = 23.0 m maximum wind speed in working position (2) = 160 km/h plan dimensions = 7.3 x 7.3 m (in working position) NOTES: (1) Value including weight of fixed concrete ballast weights mounted on the tower. (2) Values with use of additional ballast weights. CATALOGUE PRODUCTS STANDARD SUPPLY Provides the minimum configuration for commissioning of the tower, excluding radiant systems. Standard versions include: self mounting tower complete with base plates and reinforcement vertical cable tray system for feeders and service cables antenna pipe mount complete with brackets for 3 panel antennas galvanized steel guys with tensioners (for versions B and C only) standard ballast weights for guys (for versions B and C only) CE declaration of conformity installation, use and maintenance manual. ACCESSORIES These parts are additional to those provided in the basic versions and must be ordered separately: grounding kit comprising 5 copper plated steel rods, 1500 mm long and 40 m of bare copper conductor (cross sectional area 50 mm 2 ), complete with all necessary clamps and busbars (art. GRPI) mounts for dish antennas (art. TAMA...) additional ballast weights (art. ASBB) aircraft warning lights, night-time obstruction light (art. S...) red/white paintwork for top third of tower, day-time obstruction warning (art. SOVD). Article BORA 1750 A BORA 1750 B BORA 1750 C Height Base dimensions Max wind speed H A B m m m km/h 20.5 20.5 23.0 3.9 3.9 3.9 / 7.3 7.3 130 160 160 Guys not included included included H A B Working position Lifting phase 5.8 m Transport position 1.9 m A B - tel. +39 0432 84381 fax +39 0432 848997 www..it @.it - Catalogue 2004 - page 119
MOBISTAT Self Mounting Towers aircraft warning light system panel antennas antenna mount reinforcing struts base plate ballast weights dish antennas rotation system for azimuth orientation of the antennas SELF MOUNTING TOWER guys grounding tensioner All legal rights in this document are the exclusive property of and no part of it may be reproduced or communicated to any other party without our authorization. All data in this catalogue is for reference only and may be changed without notice, in line with our policy of continuous technical development. - tel. +39 0432 84381 fax +39 0432 848997 www..it @.it - Catalogue 2004 - page 120
All legal rights in this document are the exclusive property of and no part of it may be reproduced or communicated to any other party without our authorization. All data in this catalogue is for reference only and may be changed without notice, in line with our policy of continuous technical development.
MOBISTAT Trailer Semi-trailer mobile stations with self-mounting telescopic towers are antenna supporting structures which allow fast and easy installation and are used mostly for temporary radio base stations and for emergency networks. They are available in two different heights, according to the required antenna loads. GENERAL DESCRIPTION The SEMI-TRAILER consists of a supporting frame with steel longitudinal and cross members and a working platform in checkered plate. It is equipped with: axles with 15'' wheels and pneumatic shock absorbers braking system conforming to European Standards 24 V electrical system, electrical and compressed air connectors independent and adjustable parking stands. The square section SELF MOUNTING LATTICE TOWER can be raised from the horizontal rest position to the vertical position and then extended to its full height. At the top of the tower there is a swivelling bracket to which the antenna mount is fixed. All versions are equipped with attachment points for the guys and with four reinforcing struts. The entire structure of the mobile tower is in steel, protected by hot-dip galvanizing. The VERTICAL CABLE TRAY consists of Ø 20 mm rungs in galvanized steel (art. FPZ...) that are secured to the tower uprights during the lifting phase at intervals of approx. 500 mm. This system firmly secures the cables and feeders to protect them from damage due to vibration and distortion. The SHELTER consists of a steel frame and aluminium sheets. It is supplied complete with: main electrical panel and control panel power station with battery rack lighting equipment air conditioning system. The ANTENNA MOUNTS, in hot-dip galvanized steel, are designed for different radiating systems. Two different types of antenna pipe mounts can be mounted on the tower: 3.5 m high pole complete with brackets (art. TAPB.) for 3 panel antennas 6.0 m high pole complete with brackets (art. TAPB.) for 3 panel antennas. The above pipe mounts can also, on request, be fitted with universal pipe brackets for dish antennas (art. TAMA...). The AIRCRAFT WARNING LIGHT SYSTEMS both conform to ICAO or FAA Standards. For day-time warning, the top third of the tower is painted red and white. The night-time warning system comprises a signalling unit with steady or flashing red beacons. The GROUNDING PROTECTION consists of a set of copperplated ground plates, connected to each other and a copper conductor running down the side of the tower. In addition, suitable busbars are supplied for connection to