Tow-Behind Spreader 175 lb Capacity IMPORTANT Read and follow all Safety Precautions and Instructions Before Operating this Equipment. MODEL NUMBER SP-175TB Made In CHINA 15912 Rev.08-273
LIMITED WARRANTY The manufacturer s warranty to the original consumer purchaser is: This product is free from defects in materials and workmanship for a period of one (1) year from the date of purchase by the original consumer purchaser. We will repair or replace, at our discretion, parts found to be defective due to materials or workmanship. This warranty is subject to the following limitations and exclusions: 1) Commercial Use Warranty period for any product used for commercial or rental is limited to ninety (90) days from date of original purchase. 2) Limitations This warranty applies only to products which have been properly assembled, adjusted, and operated in accordance with the instructions contained within this manual. This warranty does not apply to any product of Super4ce Products., that has been subject to alteration, misuse, abuse, improper assembly or installation, or shipping damage. 3) Exclusions Excluded from this warranty are normal wear, normal adjustments, and normal maintenance. In the event you have a claim under this warranty, you must return the product to an authorized service dealer. All transportation charges, damage, or loss incurred during transportation of parts submitted for replacement or repair under this warranty shall be borne by the purchaser. Should you have any questions concerning this warranty, please contact us toll-free at 1-651-330-2038. The model number, serial number, date of purchase, and the name of the authorized Super4ce dealer from whom you purchased the mower will be needed before any warranty claim can be processed. THIS WARRANTY DOES NOT APPLY TO ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES AND ANY IMPLIED WARRANTIES ARE LIMITED TO THE SAME TIME PERIODS STATED HEREIN FOR ALL EXPRESSED WARRANTIES. Some states do not allow the limitation of consequential damages or limitations on how long an implied warranty may last, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights and you may have other rights, which vary from state-to-state. This is a limited warranty as defined by the Magnuson-Moss Act of 1975. This Safety Alert Symbol indicates important messages in this manual. When you see this symbol, carefully read the message that follows and be alert to the possibility of personal injury Keep the operating speed LOW!! Do not operate over 5 MPH (8 KPH) Be sure that the area is clear before operating. Children are often attracted to the machine and operating activity. Never assume that children will remain where you last saw them. Keep children under the watchful care of another responsible adult. Read this manual and learn to operate this equipment safely. Stop and inspect the equipment if you strike an object. Repair if necessary before restarting. Dress properly. Do not operate when bare foot or wearing open sandals. Do not operate while under the influence of alcohol or drugs. Operate attachments up and down slopes. There is a significant risk of overturns when operating across slopes Oil or grease moving parts as required. 2
SAFETY PRECAUTIONS 1. Always wear safety glasses, a dust mask, and proper clothing to avoid contact with any chemicals or dangerous materials that are being applied by this spreader. 2. Always remove any contents that are in the spreader s hopper before attaching, detaching, or lifting the unit. 3. Always refer to the load rating for the towing vehicle which should be located in the vehicle s owners manual. Make sure that the weight of the unit plus the weight of the contents in the hopper do not exceed that of the vehicles recommended load rating. 4. To avoid damage to this unit and prevent personal injury NEVER load the hopper heavier than the maximum limit specified. 5. Stay clear of all moving and spinning parts of this unit. 6. Always follow directions from the package of the material you are applying with this unit. 7. This unit is not designed to spread sand or gravel. These abrasive materials can cause premature failure of the unit. Operating Instructions 1. After assembling unit, attach to the hitch of ATV or lawn tractor. 2. Read and follow directions on the package of the material being spread by this unit. 3. Fill hopper with desired material to be spread by this unit not exceeding maximum load of 175lbs. 4. Adjust the handle (Ref. #35) on the gauge assembly (Ref. #40) so that it is at the desired setting. Then tighten the wing nut (Ref. #32) on the gauge assembly to set the desired opening. This allows the driver to set the opening to the same place each time of use. 5. Begin to tow the unit to initiate spreading. 6. Always clean and dry entire unit after each use to avoid rust and corrosion from fertilizers/chemicals used. 3