the grounding kits (art. KTF...). TECHNICAL SPECIFICATIONS GENERAL DATA Weight of the station in transport condition (1) : Weight of shelter: Dimensions of shelter: Dimensions of mobile station in transport condition (bxlxh): Ground area covered in working position: Maximum height from ground: Tower supply voltage: Motor power of the tower lifting winch: Maximum power drawn by the tower: Installation time: 9500 kg 1300 kg 2.4x3.0x3.0 m 10.3x2.5x3.7 m 4.5x10.5 m 23.0-26.0 m 220 V 50 Hz 1.7 kw 6.0 kw 5 h DESIGN AND STANDARDS Design follows the most modern measuring criteria, with the aid of advanced software systems. The structural analysis and static tests conform to the most recent European (Eurocodes 1 and 3) and Italian Standards (CNR-UNI). Tests to other International Standards (EURONORM, BS, NV65, etc.) can be carried out on request. WIND LOADS The mobile station with self mounting tower can withstand a maximum equivalent surface area of antennas of 1.8 m 2 at the top. Tests are in accordance with Eurocode requirements (Wind speed = 150 km/h). The structures are also tested in accordance with Italian Standards for the various wind zones specified in D.M. (Ministerial Decree) of 16/01/96 with the operating limits indicated in the installation, use and maintenance manual. TWIST & SWAY The maximum twist at the top of the tower, with a constant wind speed of 100 km/h is less than 1. MATERIALS The materials comply with the requirements of European Standards (Euronorm). Structural parts: S235JR (Fe 360 B) EN 10025 Nuts and bolts: type 6.8. EN 20898-1 (1) Value including weight of shelter and generator. All legal rights in this document are the exclusive property of and no part of it may be reproduced or communicated to any other party without our authorization. All data in this catalogue is for reference only and may be changed without notice, in line with our policy of continuous technical development. - tel. +39 0432 84381 fax +39 0432 848997 www..it @.it - Catalogue 2004 - page 122
MOBISTAT Trailer All legal rights in this document are the exclusive property of and no part of it may be reproduced or communicated to any other party without our authorization. All data in this catalogue is for reference only and may be changed without notice, in line with our policy of continuous technical development. GALVANIZATION All materials of the self mounting tower are protected by hot-dip galvanizing in accordance with ASTM A123 and Euronorm EN 1461 Standards. STANDARD VERSIONS The mobile station with self mounting tower is available in two heights with the following characteristics: version A maximum height from ground = 23.0 m maximum wind speed in working position = 150 km/h version B maximum height from ground = 26.0 m maximum wind speed in working position = 150 km/h CATALOGUE PRODUCTS STANDARD SUPPLY Provides the minimum configuration required for commissioning of the mobile station, excluding radiant systems and their mounts. Standard supply includes: semi-trailer approved for road use tower complete with trailer and stabilisers vertical cable tray system for feeders and service cables antenna pipe mount complete with brackets for 3 panel antennas mains supply box (for electricity supply meter) guys consisting of galvanized steel cables with associated tensioners installation, use and maintenance manual. ACCESSORIES These parts are additional to those provided in the basic versions and must be ordered separately: grounding kit comprising 5 copper-plated steel rods, 1500 mm long and 40 m of bare copper conductor (cross sectional area 50 mm 2 ), complete with all necessary clamps and busbars (art. GRPI) mounts for dish antennas (art. TAMA...) aircraft warning lights, night-time obstruction light (art. S...) red/white paintwork for top third of tower, day-time obstruction warning (art. SOVD) electrical control panel (art. MECP) generating set (art. MGES...) shelter. Article MTOT 2310 MTOT 2610 Height H m 23.0 26.0 Base dimensions A B C m m m km/h 10.3 4.0 2.5 150 10.3 4.0 2.5 150 H Max wind speed B 2.6 m 3.7 m C Working position Lifting phase Transport position A 3.0 m shelter - tel. +39 0432 84381 fax +39 0432 848997 www..it @.it - Catalogue 2004 - page 123
MOBISTAT Trailer aircraft warning light system panel antennas antenna mount reinforcing struts grounding dish antennas rotation system for azimuth orientation of the antennas SELF MOUNTING TOWER guys tensioner shelter All legal rights in this document are the exclusive property of and no part of it may be reproduced or communicated to any other party without our authorization. All data in this catalogue is for reference only and may be changed without notice, in line with our policy of continuous technical development. - tel. +39 0432 84381 fax +39 0432 848997 www..it @.it - Catalogue 2004 - page 124
All legal rights in this document are the exclusive property of and no part of it may be reproduced or communicated to any other party without our authorization. All data in this catalogue is for reference only and may be changed without notice, in line with our policy of continuous technical development.
MOBISTAT Housing art. CSH.. -. compact shelter SUPPORTING MAINFRAME The shelter basically consists of a supporting mainframe made of hot extruded sections in aluminium alloy EN AW-6060 UNI EN 573-3/96, which contains and encapsulates the external cladding in order to obtain a monolithic body after manufacturing is completed. THERMAL INSULATION The thermal insulation of the shelter is ensured by polyurethane foam panels, thickness 60/80 mm (density 40 Kg/m 3 ). The value of the global heat transfer coefficient is approx. 0.5 W/m 2 K. EXTERNAL - INTERNAL LINING The external-internal lining of the walls is made of painted metal sheets. The floor covering is made of self-extinguishing PVC. ACCESS DOOR The access door is built with a frame made of aluminium. Standard dimensions of the door opening are: - height 2000 mm - width 900 mm The door is equipped with non-detachable stainless steel hinges and with a lock fitted with an anti-panic device. EQUIPMENT ROOM The equipment room is equipped with: integrated board with ac power distribution and dc power system batteries air conditioning system alarm system grounding system fire extinguishing system accessories. GROUNDING SYSTEM Shelters are equipotential and therefore all panels are electrically connected to each other and to the mainframe by a copper strip and copper plate as connection. Article CSH 01 - I CSH 02 - I CSH 03 - I CSH 01 - E CSH 02 - E CSH 03 - E Length external-internal mm 2600-2450 3200-3050 3800-3650 2600-2450 3200-3050 3800-3650 Width external-internal mm 1600-1450 1600-1450 1600-1450 1600-1450 1600-1450 1600-1450 Height external-internal mm 2750-2500 2750-2500 2750-2500 2750-2500 2750-2500 2750-2500 Weight without batteries kg 1200 1300 1450 1200 1300 1450 Air conditioning internal internal internal external external external SHELTER CSH01-E with external air-conditioning unit SOCKETS - LIGHTING and POWER SOCKETS Internal lighting is obtained by means of an emergency roof lamp with fluorescent bulb, fitted to the ceiling. A 10/16 ac UNEL socket outlet is fitted on the shelter wall. MAINS POWER DISTRIBUTION BOARD The distribution board is designed for supply and control of the various services installed. Particularly: protection and distribution of ac circuits supply of 48 V dc by means of rectifiers back-up system with batteries monitoring, control and management of the whole system supervision and signalling of alarm situations. The boards will be equipped with 34 A/48 V dc (n+1 configuration) rectifiers and two batteries and have the following main electrical characteristics: Voltage: 400/230 V ac (3-phase+Neutral) Frequency: 50 Hz Rectifiers Qty n 2+1 3+1 4+1 2+1 3+1 4+1 Battery Amperage Ah 2 x 100 2 x 160 2 x 180 2 x 100 2 x 160 2 x 180 All legal rights in this document are the exclusive property of and no part of it may be reproduced or communicated to any other party without our authorization. All data in this catalogue is for reference only and may be changed without notice, in line with our policy of continuous technical development. - tel. +39 0432 84381 fax +39 0432 848997 www..it @.it - Catalogue 2004 - page 126
MOBISTAT Housing art. CSH.. -. compact shelter All legal rights in this document are the exclusive property of and no part of it may be reproduced or communicated to any other party without our authorization. All data in this catalogue is for reference only and may be changed without notice, in line with our policy of continuous technical development. AIR CONDITIONING SYSTEM The air conditioning system is composed of compact conditioning units with free cooling function. Article CSH 01 CSH 02 Conditioning unit 4000 4000 CSH 03 6000 1600 Thermal conditions (Tint 25 C Text 35 C) W MOBISTAT Flanged Pole art. MFCO... Fan m 3 /h 1200 1200 Heating W 1000 1000 