1. Remove and identify loose parts from carton and bag.
ASSEMBLY INSTRUCTIONS STEP 1 1. Assemble each side of axle in this order: First flat washer Ø20, then spacer bushing, then a second flat washer Ø20, then tire, then a third flat washer Ø20 onto the end of the axle. Finally, insert the Ø4x40 cotter pin into the small hole at end of the axle, and bend cotter pin to secure. (See illustration a). 2. Repeat at the opposite side of axle. 3. On the axle side with hole Ø7 on inside of tire; put drive pin through hole of inside of wheel hub and axle. (See illustration b) STEP 2 1.Align the hole at the flat end of Hitch Tube with the hole in the middle of the Crossover Tube (the hitch tube should be on the top side of the crossover tube).loosely secure the two parts using Hex Bolt M6x50, Flat Washer Ø and Nut M6. (see illustration c) 2.Install the Adjustable Plate Support Tube on the Hitch Tube using Hex Bolt M8x50 and Lock Nut M8(see illustration d)
Step3 1. Loosely secure two Hitch Braces to the rear, horizontal hole on the hitch tube Bolt M6x50 and Nylon Nut M6.(see illustration e) 2. Loosely secure two Hitch Braces to the lowest, horizontal hole on the Adjust Plate Support Tube by using Bolt M6x50 and Nylon Nut M6. (see illustration f) 3. Loosely secure the remaining loose ends of the braces with the horizontal hole in the front bend of the Install Tube Assembly using Bolt M6x50 and Nylon Nut M6. (see illustration g) Adjust the position of Hitch Tube, Across Rod and Hitch Brace to assure proper alignment. Tighten all nuts (in illustration c-g). Step 4 1. Insert the head of Axle on Frame Tube Assembly into the Swivel Bushing at the bottom of Hopper Assembly 2. Loosely secure the Hopper Assembly to the Frame using six Bolt M6x50 with Flat Washer Ø6 and Nylon Flat Washer Ø6(washers are installed inside the hopper) and Nylok Nut M6. Adjust parts of the Hoper Assembly to assure the axle is able to turn freely. Tighten all the Nylok Nut M6. (see illustration h) 3. Insert the R Pin Ø3x75 into the hole on top of Swivel Axle. (see illustration i)
Step 5 1. Place the Hopper Screen in the Hopper Assembly (see illustration J) 2. Install the support rod into the hole in the hopper using Hex Bolts M6x20, Flat WashersØ6 and nylon washers. Step 6 1. Loosely secure Adjust Handle Assembly and Support Bar using two Bolts M8x40 and two Nylon Lock Nuts M8. 2.Install one Flat Washer Ø8 at the lower head of Adjust Rod. Then insert Adjust Rod into the hole of Rod Base. Secure them by using a Nylon Lock Nut M8. (See illustration K and L) 3.Adjust the Adjust Handle to assure the Active Adjustable Plate opens and closes properly. Then tighten all of the Nylon Lock Nuts M8.
Step 7 1. Secure the Hitch Bracket to the head of Hitch Tube using two Hex Bolts M6x50 and Nylon Lock Nuts M6. (See illustration M) Note: The length of the tongue depends on which holes are used for mounting the hitch bracket. Step8
PARTS DRAWING
Ref# Description Part Number QTY Ref# Description QTY Part Number 1 Tire/Wheel 15881 2 30 Fixing Plate for Wing Nut 1 13809 2 Spacer 15882 2 31 Nylon Flat Washer Ø6 12 NB194 3 Flat WasherØ20 14303 8 32 Wing Nut M6 1 14008 4 Bushing 15883 2 33 Hex Bolt M8x40 2 NB152 5 Cotter Pin Ø4x40 15884 2 34 Hex Bolt M6x20 5 13788 6 Swivel Axle 15885 1 35 Adjust Handle 1 15896 7 Gear (Driver) 15886 1 36 Handle Crip 1 13815 8 Spring Pin Ø4x35 15887 2 37 Big Flat WasherØ6 13 13656 9 Shaft Support Cap 15888 1 38 Bracket 1 13821 10 Drive PinØ6x50 15889 1 39 Flat WahserØ8 4 13822 11 Small Gear 13801 1 40 Bracket Flow Control Mount 1 15897 12 Turn Axle 13800 1 41 Plastic Cap 1 15898 13 Spring Pin Ø3x36 15890 1 42 Adjust Rod 1 15899 14 Screw M4x20 15891 1 43 Gauge Label 1 15900 15 Impeller 13792 1 44 Bearing 2 13785 16 Hitch Brace 13807 4 45 Fixing Adjustable Plate 1 15901 17 Hex Bolt M6x45 13666 7 46 Active Adjustable Plate 1 13787 18 Hitch Tube 15892 1 47 Fixed Plate for Connecting Rod 1 13791 19 Flow Control Rod 15893 1 48 Spring 1 13790 20 Hex Bolt M8x55 NB721 4 49 Base for Spring 1 13789 21 Nylon Flat Washer M8 10192 10 50 Hopper Screen 1 15902 22 Nylon Flat Washer M6 NB194 21 51 Support Rod 1 15903 23 Hex Bolt M8x20 NB719 2 52 RivetØ5x12 6 15904 24 R Pin Ø3X75 13647 4 53 Hex Bolt M6x50 7 13668 25 Hitch Bracket 15894 1 54 Hopper Assembly 1 15905 26 Connect Plate 12150 1 55 Mounting Tube 1 15906 27 Peg 15895 1 56 Across Rod 1 15907 28 Hex Bolt M6x40 13667 1 57 Shaft Support 1 13805 29 Screw M6x20 14791 1 58 Rain Cover 1 15908
Owner s Manual 175# Tow Behind Spreader SP175-TB ATV ACCESSORIES WHEN ORDERING PARTS, PLEASE HAVE THE FOLLOWING INORMATION AVAILABLE: * PRODUCT * SERIAL NUMBER - * MODEL NUMBER - TYPE - * PART NUMBER WITH PAINT CODE * PART DESCRIPTION TELEPHONE 1-651-330-2038 IMPORTANT Read and follow all Safety Precautions and Instructions SUPER4CE PRODUCTS PO BOX 50807 MENDOTA, MN. 55150-0807 SUPER4CE.COM Made In CHINA