1000 The standard power supply required by these units is 230 V ac, single-phase+neutral, 50 Hz or 400 V ac, 3-phase+Neutral, 50 Hz. The dc free-cooling function is integrated in the air conditioning unit, therefore when the mains power fails, the operation of the internal dc fans is guaranteed by 48 V dc supplied by the battery set. MOBISTAT Trailer art. MTOT... WHICH SHELTERS FOR WHICH MOBILE STATIONS FIRE EXTINGUISHING SYSTEM An optical smoke detector is installed in the shelter together with a 5 kg CO 2 manual fire extinguisher positioned near the access door. ALARM SYSTEM In the power distribution board the following dry contact alarms are available: open door, max. indoor temperature, mains failure, air conditioning unit failure, smoke alarm, power system failure, battery failure. ACCESSORIES Tilting table, document pocket First aid kit C-rails and cable entries Plinths and access ladder Cable ladder MOBISTAT Flanged Pole art. MFUC... Omnishelter Mobile Unit art. MOB..-..-C1 CSH 01 - I, CSH 02 - I, CSH 03 - I CSH 01 - E, CSH 02 - E CSH 01 - I, CSH 02 - I CSH 01 - E, CSH 02 - E CSH 01 - I CSH 01 - E CSH 01 - E, CSH 02 - E, CSH 03 - E Note: if the shelter is ordered together with the mobile station, will make the necessary adjustments to the platform in order to fix the selected compact housing. - tel. +39 0432 84381 fax +39 0432 848997 www..it @.it - Catalogue 2004 - page 127
MOBISTAT Housing compact shelter 2750 mm 2750 mm 2500 mm 2750 mm 2500 mm 2500 mm air-conditioning unit 01 art. CSH 01 - I air-conditioning unit 01 art. CSH 02 - I air-conditioning unit 01 art. CSH 03 - I SE-QE BAT. SE-QE BAT. SE-QE BAT. BTS 1450 mm 2600 mm radio bridge BTS BTS radio bridge 3050 mm 3200 mm BTS BTS BTS radio bridge 3650 mm 3800 mm 1600 mm air-conditioning unit 02 1600 mm air-conditioning unit 02 1600 mm air-conditioning unit 02 All legal rights in this document are the exclusive property of and no part of it may be reproduced or communicated to any other party without our authorization. All data in this catalogue is for reference only and may be changed without notice, in line with our policy of continuous technical development. - tel. +39 0432 84381 fax +39 0432 848997 www..it @.it - Catalogue 2004 - page 128
MOBISTAT Housing compact shelter All legal rights in this document are the exclusive property of and no part of it may be reproduced or communicated to any other party without our authorization. All data in this catalogue is for reference only and may be changed without notice, in line with our policy of continuous technical development. 2750 mm 2750 mm 2500 mm 2500 mm 2750 mm 2500 mm air-conditioning unit 01 art. CSH 01 - E air-conditioning unit 01 art. CSH 02 - E air-conditioning unit 01 art. CSH 03 - E SE-QE BATT. SE-QE BATT. SE-QE BATT. air-conditioning unit 02 BTS 1450 mm 2600 mm 3050 mm 3200 mm 3650 mm 3800 mm radio bridge 1600 mm air-conditioning unit 02 BTS BTS radio bridge 1600 mm air-conditioning unit 02 BTS BTS BTS radio bridge 1600 mm - tel. +39 0432 84381 fax +39 0432 848997 www..it @.it - Catalogue 2004 - page 129
MOBISTAT Mobile Radio Stations ANTENNA MOUNTS art. TABP... pipe bracket for panel antennas Hot-dip galvanized pipe bracket, used for fixing panel or omnidirectional antennas. The item is supplied complete with fixing hardware. Article TAPB 8920 TAPB 1120 TAPB 1320 TAPB 1520 TAPB 1920 art. TAMA... 89 114 133 159 194 TAPB dimensions Ø A mm mm 200 200 200 200 200 Hot-dip galvanized pipe with adjustable bracket, to be used for fixing dish antennas up to 600 mm in diameter. This mount can be installed on tubes with diameters between 89 mm and 219 mm. The item is supplied complete with fixing hardware. art. S... Article TAMA 8915 TAMA 1521 Dimensions 89-159 159-219 Ø SIDE VIEW Ø 89-219 mm Various system configurations complying with ICAO and FAA Standards are available. Their function is to provide night-time warning of obstacles in the vicinity of airports and landing strips. For further information and ordering instructions, please consult the technical sheet Aircraft warning light system in the Clampco section on page 193. art. SOVD With regard to flight obstacle signalling, the structure will be painted as for ICAO Standards - Annex 14 (Upper third portion with red - RAL 2002; white - RAL 9010). A primer coat will be applied to a thickness of 40 microns. Finally, the primer coat will be followed by the application of two coats of epoxy paint, 40 microns each. Ø mm Ø 60 mm A PLAN VIEW Ø 114 mm SIDE VIEW 300 mm PLAN VIEW 800 mm 250 mm SUPPLY CONFIGURATION universal pipe bracket for dish antennas SUPPLY CONFIGURATION aircraft warning light system day-time warning system All legal rights in this document are the exclusive property of and no part of it may be reproduced or communicated to any other party without our authorization. All data in this catalogue is for reference only and may be changed without notice, in line with our policy of continuous technical development. - tel. +39 0432 84381 fax +39 0432 848997 www..it @.it - Catalogue 2004 - page 130
MOBISTAT Mobile Radio Stations GROUNDING PROTECTION art. GRPI grounding ring mobile station kit art. KTF... grounding kit for feeders All legal rights in this document are the exclusive property of and no part of it may be reproduced or communicated to any other party without our authorization. All data in this catalogue is for reference only and may be changed without notice, in line with our policy of continuous technical development. For further information and ordering instructions, please consult the technical sheet Grounding protection in the SITETOOLS Radio Station accessories section on page 171. art. ASBB For further information and ordering instructions, please consult the technical sheet Ballast components in the SITETOOLS Radio Station Accessories section on page 175. art. MECP The electrical control panel is protected by an IP65, doubleinsulated polyester enclosure with a solid door and triangle lock. The enclosure contains the mains/generator changeover switch, a 4-pole thermal-magnetic residual current main circuit-breaker, four thermal-magnetic circuit-breakers for services and a power socket. On the outside of the enclosure there is a 32 A, 3-pole, EEC type plug with earth and neutral, for connection to the generator. The overall dimensions of the control panel are approximately 515x650x250 mm. can supply control panels specially designed for specific requirements. art. MGES... The generating set consists of a diesel-powered motor and a 3-phase (400 V - 50Hz), synchronous, brushless alternator, with insulation class H and IP23 mechanical protection. All the equipment is fixed to a base-plate which carries both the motor and the generator, directly connected by means of a coupling and complete with vibration insulator. The fuel tank is fixed to the base-plate and has a capacity suitable for providing approximately 24 hours' operation. The generating set is supplied complete with an electrical control panel and 4-pole circuit-breaker with thermal-magnetic protection. All the equipment is enclosed in a galvanized steel, sound-proof painted container. It is available in two versions: art. MGES 1050 - Power 10 KVA art. MGES 1550 - Power 15 KVA. For further information and ordering instructions, please consult the technical sheet Grounding kits in the CLAMPCO SISTEMI Plant Accessories section on page 211. ballast blocks ADDITIONAL PARTS FOR MOBILE STATIONS electrical control panel generating set - tel. +39 0432 84381 fax +39 0432 848997 www..it @.it - Catalogue 2004 - page 131
MOBISTAT Mobile Radio Stations ADDITIONAL PARTS FOR MOBILE STATIONS art. MUPG... upgrade for permanent stations The mobile station can be converted into a fixed radio base station by modifying the arrangement of the support feet and ballast weights. Conversion is possible with a few easy steps: 1. Excavate the ground in the area under the ballast weights (which do not touch the ground) to a depth of 30-40 cm. 2. Cast concrete into the excavation to fill the area between the ballast weights and the ground, after having inserted the special steel bars. 30-40 cm excavation Article adjusting screw with flange and support plate MUPG 5151 MUPG 5656 MUPG 5252 Mobile station Model MFUC MFCO MTUC cast concrete 3. Once casting has been completed and when the concrete has reached a suitable strength, release the support feet by slackening the adjusting screws (the station will rest entirely on the ballast weights and on the cast concrete base beneath them). 4. Remove the adjusting screws with the flanges and support plates. art. FPZ... For further information and ordering instructions, please consult the technical sheet Modular supporting devices in the CLAMPCO SISTEMI Plant Accessories section on page 219. 5. Dig a hole under each foot. 6. Insert the extensions fitted with metal clamps in place of the adjusting screws. art. MUPG 7. Pour concrete into the holes to encase the extensions fitted onto the feet. Once these operations have been completed, the station becomes fixed and the cast concrete constitutes the foundation. The size of the four concrete blocks to be cast round the feet must be calculated for each individual case, taking into account the characteristics of the ground. The conversion kit includes the 4 extensions for the support feet and all necessary hardware. On request, can also supply the design for the foundation blocks. universal galvanized pin All legal rights in this document are the exclusive property of and no part of it may be reproduced or communicated to any other party without our authorization. All data in this catalogue is for reference only and may be changed without notice, in line with our policy of continuous technical development. - tel. +39 0432 84381 fax +39 0432 848997 www..it @.it - Catalogue 2004 - page 132
MOBISTAT Mobile Radio Stations CALZAVARA MOBISTAT SCHEME All legal rights in this document are the exclusive property of and no part of it may be reproduced or communicated to any other party without our authorization. All data in this catalogue is for reference only and may be changed without notice, in line with our policy of continuous technical development. MOBISTAT Flanged Pole art. MFUC... art. MFCO... Article MFUC 2051 MFUC 2351 MFUC 2651 MFCO 2456 MFCO 2756 MFCO 3056 Height H m 20.0 23.0 26.0 24.0 27.0 30.0 MOBISTAT Self Mounting Pole art. MTUC... Article Height H m A m Base dimensions A B m m km/h 5.1 5.1 5.1 5.6 5.6 5.6 Dimensions B m C m / / / 8.2 8.2 8.2 Max wind speed 160 160 160 160 160 160 Max wind speed km/h Article BORA 1750 A BORA 1750 B BORA 1750 C Article Height H m 20.5 20.5 23.0 Base dimensions Max wind speed A B m m km/h 3.9 3.9 3.9 / 7.3 7.3 MTUC 1852 MTUC 2052 18.0 20.0 5.2 5.2 2.4 2.4 4.8 4.8 130 130 MTOT 2310 MTOT 2610 23.0 26.0 10.3 10.3 4.0 4.0 2.5 2.5 150 150 - tel. +39 0432 84381 fax +39 0432 848997 www..it @.it - Catalogue 2004 - page 133 Height H m MOBISTAT Self Mounting Tower art. BORA... 130 160 160 MOBISTAT Trailer art. MTOT... Base dimensions Max wind speed A B C m m m km/h
All legal rights in this document are the exclusive property of and no part of it may be reproduced or communicated to any other party without our authorization. All data in this catalogue is for reference only and may be changed without notice, in line with our policy of continuous technical development.